Electrospun nanofibers of V-doped TiO2 with high photocatalytic activity

Preparation and Property Characterization of In2YSbO7/BiSnSbO6 Heterojunction Photocatalyst toward Photocatalytic Degradation of Indigo Carmine within Dye Wastewater under Visible-Light Irradiation

In₂YSbO₇ and In₂YSbO₇/BiSnSbO₆ heterojunction photocatalyst were prepared by a solvothermal method for the first time. The structural characteristics of In₂YSbO₇ had been represented. The outcomes showed that In₂YSbO₇ crystallized well and possessed pyrochlore constitution, a stable cubic crystal system and space group Fd3m. The lattice parameter of In₂YSbO₇ was discovered to be a = 11.102698 Å and the band gap energy of In₂YSbO₇ was discovered to be 2.68 eV, separately. After visible-light irradiation of 120 minutes (VLGI-120M), the removal rate (ROR) of indigo carmine (IC) reached 99.42% with In₂YSbO₇/BiSnSbO₆ heterojunction (IBH) as a photocatalyst. The ROR of total organic carbon (TOC) reached 93.10% with IBH as a photocatalyst after VLGI-120M. Additionally, the dynamics constant k which was taken from the dynamic curve toward (DCT) IC density and VLGI time with IBH as a catalyst reached 0.02950 min^-1. The dynamics constant k which came from the DCT TOC density and VLGI time with IBH as a photocatalyst reached 0.01783 min^-1. The photocatalytic degradation of IC in dye wastewater (DW) with IBH as a photocatalyst under VLGI was in accordance with the first-order kinetic curves. IBH was used to degrade IC in DW for three cycles of experiments under VLGI, and the ROR of IC reached 98.74%, 96.89% and 94.88%, respectively, after VLGI-120M, indicating that IBH had high stability. Compared with superoxide anions or holes, hydroxyl radicals possessed the largest oxidative ability for removing IC in DW, as demonstrated by experiments with the addition of trapping agents. Lastly, the probable degradation mechanism and degradation pathway of IC were revealed in detail. The results showed that a visible-light-responsive heterojunction photocatalyst which possessed high catalytic activity and a photocatalytic reaction system which could effectively remove IC in DW were obtained. This work provided a fresh scientific research idea for improving the performance of a single catalyst.

Tuning of Sm3+ and Er3+-doped TiO2 nanofibers for enhancement of the photocatalytic performance: Optimization of the photodegradation conditions

Titanium dioxide (TiO₂)-based nanofibers doped with samarium (Sm³⁺) and erbium (Er³⁺) at doping levels tuned in the range of 0.05-1.0% were prepared by the electrospinning-calcination method. The produced materials were well characterized by X-ray diffraction, SEM, EDX, and UV-vis diffuse reflectance spectroscopy. These one-dimensional nanostructures showed a crystalline structure with values of fiber diameters values between 60 and 100 nm. The best catalyst sample of this study was formulated as TiO₂:Sm (0.1%) and sintered at 600 °C. And, it was employed to intensify the photocatalytic process under visible-light irradiation. Likewise, the chemometric approach was applied to optimize the process. The results revealed that the rate constant for the photo-degradation of a cationic organic pollutant was significantly improved (k = 3.496 × 10^-1 min^-1). In terms of the reaction half-life, the intensification and optimization of the process led to a decrease in the half-life of the reaction from 68 to 2 min. And, these are outstanding findings for the photo-degradation process under visible-light irradiation. In addition, the total organic carbon (TOC) removal efficiencies were found to be 69.95% and 72.30% for the mineralization of MB and CIP, respectively, after a 360 min reaction time, which are significant results. Moreover, this material demonstrated remarkable photocatalytic activity for the degradation of ciprofloxacin (CIP) with a 99.6% removal efficiency and a rate constant of 4.292 × 10^-1 min^-1. Finally, the stability and reusability of this catalyst were demonstrated during five repetitive cycles of the CIP photodegradation.

