In vivo gleno-humeral joint loads during forward flexion and abduction

Finite element analysis and biomechanical study of "sandwich" fixation in the treatment of elderly proximal humerus fractures

Proximal humerus fractures (PHFs) are common in the elderly and usually involve defects in the medial column.The current standard for medial column reconstruction is a lateral locking plate (LLP) in combination with either an intramedullary fibula support or an autogenous fibula graft. However, autogenous fibula graft can lead to additional trauma for patients and allogeneic fibular graft can increase patients' economic burden and pose risks of infection and disease transmission. The primary objective of this study was to introduce and assess a novel "Sandwich" fixation technique and compare its biomechanical properties to the traditional fixation methods for PHFs. In this study, we established finite element models of two different internal fixation methods: LLP-intramedullary reconstruction plate with bone cement (LLP-IRPBC) and LLP-intramedullary fibula segment (LLP-IFS). The biomechanical properties of the two fixation methods were evaluated by applying axial, adduction, abduction, torsional loads and screw extraction tests to the models. These FEA results were subsequently validated through a series of biomechanical experiments. Under various loading conditions such as axial, adduction, abduction, and rotation, the LLP-IRPBC group consistently demonstrated higher structural stiffness and less displacement compared to the LLP-IFS group, regardless of whether the bone was in a normal (Nor) or osteoporotic (Ost) state. Under axial, abduction and torsional loads, the maximum stress on LLPs of LLP-IRPBC group was lower than that of LLP-IFS group, while under adduction load, the maximum stress on LLPs of LLP-IRPBC group was higher than that of LLP-IFS group under Ost condition, and almost the same under Nor condition. The screw-pulling force in the LLP-IRPBC group was 1.85 times greater than that of the LLP-IFS group in Nor conditions and 1.36 times greater in Ost conditions. Importantly, the results of the biomechanical experiments closely mirrored those obtained through FEA, confirming the accuracy and reliability of FEA. The novel "Sandwich" fixation technique appears to offer stable medial support and rotational stability while significantly enhancing the strength of the fixation screws. This innovative approach represents a promising strategy for clinical treatment of PHFs.

Influence of Critical Shoulder Angle and Rotator Cuff Tear Type on Load-Induced Glenohumeral Biomechanics: A Sawbone Simulator Study

Glenohumeral (GH) biomechanics after rotator cuff (RC) tears are not fully understood. The purpose of our study was to determine if the critical shoulder angle (CSA), type of RC tears, and level of weight bearing increase GH translation, instability based on the instability ratio, muscle forces and joint reaction force (JRF), and shifts the center of force (CoF) superiorly. A GH simulator with muscle-mimicking cable systems was used to simulate 30° abduction in the scapular plane. A Sawbone humerus and five specimen-specific scapular anthropometries were used to test six types of RC tears, three weight-bearing loads, and the native and adjusted (to different CSAs) deltoid origin sites. Linear mixed effects models (CSA, RC tear type, and weight bearing) with random effects (specimen and sex) were used to assess differences in GH biomechanics. With increasing CSA, GH translation increased, JRF decreased, and the CoF position was more inferior. RC tears did not significantly alter GH translation but shifted the CoF position superiorly, close to where glenoid erosion occurs in patients with RC tears with secondary osteoarthritis. Weight bearing significantly increased GH translation and JRF. RC and deltoid muscle forces increased with the presence of RC tears and increased weight bearing. The remaining RC muscles of intact tendons compensated for the torn RC tendons but not for the altered CoF position. GH translation remained comparable to shoulders with intact RC. These findings highlight the importance of early detection, clinical management, and targeted rehabilitation strategies for patients with RC tears.

A stemless anatomic shoulder arthroplasty design provides increased cortical medial calcar bone loading in variable bone densities compared to a short stem implant

Background

Several studies have reported proximal bone resorption in stemless and press-fit short-stem humeral implants for anatomic total shoulder arthroplasty. The purpose of this biomechanical study was to evaluate implant and cortical bone micromotion of a cortical rim-supported stemless implant compared to a press-fit short stem implant during cyclic loading and static compression testing.

Methods

Thirty cadaveric humeri were assigned to 3 groups based on a previously performed density analysis, adopting the metaphyseal and epiphyseal and inferior supporting bone densities for multivariate analyses. Implant fixation was performed in stemless implant in low bone density (SL-L, n = 10) or short stem implant in low bone density (Stem-L, n = 10) and in stemless implant in high bone density (SL-H, n = 10). Cyclic loading with 220 N, 520 N, and 820 N over 1000 cycles at 1.5 Hz was performed with a constant valley load of 25 N. Optical recording allowed for spatial implant tracking and quantification of cortical bone deformations in the medial calcar bone region. Implant micromotion was measured as rotational and translational displacement. Load-to-failure testing was performed at a rate of 1.5 mm/s with ultimate load and stiffness measured.

Results

The SL-H group demonstrated significantly reduced implant micromotion compared to both low-density groups (SL-L: P = .014; Stem-L: P = .031). The Stem-L group showed significantly reduced rotational motion and variance in the test results at the 820-N load level compared to the SL-L group (equal variance: P = .012). Implant micromotion and reversible bone deformation were significantly affected by increasing load (P < .001), metaphyseal cancellous (P = .023, P = .013), and inferior supporting bone density (P = .016, P = .023). Absolute cortical bone deformation was significantly increased with stemless implants in lower densities and percentage reversible bone deformation was significantly higher for the SL-H group (21 ± 7%) compared to the Stem-L group (12 ± 6%, P = .017).

Conclusion

A cortical rim-supported stemless implant maintained proximally improved dynamic bone loading in variable bone densities compared to a press-fit short stem implant. Biomechanical time-zero implant micromotion in lower bone densities was comparable between short stem and stemless implants at rehabilitation load levels (220 N, 520 N), but with higher cyclic stability and reduced variability for stemmed implantation at daily peak loads (820 N).

Maximum in-vivo joint contact forces double during active compared to assisted motion in the glenohumeral joint and decline long-term due to rotator cuff pathologies

Rehabilitation programs advocate early passive and assisted motion after rotator cuff repair to induce healing und maintaining range of motion while avoiding excessive strain on the repaired tendons. In-vivo glenohumeral joint contact forces reflect the compressive forces generated by the rotator muscles. In the present study, maximum in-vivo joint contact forces (FresMax) were determined to compare active and assisted execution of a single movement and the long-term development of joint compression forces. FresMax were measured in six patients who received instrumented, telemetric modified anatomical hemi endoprostheses of the shoulder joint between 2006 and 2008. Data were gathered 23 months postoperatively (2006-2010), were analysed and compared with measurements 133 months postoperatively. Additional imaging was obtained as x-rays and ultrasound examination. Data analysis was conducted by synchronizing video tapes and measured force curves. New imaging showed a rupture of the M. supraspinatus and progressive joint degeneration. FresMax nearly doubled during active compared to assisted execution of each of the four chosen movements. Over the course of 133 months post-surgery, the studied movements showed a decrease of active compression force, probably due to a ruptured supraspinatus, resulting in a lower active/assisted ratio. A long term follow up after eleven years, eight out of ten measured movements showed a decrease of FresMax. These results support current rehabilitation protocols recommending early passive and assisted motion to limit activation of the rotator muscles generating compressive forces. Following degeneration of the rotator cuff, active joint contact forces decrease over time.Level of evidence: III.

Time-elapsed microstructural imaging of failure of the reverse shoulder implant

BACKGROUND

Reverse Shoulder Arthroplasties (RSA) have become a primary choice for improving shoulder function and pain. However, the biomechanical failure mechanism of the humeral component is still unclear. The present study reports a novel protocol for microstructural imaging of the entire humerus implant under load before and after fracture.

METHODS

A humerus specimen was obtained from a 75-year-old male donor. An expert surgeon implanted the specimen with a commonly used RSA implant (Aequalis reversed II, Stryker Orthopaedics, USA) and surgical procedure. The physiological glenohumeral contact force that maximized the distal implant migration was selected from a public repository ( orthoload.com ). Imaging and concomitant mechanical testing were performed using a large-volume micro-CT scanner (Nikon XT H 225 ST) and a custom-made compressive stage. Both when intact and once implanted, the specimen was tested under a pre-load and by imposing a constant deformation causing a physiological reaction load (650 N, 10 degrees adducted). The deformation of the implanted specimen was then increased up to fracture, which was identified by a sudden drop of the reaction force, and the specimen was then re-scanned.

