Efficient hydrogenation of stearic acid over carbon coated Ni Fe catalyst

Durably Superhydrophobic Magnetic Cobalt Ferrites for Highly Efficient Oil-Water Separation and Fast Microplastic Removal

Microplastic pollution has become a primary global concern in the 21st century. Recyclable magnetic particles with micro-nanostructures are considered an efficient and economical way to remove microplastics from water. In this study, superhydrophobic magnetic cobalt ferrite particles were prepared by using a simple coprecipitation method combined with surface functionalization. The micromorphology, chemical composition, hysteresis loop, and surface contact angle of the functionalized cobalt ferrite were characterized. The separation efficiency and absorption capacity of cobalt ferrite particles in water-oil separation and microplastic removal were investigated. The results showed that the saturation magnetic field intensity of cobalt ferrite was 65.52 emu/g, the residual magnetization intensity (Mr) was 18.79 emu/g, and the low coercivity was 799.83 Oe. Cobalt ferrites had stable superhydrophobicity in the pH range of 1-13. The separation efficiency of cobalt ferrite powder for four oil-water mixture separations was higher than 94.2%. The separation efficiency was as high as 99.6% in the separation of the hexane and water mixtures. Due to the synergistic effect of the hydrophobic effect and van der Waals force, the functionalized magnetic cobalt ferrite had a high and stable microplastic removal efficiency and capture capacity. The removal efficiency of microplastics was close to 100%, and the capture capacity was 2.56 g/g. After ten microplastic removal cycles, the removal efficiency reached more than 98%, and the surface contact angle was still greater than 150°.

Biomass as an alternative feedstock to oleochemicals

The huge demands for petrochemicals have led to a rapid increase in the production of these fossil-based derivatives. Biomass represents a promising feedstock for addressing the challenges related to petrochemicals in terms of the necessity to apply renewable sources and the need to decrease carbon emissions. Among the natural biomass products, most studies have attempted to upgrade natural oils owing to their promising advantages of worldwide availability, low-cost processing, and built-in functionality. This paper discusses the upgradation of natural oils to the most beneficial oleochemicals, including fatty acids, fatty alcohols, and fatty acid methyl esters. This review also covers the utility, physico-chemical properties, and the production processes for such materials. The interconnected reaction routes to produce oleochemicals and the affecting parameters (catalyst design, temperature, and pressure) are also elucidated. Furthermore, this article discusses the future perspective of oleochemicals based on their development in recent years.

Advanced Carbon-Based Nanocatalysts and their Application in Catalytic Conversion of Renewable Platform Molecules

The transformation of renewable platform molecules to produce value-added fuels and fine-chemicals is a promising strategy to sustainably meet future demands. Owing to their finely modified electronic and geometric properties, carbon-based nanocatalysts have shown great capability to regulate their catalytic activity and stability. Their well-defined and uniform structures also provide both the opportunity to explore intrinsic reaction mechanisms and the site-requirement for valorization of renewable platform molecules to advanced fuels and chemicals. This Review highlights the progress achieved in carbon-based nanocatalysts, mainly by using effective regulation approaches such as heteroatom anchoring, bimetallic synergistic effects, and carbon encapsulation to enhance catalyst performance and stability, and their applications in renewable platform molecule transformations. The foundation for understanding the structure-performance relationship of carbon-based catalysts has been established by investigating the effect of these regulation methods on catalyst performance. Finally, the opportunities, challenges and potential applications of carbon-based nanocatalysts are discussed.

