Formulation and process strategies to minimize coat damage for compaction of coated pellets in a rotary tablet press: A mechanistic view

Tableting of coated multiparticulates: Influences of punch face configurations

The influences of the punch face design on multi-unit pellet system (MUPS) tablets were investigated. Drug-loaded pellets coated with sustained release polymer based on ethylcellulose or acrylic were compacted into MUPS tablets. Punch face designs used include standard concave, deep concave, flat-faced bevel edge and flat-faced radius edge. MUPS tablets compacted at 2 or 8 kN were characterized for their tensile strength. The extent of pellet coat damage after tableting was evaluated from drug release profiles. Biconvex tablets were weaker by 0.01-0.15 MPa, depending on the pellet type used, and had 1-17 % higher elastic recovery (p < 0.000) than flat-faced tablets. At higher compaction force, the use of the deep concave punch showed a 13-26 % lower extent of pellet coat damage, indicated by a relatively higher mean dissolution time, compared to other punch face configurations (p < 0.000). This was attributed to increased rearrangement energy of the compacted material due to the high punch concavity, which sequestered compaction stress exerted on pellet coats. Although the deep concave punch reduced the stress, the resultant tablets containing pellets coated with acrylic were weaker (p = 0.01). Overall, the punch face configuration significantly affected the quality of MUPS tablets.

Cushion-coated pellets for tableting without external excipients

Multiple-unit dosage forms prepared by compacting pellets offer important manufacturing and compliance advantages over pellet-filled capsules. However, compaction may negatively affect the release control mechanism of pellets, and subunits may not be readily available after intake. Application of a cushioning layer to the starting units is here proposed as a strategy to obtain tablets with satisfactory mechanical strength, rapid disintegration and maintenance of the expected release profile of individual subunits while avoiding the use of mixtures of pellets and excipients to promote compaction and limit the impact of the forces involved. Cushion-coating with PEG1500, a soft and soluble material, was proved feasible provided that the processing temperature was adequately controlled. Cushioned gastro-resistant pellets were shown to consolidate under relatively low compaction pressures, which preserved their inherent release performance after tablet disintegration. Adhesion problems associated with the use of PEG1500 were overcome by applying an outer Kollicoat® IR film. Through design of experiment (DoE), robustness of the proposed approach was demonstrated, and the formulation as well as tableting conditions were optimized. The tableted cushion-coated pellet systems manufactured would allow a relatively high load of modified-release units to be conveyed, thus setting out a versatile and scalable approach to oral administration of multiple-unit dosage forms.

An evaluation of microcrystalline cellulose attributes affecting compaction-induced pellet coat damage through a multi-faceted analysis

Pellet coat damage in multi-unit pellet system (MUPS) tablets has previously been studied and addressed with limited success. The effects of lactose filler material attributes on pellet coat damage have been relatively well-studied but a similar understanding of microcrystalline cellulose (MCC) is lacking notwithstanding its high cushioning potential. Hence, the relationships between MCC attributes and pellet coat damage were investigated. Single pellet in minitablets (SPIMs) were used to isolate pellet-filler effects and reveal the under-unexplored impact of risk factors found in MUPS tablets. MUPS tablets and SPIMs were prepared with various grades of MCC and pellets with an ethylcellulose or acrylic coat at various compaction pressures. Subsequently, the extent of pellet coat damage was determined by dissolution test and quantified using two indicators to differentiate the nature of the damage. A multi-faceted analytical approach incorporated linear regression, correlations and a classification and regression tree algorithm and evaluated how MCC attributes, such as flowability, particle size and plastic deformability, exert various influences on the extent of ethylcellulose and acrylic pellet coat damage. This analysis improved the understanding of the different mechanisms by which pellet coat damage to these two polymer types occurs which can help enhance future pellet coat damage mitigation strategies.

MUPS Tableting-Comparison between Crospovidone and Microcrystalline Cellulose Core Pellets

Multi-unit pellet system (MUPS) tablets were fabricated by compacting drug-loaded pellets of either crospovidone or microcrystalline cellulose core. These pellets were produced by extrusion-spheronization and coated with ethylcellulose (EC) for a sustained drug release function. Coat damage due to the MUPS tableting process could undermine the sustained release function of the EC-coated pellets. Deformability of the pellet core is a factor that can impact the extent of pellet coat damage. Thus, this study was designed to evaluate the relative performance of drug-loaded pellets prepared with either microcrystalline cellulose (MCC) or crospovidone (XPVP) as a spheronization aid and were comparatively evaluated for their ability to withstand EC pellet coat damage when compacted. These pellets were tableted at various compaction pressures and pellet volume fractions. The extent of pellet coat damage was assessed by the change in drug release after compaction. The findings from this study demonstrated that pellets spheronized with XPVP had slightly less favorable physical properties and experienced comparatively more pellet coat damage than the pellets with MCC. However, MUPS tablets of reasonable quality could successfully be produced from pellets with XPVP, albeit their performance did not match that of vastly mechanically stronger pellets with MCC at higher compaction pressure.