RESULTS

The specimen's stiffness decreased from 874 N/mm to 464 N/mm after implantation, producing movements of the bone-implant interface consistent with the implant's long-term stability reported in the literature. The micro-CT images displayed fracture of the tuberosity, caused by a combined compression and circumferential tension, induced by the distal migration of the implant.

CONCLUSION

The developed protocol offers detailed information on implant mechanics under load relative to intact conditions and fracture, providing insights into the failure mechanics of RSA implants. This protocol can be used to inform future implant design and surgical technique improvements.

The influence of rotator cuff tear type and weight bearing on shoulder biomechanics in an ex vivo simulator experiment

Glenohumeral biomechanics after rotator cuff (RC) tears have not been fully elucidated. This study aimed to investigate the muscle compensatory mechanism in weight-bearing shoulders with RC tears and asses the induced pathomechanics (i.e., glenohumeral translation, joint instability, center of force (CoF), joint reaction force). An experimental, glenohumeral simulator with muscle-mimicking cable system was used to simulate 30° scaption motion. Eight fresh-frozen shoulders were prepared and mounted in the simulator. Specimen-specific scapular anthropometry was used to test six RC tear types, with intact RC serving as the control, and three weight-bearing loads, with the non-weight-bearing condition serving as the control. Glenohumeral translation was calculated using instantaneous helical axis. CoF, muscle forces, and joint reaction forces were measured using force sensors integrated into the simulator. Linear mixed effects models (RC tear type and weight-bearing) with random effects (specimen and sex) were used to assess differences in glenohumeral biomechanics. RC tears did not change the glenohumeral translation (p > 0.05) but shifted the CoF superiorly (p ≤ 0.005). Glenohumeral translation and joint reaction forces increased with increasing weight bearing (p < 0.001). RC and deltoid muscle forces increased with the presence of RC tears (p ≤ 0.046) and increased weight bearing (p ≤ 0.042). The synergistic muscles compensated for the torn RC tendons, and the glenohumeral translation remained comparable to that for the intact RC tendons. However, in RC tears, the more superior CoF was close to where glenoid erosion occurs in RC tear patients with secondary osteoarthritis. These findings underscore the importance of early detection and precise management of RC tears.

Scapular morphology variation affects reverse total shoulder arthroplasty biomechanics. A predictive simulation study using statistical and musculoskeletal shoulder models

Reverse total shoulder arthroplasty (RTSA) accounts for over half of shoulder replacement surgeries. At present, the optimal position of RTSA components is unknown. Previous biomechanical studies have investigated the effect of construct placement to quantify mobility, stability and functionality postoperatively. While studies have provided valuable information on construct design and surgical placement, they have not systematically evaluated the importance of scapular morphology on biomechanical outcomes. The aim of this study was to assess the influence of scapular morphology variation on RTSA biomechanics using statistical models, musculoskeletal modeling and predictive simulation. The scapular geometry of a musculoskeletal model was altered across six modes of variation at four levels (±1 and ±3 SD) from a clinically derived statistical shape model. For each model, a standardized virtual surgery was performed to place RTSA components in the same relative position on each model then implemented in 50 predictive simulations of upward and lateral reaching tasks. Results showed morphology affected functional changes in the deltoid moment arms and recruitment for the two tasks. Variation of the anatomy that reduced the efficiency of the deltoids showed increased levels of muscle force production, joint load magnitude and shear. These findings suggest that scapular morphology plays an important role in postoperative biomechanical function of the shoulder with an implanted RTSA. Furthermore a "one-size-fits-all" approach for construct surgical placement may lead to suboptimal patient outcomes across a clinical population. Patient glenoid as well as scapular anatomy may need to be carefully considered when planning RTSA to optimize postoperative success.

Glenohumeral joint force prediction with deep learning

Deep learning models (DLM) are efficient replacements for computationally intensive optimization techniques. Musculoskeletal models (MSM) typically involve resource-intensive optimization processes for determining joint and muscle forces. Consequently, DLM could predict MSM results and reduce computational costs. Within the total shoulder arthroplasty (TSA) domain, the glenohumeral joint force represents a critical MSM outcome as it can influence joint function, joint stability, and implant durability. Here, we aimed to employ deep learning techniques to predict both the magnitude and direction of the glenohumeral joint force. To achieve this, 959 virtual subjects were generated using the Markov-Chain Monte-Carlo method, providing patient-specific parameters from an existing clinical registry. A DLM was constructed to predict the glenohumeral joint force components within the scapula coordinate system for the generated subjects with a coefficient of determination of 0.97, 0.98, and 0.98 for the three components of the glenohumeral joint force. The corresponding mean absolute errors were 11.1, 12.2, and 15.0 N, which were about 2% of the maximum glenohumeral joint force. In conclusion, DLM maintains a comparable level of reliability in glenohumeral joint force estimation with MSM, while drastically reducing the computational costs.

Biomechanical testing of osteosynthetic locking plates for proximal humeral shaft fractures - a systematic literature review

Proximal humeral shaft fractures can be treated with helically deformed bone plates to reduce the risk of iatrogenic nerve lesion. Controversially to this common surgical technique that was first established in 1999, no biomechanical investigation on humeral helical plating is recorded by other reviews, which focus on proximal fractures exclusively. Does an additional scope for shaft fractures reveal findings of helical testing? The present systematic literature review was performed based on guidelines by Kitchenham et al. to systematically search and synthesize literature regarding biomechanical testing of osteosynthetic systems for proximal humeral shaft fractures. Therefore, a systematic approach to search and screen literature was defined beforehand and applied on the findings of the database PubMed®. Synthesized information of the included literature was categorized, summarized and analyzed via descriptive statistics. Out of 192 findings, 22 publications were included for qualitative synthesis. A wide range of different test methods was identified, leading to a suboptimal comparability of specific results between studies. Overall, 54 biomechanical test scenarios were identified and compared. Physiological based boundary conditions (PB-BC) were referenced in 7 publications only. One study of testing straight and helical dynamic compression plates without PB-BCs was identified, showing significant differences under compressional loading. The absence of test standards of specific fields like humeral fractures lead to a high variance in biomechanical testing of osteosynthetic locking plates for proximal humeral shaft fractures. Physiological approaches offer realistic test scenarios but need to be uniformed for enhanced comparability between studies. The impact of helically deformed locking plates under PB-BC was not identified in literature.

Effect of subscapularis repair on joint contact forces based on degree of posterior-superior rotator cuff tear severity in reverse shoulder arthroplasty

Massive irreparable rotator cuff tears (RCTs) affect the clinical outcomes of reverse shoulder arthroplasty (RSA). However, the effects of subscapularis repair on the outcomes of RSA, based on the degree of posterior-superior RCTs, are unclear. This study aimed to examine the effect of subscapularis repair on three-dimensional joint contact forces (JCFs) based on the degree of posterior-superior RCT severity in RSA. Ten human in vivo experimental data were used as input to the musculoskeletal model. A six-degrees-of-freedom (DOF) anatomical shoulder model was developed and validated against three-dimensional JCFs. The 6-DOF musculoskeletal shoulder model of RSA was then developed by importing the reverse shoulder implant into the validated anatomical shoulder model. Based on the various types of posterior-superior RCT severity, inverse dynamic simulations of subscapularis-torn and subscapularis-repaired models of RSA were performed: from isolated supraspinatus tears to partial or massive tears of the infraspinatus and teres minor. The intact rotator cuff model of RSA was also simulated for comparison with the different types of models. Our results showed that the more posterior-superior RCTs progressed in RSA, the more superior JCFs were observed at 90°, 105°, and 120° abduction in the subscapularis-torn model. However, subscapularis repair decreased the superior JCF at those angles sufficiently. In addition, the teres minor muscle-tendon force increased as infraspinatus bundle tears progressed in both the subscapularis-torn and -repaired models, in order to compensate for the reduced force during abduction. However, the teres minor muscle-tendon force was not as high as that of the infraspinatus muscle-tendon, which could result in muscle force imbalance between repaired subscapularis and teres minor. Therefore, our results suggest that repairing the subscapularis and the repairable infraspinatus during RSA can improve glenohumeral joint stability in the superior-inferior direction by restoring muscle force balance between the anterior cuff (i.e., subscapularis) and posterior cuff (i.e., infraspinatus and teres minor). The findings of this study can help clinician decide whether to repair the rotator cuff during RSA to enhance joint stability.

