Synthesis and characterization of nanostructural polymer–silica composite: Positron annihilation lifetime spectroscopy study

Vapour-phase method in the synthesis of polymer-ibuprofen sodium-silica gel composites

The study discusses the synthesis of polymer-silica composites comprising water soluble drug (ibuprofen sodium, IBS). The polymers selected for this study were poly(TRIM) and poly(HEMA-co-TRIM) produced in the form of permanently porous beads via the suspension-emulsion polymerization method. The acid and base set ternary composites were prepared by the saturation of the solid dispersions of drug (poly(TRIM)-IBS and/or poly(HEMA-co-TRIM)-IBS) with TEOS, and followed by their exposition to the vapour mixture of water and ammonia, or water and hydrochloric acid, at autogenous pressure. The conducted analyses reveal that the internal structure and total porosity of the resulting composites strongly depend on the catalyst which was used for silica precursor gelation. The parameters characterizing the porosity of both of the acid set composites are much lower than the parameters of the base set composites. Moreover, the basic catalyst supplied in the vapour phase does not affect the ibuprofen sodium molecules, whereas the acid one causes transformation of the ibuprofen sodium into the sodium chloride and a derivative of propanoic acid, which is poorly water soluble. The release profiles of ibuprofen sodium from composites demonstrate that there are differences in the rate and efficiency of drug desorption from them. They are mainly affected by the chemical character of the polymeric carrier but are also associated with the restricted swelling of the composites in the buffer solution after precipitation of silica gel.

Insights into the pores of microwave-assisted metal–imidazolate frameworks showing enhanced gas sorption

Microwave assisted synthesized materials have an inherent ability to trap extra linkers, thereby reducing the pore sizes of CE- heating materials to ultra/micropores. These ultramicropores are responsible for high gas sorption.

Probing Sub-atomistic Free-Volume Imperfections in Dry-Milled Nanoarsenicals with PAL Spectroscopy

Structural transformations caused by coarse-grained powdering and fine-grained mechanochemical milling in a dry mode were probed in high-temperature modification of tetra-arsenic tetra-sulfide known as β-As4S4. In respect to X-ray diffraction analysis, the characteristic sizes of β-As4S4 crystallites in these coarse- and fine-grained powdered pellets were 90 and 40 nm, respectively. Positron annihilation lifetime spectroscopy was employed to characterize transformations occurred in free-volume structure of these nanoarsenicals. Experimentally measured positron lifetime spectra were parameterized in respect to three- or two-term fitting procedures and respectively compared with those accumulated for single crystalline realgar α-As4S4 polymorph. The effect of coarse-grained powdering was found to result in generation of large amount of positron and positronium Ps trapping sites inside arsenicals in addition to existing ones. In fine-grained powdered β-As4S4 pellets, the positron trapping sites with characteristic free volumes close to bi- and tri-atomic vacancies were evidently dominated. These defects were supposed to originate from grain boundary regions and interfacial free volumes near aggregated β-As4S4 crystallites. Thus, the cumulative production of different positron traps with lifetimes close to defect-related lifetimes in realgar α-As4S4 polymorph was detected in fine-grained milled samples.

Effects of the molecular level dispersion of graphene oxide on the free volume characteristics of poly(vinyl alcohol) and its impact on the thermal and mechanical properties of their nanocomposites

The effects of the molecular dispersion of graphene oxide on (A) the crystallinity of PVA–GO nanocomposite films and (B) nanohole size distribution in the amorphous region of PVA–GO nanocomposite films.

Influence of the filler on thermal properties of porous VP-TRIM copolymers

In this paper, the synthesis and characterization of thermal properties of porous copolymers 1-vinyl-2-pyrrolidone with trimethylolpropane trimethacrylate are presented. They were obtained by suspension polymerization as a pure polymers or composite materials with different inorganic fillers. The influence of the type of filler on the textural and thermal properties was investigated in details. It was found that the value of the porous surface area of composites is much lower than in the case of pure copolymers. Thermal properties of the obtained materials were investigated by the means of thermogravimetry and differential scanning calorimetry.

Synthesis of aspirin-loaded polymer-silica composites and their release characteristics

This study describes a novel approach to the synthesis of polymer-drug-silica nanocomposites via encapsulation/isolation of drug molecules, introduced into the polymer matrix by the silica gel. For the first time, tetraethoxysilane (TEOS) gelation in the vapor phase of the acidic catalyst is presented as an efficient method to enter the silica gel nanoparticles into the polymer-aspirin conjugate. The conducted studies reveal that the internal structure of the polymer carrier is significantly reorganized after the embedding of aspirin molecules and the silica gel. The total porosity of the polymer-drug-silica nanocomposites and the molecular structure of the silica gel embedded in the system strongly depend on the conditions of the silica source transformation. Additionally, the release of the drug was fine-tuned by adapting the conditions of hydrolysis and condensation of the silica gel precursor. Finally, to prove the usefulness of the proposed synthesis, the controlled release of aspirin from the polymer-drug-silica nanocomposites is demonstrated.

Nanostructured polymer-titanium composites and titanium oxide through polymer swelling in titania precursor

Polymer (XAD7HP)/Ti⁴⁺ nanocomposites were prepared through the swelling of polymer in titanium (IV) ethoxide as a titanium dioxide precursor. The nanocomposite beads exhibit relatively high porosity different than the porosity of the initial polymer. Thermal treatment of composite particles up to 200 °C in vacuum causes the change of their internal structure. At higher temperature, the components of composite become more tightly packed. Calcination at 600 °C and total removal of polymer produce spherically shaped TiO₂ condensed phase as determined by XRD. Thermally treated composites show the substantial change of pore dimensions within micro- and mesopores. The presence of micropores and their transformation during thermal processing was studied successfully by positron annihilation lifetime spectroscopy (PALS). The results derived from PALS experiment were compared with those obtaining from low-temperature nitrogen adsorption data.