Preparation, Property Characterization of Gd2YSbO7/ZnBiNbO5 Heterojunction Photocatalyst for Photocatalytic Degradation of Benzotriazole under Visible Light Irradiation

The Gd2YSbO7/ZnBiNbO5 heterojunction photocatalyst was synthesized for the first time by the facile in situ precipitation method. The structural properties of a Gd2YSbO7/ZnBiNbO5 heterojunction photocatalyst were characterized by X-ray diffractometer, scanning electron microscope-X ray energy dispersive spectra, X-ray photoelectron spectrograph and UV-Vis diffuse reflectance spectrophotometer. The band gap energy (BGE) of Gd2YSbO7 or ZnBiNbO5 was found to be 2.396 eV or 2.696 eV, respectively. The photocatalytic property of Gd2YSbO7 or ZnBiNbO5 or Gd2YSbO7/ZnBiNbO5 heterojunction photocatalyst (GZHP) was reported. After a visible-light irradiation of 145 minutes (VLI-145 min), the removal rate (RER) of benzotriazole reached 99.05%, 82.45%, 78.23% or 47.30% with Gd2YSbO7/ZnBiNbO5 heterojunction (GZH), Gd2YSbO7, ZnBiNbO5 or N-doped TiO2 (NTO) as photocatalyst. In addition, the kinetic constant k, derived from the dynamic curve toward benzotriazole concentration and visible light irradiation time with GZH as a photocatalyst, reached 0.0213 min−1. Compared with Gd2YSbO7 or ZnBiNbO5 or NTO, GZHP showed maximal photocatalytic activity (PHA) for the photocatalytic degradation of benzotriazole under visible-light irradiation. The RER of total organic carbon during the photocatalytic degradation of benzotriazole reached 90.18%, 74.35%, 70.73% or 42.15% with GZH as a photocatalyst or with Gd2YSbO7, ZnBiNbO5 or NTO as a photocatalyst after VLI-145 min. Moreover, the kinetic constant k, which came from the dynamic curve toward total organic carbon concentration and visible light irradiation time with GZH as a photocatalyst, reached 0.0110 min−1. Based on above results, GZHP showed the maximal mineralization percentage ratio when GZHP degraded benzotriazole. The results showed that hydroxyl radicals was the main oxidation radical during the degradation of benzotriazole. The photocatalytic degradation of benzotriazole with GZH as a photocatalyst conformed to the first-order reaction kinetics. Our research aimed to improve the photocatalytic properties of the single photocatalyst.

Synthesis, Property Characterization and Photocatalytic Activity of the Ag3PO4/Gd2BiTaO7 Heterojunction Catalyst under Visible Light Irradiation

A new type of Gd2BiTaO7 nanocatalyst (GBT) was synthesized by a high-temperature solid-phase method, and a heterojunction photocatalyst, which was composed of GBT and silver phosphate (AP), was prepared by the facile in-situ precipitation method for the first time. The photocatalytic property of GBT or the Ag3PO4/Gd2BiTaO7 heterojunction photocatalyst (AGHP) was reported. The structural properties of GBT and AGHP were characterized by an X-ray diffractometer, scanning electron microscope–X-ray energy dispersive spectra, an X-ray photoelectron spectrograph, a synchrotron-based ultraviolet photoelectron spectroscope, a Fourier transform infrared spectrometer, an UV-Vis diffuse reflectance spectrophotometer and an electron paramagnetic resonance spectrometer. The results displayed that GBT was well crystallized with a stable cubic crystal system and space group Fd3m. The lattice parameter or band gap energy of GBT was found to be a = 10.740051 Å or 2.35 eV, respectively. After visible light irradiation of 30 min, the removal rate of bisphenol A (BPA) reached 99.52%, 95.53% or 37.00% with AGHP as the photocatalyst, with Ag3PO4 and potassium persulfate (AP-PS) as photocatalysts or with N-doped TiO2 (NT) as a photocatalyst, respectively. According to the experimental data, it could be found that the removal rate of BPA with AGHP as a photocatalyst was 2.69 times higher than that with NT as a photocatalyst. AGHP showed higher photocatalytic activity for photocatalytic degradation of BPA under visible light irradiation compared with GBT or AP-PS or NT. The removal rate of total organic carbon (TOC) was 96.21%, 88.10% or 30.55% with AGHP as a photocatalyst, with AP-PS as photocatalysts or with NT as a photocatalyst after visible light irradiation of 30 min. The above results indicated that AGHP possessed the maximal mineralization percentage ratio during the process of degrading BPA compared with GBT or AP-PS or NT. The results indicated that the main oxidation radical was •OH during the process of degrading BPA. The photocatalytic degradation of BPA with AGHP as a photocatalyst conformed to the first-order reaction kinetics. This study provided inspiration for obtaining visible light-responsive heterojunction photocatalysts with high catalytic activity and efficient removal technologies for organic pollutants and toxic pollutants, and as a result, the potential practical applications of visible light-responsive heterojunction photocatalysts were widened. The subsequent research of thin-film plating of the heterojunction catalysts and the construction of complete photoluminescent thin-film catalytic reaction systems, which utilized visible light irradiation, could provide new technologies and perspectives for the pharmaceutical wastewater treatment industry.