Design of a reverse shoulder implant to measure shoulder stiffness during implant component positioning

To avoid dislocation of the shoulder joint after reverse total shoulder arthroplasty, it is important to achieve sufficient shoulder stability when placing the implant components during surgery. One parameter for assessing shoulder stability can be shoulder stiffness. The aim of this research was to develop a temporary reverse shoulder implant prototype that would allow intraoperative measurement of shoulder stiffness while varying the position of the implant components. Joint angle and torque measurement techniques were developed to determine shoulder stiffness. Hall sensors were used to measure the joint angles by converting the magnetic flux densities into angles. The accuracy of the joint angle measurements was tested using a test bench. Torques were determined by using thin-film pressure sensors. Various mechanical mechanisms for variable positioning of the implant components were integrated into the prototype. The results of the joint angle measurements showed measurement errors of less than 5° in a deflection range of ±15° adduction/abduction combined with ±45° flexion/extension. The proposed design provides a first approach for intra-operative assessment of shoulder stiffness. The findings can be used as a technological basis for further developments.

Implications of humeral short-stem diametral sizing on implant stability

Background

Shoulder arthroplasty humeral stem design has evolved to include various shapes, coatings, lengths, sizes, and fixation methods. While necessary to accommodate patient anatomy characteristics, this creates a surgical paradox of choice. The relationship between the surgeon's selection of short-stem implant size and construct stiffness, resistance to subsidence and micromotion has not been assessed.

Methods

Eight paired cadaveric humeri were reconstructed with surgeon-selected (SS) and 2-mm diametrically larger (SS+2) short-stemmed press-fit implants. Each reconstruction was subjected to 2000 cycles of 90° forward flexion loading, and stem subsidence and micromotion were measured using optical tracking. Compressive stiffness of the stem-bone reconstruction was then assessed by applying a load in-line with the stem axis that resulted in 5 mm of stem subsidence.

Results

Increasing stem size by 2 mm resulted in the construct stiffness more than doubling compared to SS stems (-741 ± 243 N/mm vs. -334 ± 120 N/mm; P = .003; power = 0.971). These larger stems also subsided significantly less than their SS counterparts (SS: 1.2 ± 0.6 mm; SS+2: 0.5 ± 0.5 mm; P = .029; power = 0.66), though there were no significant changes in micromotion (SS: 169 ± 59 μm; SS+2: 187 ± 52 μm; P = .506; power = 0.094).

Conclusions

The results of this study highlight the importance of proper short-stem sizing, as a relatively small 2 mm increase in diametral size was observed to significantly impact construct stiffness, which could increase the risk of stress shielding and implant loosening. Future work should focus on developing tools that objectively quantify bone quality and aid surgeons in selecting the appropriate size short-stem humeral implants for a particular patient.

Assessment of micromotion at the bone-bone interface after coracoid and scapular-spine bone-block augmentation for the reconstruction of critical anterior glenoid bone loss-a biomechanical cadaver study

BACKGROUND

Glenoid bone loss is among the most important risk factors for recurrent anterior shoulder instability, and a bony reconstruction is recommended in cases of critical bone loss (> 15%). The commonly used surgical techniques, including coracoid transfer, are associated with considerable complications. The aim of this study was to assess the motion at the glenoid-bone-block interface after coracoid and spina-scapula bone-block reconstruction of the anterior glenoid.

METHODS

Twelve cadaveric shoulders were tested. A 20% bone defect of the anterior glenoid was created, and the specimens were randomly assigned for glenoid augmentation using a coracoid bone block (n = 6) or a scapular spine bone block (n = 6). The glenoid-bone interface was cyclically loaded for 5000 cycles with a force of 170 N. The micromotion was tracked using an optical measurement system (GOM ARMIS) and was evaluated with the GOM Correlate Pro software.

RESULTS

The most dominant motion component was medial irreversible displacement for the spina-scapula (1.87 mm; SD: 1.11 mm) and coracoid bone blocks (0.91 mm; SD: 0.29 mm) (n.s.). The most medial irreversible displacement took place during the first nine cycles. The inferior reversible displacement was significantly greater for spina-scapula bone blocks (0.28 mm, SD: 0.16 mm) compared to coracoid bone blocks (0.06 mm, SD: 0.10 mm) (p = 0.02).

CONCLUSIONS

The medial irreversible displacement is the dominant motion component in a bone-block reconstruction after a critical bone loss of the anterior glenoid. The spina-scapula and coracoid bone blocks are comparable in terms of primary stability and extent of motion. Thus, spina-scapula bone blocks may serve as alternatives in bony glenoid reconstruction from a biomechanical point of view.

Latarjet's muscular alterations increase glenohumeral joint stability: A theoretical study

The surgical Latarjet procedure aims to stabilise the glenohumeral joint following anterior dislocations. Despite restoring joint stability, the procedure introduces alterations of muscle paths which likely modify the shoulder dynamics. Currently, these altered muscular functions and their implications are unclear. Hence, this work aims to predict changes in muscle lever arms, muscle and joint forces following a Latarjet procedure by using a computational approach. Planar shoulder movements of ten participants were experimentally assessed. A validated upper-limb musculoskeletal model was utilised in two configurations, i.e., a baseline model, simulating normal joint, and a Latarjet model simulating its related muscular alterations. Muscle lever arms and differences in muscle and joint forces between models were derived from the experimental marker data and static optimisation technique. Lever arms of most altered muscles, hence their role, were substantially changed after Latarjet. Altered muscle forces varied by up to 15% of the body weight. Total glenohumeral joint force increased by up to 14% of the body weight after Latarjet, mostly due to increase in compression force. Our simulation indicated that the Latarjet muscular alterations lead to changes in the muscular recruitment and contribute to the stability of the glenohumeral joint by increasing compression force during planar motions.

A Validated Open-Source Shoulder Finite Element Model and Investigation of the Effect of Analysis Precision

Understanding the loads and stresses on different tissues within the shoulder complex is crucial for preventing joint injury and developing shoulder implants. Finite element (FE) models of the shoulder joint can be helpful in describing these forces and the biomechanics of the joint. Currently, there are no validated FE models of the intact shoulder available in the public domain. This study aimed to develop and validate a shoulder FE model, then make the model available to the orthopaedic research community. Publicly available medical images of the Visible Human Project male subject's right shoulder were used to generate the model geometry. Material properties from the literature were applied to the different tissues. The model simulated abduction in the scapular plane. Simulated glenohumeral (GH) contact force was compared to in vivo data from the literature, then further compared to other in vitro experimental studies. Output variable results were within one standard deviation of the mean in vivo experimental values of the GH contact force in 0°, 10°, 20°, 30°, and 45° of abduction. Furthermore, a comparison among different analysis precision in the Abaqus/Explicit platform was made. The complete shoulder model is available for download at github.com/OSEL-DAM/ShoulderFiniteElementModel.

Reverse total shoulder glenoid component inclination affects glenohumeral kinetics during abduction: a cadaveric study

BACKGROUND

Optimal implant placement in reverse total shoulder arthroplasty (rTSA) remains controversial. Specifically, the optimal glenoid inclination is unknown. Therefore, a cadaveric shoulder simulator with 3-dimentional human motion specific to rTSA was used to study joint contact and muscle forces as a function of glenoid component inclination.

METHODS

Eight human cadaver shoulders were tested before and after rTSA implantation. Scapular plane abduction kinematics from control subjects and those with rTSA drove a cadaveric shoulder simulator with 3-dimentional scapulothoracic and glenohumeral motion. Glenoid inclination varied from -20° to +20°. Outputs included compression, superior-inferior (S/I) shear, and anterior-posterior shear forces from a 6° of freedom load cell in the joint, and deltoid and rotator cuff muscle forces. Data were evaluated with statistical parametric mapping and t-tests.

RESULTS

Inferior glenoid inclination (-) reduced S/I shear by up to 125% relative to superior inclination, with similar compression to the neutral condition (0°). Superior inclinations (+) increased the S/I shear force by approximately the same magnitude, yet decreased compression by 25% in the most superior inclination (+20°). There were few differences in deltoid or rotator cuff forces due to inclination. Only the middle deltoid decreased by approximately 7% for the most inferior inclination (-20°). Compared with native shoulders, the neutral (0°) rTSA inclination showed reduced forces of 30%-75% in the anterior deltoid and a trend toward decreased forces in the middle deltoid. Force demands on the rotator cuff varied as a function of elevation, with a trend toward increased forces in rTSA at peak glenohumeral elevation.

CONCLUSIONS

Inferior inclination reduces superior shear forces, without influencing compression. Superior inclination increased S/I shear, while decreasing compression, which may be a source of component loosening and joint instability after rTSA. Inferior inclination of the rTSA glenoid may reduce the likelihood of glenoid loosening by reducing the magnitude of cyclic shear and compressive loading during arm elevation activities, although this may be altered by specific-subject body habitus and motion. These factors are especially important in revision rTSA or glenoid bone grafting where there is already a 3-fold increase in glenoid baseplate loosening vs. primary rTSA.

