The relevance of granule fragmentation on reduced tabletability of granules from ductile or brittle materials produced by roll compaction/dry granulation

Critical review on the role of excipient properties in pharmaceutical powder-to-tablet continuous manufacturing

INTRODUCTION

The pharmaceutical industry is gradually changing batch-wise manufacturing processes to continuous manufacturing processes, due to the advantages it has to offer. The final product quality and process efficiency of continuous manufacturing processes is among others impacted by the properties of the raw materials. Existing knowledge on the role of raw material properties in batch processing is however not directly transferable to continuous processes, due to the inherent differences between batch and continuous processes.

AREAS COVERED

A review is performed to evaluate the role of excipient properties for different unit operations used in continuous manufacturing processes. Unit operations that will be discussed include feeding, blending, granulation, final blending, and compression.

EXPERT OPINION

Although the potency of continuous manufacturing is widely recognized, full utilization still requires a number of challenges to be addressed effectively. An expert opinion will be provided that discusses those challenges and potential solutions to overcome those challenges. The provided overview can serve as a framework for the pharmaceutical industry to push ahead process optimization and formulation development for continuous manufacturing processes.

Evaluation of binders in twin-screw wet granulation - Optimization of tabletability

The influence of hydroxypropyl cellulose type (HPC-SSL SFP, HPC-SSL), concentration (2 %, 3.5 %, 5 %) and filler (lactose, calcium hydrogen phosphate (DCP)/microcrystalline cellulose (MCC)) on twin-screw wet granulation and subsequent tableting was studied. The aim was to identify the formulation of the highest tabletability which still fulfills the requirements of the disintegration. Lactose combined with 5 % binder enabled a higher tabletability and a faster disintegration than DCP/MCC. It was found that tabletability of lactose formulations can be increased by higher binder concentration and higher compression pressure while tabletability of DCP/MCC formulations can be only increased by higher compression pressure. It was observed that batches containing DCP/MCC failed the disintegration test, if the highest binder concentration and the highest compression pressure were used. To ensure a fast disintegration, the compression pressure or at least the binder concentration had to be low. Changing the disintegrant and its localization improved the DCP/MCC formulation, resulting in faster disintegration than lactose tablets. However, it also resulted in a lower tabletability. In this study best tablets were achieved with 3.5 % or 5 % binder and lactose as filler. These tablets presented the highest tabletability but still disintegrated in less than 500 s.

Systematic DOE Approach for Dry Granulation Study at Early Clinical Stage of Novel Drugs: An Industrial Case

In order to introduce a cost-effective strategy method for commercial scale dry granulation at the early clinical stage of drug product development, we developed dry granulation process using formulation without API, fitted and optimized the process parameters adopted Design of Experiment (DOE). Then, the process parameters were confirmed using one formulation containing active pharmaceutical ingredient (API). The results showed that the roller pressure had significant effect on particle ratio (retained up to #60 mesh screen), bulk density and tapped density. The roller gap had significant influence on particle ratio and specific energy. The particle ratio was significantly affected by the mill speed (second level). The tabletability of the powder decreased after dry granulation. The effect of magnesium stearate on the tabletability was significant. In the process validation study, the properties of the prepared granules met the requirements for each response studied in the DOE. The prepared tablets showed higher tensile strength, good content uniformity of filled capsules, and the dissolution profiles of which were consistent with that of clinical products. This drug product process development and research strategies could be used as a preliminary experiment for the dry granulation process in the early clinical stage.

Elucidating the Impact of Material Properties on Tablet Manufacturability for Binary Paracetamol Blends

PURPOSE

Although the mechanical properties of paracetamol and MCC are extensively described in literature, there still is a need for a better understanding of the material properties impacting them. Thus, this study systematically analyzed material properties of paracetamol-MCC blends to elucidate their influence on the mechanical tablet properties in roller compaction and direct compression with special focus on surface properties.

METHODS

Multiple material characteristics of binary mixtures of paracetamol and MCC with varying drug loads were analyzed, with particular emphasis on specific surface area and surface energy. Subsequently, mechanical tablet properties of the materials in direct compression and after roller compaction were examined.

RESULTS

It was demonstrated that the impact of the initial material properties on mechanical tablet properties prevailed over the impact of processing route for paracetamol-MCC blends, underlining the importance of material characterization for tabletability of oral solid dosage forms. By applying bivariate as well as multivariate analysis, key material properties influencing the tabletability of paracetamol, MCC and its mixtures such as surface area, surface energy, effective angle of internal friction and density descriptors were identified.

CONCLUSIONS

This study highlighted the importance of comprehensive assessment of different material characteristics leading to a deeper understanding of underlying factors impacting mechanical tablet properties in direct compression and after roller compaction by the example of paracetamol-MCC mixtures with varying drug loads. Furthermore, it was shown that multivariate analysis could be a valuable extension to common bivariate analysis to reveal underlying correlations of material properties.

