Simplified formulations with high drug loads for continuous twin-screw granulation

Systematic investigation of the impact of screw elements in continuous wet granulation

Twin-screw wet granulation (TSG) is a continuous manufacturing technique either for granules as final dosage form or as an intermediate before tableting or capsule filling. A comprehensive process understanding is required to implement TSG, considering various parameters influencing granule and tablet quality. This study investigates the impact of screw configuration on granule properties followed by tableting, using a systematic approach for lactose-microcrystalline cellulose (lactose-MCC) and ibuprofen-mannitol (IBU) formulations. The most affecting factor, as observed by other researchers, was the L/S ratio impacting the granule size, strength and tabletability. Introducing tooth-mixing-elements at the end of the screw, as for the IBU formulation, resulted in a high proportion of oversized granules, with values between 36% and 78%. Increasing the thickness of kneading elements (KEs) produced denser, less friable granules with reduced tablet tensile strength. Granulation with more KEs, larger thickness or stagger angle increased torque values and residence time from 30 to 65 s. Generally, IBU granules exhibited high tabletability, requiring low compression pressure for sufficient tensile strength. At a compression pressure of 50 MPa, IBU tablets where at least one kneading zone was included resulted in approximately 2.5 MPa compared to lactose-MCC with 0.5 MPa. In conclusion, the TSG process demonstrated robustness by varying the screw design with minimal impact on subsequent tableting processes.

Characterizing a design space for a twin-screw wet granulation process: A case study of extended-release tablets

Twin-screw wet granulation is an emerging continuous manufacturing technology for solid oral dosage forms. This technology has been successfully employed for the commercial manufacture of immediate-released tablets. However, the higher polymer content in extended-release (ER) formulations may present challenges in developing and operating within a desired design space. The work described here used a systematic approach for defining the optimum design space by understanding the effects of the screw design, operating parameters, and their interactions on the critical characteristics of granules and ER tablets. The impacts of screw speed, powder feeding rate, and the number of kneading (KEs) and sizing elements on granules and tablets characteristics were investigated by employing a definitive screening design. A semi-mechanistic model was used to calculate the residence time distribution parameters and validated using the tracers. The results showed that an increase in screw speed decreased the mean residence time of the material within the barrel, while an increase in the powder feeding rate or number of KEs did the opposite and increased the barrel residence time. Screw design and operating parameters affected the flow and bulk characteristics of granules. The screw speed was the most significant factor impacting the tablet's breaking strength. The dissolution profiles revealed that granule characteristics mainly influenced the early phase of drug release. This study demonstrated that a simultaneous optimization of both operating and screw design parameters was beneficial in producing ER granules and tablets of desired performance characteristics while mitigating any failure risks, such as swelling during processing.

Faster to First-time-in-Human: Prediction of the liquid solid ratio for continuous wet granulation

In early development, when active pharmaceutical ingredient (API) is in short supply, it would be beneficial to reduce the number of experiments by predicting a suitable L/S ratio before starting the product development. The aim of the study was to decrease development time and the amount of API needed for the process development of high drug load formulations for continuous twin-screw wet granulation (TSWG). Mixer torque rheometry was used as a pre-formulation tool to predict the suitable L/S ratios for granulation experiments. Three different values that were based on the MTR curves, were determined and assessed for their ability to predict the suitable L/S ratio for TSWG. Three APIs (allopurinol, paracetamol and metformin HCl) were used as model substances in high drug load formulations containing 60% drug substance. The MCC-mannitol ratio was varied to assess the optimal composition for the high-dose formulations. The API solubility affected the mixer torque rheometer (MTR) curves and the optimum L/S ratio for TSWG. The highly soluble metformin needed a much lower L/S ratio compared with allopurinol and paracetamol. A design space was determined for each API based on granule flowability and tablet tensile strength. The flowability of the granules and tensile strength of the tablets improved with an increasing L/S ratio. The MCC-mannitol filler ratio had a significant effect on tabletability for paracetamol and metformin, and these APIs having poor compaction properties needed higher MCC ratios to achieve the 2 MPa limit. The MCC-mannitol ratio had no effect on the granule flow properties. Instead, API properties had the largest influence on both granule flow properties and tensile strength. Based on this study, both the L/S ratio and MCC-mannitol ratio are crucial in controlling the critical quality attributes in high drug load formulations processed by TSWG. The optimum flow and tablet mechanical properties were achieved when using 75:25 MCC-mannitol ratio. Both start of the slope and 2/3 of the L/S ratio at the maximum torque in MTR provided a solid guideline to aim for in a TSWG experiment.