Anatomic total shoulder glenoid component inclination affects glenohumeral kinetics during abduction: a cadaveric study

BACKGROUND

Although typically favorable in outcome, anatomic total shoulder arthroplasty (aTSA) can require long-term revision. The most common cause for revision is glenoid loosening, which may result from eccentric cyclic forces and joint translations. "Rocking" of the glenoid component may be exacerbated by the joint geometry, such as glenoid inclination and version. Restoration of premorbid glenoid inclination may be preferable, although laboratory and computational models indicate that both superior inclination and inferior inclination have benefits. This discrepancy may arise because previous studies were limited by a lack of physiological conditions to test inclination. Therefore, a cadaveric shoulder simulator with 3-dimensional human motion was used to study joint contact and muscle forces with isolated changes in glenoid inclination.

METHODS

Eight human cadaveric shoulders were tested before and after aTSA. Scapular-plane abduction kinematics from human subjects were used to drive a cadaveric shoulder simulator with 3-dimensional scapulothoracic and glenohumeral motion. Glenoid inclination was varied from -10° to +20°, whereas compressive, superior-inferior shear, and anterior-posterior shear forces were collected with a 6-df load cell during motion. Outputs also included muscle forces of the deltoid and rotator cuff. Data were evaluated with statistical parametric mapping repeated-measures analysis of variance and t tests.

RESULTS

Inferior glenoid inclination (-10°) reduced both compressive and superior-inferior shear forces vs. neutral 0° inclination by up to 40%, and even more when compared with superior inclination (P < .001). Superior inclinations (+10° and +20°) tended to increase deltoid and rotator cuff forces vs. neutral 0° inclination or inferior inclination, on the order of 20%-40% (P ≤ .045). All force metrics except anterior-posterior shear were lowest for inferior inclination. Most aTSA muscle forces for neutral 0° inclination were not significantly different from native shoulders and decreased 45% and 15% in the posterior deltoid and supraspinatus, respectively (P ≤ .003). Joint translations were similar to prior reports in aTSA patients and did not differ between any inclinations or compared with native shoulders. Joint reaction forces were similar to those observed in human subjects with instrumented aTSA implants, providing confidence in the relative magnitude of our results.

CONCLUSIONS

Inferior inclination reduces overall forces in the shoulder. Superior inclinations increase the muscle effort required for the shoulder to achieve similar motion, thus increasing the forces exerted on the glenoid component. These results suggest that a preference toward aTSA glenoid components in inferior inclination may reduce the likelihood of glenoid loosening by reducing excessive muscle and joint contact forces.

Temporary Protective Shoulder Implants for Revision Surgery with Bone Glenoid Grafting

This article describes the development of a temporary protective glenoid prosthesis placed between the augmentation and humeral head prosthesis during the healing phase of shoulder prosthesis revision with necessary reconstruction of the bony structure of the glenoid. The glenoid protection prosthesis ensures the fixation of the augmentation material and protects the screws from contact with the metallic humeral head prosthesis. Another approach of the development is a reduction of the resorption of the augmentation by targeted mechanical stimulation of the tissue. The aim should be to achieve significantly improved conditions for the implantation of a new glenoid component at the end of the healing phase of the augmentation material in comparison to the current standard method. The development of the protective prosthesis was carried out according to specific needs and includes the collection of requirements and boundary conditions, the design and technical detailing of the implant, the verification of the development results as well as the validation of the design. For the verification, FEM simulations (Finite Element Analysis) were performed to estimate the mechanical stability in advance. Mechanical tests to confirm the stability and abrasion behavior have been carried out and confirm the suitability of the protective implant. The result of the present work is the detailed technical design of two variants of a glenoid protective prosthesis "GlenoProtect" for use in revision procedures on shoulder joints-with large-volume defects on the glenoid-treated by arthroplasty and the necessity of augmenting the glenoid, including a description of the surgical procedure for implantation.

The addition of cerclage wiring does not improve proximal bicortical fixation of locking plates for Type C periprosthetic fractures in synthetic humeri

BACKGROUND

Treatment of proximal humerus periprosthetic fractures is challenging. It remains difficult to achieve robust fixation of the proximal fragment to the locking plate using cerclage wiring and/or unicortical screws. Use of polyaxial tangentially directed bicortical locking screws increases screw purchase, but it is unclear if this option provides robust fixation. This biomechanical study compares fixation of constructs using cerclage wires, bicortical locking screws, and a hybrid method utilizing both methods.

METHODS

Uncemented humeral stems were implanted into synthetic humeri and Type C periprosthetic fractures were simulated with a 1 cm transverse osteotomy. Distal ends of locking plates were secured with bicortical non-locking screws. The proximal ends were supported by either isolated cerclage wires, polyaxial locking screws, or a hybrid combination of both (n = 6 for each group). A universal test frame was used for non-destructive torsion and cyclic axial compression tests. 3-D motion tracking was employed to determine stiffnesses and relative interfragmentary motions.

FINDINGS

Isolated screw constructs showed significantly increased resistance against torsional movement, bending, and shear, (p < 0.05) in comparison to cerclage constructs. The hybrid construct provided no significant changes in stability over the isolated screw construct.

INTERPRETATION

Addition of cerclage wires in this synthetic bone model of Type C periprosthetic humerus fractures did not add significant stability to proximal bicortical locking plate fixation. Considering risks of tissue stripping and nerve injury, usage of cerclage wires in a similar clinical setting should be chosen carefully, especially when bicortical fixation around the prosthetic stem can be achieved.

Locking Plates With Computationally Enhanced Screw Trajectories Provide Superior Biomechanical Fixation Stability of Complex Proximal Humerus Fractures

Joint-preserving surgical treatment of complex unstable proximal humerus fractures remains challenging, with high failure rates even following state-of-the-art locked plating. Enhancement of implants could help improve outcomes. By overcoming limitations of conventional biomechanical testing, finite element (FE) analysis enables design optimization but requires stringent validation. This study aimed to computationally enhance the design of an existing locking plate to provide superior fixation stability and evaluate the benefit experimentally in a matched-pair fashion. Further aims were the evaluation of instrumentation accuracy and its potential influence on the specimen-specific predictive ability of FE. Screw trajectories of an existing commercial plate were adjusted to reduce the predicted cyclic cut-out failure risk and define the enhanced (EH) implant design based on results of a previous parametric FE study using 19 left proximal humerus models (Set A). Superiority of EH versus the original (OG) design was tested using nine pairs of human proximal humeri (N = 18, Set B). Specimen-specific CT-based virtual preoperative planning defined osteotomies replicating a complex 3-part fracture and fixation with a locking plate using six screws. Bone specimens were prepared, osteotomized and instrumented according to the preoperative plan via a standardized procedure utilizing 3D-printed guides. Cut-out failure of OG and EH implant designs was compared in paired groups with both FE analysis and cyclic biomechanical testing. The computationally enhanced implant configuration achieved significantly more cycles to cut-out failure compared to the standard OG design (p &lt; 0.01), confirming the significantly lower peri-implant bone strain predicted by FE for the EH versus OG groups (p &lt; 0.001). The magnitude of instrumentation inaccuracies was small but had a significant effect on the predicted failure risk (p &lt; 0.01). The sample-specific FE predictions strongly correlated with the experimental results (R2 = 0.70) when incorporating instrumentation inaccuracies. These findings demonstrate the power and validity of FE simulations in improving implant designs towards superior fixation stability of proximal humerus fractures. Computational optimization could be performed involving further implant features and help decrease failure rates. The results underline the importance of accurate surgical execution of implant fixations and the need for high consistency in validation studies.

Finite element analysis to predict short and medium-term performance of the anatomical Comprehensive® Total Shoulder System

BACKGROUND

The number of Total Shoulder Arthroplasties (TSA) has increased in these last years with significant increase of clinical success. However, glenoid component loosening remains the most common cause of failure.

OBJECTIVE

In this study we evaluated the critical conditions to predict short and medium-term performance of the uncemented anatomical Comprehensive® Total Shoulder System using a finite element model that was validated experimentally.

METHODS

The finite element models of an implanted shoulder analysed included total shoulder components with pegs. The models were simulated in 3 phases of adduction: 45°, 60° and 90° to determine the most critical situation. Two different bone-implant fixation conditions were considered: post-surgery and medium term (2 years).