Photocatalytic Activity of Nanocoatings Based on Mixed Oxide V-TiO2 Nanoparticles with Controlled Composition and Size

V-TiO2 photocatalyst with 0 ≤ V ≤ 20 mol% was prepared via the sol–gel method based on mixed oxide titanium–vanadium nanoparticles with size and composition control. The mixed oxide vanadium–titanium oxo-alkoxy nanonoparticles were generated in a chemical micromixing reactor, coated on glass beads via liquid colloid deposition method and underwent to an appropriate thermal treatment forming crystallized nanocoatings. X-ray diffraction, Raman, thermogravimetric and differential thermal analyses confirmed anatase crystalline structure at vanadium content ≤ 10 mol%, with the cell parameters identical to those of pure TiO2. At a higher vanadium content of ~20 mol%, the material segregation began and orthorhombic phase of V2O5 appeared. The crystallization onset temperature of V-TiO2 smoothly changed with an increase in vanadium content. The best photocatalytic performance towards methylene blue decomposition in aqueous solutions under UVA and visible light illuminations was observed in V-TiO2 nanocoatings with, respectively, 2 mol% and 10 mol% vanadium.

Electrospun-based TiO2 nanofibers for organic pollutant photodegradation: a comprehensive review

Titanium dioxide (TiO2) is commonly used as a photocatalyst in the removal of organic pollutants. However, weaknesses of TiO2 such as fast charge recombination and low visible light usage limit its industrial application. Furthermore, photocatalysts that are lost during the treatment of pollutants create the problem of secondary pollutants. Electrospun-based TiO2 fiber is a promising alternative to immobilize TiO2 and to improve its performance in photodegradation. Some strategies have been employed in fabricating the photocatalytic fibers by producing hollow fibers, porous fibers, composite TiO2 with magnetic materials, graphene oxide, as well as doping TiO2 with metal. The modification of TiO2 can improve the absorption of TiO2 to the visible light area, act as an electron acceptor, provide large surface area, and promote the phase transformation of TiO2. The improvement of TiO2 properties can enhance carrier transfer rate which reduces the recombination and promotes the generation of radicals that potentially degrade organic pollutants. The recyclability of fibers, calcination effect, photocatalytic reactors used, operation parameters involved in photodegradation as well as the commercialization potential of TiO2 fibers are also discussed in this review.

Multilevel polarization-fields enhanced capture and photocatalytic conversion of particulate matter over flexible schottky-junction nanofiber membranes

Atmospheric Particulate matter (PM) with small sizes has caused a serious air-pollution problem calling for high-performance PM-capture materials and promising remediation strategies. In this contribution, we propose a new idea to proactively capture PM and simultaneously in-situ convert the captured PM pollution over the flexible schottky-junctions nanofiber membrane (NFM) consisting of rutile TiO₂ nanoparticles (NPs)-decorated electrospun carbon NFs. We also demonstrate that both the interfacial electron-transfer process at the TiO₂/carbon schottky-junctions and the photo-excitation process at the surface of TiO₂ NPs can induce polarization fields in the TiO₂/carbon NFM due to the difference of the space-charge distribution. These multilevel polarization fields can drive the long-range electrostatic force to enhance the proactive PM-capture ability of the NFM. As such, the TiO₂/carbon NFM exhibited a satisfactory quality factor (0.11 Pa^-1) for balancing the PM_2.5-filtration efficiency (99.92 %) and the pressure drop (only 63 Pa). More importantly, upon UV-vis-light irradiation, 92.98 % of the ultrafine PM_0.3 was removed over this TiO₂/carbon NFM. Furthermore, the as-captured PM on the NFM could be photocatalytically decomposed by the photoactive-component of TiO₂ NPs, during which some of the carbonaceous PM was converted into the fuels of such CO and CH₄ through a multi-step photoreaction.