Mathematical approaches for powders and multiparticulate units processability characterization in pharmaceutical development

An understanding of material properties and processing effects on solid dosage forms performance is required within the Quality-by-design approach to pharmaceutical development. Several research groups have developed mathematical approaches aiming to facilitate the selection of formulation composition and the manufacturing technology. These approaches are based on material particulate, bulk and compression-related properties. This paper provides theoretical assumptions and a critical review of different mathematical approaches for processability characterization of powders and multiparticulate units. Mathematical approaches have mainly been developed for directly compressible materials, but sometimes other manufacturing technologies, such as roller compaction and wet granulation, are also considered. The obtained compact tensile strength has been implemented in the majority of approaches, as an important characteristic describing compact mechanical properties. Flowability should be also evaluated, since it affects sample processability. Additionally, particle size and shape, material density and compressibility, compactibility and tabletability profiles have been also distinguished as relevant properties for solid dosage form development. The application of mathematical approaches may contribute to the mechanistic understanding of critical material attributes and facilitate dosage form development and optimization. However, it is essential to select the appropriate one, based on the intended dosage form characteristics, in order to ensure that all relevant powder/multiparticulate units characteristics are implemented and critically evaluated.

Comparative Evaluation of Pellet Cushioning Agents by Various Imaging Techniques and Dissolution Studies

Most of the commercially available pharmaceutical products for oral administration route are marketed in the tablet dosage forms. However, compression of multiparticulate systems is a challenge for the pharmaceutical research and industry, especially if the individual unit is a coated particle, as the release of the active ingredient depends on the integrity of the coating. In the present study, polymer-coated pellets tableted with different types of excipients (powder, granules, pellets) then were investigated by various tablet-destructive (microscopic) and tablet non-destructive (microfocus X-ray; microCT) imaging methods. The information obtained from the independent evaluation of the in vitro drug release profiles model is confirmed by the results obtained by image analysis, regardless of whether X-ray or stereomicroscopic images of the coated, tableted pellets were used for image analysis. The results of this study show that the novel easy-to-use, fast, and non-destructive MFX method is a good alternative to the already used microscopic image analysis methods regarding the characterization of particulates, compressed into tablets.

Application of Dominance-Based Rough Set Approach for Optimization of Pellets Tableting Process

Multiple-unit pellet systems (MUPS) offer many advantages over conventional solid dosage forms both for the manufacturers and patients. Coated pellets can be efficiently compressed into MUPS in classic tableting process and enable controlled release of active pharmaceutical ingredient (APIs). For patients MUPS are divisible without affecting drug release and convenient to swallow. However, maintaining API release profile during the compression process can be a challenge. The aim of this work was to explore and discover relationships between data describing: composition, properties, process parameters (condition attributes) and quality (decision attribute, expressed as similarity factor f₂) of MUPS containing pellets with verapamil hydrochloride as API, by applying a dominance-based rough ret approach (DRSA) mathematical data mining technique. DRSA generated decision rules representing cause–effect relationships between condition attributes and decision attribute. Similar API release profiles from pellets before and after tableting can be ensured by proper polymer coating (Eudragit^® NE, absence of ethyl cellulose), compression force higher than 6 kN, microcrystalline cellulose (Avicel^® 102) as excipient and tablet hardness ≥42.4 N. DRSA can be useful for analysis of complex technological data. Decision rules with high values of confirmation measures can help technologist in optimal formulation development.

Cushioning pellets based on microcrystalline cellulose - Crospovidone blends for MUPS tableting

Compaction of multiple-unit pellet system (MUPS) tablets has been extensively reported to be potentially challenging. Thus, there is a need for non-segregating cushioning agents to mitigate the deleterious effect of the compaction forces. This study was designed to investigate the use of porous pellets as cushioning agents using different drying techniques to prepare pellets of various porosities and of different formulations. The pellets fabricated were characterized for their porosity and crushing strength. Subsequently, MUPS tablets were prepared using blends of polymer-coated pellets and custom-designed cushioning pellets by compacting at different pressures. The effects of pellet volume fraction and dwell time on the pellet coat damage, as well as the tensile strength of the resultant MUPS tablets were also investigated. Compacts with coated pellet volume fraction of 0.21 exhibited the best cushioning effect when tableted at different compression speeds with both gravity and force feeders. The findings from this study showed that cushioning pellet porosity was highest when drying was carried out by freeze drying, followed by fluid bed drying and oven drying. There was an inverse relationship between cushioning pellet porosity and strength. The tensile strength of tablets prepared from freeze dried pellets was highest. The protective effect of the cushioning pellets was principally dependent on their porosity. Also, pellet volume fraction in the compacts and compaction pressure used had remarkable effect on pellet coat damage. When unprocessed powders were compacted by automatic die filling, capping and lamination problems were observed. However, tablets of reasonable quality were made with the cushioning pellets. Freeze dried pellets containing crospovidone were found to be promising as cushioning agents and had enabled the production of MUPS tablets even at higher compaction pressures, beyond the intrinsic crushing strength of the coated pellets.