RESULTS

These show that the critical condition is for the shoulder in 90° adduction were the highest contact stress (70 MPa) was observed in the glenoid component. Relatively to the interface implant-bone strains, the maximum (-16000 µε) was observed for the short-term in the lateral region of the humerus. The highest micromotions were observed in the central fixation post of the glenoid component, ranging from 20 to 25 µm, and 325 µm in the lateral plane of the humeral component.

CONCLUSION

The predicted results are in accordance with clinical studies published and micromotions of the humeral component can be used to predict loosening and to differentiate shoulder implant designs.

Effect of two types of shoulder prosthesis on the muscle forces using a generic multibody model for different arm motions

Background

This study aims to analyze the effects of a novel dual-bearing shoulder prosthesis and a conventional reverse shoulder prosthesis on the deltoid and rotator cuff muscle forces for four different arm motions. The dual-bearing prosthesis is a glenoid-sparing joint replacement with a moving center of rotation. It has been developed to treat rotator cuff arthropathy, providing an increased post-operative functionality.

Methods

A three-dimensional musculoskeletal OpenSim® model of an upper body, incorporating a natural gleno-humeral joint and a scapula-thoracic joint developed by Blana et al. (J Biomech 41: 1714-1721, 2008), was used as a reference for the natural shoulder. It was modified by integrating first a novel dual-bearing prosthesis, and second, a reverse shoulder prosthesis into the shoulder joint complex. Four different arm motions, namely abduction, scaption, internal and external rotation, were simulated using an inverse kinematics approach. For each of the three models, shoulder muscle forces and joint reaction forces were calculated with a 2 kg weight in the hand.

Results

In general, the maximal shoulder muscle force and joint reaction force values were in a similar range for both prosthesis models during all four motions. The maximal deltoid muscle forces in the model with the dual-bearing prosthesis were 18% lower for abduction and 3% higher for scaption compared to the natural shoulder. The maximal rotator cuff muscle forces in the model with the dual-bearing prosthesis were 36% lower for abduction and 1% higher for scaption compared to the natural shoulder. Although the maximal deltoid muscle forces in the model with the dual-bearing prosthesis in internal and external rotation were 52% and 64% higher, respectively, compared to the natural shoulder, the maximal rotator cuff muscle forces were 27% lower in both motions.

Conclusion

The study shows that the dual-bearing shoulder prosthesis is a feasible option for patients with rotator cuff tear and has a strong potential to be used as secondary as well as primary joint replacement. The study also demonstrates that computer simulations can help to guide the continued optimization of this particular design concept for successful clinical outcomes.

Can neck fractures in proximal humeri be predicted by CT-based FEA?

BACKGROUND

Proximal humeri fractures at anatomical and surgical neck (∼5% and ∼50% incidence respectively) are frequent in elderly population. Yet, neither in-vitro experiments nor CT-based finite element analyses (CTFEA) have investigated these in depth. Herein we enhance (Dahan et al., 2019) (addressing anatomical neck fractures) by more experiments and specimens, accounting for surgical neck fractures and explore CTFEA's prediction of humeri mechanical response and yield force.

METHODS

Four fresh frozen human humeri were tested in a new experimental configuration inducing surgical neck fractures. Digital image correlation (DIC) provided strains and displacements on humeri surfaces and used to validate CTFEA predictions. CTFEA were enhanced herein to improve the accuracy at the proximal neck: A cortical bone mapping (CBM) algorithm was implemented to overcome insufficient scanning resolution, and a new trabecular material mapping was investigated.

RESULTS

The new experimental setting induced impacted surgical neck fractures in all humeri. Excellent DIC to CTFEA correlation in strains was obtained at the shaft (slope 0.984, R²=0.99) and a fair agreement (slope 0.807, R²=0.73) at the neck. CBM algorithm had worsened the correlation, whereas the new material mapping had a negligible influence. Yield loads predictions improved considerably when trabecular yielding (maximum principal strain criterion) was considered instead of surface cortical yielding.

DISCUSSION

CTFEA well predicts strains on the shaft and reasonably well on the neck. This enhances former conclusions by past studies conducted using SGs, now also evident by DIC. Yield load prediction for surgical neck fractures (involving crushing of trabecular bone) is predicted better by trabecular failure laws rather than cortex ones. Further FEA studies using trabecular orthotropic constitutive models and failure laws are warrant.

Influence of rotator cuff integrity on loading and kinematics before and after reverse shoulder arthroplasty

Reverse Shoulder Arthroplasty has become a very common procedure for shoulder joint replacement, even for scenarios where an anatomical reconstruction would traditionally be used. Our hypothesis is that implanting a reverse prosthesis with a functional rotator cuff may lead to higher joint reaction force (JRF) and have a negative impact on the prosthesis. Available motion capture data during anterior flexion was input to a finite-element musculoskeletal shoulder model, and muscle activations were computed using inverse dynamics. Simulations were carried out for the intact joint as well as for various types of rotator cuff tears: superior (supraspinatus), superior-anterior (supraspinatus and subscapularis), and superior-posterior (supraspinatus, infraspinatus and teres minor). Each rotator cuff tear condition was repeated after shifting the humerus and the glenohumeral joint center of rotation to represent the effect of a reverse prosthesis. Changes in compressive, shear, and total JRF were analyzed. The model compared favorably to in vivo JRF measurements, and existing clinical and biomechanical knowledge. Implanting a reverse prosthesis with a functional rotator cuff or with an isolated supraspinatus tear led to more than 2 times higher compressive JRF than with massive rotator cuff tears (superior-anterior or superior-posterior), while the shear force remained comparable. The total JRF increased more than 1.5 times. While a lower shear to compressive ratio may reduce the risk of glenosphere loosening, higher JRF might increase the risk for other failure modes such as fracture or polyethylene wear of the reverse prosthesis.

Micromachined Tactile Sensor Array for RTSA

This work presents a polymer-based tactile capacitive sensor capable of measuring joint reaction forces of reverse total shoulder arthroplasty (RTSA). The capacitive sensor contains a polydimethylsiloxane (PDMS) dielectric layer with an array of electrodes. The sensor was designed in such a way that four components of glenohumeral contact forces can be quantified to help ensure proper soft tissue tensioning during the procedure. Fabricated using soft lithography, the sensor has a loading time of approximately 400 ms when a 14.13 kPa load is applied and has a sensitivity of 1.24 × 10-3 pF/kPa at a load of 1649 kPa. A replica RTSA prothesis was 3D printed, and the sensor was mounted inside the humeral cap. Four static right shoulder positions were tested, and the results provided an intuitive graphical description of the pressure distribution across four quadrants of the glenohumeral joint contact surface. It may help clinicians choose a right implant size and offset that best fit a patient's anatomy and reduce postoperative biomechanical complications such as dislocation and stress fracture of the scapula.

A Matlab toolbox for scaled-generic modeling of shoulder and elbow

There still remains a barrier ahead of widespread clinical applications of upper extremity musculoskeletal models. This study is a step toward lifting this barrier for a shoulder musculoskeletal model by enhancing its realism and facilitating its applications. To this end, two main improvements are considered. First, the elbow and the muscle groups spanning the elbow are included in the model. Second, scaling routines are developed that scale model's bone segment inertial properties, skeletal morphologies, and muscles architectures according to a specific subject. The model is also presented as a Matlab toolbox with a graphical user interface to exempt its users from further programming. We evaluated effects of anthropometric parameters, including subject's gender, height, weight, glenoid inclination, and degenerations of rotator cuff muscles on the glenohumeral joint reaction force (JRF) predictions. An arm abduction motion in the scapula plane is simulated while each of the parameters is independently varied. The results indeed illustrate the effect of anthropometric parameters and provide JRF predictions with less than 13% difference compared to in vivo studies. The developed Matlab toolbox could be populated with pre/post operative patients of total shoulder arthroplasty to answer clinical questions regarding treatments of glenohumeral joint osteoarthritis.

Biomechanics of anatomic and reverse shoulder arthroplasty

The biomechanics of the shoulder relies on careful balancing between stability and mobility. A thorough understanding of normal and degenerative shoulder anatomy is necessary, as the goal of anatomic total shoulder arthroplasty is to reproduce premorbid shoulder kinematics.With reported joint reaction forces up to 2.4 times bodyweight, failure to restore anatomy and therefore provide a stable fulcrum will result in early implant failure secondary to glenoid loosening.The high variability of proximal humeral anatomy can be addressed with modular stems or stemless humeral components. The development of three-dimensional planning has led to a better understanding of the complex nature of glenoid bone deformity in eccentric osteoarthritis.The treatment of cuff tear arthropathy patients was revolutionized by the arrival of Grammont's reverse shoulder arthroplasty. The initial design medialized the centre of rotation and distalized the humerus, allowing up to a 42% increase in the deltoid moment arm.More modern reverse designs have maintained the element of restored stability but sought a more anatomic postoperative position to minimize complications and maximize rotational range of motion. Cite this article: EFORT Open Rev 2021;6:918-931. DOI: 10.1302/2058-5241.6.210014.