Graphene Quantum Dots Doped PVDF(TBT)/PVP(TBT) Fiber Film with Enhanced Photocatalytic Performance

We report the fabrication of polyvinylidene fluoride (tetrabutyl titanate)/polyvinyl pyrrolidone ((tetrabutyl titanate))-graphene quantum dots [PVDF(TBT)/PVP(TBT)-GQDs] film photocatalyst with enhanced photocatalytic performance. The polyvinylidene fluoride (tetrabutyl titanate)/polyvinyl pyrrolidone ((tetrabutyl titanate)) [PVDF(TBT)/PVP(TBT)] film was first prepared with a dual-electrospinning method and then followed by attaching graphene quantum dots (GQDs) to the surface of the composite film through a hydrothermal method. Later, part of the PVP in the composite film was dissolved by a hydrothermal method. As a result, a PVDF(TBT)/PVP(TBT)-GQDs film photocatalyst with a larger specific surface area was achieved. The photocatalytic degradation behavior of the PVDF(TBT)/PVP(TBT)-GQDs film photocatalyst was examined by using Rhodamine B as the target contaminant. The PVDF(TBT)/PVP(TBT)-GQDs photocatalyst showed a higher photocatalytic efficiency than PVDF(TBT)-H2O, PVDF(TBT)/PVP(TBT)-H2O, and PVDF(TBT)-GQDs, respectively. The enhanced photocatalytic efficiency can be attributed to the broader optical response range of the PVDF(TBT)/PVP(TBT)-GQDs photocatalyst, which makes it useful as an effective photocatalyst under white light irradiation.

Fabrication and photocatalytic activity of TiO2 composite membranes via simultaneous electrospinning and electrospraying process

In present study, a simultaneous electrospinning and electrospraying (SEE) process was employed to produce microclusters of TiO₂ nanoparticles and interlock them in nanofibrous network. The photocatalytic composite membranes (PCMs) were fabricated by electrospraying TiO₂ nanoparticle suspension into microcluster form that dispersed and entrapped within nylon-6 electrospun fiber membrane. Three PCMs membrane with TiO₂ content of 52.0, 83.6, and 91.7wt.% were successfully fabricated. The membrane consisted of TiO₂ microclusters, ranging in sizes from around 0.3 to 10μm, distributed uniformly within the nylon-6 nanofibrous network. PCMs photocatalytic activity against Methylene Blue (MB) in aqueous solution showed more than 98% MB removal efficiency after 120min of photocatalytic oxidation (PCO) for all PCMs. For PCM with the highest TiO₂ content tested for 5 PCO cycles, it was found that most of their TiO₂ content remained incorporated within the nanofibrous structure. The concept of nanoparticles clusters entrapment with SEE fabrication employed here provide a simple and effective method for reducing detachment of nanostructure phase from nanocomposite membrane.

Single step aerosol assisted chemical vapor deposition of p–n Sn(ii) oxide–Ti(iv) oxide nanocomposite thin film electrodes for investigation of photoelectrochemical properties

Novel p–n SnO–TiO₂ nanocomposite film electrodes were fabricated through a single step method and their photoelectrocatalytic properties were evaluated.

Dual Functional Ta-Doped Electrospun TiO2 Nanofibers with Enhanced Photocatalysis and SERS Detection for Organic Compounds

There is a growing interest in multifunctional nanomaterials for the detection as well as degradation of organic contaminants in the water. In this work, we report on the development of dual functional TiO₂ nanofibers (TNF) with different tantalum (Ta) doping (1-10 mol %) by a simple electrospinning technique. As-prepared TNF show mesoporous dominant structure, which are favorable for photocatalytic activity due to the presence of catalytic spots. Ta doping decreases the crystalline size within TiO₂ matrix because of the incorporation of Ta⁵⁺ ions and restricts the phase transformation from anatase to rutile. Ta doping slightly enhances the visible light absorption because of the Ti³⁺ defects sites created upon Ta⁵⁺ doping. The effect of Ta doping within TiO₂ matrix was systematically studied for the degradation of methylene blue (MB) dye under ultraviolet (UV) and solar light irradiation. The 5% Ta-doped TNF were found to be optimal and showed 5.1 and 2.2 times higher photocatalytic activity as compared to TNF under UV and solar light irradiation, respectively. The effect of Ta doping for the detection of MB molecules was also studied by surface enhanced Raman scattering (SERS). It was observed that 5% Ta-doped TNF exhibit higher photocatalytic activity and enhanced SERS signals of adsorbed MB molecules as compared to the TNF. The enhanced photocatalytic and SERS activities can be explained as combined effects of enhanced visible light absorption, lower crystalline size, and slightly higher surface area. The observed results show that Ta doping induces new energy levels below the conduction band of TiO₂ because of Ti³⁺ defects, which inhibit the photogenerated charge recombination acting as electron traps and promote charge transfer mechanism acting as an intermediate state for TiO₂ to MB molecule electron transfer, and are mainly responsible for the enhanced photocatalytic and SERS activities, respectively.