Influence of the porosity of cushioning excipients on the compaction of coated multi-particulates

The compaction of multiple unit-pellet system (MUPS) tablets poses considerable challenges due to potential compaction-induced damage to the functional polymer coat and segregation of pellets from other excipients during the tableting process. This study was designed to investigate the impact of porous pellets as cushioning agent without issues related to segregation while tableting. Different drying techniques were applied to produce microcrystalline cellulose (MCC) pellets with various porosities. Sodium chloride was also added to the pellet formulation as a pore forming agent to generate a porous skeleton after production and aqueous extraction. The pellets fabricated were characterized for their porosity, crushing strength and yield pressure. Tablets were prepared using unlubricated pellets and their tensile strengths determined. Blends containing polymer-coated pellets and cushioning pellets of various porosities were compacted at different compaction pressures. The porous pellets exhibiting the best cushioning effect were used for MUPS tableting at different compression speeds with both gravity and force feeders. The findings from this study showed that pellet porosity was highest when drying was carried out in a freeze dryer, followed by fluid bed and least porous from the oven. There was an inverse relationship between pellet porosity and strength. The protective effect of cushioning pellets was mainly dependent on their porosity. The porosity of pellets manufactured by leaching NaCl from MCC-NaCl (1:1) pellets were 2.14-, 2.57- and 4.88-fold higher than that of MCC PH101 only pellets for oven, fluid bed and freeze dried pellets, respectively. Although the porosity of MCC PH101-NaCl (1:3) pellets was highest, they exhibited less cushioning effect than MCC PH101-NaCl (1:1). It was inferred that a good balance between porosity and bulk density of cushioning pellets was essential to be effective at protecting the coated pellets from damage during compaction. Compared with MUPS tablets prepared using unprocessed MCC PH105, the tablets prepared with the porous freeze dried MCC PH101 (NaCl fraction leached) pellets had improved drug content uniformity and were mechanically stronger.

A mechanistic understanding of compression damage to the dissolubility of coated pellets in tablets

Damage to the drug diffusion coat barrier of controlled release pellets by the compaction force when preparing multiple-unit pellet system tablets is a major concern. Previous studies have shown that pellets located at the tablet axial and radial peripheral surfaces were more susceptible to damage when compacted due to the considerable shear encountered at these locations. Hence, this study was designed to assess with precision the impact of pellet spatial position in the compact on the extent of coat damage by the compaction force via a single pellet in minitablet (SPIM) system. Microcrystalline cellulose (MCC) pellet cores were consecutively coated with a drug layer followed by a sustained release layer. Chlorpheniramine maleate was the model drug used. Using a compaction simulator, the coated pellets were compacted singly into 3 mm diameter SPIMs with MCC as the filler. SPIMs with individual pellets placed in seven positions were prepared. The uncompacted and compacted coated pellets, as SPIMs, were subjected to drug release testing. The dissolution results showed that pellets placed at the top-radial position were the most susceptible to coat damage by the compaction force, while pellets positioned within the minitablet at the middle and upper quadrant positions showed the least damage. The SPIM system was found to be effective at defining the extent of coat damage to the pellet spatial position in the compact. This study confirmed that coated pellets located at the periphery were more susceptible to damage by compaction, with pellets located at the top-radial position showing the greatest extent of coat damage. However, if the pellet was completely encrusted by the cushioning filler, coat damage could be mitigated. Further investigations were directed at how the extent of coat damage impacted drug release. Interestingly, small punctures were found to be most detrimental to drug release whilst coats with large surface cuts did not completely fail. A damaged pellet coat has some self-sealing ability and failure is not total. Thus, this study provides a deeper understanding of the consequence of coat damage to drug release when sustained release coated pellets are breached.