A scaled down method for identifying the optimum range of L/S ratio in twin screw wet granulation using a regime map approach

Twin screw wet granulation (TSWG) has gained momentum in the pharmaceutical industry for effective continuous granulation of solid dosage products. Liquid-to-solid (L/S) ratio is a key process parameter affecting granule properties. Identifying an optimum range of L/S ratio while reducing the number of full scale experiments can minimize material requirements and streamline formulation and process development. In this work, microcrystalline cellulose-based (MCC) formulations of varying drug loads were granulated using a kneading element screw configuration at a wide range of L/S ratios until pasting was visually determined. Quantitative criteria based on process relevant granule size and mass % of fines were established to identify undesirable granulation conditions. Key mechanical properties of wet compacts measured using a small scale approach are discussed. The stress-strain behavior is used to predict pasting, and natural strain at peak yield stress and total work of deformation are used to identify undergranulation and overgranulation respectively. The small scale method is used to establish viable ranges of L/S ratios in advance of at-scale experiments. A quantitative predictive growth regime map is proposed based fully on small scale experiments and input process parameters. Strategies for establishing a generalized growth regime map for various systems of interest are discussed.

A Recent Update on Drug Delivery Systems for Pain Management

Pain remains a global health challenge affecting approximately 1.5 billion people worldwide. Pain has been an implicit variable in the equation of human life for many centuries considering different types and the magnitude of pain. Therefore, developing an efficacious drug delivery system for pain management remains an open challenge for researchers in the field of medicine. Lack of therapeutic efficacy still persists, despite high throughput studies in the field of pain management. Research scientists have been exploiting different alternatives to curb the adverse side effects of pain medications or attempting a more substantial approach to minimize the prevalence of pain. Various drug delivery systems have been developed such as nanoparticles, microparticles to curb adverse side effects of pain medications or minimize the prevalence of pain. This literature review firstly provides a brief introduction of pain as a sensation and its pharmacological interventions. Second, it highlights the most recent studies in the pharmaceutical field for pain management and serves as a strong base for future developments. Herein, we have classified drug delivery systems based on their sizes such as nano, micro, and macro systems, and for each of the reviewed systems, design, formulation strategies, and drug release performance has been discussed.

Continuous Twin Screw Granulation: A Review of Recent Progress and Opportunities in Formulation and Equipment Design

Continuous twin screw wet granulation is one of the key continuous manufacturing technologies that have gained significant interest in the pharmaceutical industry as well as in academia over the last ten years. Given its considerable advantages compared to wet granulation techniques operated in batch mode such as high shear granulation and fluid bed granulation, several equipment manufacturers have designed their own manufacturing setup. This has led to a steep increase in the research output in this field. However, most studies still focused on a single (often placebo) formulation, hence making it difficult to assess the general validity of the obtained results. Therefore, current review provides an overview of recent progress in the field of continuous twin screw wet granulation, with special focus on the importance of the formulation aspect and raw material properties. It gives practical guidance for novel and more experienced users of this technique and highlights some of the unmet needs that require further research.