Advances in Photocatalytic CO₂ Reduction with Water: A Review

In recent years, the increasing level of CO₂ in the atmosphere has not only contributed to global warming but has also triggered considerable interest in photocatalytic reduction of CO₂. The reduction of CO₂ with H₂O using sunlight is an innovative way to solve the current growing environmental challenges. This paper reviews the basic principles of photocatalysis and photocatalytic CO₂ reduction, discusses the measures of the photocatalytic efficiency and summarizes current advances in the exploration of this technology using different types of semiconductor photocatalysts, such as TiO₂ and modified TiO₂, layered-perovskite Ag/ALa₄Ti₄O₁₅ (A = Ca, Ba, Sr), ferroelectric LiNbO₃, and plasmonic photocatalysts. Visible light harvesting, novel plasmonic photocatalysts offer potential solutions for some of the main drawbacks in this reduction process. Effective plasmonic photocatalysts that have shown reduction activities towards CO₂ with H₂O are highlighted here. Although this technology is still at an embryonic stage, further studies with standard theoretical and comprehensive format are suggested to develop photocatalysts with high production rates and selectivity. Based on the collected results, the immense prospects and opportunities that exist in this technique are also reviewed here.

Simultaneous Cu doping and growth of TiO2 nanocrystalline array film as a glucose biosensor

Copper ion doping and growth of a TiO₂ nanocrystalline material can be realized by using colloidal nanoparticles as a reactive precursor. Such an efficient doping design facilitates the use of TiO₂ as a potential biosensor for glucose molecules.

Characterization and improved solar light activity of vanadium doped TiO2/diatomite hybrid catalysts

V-doped TiO2/diatomite composite photocatalysts with different vanadium concentrations were synthesized by a modified sol-gel method. The diatomite was responsible for the well dispersion of TiO2 nanoparticles on the matrix and consequently inhibited the agglomeration. V-TiO2/diatomite hybrids showed red shift in TiO2 absorption edge with enhanced absorption intensity. Most importantly, the dopant energy levels were formed in the TiO2 bandgap due to V(4+) ions substituted to Ti(4+) sites. The 0.5% V-TiO2/diatomite photocatalyst displayed narrower bandgap (2.95 eV) compared to undoped sample (3.13 eV) and other doped samples (3.05 eV) with higher doping concentration. The photocatalytic activities of V doped TiO2/diatomite samples for the degradation of Rhodamine B under stimulated solar light illumination were significantly improved compared with the undoped sample. In our case, V(4+) ions incorporated in TiO2 lattice were responsible for increased visible-light absorption and electron transfer to oxygen molecules adsorbed on the surface of TiO2 to produce superoxide radicals ˙O2(-), while V(5+) species presented on the surface of TiO2 particles in the form of V2O5 contributed to e(-)-h(+) separation. In addition, due to the combination of diatomite as support, this hybrid photocatalyst could be separated from solution quickly by natural settlement and exhibited good reusability.

Structure characteristics and photoactivity of simultaneous luminescence and photocatalysis in CaV2O6 nanorods synthesized by the sol–gel Pechini method

CaV₂O₆ nanorods show simultaneous luminescent and photocatalytic activities meaning that CaV₂O₆ could be a potential photoactive material with a layered structure constructed by line-arranged VO₅ units.

p-MoO3 nanostructures/n-TiO2 nanofiber heterojunctions: controlled fabrication and enhanced photocatalytic properties