Topical Inserts: A Versatile Delivery Form for HIV Prevention

The development of topical inserts for the prevention of sexually transmitted infections (STIs), particularly human immunodeficiency virus (HIV), represents a promising alternative to oral and parenteral pre-exposure prophylaxis (PrEP) dosage forms. They may be used for vaginal and/or rectal administration of a variety of agents with antiviral activity. Topical inserts deliver drugs to the portal of viral entry, i.e., the genital or rectal mucosa, with low systemic exposure, and therefore are safer and have fewer side effects than systemic PrEP agents. They may dissolve fast, releasing the active drugs within minutes of insertion, or slowly for long-acting drug delivery. Furthermore, they are user-friendly being easy to administer, discreet and highly portable. They are also economical and easy to manufacture at scale and to distribute, with excellent stability and shelf-life. Altogether, topical inserts represent a particularly promising form of drug delivery for HIV and STI prevention. Highlighted within this review are end-user acceptability research dedicated to understanding preferred attributes for this form of drug delivery, advantages and disadvantages of the formulation platform options, considerations for their development, clinical assessment of select placebo prototypes, future directions, and the potential impact of this dosage form on the HIV prevention landscape.

Studying the factors that impact the dissolution characteristic of complex drug product

This article summarizes the critical factors involved in product development of a single dosage form formulated by compacting ethyl cellulose (EC) coated controlled release pellets into a tablet. The greatest challenge associated with this type of complex system is to minimize the effect of compression on the drug release. The effects of compression on the drug release were optimized with combination of the following factors (1) particle size of the core pellets, (2) the selection of the coating polymer's viscosity grade, and (3) emergence of cushioning agents. The optimization of these factors provided superior protection for the controlled release coated pellets; therefore, the desired drug release from the tablet was successfully achieved as designed. However, the drug release rates from the coated pellets before and after the compression were minimized and exhibited only a slight difference.

Oral Modified Release Multiple-Unit Particulate Systems: Compressed Pellets, Microparticles and Nanoparticles

Oral modified-release multiparticulate dosage forms, which are also referred to as oral multiple-unit particulate systems, are becoming increasingly popular for oral drug delivery applications. The compaction of polymer-coated multiparticulates into tablets to produce a sustained-release dosage form is preferred over hard gelatin capsules. Moreover, multiparticulate tablets are a promising solution to chronic conditions, patients’ adherence, and swallowing difficulties if incorporated into orodispersible matrices. Nonetheless, the compaction of multiparticulates often damages the functional polymer coat, which results in a rapid release of the drug substance and the subsequent loss of sustained-release properties. This review brings to the forefront key formulation variables that are likely to influence the compaction of coated multiparticulates into sustained-release tablets. It focusses on the tabletting of coated drug-loaded pellets, microparticles, and nanoparticles with a designated section on each. Furthermore, it explores the various approaches that are used to evaluate the compaction behaviour of particulate systems.

Tablets of multi-unit pellet system for controlled drug delivery

The tablet of multi-unit pellet system (TMUPS), using coated pellets, for controlled release of drugs is an effective therapeutic alternative to conventional immediate-release dosage forms. The main advantages of TMUPS include a) ease of swallowing and b) divisible without compromising the drug release characteristics of the individual units. TMUPS can be prepared more economically than pellet-filled capsules because of the much higher production rate of tableting process. In spite of the superiorities of TMUPS, its adoption has been challenged by manufacturing problems, such as compromised integrity of coated pellets and poor content uniformity. Herein, we provide an updated review on research, from both scientific literatures and patents, related to the compaction of TMUPS. Factors important for the successful production of TMUPS are summarized, including model drug property, potential cushioning agents, and novel techniques to protect pellets from damage. This review is intended to facilitate the future development of manufacturable TMUPS with drug release behavior similar to that of the original coated pellets.

Transparent computational intelligence models for pharmaceutical tableting process

Purpose

Pharmaceutical industry is tightly regulated owing to health concerns. Over the years, the use of computational intelligence (CI) tools has increased in pharmaceutical research and development, manufacturing, and quality control. Quality characteristics of tablets like tensile strength are important indicators of expected tablet performance. Predictive, yet transparent, CI models which can be analysed for insights into the formulation and development process.

Methods

This work uses data from a galenical tableting study and computational intelligence methods like decision trees, random forests, fuzzy systems, artificial neural networks, and symbolic regression to establish models for the outcome of tensile strength. Data was divided in training and test fold according to ten fold cross validation scheme and RMSE was used as an evaluation metric. Tree based ensembles and symbolic regression methods are presented as transparent models with extracted rules and mathematical formula, respectively, explaining the CI models in greater detail.

Results

CI models for tensile strength of tablets based on the formulation design and process parameters have been established. Best models exhibit normalized RMSE of 7 %. Rules from fuzzy systems and random forests are shown to increase transparency of CI models. A mathematical formula generated by symbolic regression is presented as a transparent model.

Conclusions

CI models explain the variation of tensile strength according to formulation and manufacturing process characteristics. CI models can be further analyzed to extract actionable knowledge making the artificial learning process more transparent and acceptable for use in pharmaceutical quality and safety domains.