A tabletability change classification system in supporting the tablet formulation design via the roll compaction and dry granulation process

In this paper, the material library approach was used to uncover the pattern of tabletability change and related risk for tablet formulation design under the roll compaction and dry granulation (RCDG) process. 31 materials were fully characterized using 18 physical parameters and 9 compression behavior classification system (CBCS) parameters. Then, each material was dry granulated and sieved into small granules (125-250 μm) and large granules (630-850 μm), respectively. The compression behavior of granules was characterized by the CBCS descriptors, and were compared with that of ungranulated powders. The relative change of tabletability (CoTr) index was used to establish the tabletability change classification system (TCCS), and all materials were classified into three types, i.e. loss of tabletability (LoT, Type I), unchanged tabletability (Type II) and increase of tabletability (Type III). Results showed that approximately 65% of materials presented LoT, and as the granules size increased, 84% of the materials exhibited LoT. A risk decision tree was innovatively proposed by joint application of the CBCS tabletability categories and the TCCS tabletability change types. It was found that the LoT posed little risk to the tensile strength of the final tablet, when Category 1 or 2A materials, or Category 2B materials with Type II or Type III change of tabletability were used. Formulation risk happened to Category 2C or 3 materials, or Category 2B materials with Type I change of tabletability, particularly when high proportions of these materials were involved in tablet formulation. In addition, the risk assessment results were verified in the material property design space developed from a latent variable model in prediction of tablet tensile strength. Overall, results suggested that a combinational use of CBCS and TCCS could aid the decision making in selecting materials for tablet formulation design via RCDG.

Effects of tableting process parameters and powder lubrication levels on tablet surface temperature and moisture content

Punch sticking is a recurrent problem during the pharmaceutical tableting process. Powder moisture content plays a key role in the buildup of sticking; it evaporates due to increased tablet temperature, accumulates at the punch-tablet interface, and causes sticking through capillary force. This study investigated the effects of compaction pressure (CP), compaction speed (CS), and lubrication level (magnesium stearate (MgSt) ratio) on tablet surface temperature (TST) and tablet surface moisture content (TSMC). TST and TSMC were measured with an infrared thermal camera and near-infrared sensor, respectively. Microcrystalline cellulose was used as the tableting powder and MgSt as the lubricant. The low range of CS values (16-32 mm/s) considered in this study did not have significant effects on TST and TSMC. MgSt ratio had a significant positive effect on TST; this may be explained by the increase in powder blend effusivity with the addition of MgSt. However, MgSt ratio did not have a significant effect on TSMC. CP had a significant positive effect on both TST and TSMC. Increased CP induced higher heat generation through particle deformation and friction during the compaction phase, leading to increased TST. Furthermore, the water vapor diffusion rate through the powder bed might have increased due to the rise in thermal energy and led to further moisture accumulation at the tablet-punch interface, causing the significant positive effect of CP on TSMC. This result may explain the occurrence of sticking regardless of the CP applied during the tableting process.

Lactose in tablets: Functionality, critical material attributes, applications, modifications and co-processed excipients

Lactose is one of the most widespread excipients used in the pharmaceutical industry. Because of its water solubility and acceptable flowability, lactose is generally added into tablet formulation to improve wettability and undesirable flowability. Based on Quality by Design, a better understanding of the critical material attributes (CMAs) of raw materials is beneficial in guiding the improvement of tablet quality and the development of lactose. Additionally, the modifications and co-processing of lactose can introduce more-desirable characteristics to the resulting particles. This review focuses on the functionality, CMAs, applications, modifications and co-processing of lactose in tablets.

Terahertz time-domain spectroscopy for the investigation of tablets prepared from roller compacted granules

Roller compaction before tableting is a common unit operation to increase the processability of powders. Terahertz time-domain spectroscopy (THz-TDS) has recently been introduced as a potential process analytical technology (PAT) for measuring tablet porosity based on the refractive index of the tablet. Tablet porosity is a governing parameter for tablet disintegration and dissolution. The first aim of this study was to investigate tablets prepared from roller-compacted materials with THz-TDS to explore its usefulness for particle size evaluation of granules in tablets. Secondly, the impact of roller compaction and granule size before tablet compression on the established THz-TDS based measurement of tablet porosity was investigated. Microcrystalline cellulose and α-lactose monohydrate were roller compacted separately at five specific compaction forces (2, 4, 8, 12, and 16 kN cm-1) and fractionated into three size fractions. Tablets were prepared from the fractionated and unfractionated granules at twelve tableting pressures and subjected to THz-TDS transmission measurements. It was possible to use the scattering behaviour of the tablets at terahertz frequencies to describe the granulated materials' particle size changes during tableting. At the same time, prediction of porosity was impaired due to the deviation of the refractive index in strongly scattering samples. A correction method was introduced in which the porosity error was corrected based on the tablet's scattering behaviour, resulting in an improved prediction of tablet porosity. In conclusion, THz-TDS is considered a promising technique for the process monitoring of tableting based on its sensitivity to porosity and particle size changes within the tablet non-destructively, with a possible application as part of an in-process control strategy of the tableting of granulated or non-granulated materials.