In this work, p-MoO3 nanostructures/n-TiO2 nanofiber heterojunctions (p-MoO3/n-TiO2-NF-HJs) were obtained by a two-step fabrication route. First, MoO2 nanostructures were hydrothermally grown on electrospun TiO2 nanofibers. Second, by thermal treatment of the obtained MoO2 nanostructures/TiO2 nanofibers, p-MoO3/n-TiO2-NF-HJs were obtained due to the phase transition of MoO2 to MoO3. With increasing the concentration of molybdenum precursor in hydrothermal process, the morphologies of MoO2 changed from nanoparticles to nanosheets, and then fully covered shells with an increased loading on TiO2 nanofibers. After calcination, the obtained p-MoO3/n-TiO2-NF-HJs possessed similar morphology to that without thermal treatment. X-ray photoelectron spectra showed that both Ti 2p and OTi-O 1s peaks of p-MoO3/n-TiO2-NF-HJs shifted to higher binding energies than that of TiO2 nanofibers, suggesting electron transfer from TiO2 to MoO3 in the formation of p-n nanoheterojunctions. The p-n nanoheterojunctions decreased photoluminescence intensity, suppressed photogenerated electrons and holes recombinations, and enhanced charge separation and photocatalytic efficiencies. The apparent first-order rate constant for the degradation of RB by p-MoO3/n-TiO2-NF-HJs with nanosheets surface morphology was two times that of TiO2 nanofibers. For the core/shell structure of p-MoO3/n-TiO2-NF-HJs, the internal electric field of p-n junction forced the photogenerated electrons transferring to TiO2 cores, then decreased the surface photocatalytic reactions and led to the lowest photocatalytic activity among the p-MoO3/n-TiO2-NF-HJs.

Self-organized vanadium and nitrogen co-doped titania nanotube arrays with enhanced photocatalytic reduction of CO2 into CH4

Self-organized V-N co-doped TiO2 nanotube arrays (TNAs) with various doping amount were synthesized by anodizing in association with hydrothermal treatment. Impacts of V-N co-doping on the morphologies, phase structures, and photoelectrochemical properties of the TNAs films were thoroughly investigated. The co-doped TiO2 photocatalysts show remarkably enhanced photocatalytic activity for the CO2 photoreduction to methane under ultraviolet illumination. The mechanism of the enhanced photocatalytic activity is discussed in detail.

Hierarchical assembly of ultrathin hexagonal SnS2 nanosheets onto electrospun TiO2 nanofibers: enhanced photocatalytic activity based on photoinduced interfacial charge transfer

Well-designed hierarchical nanostructures with one dimensional (1D) TiO(2) nanofibers (120-350 nm in diameter and several micrometers in length) and ultrathin hexagonal SnS(2) nanosheets (40-70 nm in lateral size and 4-8 nm in thickness) were successfully synthesized by combining the electrospinning technique (for TiO(2) nanofibers) and a hydrothermal growth method (for SnS(2) nanosheets). The single-crystalline SnS(2) nanosheets with a 2D layered structure were uniformly grown onto the electrospun TiO(2) nanofibers consisted of either anatase (A) phase or anatase-rutile (AR) mixed phase TiO(2) nanoparticles. The definite heterojunction interface between SnS(2) nanosheets and TiO(2) (A or R) nanoparticles were investigated by high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS). Moreover, the as-prepared SnS(2)/TiO(2) hierarchical nanostructures as nanoheterojunction photocatalysts exhibited excellent UV and visible light photocatalytic activities for the degradation of organic dyes (rhodamine B and methyl orange) and phenols (4-nitrophenol), remarkably superior to the TiO(2) nanofibers and the SnS(2) nanosheets, mainly owing to the photoinduced interfacial charge transfer based on the photosynergistic effect of the SnS(2)/TiO(2) heterojunction. Significantly, the SnS(2)/TiO(2) (AR) hierarchical nanostructures as the tricomponent heterojunction system possessed stronger photocatalytic activity than the bicomponent heterojunction system of SnS(2)/TiO(2) (A) hierarchical nanostructures or TiO(2) (AR) nanofibers, which was discussed in terms of the three-way photosynergistic effect between SnS(2), TiO(2) (A) and TiO(2) (R) component in the SnS(2)/TiO(2) (AR) heterojunction resulting in the high separation efficiency of photoinduced electron-hole pairs, as evidenced by photoluminescence (PL) and surface photovoltage spectra (SPS).