Selective Hydrogenation of Stearic Acid to 1-Octadecanol Using Bimetallic Palladium-Tin Supported on Carbon Catalysts at Mild Reaction Conditions

Bimetallic palladium-tin catalysts supported on microporous carbon (denoted as Pd-Sn(x)/C, loading amount of Pd = 5 wt% and x = Pd/Sn molar ratio; c.a. 3.0; 1.5; and 1.0) showed high selectivity in the hydrogenation of stearic acid towards 1-octadecanol (stearyl alcohol) under mild reaction conditions. Pd-Sn(x)/C catalysts were synthesized via the hydrothermal method at temperature of 150 °C for 24 h, and reduced with H2 at 400 °C for 3 h. Pd-Sn(1.5)/C catalyst exhibited the highest yield of stearyl alcohol (1-octadecanol) (up to 73.2%) at 100% conversion of stearic acid at temperature 240 °C, initial H2 pressure of 3.0 MPa, a reaction time of 13 h, and in 2-propanol/water solvent. The high selectivity of alcohols over Pd-Sn(1.5)/C catalyst can be attributed to the formation of bimetallic Pd-Sn alloy phases (e.g. Pd3Sn and Pd3Sn2) as obviously depicted by XRD analysis. The presence of co-promotor Sn and the formation of bimetallic may play a pivotal role in the high selectivity of 1-octadecanol. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Efficient Reduction of Selenite to Elemental Selenium by Liquid-Phase Catalytic Hydrogenation Using a Highly Stable Multiwalled Carbon Nanotube-Supported Pt Catalyst Coated by N-Doped Carbon

A stable catalyst, Pt/carbon nanotube (CNT) coated with N-doped carbon (Pt/CNT@CN), was designed to reduce selenite (Se(IV)) in water to elemental selenium by liquid-phase catalytic hydrogenation. Commercial Pt/C, pristine Pt/CNT, and carbon-coated Pt/CNT (Pt/CNT@C) were used for benchmarking. The Pt particles in Pt/CNT@CN were completely embedded beneath the coatings to minimize leaching and were not easily accessible to Se(IV). However, Schottky-Mott-type metal-carbon junctions that activate H2 were formed on the coated catalyst, facilitating effective reduction of Se(IV). The initial activity of Pt/CNT@CN (900.5 mg L-1 gcat-1 h-1) was two times higher than that of commercial Pt/C (448.6 mg L-1 gcat-1 h-1). The commercial Pt/C and uncoated Pt/CNT lost their initial activities during reuse and were almost inactive after 10 cycles due to significant Pt leaching (>90%) during the reaction and acid-washing regeneration processes. Pt/CNT@CN maintained 33% of the initial activity after the first cycle and stabilized over the following 9 cycles due to effective protection of Pt particles by carbon coatings. After 10 cycles, the activity of Pt/CNT@CN was over 20 times higher than that of Pt/C and uncoated Pt/CNT. Overall, catalytic hydrogenation using carbon-coated-supported Pt catalysts is an effective and promising approach to remove Se(IV) in water.

Green hydroboration of carboxylic acids and mechanism investigation

A catalyst-free and solvent-free method for the hydroboration of a variety of carboxylic acids with pinacolborane was developed. The hydroboration of various aromatic and aliphatic carboxylic acids as well as dicarboxylic acids with HBpin could be completed within 6 h at room temperature or within 1 h at 60 °C to give the products in quantitative yields under neat conditions without the need for any solvent or metal catalyst. The possible reaction mechanism was investigated in detail based on the corresponding DFT calculations and the stoichiometric reaction of acetic acid with different equivalents of HBpin (at room temperature and 0 °C) and it revealed the stepwise nature of the protocol.

Ni Promotion by Fe: What Benefits for Catalytic Hydrogenation?

Metallic nickel is known to efficiently catalyze hydrogenation reactions, but one of its major drawbacks lies in its lack of selectivity, linked to side-reactions of hydrogenolysis and over-hydrogenation. More selective hydrogenations can be obtained upon the introduction of a second metal in combination with Ni. Fe is an interesting choice, as it is a cheap and abundant metal. This review aims at discussing the advantages and constraints brought by the preparation procedures of bimetallic supported Ni–Fe nanoparticles, and at analyzing the benefits one can draw by substituting Ni–Fe supported catalysts for Ni monometallic systems for the catalytic hydrogenation of organic molecules. Specific formulations, such as Ni75Fe25, will be singled out for their high activity or selectivity, and the various hypotheses behind the roles played by Fe will be summarized.