Integrated twin-screw wet granulation, continuous vibrational fluid drying and milling: A fully continuous powder to granule line

Highly homogeneous low-dose (50 μg) tablets were produced incorporating perfectly free-flowing granules prepared by a fully integrated Continuous Manufacturing (CM) line. The adopted CM equipment consisted of a Twin-Screw Wet Granulator (TSWG), a Continuous Fluid Bed Dryer (CFBD) and a Continuous Sieving (CS) unit. Throughout the experiments a pre-blend of lactose-monohydrate and corn starch was gravimetrically dosed with 1 kg/h into the TSWG, where they were successfully granulated with the drug containing water-based PVPK30 solution. The wet mass was subsequently dried in the CFBD on a vibratory conveyor belt and finally sieved in the milling unit. Granule production efficiency was maximized by determining the minimal Liquid-to-Solid (L/S) ratio (0.11). Design of Experiments (DoE) were carried out in order to evaluate the influence of the drying process parameters of the CFBD on the Loss-on-Drying (LOD) results. The manufactured granules were compressed into tablets by an industrial tablet rotary press with excellent API homogeneity (RSD < 3%). Significant scale-up was realized with the CM line by increasing the throughput rate to 10 kg/h. The manufactured granules yielded very similar results to the previous small-scale granulation runs. API homogeneity was demonstrated (RSD < 2%) with Blend Uniformity Analysis (BUA). The efficiency of TSWG granulation was compared to High-Shear Granulation (HSG) with the same L/S ratio. The final results have demonstrated that both the liquid distribution and more importantly API homogeneity was better in case of the TSWG granulation (RSD 1.3% vs. 4.5%).

On-Demand Manufacturing of Direct Compressible Tablets: Can Formulation Be Simplified?

PURPOSE

Oral direct compressible tablets are the most frequently used drug products. Manufacturing of tablets requires design and development of formulations, which need a number of excipients. The choice of excipients depends on the concentration, manufacturability, stability, and bioavailability of the active pharmaceutical ingredients (APIs). At MIT, we developed a miniature platform for on-demand manufacturing of direct compressible tablets. This study investigated how formulations could be simplified to use a small number of excipients for a number of different API's in which long term stability is not required.

METHOD

Direct compressible tablets of five pharmaceutical drugs, Diazepam, Diphenhydramine HCl, Doxycycline Monohydrate, Ibuprofen, and Ciprofloxacin HCl, with different drug loadings, were made using direct compression in an automated small scale system.. The critical quality attributes (CQA) of the tablets were assessed for the quality standards set by the United States Pharmacopeia (USP).

RESULTS

This miniature system can manufacture tablets - on-demand from crystalline API using the minimum number of excipients required for drug product performance. All drug tablets met USP quality standards after manufacturing and after 2 weeks of accelerated stability test, except for slightly lower drug release for Ibuprofen.

CONCLUSIONS

On-demand tablets manufacturing where there is no need for long term stability using a flexible, miniature, automated (integrated) system will simplify pharmaceutical formulation design compared to traditional formulations. This advancement will offer substantial economic benefits by decreasing product time-to-market and enhancing quality.

A novel approach to support formulation design on twin screw wet granulation technology: Understanding the impact of overarching excipient properties on drug product quality attributes

The overall objective of this work is to understand how excipient characteristics influence the drug product quality attributes and process performance of a continuous twin screw wet granulation process. The knowledge gained in this study is intended to be used for Quality by Design (QbD)-based formulation design and formulation optimization. Three principal components which represent the overarching properties of 8 selected pharmaceutical fillers were used as factors, whereas factors 4 and 5 represented binder type and binder concentration in a design of experiments (DoE). The majority of process parameters were kept constant to minimize their influence on the granule and drug product quality. 27 DoE batches consisting of binary filler/binder mixtures were processed via continuous twin screw wet granulation followed by tablet compression. Multiple linear regression models were built providing understanding of the impact of filler and binder properties on granule and tablet quality attributes (i.e. 16 DoE responses). The impact of fillers on the granule and tablet responses was more dominant compared to the impact of binder type and concentration. The filler properties had a relevant effect on granule characteristics, such as particle size, friability and specific surface area. Binder type and concentration revealed a relevant influence on granule flowability and friability as well as on the compactability (required compression force during tableting to obtain target hardness). In order to evaluate the DoE models' validity, a verification of the DoE models was performed with new formulations (i.e. a new combination of filler, binder type and binder concentration) which were initially not included in the dataset used to build the DoE models. The combined PCA (principle component analysis)/DoE approach allowed to link the excipient properties with the drug product quality attributes.