Attribute transmission and effects of diluents and granulation liquids on granule properties and tablet quality for high shear wet granulation and tableting process

This study aims to examine (i) the effect of diluent types (lactose monohydrate, corn starch, and microcrystalline cellulose) and granulation liquids (20% polyvinylpyrrolidone-k30, 65% alcohol, and dispersion containing 40% model drug- Pithecellobium clypearia Benth extracted powder) on granule properties and tablet quality for high shear wet granulation and tableting (HSWG-T) and, more importantly, (ii) the attribute transmission in the process. In general, the impact of diluents on granule properties and tablet quality was more dominant than that of granulation liquids. Attribute transmission patterns were revealed as follows. The granules' ISO. Roundness and density correlated with raw material (i.e., model drug, diluent, and/or granulation liquid) properties such as density and viscosity. The granules' compressibility parameter a correlated with the granules' Span, and parameter y₀ correlated with the granules' flowability and friability. Compactibility parameters k_a and k_b correlated mainly with granule flowability and density, and parameter b correlated significantly and positively with tablet tensile strength. The compressibility correlated negatively with tablet solid fraction (SF) and friability, while the compactibility correlated positively with tablet disintegration time. Moreover, the rearrangement and elasticity of granules correlated positively with SF and friability, respectively. Overall, this study provides some guides for achieving high-quality tablets via HSWG-T.

Effect of roll compaction pressure on the properties of high drug-loaded piracetam granules and tablets

OBJECTIVE

The aim of this study was to use an alternative granulation technique, solventless roll compaction, and to investigate the effect of the roll compaction pressure on the properties of granules and high-drug-loaded (80%, w/w) immediate release piracetam tablets.Significance. Piracetam commonly manufactured as high drug-loaded tablets by wet granulation with an aqueous binder solution. Due to its high solubility in water, the wet granulation process is largely susceptible to processing methods and can induce the uncontrolled polymorphic transition of piracetam as well as convert it into mono- and di-hydrates.

METHODS

The blends, comprising of piracetam, Kollidon® 30, and Avicel^® PH-101 were roll compacted at 4, 5 and 13 MPa hydraulic pressure and calibrated using an industrial roll compactor. The resultant granules milled and raw piracetam were investigated with DSC. The resultant granules mixed with Ac-Di-Sol^®, Aerosil^® 200 Pharma, and magnesium stearate to prepare tablets using an industrial tablet press at the same compression force and 25, 65, and 100 rpm. The obtained tablets were film coated with an aqueous dispersion of Opadry^® II using a pilot-scale solid-wall pan coater.

RESULTS

Roll compaction pressure influenced the polymorphic composition of piracetam, the granule properties and tablet mixture in relation to morphology, particle size, flowability, bulk and tapped density, as well as tablet hardness, tablet friability, disintegration, and dissolution.

CONCLUSION

This study showed the roll compaction can be successfully used for the preparation of highly water-soluble, highly drug-loaded piracetam film-coated tablets avoiding wet granulation pitfalls.

Influence of Formulation Factors, Process Parameters, and Selected Quality Attributes on Carvedilol Release from Roller-Compacted Hypromellose-Based Matrix Tablets

The importance of roller compaction is recently increasing. This study evaluates the combined effects of formulation factors, process parameters, and selected quality attributes on drug release from roller-compacted hypromellose-based matrix tablets containing carvedilol as a model drug. The influence of selected factors was statistically assessed and good predictive models were developed for various time points of the release profile. The results show that the release profile is mostly affected by the particle size distribution of granules and roll speed. This indicates that the roller compaction process has a major impact on drug release, which is also formulation dependent. A higher d50 and lower d90 value of spatial filtering technique-based particle size distribution results, a lower roll speed, increased hypromellose content, using microcrystalline cellulose as a filler, and higher tablet hardness, resulted in a decrease in the drug release rate. On the other hand, the effect of the roll pressure, size of screen apertures, and d10 values on drug release was insignificant. The significance of the factors was further explained by granule shape, their porosity, and friability evaluation, and by compressibility and compactibility studies of compression mixtures. Additionally, the spatial filtering technique demonstrated to be a promising tool in controlling the roller compaction process.

In-Depth Understanding of Granule Compression Behavior under Variable Raw Material and Processing Conditions

Tablet manufacturing involves the processing of raw materials through several unit operations. Thus, the mitigation of input-induced variability should also consider the downstream processability of intermediary products. The objective of the present work was to study the effect of variable raw materials and processing conditions on the compression properties of granules containing two active pharmaceutical ingredients (APIs) and microcrystalline cellulose. Differences in compressibility and tabletability of granules were highlighted in function of the initial particle size of the first API, granule polydispersity and fragmentation. Moreover, interactions were underlined with the atomizing pressure. Changing the supplier of the second API was efficiently controlled by adapting the binder addition rate and atomizing pressure during granulation, considering the starting crystal size. By fitting mathematical models on the available compression data, the influence of diluent source on granule compactibility and tabletability was identified. These differences resumed to the ease of compaction, tableting capacity and pressure sensitivity index due to variable water binding capacity of microcrystalline cellulose. Building the design space enabled the identification of suitable API types and the appropriate processing conditions (spray rate, atomizing pressure, compression force) required to ensure the desired tableting performance.