Finite element modelling and experimental validation of a total implanted shoulder joint

Background Replicating a total shoulder arthroplasty in laboratory is a difficult task due to complex geometry of the structures and degrees of freedom of the joint. Implanted joint shoulders have been investigated using numerical tools, but models developed lack of experimental validation. The objective of this study was to develop a finite element model that replicated correctly an experimental simulator of an implanted joint shoulder based on the comparison of measured and calculated strains. The methods used include a non-cemented Anatomical Comprehensive© Total Shoulder System that was implanted in 4^th generation composite bones. The finite element model designed replicates adequately the experimental model. Both models included the most important muscles of shoulder abduction and the same boundary conditions (loads, fixation, and interface conditions). Strain gauge rosettes were used to measure strain responses on the shoulder in 90° abduction. The results of linear regression analysis between numerical and experimental results present a high correlation coefficient of 0.945 and a root-mean-square-error of 35 µε, suggesting adequate agreement between the experimental and the numerical models. Small strains were obtained and changes in load distribution from posterior to anterior region were observed. As conclusion we can say that the experiments allowed good replication of the finite element model, and the use of strain gauges is suitable for numerical-experimental validation of bone joints.

Effect of Rotator Cuff Deficiencies on Muscle Forces and Glenohumeral Contact Force After Anatomic Total Shoulder Arthroplasty Using Musculoskeletal Multibody Dynamics Simulation

Anatomic total shoulder arthroplasty (ATSA) is widely used to treat the diseases of the glenohumeral (GH) joint. However, the incidence of rotator cuff tears after ATSA increases during follow-up. The effects of rotator cuff deficiencies after ATSA on the biomechanics of the GH joint are to be investigated. In this study, a musculoskeletal multibody dynamics model of ATSA was established using a force-dependent kinematics (FDK) method. The biomechanical effects were predicted during arm abduction under different rotator cuff deficiencies. The deltoid forces were increased under the rotator cuff deficiencies, the maximum deltoid forces were increased by 36% under the subscapularis deficiency and by 53% under the supraspinatus, infraspinatus, subscapularis, and teres minor deficiencies. The maximum GH contact forces were decreased by 11.3% under supraspinatus and infraspinatus deficiencies but increased by 24.8% under subscapularis deficiency. The maximum subscapularis force was decreased by 17% under only infraspinatus tear during arm abduction. The results suggested that the changes in the biomechanics of the GH joint induced by rotator cuff deficiencies after ATSA increase the deltoid muscle energy expenditure and joint instability, which result in postoperative less satisfactory clinical outcomes. The changes in rotator cuff muscle forces deserve more attention for understanding the evolution of rotator cuff tear after ATSA.

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

The shoulder is one of the human body's most complex joint systems, with motion occurring through the coordinated actions of four individual joints, multiple ligaments, and approximately 20 muscles. Unfortunately, shoulder pathologies (e.g., rotator cuff tears, joint dislocations, arthritis) are common, resulting in substantial pain, disability, and decreased quality of life. The specific etiology for many of these pathologic conditions is not fully understood, but it is generally accepted that shoulder pathology is often associated with altered joint motion. Unfortunately, measuring shoulder motion with the necessary level of accuracy to investigate motion-based hypotheses is not trivial. However, radiographic-based motion measurement techniques have provided the advancement necessary to investigate motion-based hypotheses and provide a mechanistic understanding of shoulder function. Thus, the purpose of this article is to describe the approaches for measuring shoulder motion using a custom biplanar videoradiography system. The specific objectives of this article are to describe the protocols to acquire biplanar videoradiographic images of the shoulder complex, acquire CT scans, develop 3D bone models, locate anatomical landmarks, track the position and orientation of the humerus, scapula, and torso from the biplanar radiographic images, and calculate the kinematic outcome measures. In addition, the article will describe special considerations unique to the shoulder when measuring joint kinematics using this approach.

Overdrilling increases the risk of screw perforation in locked plating of complex proximal humeral fractures - A biomechanical cadaveric study

Locked plating of proximal humerus fractures (PHF) is associated with high failure rates (15-37%). Secondary screw perforation is a prominent mode of failure for PHF and typically requires reoperation. The anatomical fracture reduction is an essential factor to prevent fixation failure. However, recent studies indicate that the risk of secondary screw perforation may increase if the articular surface is perforated during predrilling of the screw boreholes (overdrilling). This study aimed to determine whether overdrilling increases the risk of secondary screw perforation in unstable PHF. Nine pairs of human cadaveric proximal humeri were osteotomized to simulate a malreduced and highly unstable 3-part fracture (AO/OTA 11 B1.1), followed by their assignment to two study groups for overdrilling or accurate predrilling in paired design, and fixation with a locking plate. Overdrilling was defined by drilling the calcar screw's boreholes through the articular surface. All humeri were cyclically loaded to screw perforation failure. Number of cycles to initial screw loosening and final perforation failure were analysed. The accurately predrilled group revealed a significantly higher number of cycles to both initial screw loosening (p < 0.01) and final screw perforation failure (p = 0.02), compared to the overdrilled one. This is the first study reporting that drilling to the correct depth significantly increases endurance until screw perforation failure during cyclic loading after locked plating in a highly unstable PHF model. Prevention of overdrilling the boreholes could help reduce failure rates of locked plating. Future work should investigate the prevalence and consequences of overdrilling in clinics.

Glenoid concavity has a higher impact on shoulder stability than the size of a bony defect

PURPOSE

Surgical treatment of shoulder instability caused by anterior glenoid bone loss is based on a critical threshold of the defect size. Recent studies indicate that the glenoid concavity is essential for glenohumeral stability. However, biomechanical proof of this principle is lacking. The aim of this study was to evaluate whether glenoid concavity allows a more precise assessment of glenohumeral stability than the defect size alone.

METHODS

The stability ratio (SR) is a biomechanical estimate of glenohumeral stability. It is defined as the maximum dislocating force the joint can resist related to a medial compression force. This ratio was determined for 17 human cadaveric glenoids in a robotic test setup depending on osteochondral concavity and anterior defect size. Bony defects were created gradually, and a 3D measuring arm was used for morphometric measurements. The influence of defect size and concavity on the SR was examined using linear models. In addition, the morphometrical-based bony shoulder stability ratio (BSSR) was evaluated to prove its suitability for estimation of glenohumeral stability independent of defect size.

RESULTS

Glenoid concavity is a significant predictor for the SR, while the defect size provides minor informative value. The linear model featured a high goodness of fit with a determination coefficient of R² = 0.98, indicating that 98% of the SR is predictable by concavity and defect size. The low mean squared error (MSE) of 4.2% proved a precise estimation of the SR. Defect size as an exclusive predictor in the linear model reduced R² to 0.9 and increased the MSE to 25.7%. Furthermore, the loss of SR with increasing defect size was shown to be significantly dependent on the initial concavity. The BSSR as a single predictor for glenohumeral stability led to highest precision with MSE = 3.4%.

CONCLUSION

Glenoid concavity is a crucial factor for the SR. Independent of the defect size, the computable BSSR is a precise biomechanical estimate of the measured SR. The inclusion of glenoid concavity has the potential to influence clinical decision-making for an improved and personalised treatment of glenohumeral instability with anterior glenoid bone loss.

Trends in the Characterization of the Proximal Humerus in Biomechanical Studies: A Review

Proximal humerus fractures are becoming more common due to the aging of the population, and more related scientific research is also emerging. Biomechanical studies attempt to optimize treatments, taking into consideration the factors involved, to obtain the best possible treatment scenario. To achieve this, the use of finite element analysis (FEA) is necessary, to experiment with situations that are difficult to replicate, and which are sometimes unethical. Furthermore, low costs and time requirements make FEA the perfect choice for biomechanical studies. Part of the complete process of an FEA involves three-dimensional (3D) bone modeling, mechanical properties assignment, and meshing the bone model to be analyzed. Due to the lack of standardization for bone modeling, properties assignment, and the meshing processes, this article aims to review the most widely used techniques to model the proximal humerus bone, according to its anatomy, for FEA. This study also seeks to understand the knowledge and bias behind mechanical properties assignment for bone, and the similarities/differences in mesh properties used in previous FEA studies of the proximal humerus. The best ways to achieve these processes, according to the evidence, will be analyzed and discussed, seeking to obtain the most accurate results for FEA simulations.