3D printed orodispersible films with Aripiprazole

Three dimensional printing technology is gaining in importance because of its increasing availability and wide applications. One of the three dimensional printing techniques is Fused Deposition Modelling (FDM) which works on the basis of hot melt extrusion-well known in the pharmaceutical technology. Combination of fused deposition modelling with preparation of the orodispersible film with poorly water soluble substance such as aripiprazole seems to be extra advantageous in terms of dissolution rate. 3D printed as well as casted films were compared in terms of physicochemical and mechanical properties. Moreover, drug-free films were prepared to evaluate the impact of the extrusion process and aripiprazole presence on the film properties. X-ray diffractometry and thermal analyses confirmed transition of aripiprazole into amorphous state during film preparation using 3D printing technique. Amorphization of the aripiprazole and porous structure of printed film led to increased dissolution rate in comparison to casted films, which, however have slightly better mechanical properties due to their continuous structure. It can be concluded that fused deposition modelling is suitable technique and polyvinyl alcohol is applicable polymer for orodispersible films preparation.

A quality by design (QbD) twin-Screw extrusion wet granulation approach for processing water insoluble drugs

In this study, a Quality by Design (QbD) approach was used to identify the effect of formulation parameters in a twin screw wet extrusion granulation process for the manufacturing of ibuprofen (IBU) granules with increased dissolution rates. A fractional factorial Design of Experiment (DoE) was used to investigate the effect of the excipient composition, binder amount and liquid to solid (L/S) ratio (independent variables) on drug dissolution rates, median particle size diameter and specific surface area (dependent variables). The intra-granular addition of the binder in inorganic/polymer blends processed with ethanol as granulating liquids facilitated the formation of granules at various particle sizes. DoE regression analysis showed that all formulation parameters affect the dependent variables significantly. The enhanced dissolution rates were attributed not only to the IBU particle size reduction and adsorption in the porous inorganic network but also to the high specific surface area of the produced granules. Dynamic vapour sorption showed increased water absorption for granules with small particle size distribution and high specific surface area.

A novel methodology to study polymodal particle size distributions produced during continuous wet granulation

It is important during powder granulation to obtain particles of a homogeneous size especially in critical situations such as pharmaceutical manufacture. To date, homogeneity of particle size distribution has been defined by the use of the d50 combined with the span of the particle size distribution, which has been found ineffective for polymodal particle size distributions. This work focuses on demonstrating the limitations of the span parameter to quantify homogeneity and proposes a novel improved metric based on the transformation of a typical particle size distribution curve into a homogeneity factor which can vary from 0 to 100%. The potential of this method as a characterisation tool has been demonstrated through its application to the production of granules using two different materials. The workspace of an 11mm twin screw granulator was defined for two common excipients (α-lactose monohydrate and microcrystalline cellulose). Homogeneity of the obtained granules varied dramatically from 0 to 95% in the same workspace, allowing identification of critical process parameters (e.g. feed rate, liquid/solid ratio, torque velocities). In addition it defined the operational conditions required to produce the most homogeneous product within the range 5μm-2.2mm from both materials.