Iron phthalocyanine/TiO2 nanofiber heterostructures with enhanced visible photocatalytic activity assisted with H2O2

One-dimensional 2,9,16,23-tetra-nitrophthalocyanine iron(II) (TNFePc)/TiO(2) nanofiber heterostructures have been successfully obtained by a simple combination of electrospinning technique and solvothermal process. The as-obtained products were characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray (EDX) spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and IR spectrum. The results revealed that the TNFePc nanosheets were successfully grown on the primary TiO(2) nanofibers. And, the coverage density of the secondary TNFePc nanostructures could be controlled by adjusting the experimental parameters. Photocatalytic tests displayed that the H(2)O(2) assisted TNFePc/TiO(2) nanofiber heterostructures (TNFePc/TiO(2)-H(2)O(2)) possessed a much higher degradation rate of methyl orange than the pure TiO(2) and TNFePc/TiO(2) nanofiber without H(2)O(2) under visible light. Moreover, the TNFePc/TiO(2) nanofiber heterostructures could be easily recycled without the decrease of the photocatalytic activity due to their one-dimensional nanostructural property of TiO(2) nanofibers.

AgIO3-modified AgI/TiO2 composites for photocatalytic degradation of p-chlorophenol under visible light irradiation

Semiconducting silver iodate (AgIO(3)) was used to modify the visible light response of an AgI/TiO(2) (AIT) catalyst by a facile method. The uncalcined AIT (AITun) and AIT calcined at 200°C (AIT200) consisted of AgIO(3), AgI, and TiO(2) semiconductors, while that calcined at 450 °C (AIT450) was composed of AgI and TiO(2). The activity in p-chlorophenol (PCP) degradation under visible light irradiation using either AITun or AIT200 was much higher than that with AIT450, which was mainly attributed to the fact that the presence of AgIO(3) provided a new matching band potential. AIT200 exhibited better photocatalytic properties than AITun due to its higher crystallinity after calcination. Moreover, the high catalytic activity of AIT200 was maintained after five successive cyclic experiments under visible irradiation. Considering the effect of radical scavengers and N(2) purging on the photocatalysis process, we deduced that the probable pathway of PCP degradation was mainly a surface charge process, caused by valence band holes.

Simulated-sunlight-activated photocatalysis of methylene blue using cerium-doped SiO2/TiO2 nanostructured fibers

Cerium-doped SiO2/TiO2 nanostructured fibers were fabricated by electrospinning technology. The prepared fibers were characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Using the fibers as catalysts, photocatalytic degradation of Methylene Blue (MB) aqueous solution was carried out under simulated sunlight. The 0.2% Ce doping proved to be the optimal concentration for the doping of TiO2/SiO2, compared to other Ce-doped molar concentrations. The 0.2% Ce-doped SiO2/TiO2 fibers exhibited higher photocatalytic activity than industrial Degussa P25 and the samples doped with only Ce or SiO2. The reasons for improving the photocatalytic activity were also discussed. Several operational parameters were studied, which showed that the photocatalytic efficiency of MB was influenced by parameters such as the initial dye concentration, the initial pH, inorganic anions, and so on. In addition, the influences of an electron acceptor and a radical scavenger suggested that OH was the dominant photooxidant during the photocatalytic process. The reuse evaluation of the fibers indicated that their photocatalytic activity had good stability.

Hierarchical nanostructures of copper(II) phthalocyanine on electrospun TiO(2) nanofibers: controllable solvothermal-fabrication and enhanced visible photocatalytic properties

In the present work, 2,9,16,23-tetranitrophthalocyanine copper(II) (TNCuPc)/TiO(2) hierarchical nanostructures were successfully fabricated by a simple combination method of electrospinning technique and solvothermal processing. Scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, X-ray diffraction (XRD), UV-vis diffuse reflectance (DR), Fourier transform infrared spectrum (FT-IR), X-ray photoelectron spectroscopy (XPS), and thermal gravimetric and differential thermal analysis (TG-DTA) were used to characterize the as-synthesized TNCuPc/TiO(2) hierarchical nanostructures. The results showed that the secondary TNCuPc nanostructures were not only successfully grown on the primary TiO(2) nanofibers substrates but also uniformly distributed without aggregation. By adjusting the solvothermal fabrication parameters, the TNCuPc nanowires or nanoflowers were facilely fabricated, and also the loading amounts of TNCuPc could be controlled on the TNCuPc/TiO(2) hierarchical nanostructural nanofibers. And, there might exist the interaction between TNCuPc and TiO(2). A possible mechanism for the formation of TNCuPc/TiO(2) hierarchical nanostructures was suggested. The photocatalytic studies revealed that the TNCuPc/TiO(2) hierarchical nanostructures exhibited enhanced photocatalytic efficiency of photodegradation of Rhodamine B (RB) compared with the pure TNCuPc or TiO(2) nanofibers under visible-light irradiation.