Sensitivity of Neuromechanical Predictions to Choice of Glenohumeral Stability Modeling Approach

Most upper-extremity musculoskeletal models represent the glenohumeral joint with an inherently stable ball-and-socket, but the physiological joint requires active muscle coordination for stability. The authors evaluated sensitivity of common predicted outcomes (instability, net glenohumeral reaction force, and rotator cuff activations) to different implementations of active stabilizing mechanisms (constraining net joint reaction direction and incorporating normalized surface electromyography [EMG]). Both EMG and reaction force constraints successfully reduced joint instability. For flexion, incorporating any normalized surface EMG data reduced predicted instability by 54.8%, whereas incorporating any force constraint reduced predicted instability by 43.1%. Other outcomes were sensitive to EMG constraints, but not to force constraints. For flexion, incorporating normalized surface EMG data increased predicted magnitudes of joint reaction force and rotator cuff activations by 28.7% and 88.4%, respectively. Force constraints had no influence on these predicted outcomes for all tasks evaluated. More restrictive EMG constraints also tended to overconstrain the model, making it challenging to accurately track input kinematics. Therefore, force constraints may be a more robust choice when representing stability.

Primary stability analysis of stemless shoulder implants

Although the primary stability of joint implants is fundamental for successful osseointegration, little is know about this issue in the context of stemless shoulder implants. Considering 3D finite element models, the purpose of this study was to evaluate the primary stability of five stemless designs, based on the Sidus, SMR, Simpliciti, Eclipse, and Global Icon stemless systems. Three alternative bone quality conditions were considered for cancellous bone. For the Sidus, SMR, and Simpliciti designs, which do not possess a collar that sits on the cortical rim of the humeral resected surface, contact and no contact conditions were considered between the bone surface and the humeral head components. Micromotions at bone-implant interfaces promoting osseointegration were computed as a measure of primary stability for eight load cases consisting of peak in vivo joint loads measured during selected upper limb activities. Under good bone quality conditions, all stemless designs presented micromotions below 150 μm. The Eclipse-based and Global-Icon based designs were the least sensitive to bone quality. Stemless designs presenting a solid collar or contact between the humeral head component and bone provided more stability. Overall, the Eclipse-based and Global Icon-based designs presented the best performance from the primary stability point of view. However, if bone adaptation data available in the literature are considered along with the primary stability data computed here, the Global Icon-based design, as well as other designs, might be considered superior long-term options due to their better compromise between primary stability and impact on bone adaptation.

Biomechanical Testing of Additive Manufactured Proximal Humerus Fracture Fixation Plates

Achieving satisfactory fracture fixation in osteoporotic patients with unstable proximal humerus fractures remains a major clinical challenge. Varus collapse is one of the more prominent complications that may lead to screw cutout. This aim of this study was to compare the fixation provided by conventional locking plates with novel design concepts that are only feasible through additive manufacturing (AM) techniques. In addition to reversed engineered implants, two novel implant designs with integrated struts were included in the study to provide medial support to humeral head. The medial strut was either solid or included a porous lattice structure intended to promote bone ingrowth. Biomechanical tests were performed using low density synthetic bones with simulated 3-part comminuted fractures. Nondestructive torsion and compression were performed, followed by increasing cyclic loading. The relative displacements between the bone fragments were determined using a 3D motion capture system. The AM manufactured implants with medial strut showed significant reduction of varus displacement during the increasing cyclic loading when compared to conventional designs. AM reversed-engineered locking plates showed similar mechanical behavior to conventional plates with identical geometry. This study demonstrates the feasibility and potential of employing alternative design via AM for fixation of unstable comminuted proximal humerus fractures to reduce fragment displacement.

Screw configuration in proximal humerus plating has a significant impact on fixation failure risk predicted by finite element models

BACKGROUND

Proximal humeral fractures occur frequently, with fixed angle locking plates often being used for their treatment. No current quantitative evidence for the effect of different screw configurations exists, and the large number of variations makes biomechanical testing prohibitive. Therefore, we used an established and validated finite element osteosynthesis test kit to quantify the effect of variations in screw configuration on predicted failure risk of PHILOS plate fixation for unstable proximal humerus fractures.

METHODS

Twenty-six low-density humerus models were osteotomized to create malreduced unstable 3-part fractures that were virtually fixed with PHILOS plates. Twelve screw configurations were simulated: 6 using 2 screw rows, 4 using 3 rows, and 1 with either 8 or 9 screws. Three physiological loading cases were modeled and an established finite element analysis methodology was used. The average peri-screw bone strain, previously demonstrated to predict fatigue cutout failure, was used to compare the different configurations.

RESULTS

Significant differences in peri-screw strains, and thus predicted failure risk, were seen with different combinations. The 9-screw configuration demonstrated the lowest peri-screw strains. Fewer screw constructs showed lower strains when placed further apart. The calcar screws (row E) significantly (P < .001) reduced fixation failure risk.

CONCLUSION

Screw configurations significantly impact predicted cutout failure risk for locking plate fixations of unstable proximal humerus fractures in low-density bone. Although requiring clinical corroboration, the result of this study suggests that additional screws reduce peri-screw strains, the distance between them should be maximized whenever possible and the calcar screws should be used.

The influence of screw length on predicted cut-out failures for proximal humeral fracture fixations predicted by finite element simulations

BACKGROUND

The aim of this study was to identify the effect of screw length on predictions of fixation failure in three-part proximal humeral fractures using a finite element-based osteosynthesis modelling toolkit.

METHODS

A mal-reduced unstable three-part AO/OTA 11-B3.2 fracture with medial comminution was simulated in forty-two digitally processed proximal humeri covering a spectrum of bone densities and fixed with the PHILOS plate using three distal and six proximal locking screws. Four test groups were generated based on the screw tip to joint surface distance (TJD), with all proximal screws being shortened from 4 mm TJD to be 8, 12 or 16 mm TJD. Average bone strains around the screw tips, correlating with biomechanical cyclic cut-out-type failure, were evaluated in three physiological loading protocols representing simple shoulder motions. Six further groups were tested, where five of the proximal screws were inserted to 4 mm TJD and the sixth screw to 8 mm TJD.

RESULTS

Exponential increases in the predicted risk of fixation failure were seen with increased tip-to-joint distances (p < 0.001). When one of the proximal screws was placed 8 mm from the joint, with the remaining five at 4 mm distance, significant increases (p < 0.001) were registered in the strains around the screw tips in all except the two superior screws. This effect was maximal around the calcar screws (p < 0.001) and for lower density samples (p < 0.001).

CONCLUSIONS

These results suggest that longer screws provide reduced risk of cut-out failure, i.e. distalisation and/or varisation of the head fragment, and thus may decrease failure rates in proximal humeral fractures treated with angular stable plates. These findings require clinical corroboration and further studies to investigate the risk of screw perforation.

Finite element analyses for predicting anatomical neck fractures in the proximal humerus

BACKGROUND

Proximal humerus fractures which occur as a result of a fall on an outstretched arm are frequent among the elderly population. The necessity of stabilizing such fractures by surgical procedures is a controversial matter among surgeons. Validating a personalized FE analysis by ex-vivo experiments of humeri and mimicking such fractures by experiments is the first step along the path to determine the necessity of such surgeries.

METHODS

Four fresh frozen human humeri were loaded using a new simple experimental setting, so to fracture the humeri at the anatomical neck. Strains on humeri's surfaces predicted by the high order FE analyses (as in Dahan et al., 2016) were compared to the experimental observations to further enhance the validity of the FE analyses. A simplified yield criterion based on a linear elastic analysis and principal strains was used to predict the anatomical neck fracture as observed in the experiment.

FINDINGS

An excellent correlation between experimental measured and FE predicted strains was obtained (slope of 0.99 and R²=0.98). All humeri were fractured at the anatomical neck. The predicted yield load was within 10%-20% accuracy.

INTERPRETATION

High-order FE analyses reliably predict strains and yield loads in the humeri. Fractures induced by the experimental setting correspond to anatomical neck fractures noticed in practice and classified as AO C1.1-C1.3. Surgical neck fractures, which are most common in clinical practice, could not be realized in the proposed experiments, and a different experimental setting should be sought to obtain them ex-vivo.

Scapulothoracic rhythm affects glenohumeral joint force

Hypothesis

Musculoskeletal computer models provide valuable insights into shoulder biomechanics. The shoulder is a complex joint composed of glenohumeral, scapulothoracic, acromioclavicular, and sternoclavicular articulations, whose function is largely dependent on the many muscles spanning these joints. However, the range of patient-to-patient variability in shoulder function is largely unknown. We therefore assessed the sensitivity of glenohumeral forces to population-based model input parameters that were likely to influence shoulder function.