Identifying overarching excipient properties towards an in-depth understanding of process and product performance for continuous twin-screw wet granulation

The overall objective of this work is to understand how excipient characteristics influence the process and product performance for a continuous twin-screw wet granulation process. The knowledge gained through this study is intended to be used for a Quality by Design (QbD)-based formulation design approach and formulation optimization. A total of 9 preferred fillers and 9 preferred binders were selected for this study. The selected fillers and binders were extensively characterized regarding their physico-chemical and solid state properties using 21 material characterization techniques. Subsequently, principal component analysis (PCA) was performed on the data sets of filler and binder characteristics in order to reduce the variety of single characteristics to a limited number of overarching properties. Four principal components (PC) explained 98.4% of the overall variability in the fillers data set, while three principal components explained 93.4% of the overall variability in the data set of binders. Both PCA models allowed in-depth evaluation of similarities and differences in the excipient properties.

Continuous manufacturing via hot-melt extrusion and scale up: regulatory matters

Currently, because globalization, the pharmaceutical industry is facing enormous challenges to comply with regulatory matters. Reduced patent life and overall decreased profitability of newly discovered drugs are also forcing the pharmaceutical industry to shorten the drug development time with maximum throughput. Therefore, continuous manufacturing (CM) processes via hot melt extrusion (HME) can be a promising alternative for achieving these goals. HME offers solvent-free green technology with a process that is easy to scale up. Moreover, CM provides better product quality assurance compared with batch processes, with fewer labor costs and shorter time to development. In this review, we primarily focus on various aspects of CM and the emerging application of HME to bridge the current manufacturing gap in pharmaceutical sphere.

How Deformation Behavior Controls Product Performance After Twin Screw Granulation With High Drug Loads and Crospovidone as Disintegrant

This study addresses the quantitative influence of 12 different materials (active pharmaceutical ingredients and excipients as surrogate active pharmaceutical ingredients) on the critical quality attributes of twin screw granulated products and subsequently produced tablets. Prestudies demonstrated the significant influence of the chosen model materials (in combination with crospovidone) on the disintegration behavior of the resulting tablets, despite comparable tablet porosities. This study elucidates possible reasons for the varying disintegration behavior by investigating raw material, granule, and tablet properties. An answer could be found in the mechanical properties of the raw materials and the produced granules. Through compressibility studies, the materials could be classified into materials with high compressibility, which deform rather plastically under compression stress, and low compressibility, which display breakages under compression stress. In general, and apart from (pseudo)-polymorphic transformations, brittle materials featured excellent disintegration performance, even at low resulting tablet porosities <8%, whereas plastically deformable materials mostly did not reveal any disintegration. These findings must be considered in the development of simplified formulations with high drug loads, in which the active pharmaceutical ingredient predominantly defines the deformation behavior of the granule.

Continuous twin screw granulation of controlled release formulations with various HPMC grades

HPMC is a popular matrix former to formulate tablets with extended drug release. Tablets with HPMC are preferentially produced by direct compression. However, granulation is often required prior to tableting to overcome poor flowability of the formulation. While continuous twin screw granulation has been extensively evaluated for granulation of immediate release formulations, twin screw granulation of controlled release formulations including the dissolution behavior of the formulations received little attention. Therefore, the influence of the HPMC grade (viscosity and substitution degree) and the particle size of theophylline on critical quality attributes of granules (continuously produced via twin screw granulation) and tablets was investigated in the current study. Formulations with 20 or 40% HPMC, 20% theophylline and lactose were granulated with water at fixed process parameters via twin screw granulation. The torque was influenced by the viscosity and substitution degree of HPMC, but was not a limiting factor for the granulation process. An optimal L/S ratio was selected for each formulation based on the granule size distribution. The granule size distributions were influenced by the substitution degree and concentration of HPMC and the particle size of theophylline. Raman and UV spectroscopic analysis on 8 sieve fractions of granules indicated an inhomogeneous distribution of theophylline over the size fractions. However, this phenomenon was not correlated with the hydration rate or viscosity of HPMC. Controlled release of theophylline could be obtained over 24h with release profiles close to zero-order. The release of theophylline could be tailored via selection of the substitution degree and viscosity of HPMC.