Methods

We constructed musculoskeletal models of the shoulder in the AnyBody Modeling System (AnyBody Technology, Aalborg, Denmark). We used inverse dynamics and static optimization to solve for glenohumeral joint forces during a simulated shoulder elevation. We generated 1000 AnyBody models by uniformly distributing the following input parameters: subject height, scapulohumeral rhythm, humeral head radius, and acromiohumeral interval.

Results

Increasing body height increased glenohumeral joint forces. Increasing the ratio of scapulothoracic to glenohumeral elevation also increased forces. Increasing humeral head radius and acromiohumeral interval decreased forces. The relative sensitivity of glenohumeral joint forces to input parameters was dependent on the angle of shoulder elevation. We developed an efficient method of generating and simulating musculoskeletal models representing a large population of shoulder arthroplasty patients. We found that scapulohumeral rhythm had a significant influence on glenohumeral joint force.

Conclusions

This finding underscores the importance of more accurately measuring and simulating scapulothoracic motion rather than using fixed ratios or average scapulothoracic motion. This modeling approach can be used to generate virtual populations for conducting efficient simulations and generating statistical conclusions.

Screws with larger core diameter and lower thread pitch increase the stability of locked plating in osteoporotic proximal humeral fractures

BACKGROUND

Little is known about the screw design as a factor for stability of the bone-implant interface in locking plate fixation of proximal humeral fractures. Aim of the present study was to analyze if locking screws with a large core diameter and a low thread pitch provide increased stability when compared to conventional locking screws.

METHODS

3-Part proximal humeral fractures were created in ten pairs of osteoporotic human cadaveric humeri and fixed with a locking plate. Head fixation was performed with screws with a large core diameter (soft bone screws) in one humerus and with conventional cancellous locking screws in the other humerus of each donor. Specimens were loaded in the varus bending position. Stiffness, failure loads, plate bending and motion at the bone-implant interface were evaluated using mechanical sensors and an optical motion capture system.

FINDINGS

The stiffness of the construct for the soft bone screws was 299.8 N/mm (IR, 72.1 N/mm) and 203.9 N/mm (IR, 37.3 N/mm) for the conventional locking screws (p = 0.005). Plate bending did not differ between the two groups. Motion at the bone-implant interface was significantly reduced in the soft bone screw group (p < 0.05). The median load-to-failure was significantly higher in the soft bone screw group (358 N vs. 313 N; p = 0.012).

INTERPRETATION

The use of soft bone screws is associated with less motion at the bone-implant interface and therefore greater fixation strength when compared to fixation with conventional locking screws. Clinical studies are needed to prove these biomechanical findings in the in vivo situation.

LEVEL OF EVIDENCE

Controlled laboratory study.

Polyethylene glenoid component fixation geometry influences stability in total shoulder arthroplasty

Glenoid component stability is essential to ensure successful long-term survivability following total shoulder arthroplasty. As such, this computational study assessed the stability of five all-polyethylene glenoid components (Keel, Central-Finned 4-Peg, Peripheral 4-Peg, Cross-Keel, and Inverted-Y), using simulated joint loading in an osteoarthritic patient cohort. Stability was assessed on the basis of component micromotion in the tangential and normal directions. Maximum tangential micromotion occurred in the Cross-Keel (146 ± 46 µm), which was significantly greater (p < .001) than the other components. Maximum normal micromotion occurred in the Inverted-Y (109 ± 43 µm), which was significantly greater (p ≤ .002) than the other four components. In general, the Central-Finned 4-Peg exhibited the least normal and tangential micromotion, while the keeled components shown the highest normal and tangential micromotion. This study suggests that modifications to keeled designs do not improve component stability under the conditions tested, and pegged components show superior computational stability.

Workstation configuration and container type influence upper limb posture in grocery bagging

INTRODUCTION

Repetitive movements and awkward postures are two persistent injury risk factors for grocery store cashiers. Due to the recent rise in popularity of environmentally-friendly grocery bagging options, current recommendations for cashiers are likely outdated. Correspondingly, the objective of this study was to examine the effects of cashier-specific work demands, workstation configuration, and container type on upper limb postures during typical job activities.

METHODS

Fifteen experienced cashiers bagged groceries at varying combinations of workstation height (low, medium, high) and container type (reusable bins, reusable bags, plastic bags). Upper limb movement was quantified with motion capture and amplitude probability distribution functions of humeral elevation and humeral axial internal rotation were used to assess the static (10th percentile), median (50^th percentile), and peak (90^th percentile) postural demands, which were then interpreted in the context of existing postural guidelines.

RESULTS

High workstation height and reusable bags increased right arm elevation at peak posture by 15.7° compared to the low workstation height and reusable bin combination. However, reusable bins increased internal rotation demands of the right arm by 4.3° compared to other container types. Left arm elevation and internal rotation were consistently lower than right arm angles.

CONCLUSION

Cashiers are encouraged to adjust the workstation to decrease the arm elevation and internal rotation required by higher workstation heights and tall containers, and to use both arms for scanning and packing, when possible, to reduce undesirable arm postures.

The subchondral bone layer and glenoid implant design are relevant for primary stability in glenoid arthroplasty

BACKGROUND

Clinical studies suggest that reaming of the subchondral bone layer to achieve good implant seating is a risk factor for glenoid loosening. This study aims to evaluate (1) the importance of the subchondral bone layer and (2) the influence of the design of the glenoid component.

METHODS

Different techniques for preparation of an A1 glenoid were compared: (1) preserving the subchondral bone layer; (2) removal of the subchondral bone layer; (3) implantation of a glenoid component that does not adapt to the native anatomy. Artificial glenoid bones (n = 5 each) were used with a highly standardized preparation and implantation protocol. Biomechanical testing was performed during simulated physiological shoulder motion. Using a high-resolution optical system, the micromotions between implant and bone were measured up to 10,000 motion cycles.

RESULTS

At the 10,000 cycle measuring point, significantly more micromotions were found in the subchondral layer removed group than in the subchondral layer preserved group (p = 0.0427). The number of micromotions in the nonadapted group was significantly higher than in the subchondral layer preserved group (p = 0.0003) or the subchondral layer removed group (p = 0.0207).

CONCLUSION

Conservative reaming proved important to diminish the micromotions of the glenoid component. Implantation of a glenoid component that matches with the bony underlying glenoid can help to preserve the subchondral bone layer without sacrificing proper implant seating.

Impact of Modeling Assumptions on Stability Predictions in Reverse Total Shoulder Arthroplasty

Reverse total shoulder arthroplasty (rTSA) is commonly used in the shoulder replacement surgeries for the relief of pain and to restore function, in patients with grossly deficient rotator cuff. Primary instability due to glenoid loosening is one of the critical complications of rTSA; the implants are designed and implanted such that the motion between the glenoid baseplate and underlying bone is minimized to facilitate adequate primary fixation. Finite element analysis (FEA) is commonly used to simulate the test setup per ASTM F2028-14 for comparing micromotion between designs or configurations to study the pre-clinical indications for stability. The FEA results can be influenced by the underlying modeling assumptions. It is a common practice to simplify the screw shafts by modeling them as cylinders and modeling the screw-bone interface using bonded contact, to evaluate micromotion in rTSA components. The goal of this study was to evaluate the effect of three different assumptions for modeling the screw-bone interface on micromotion predictions. The credibility of these modeling assumptions was examined by comparing the micromotion rank order predicted among three different modular configurations with similar information from the literature. Eight configurations were modeled using different number of screws, glenosphere offset, and baseplate sizes. An axial compression and shear load was applied through the glenosphere and micromotion at the baseplate-bone interface was measured. Three modeling assumptions pertaining to modeling of the screw-bone interface were used and micromotion results were compared to study the effect of number of peripheral screws, eccentricities, and baseplate diameter. The relative comparison of micromotion between configurations using two versus four peripheral screws remained unchanged irrespective of the three modeling assumptions. However, the relative comparison between two inferior offsets and baseplate sizes changed depending on the modeling assumptions used for the screw-bone interface. The finding from this study challenges the generally believed hypothesis that FEA models can be used to make relative comparison of micromotion in rTSA designs as long as the same modeling assumptions are used across all models. The comparisons with previously published work matched the finding from this study in some cases, whereas the comparison was contradicting in other cases. It is essential to validate the computer modeling approach with an experiment using similar designs and methods to increase the confidence in the predictions to make design decisions.