Selective extraction of uranyl ions using ion-imprinted chelating microspheres

Construction of amino-thiol functionalized ion-imprinted chitosan for lead (II) ion removal

Ion-imprinting technique was used to create a lead ion-imprinted sorbent from an amino-thiol chitosan derivative (Pb-ATCS). First, 3-Nitro-4-sulfanylbenzoic acid (NSB) unit's amidized the chitosan, and then the -NO₂-residues were selectively reduced to -NH₂. Imprinting was accomplished by cross-linking with epichlorohydrin and removing the Pb (II) ions from the across-linked polymeric complex formed from the amino-thiol chitosan polymer ligand (ATCS) and Pb (II) ions. The synthetic steps have been investigated by nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR), and the sorbent was tested for its ability to selectively bind Pb (II) ions. The produced Pb-ATCS sorbent had a maximum capacity of roughly 300 mg/g, and it showed a greater affinity for the Pb (II) ions than the control NI-ATCS sorbent particle. The pseudo-2nd-order equation was also consistent with the adsorption kinetics of the sorbent, which were quite rapid. This demonstrated that metal ions were chemo-adsorbed onto the Pb-ATCS and NI-ATCS solid surfaces via coordination with the introduced amino-thiol moieties.

Design of ion-imprinted cellulose-based microspheres for selective recovery of uranyl ions

Herein, cellulose was selected as the raw material for the production of sorbent microspheres for the selective separation of uranyl (UO₂²⁺) ions by ion-imprinting technique due to their low cost, biodegradability, and renewability. To begin, an amidoxime cellulosic derivative (AOCE) is synthesized by a Michael addition followed by an amidoximation reaction, both of which are homogeneous reactions. In the end, microspheres of ion-imprinted U-AOCE sorbent were made by mixing the developed AOCE derivative with UO₂²⁺, crosslinking the UO₂²⁺ polymer complex with glyoxal, and eluting the coordinated ions with H⁺/EDTA. U-AOCE smartly recognized the target ions for fitting the cavities generated during the UO₂²⁺-imprinting process, resulting in a much greater adsorption capacity of 382 ± 1 mg/g and enhanced adsorption selectivity for UO₂²⁺. A pseudo-second-order model fit the data well in terms of kinetics, while the Langmuir model adequately explained the isotherms, indicating chemisorption and adsorption via UO₂²⁺ chelation. The coordination between UO₂²⁺ and both the -NH₂ and -OH groups of the amidoxime units is the primary adsorption process, as shown by NMR, XPS, and FTIR studies. For UO₂²⁺ biosorption from aqueous effluents, the results of this study deliver new guidance for the design of biosorbents with high removal capability and excellent selectivity.

Intercalation of salicylaldoxime into layered double hydroxide: ultrafast and highly selective uptake of uranium from different water systems via versatile binding modes

We report the first example of MgAl layered double hydroxide intercalated with salicylaldoxime (SA-LDH) which exhibits excellent uranium (U(VI)) capture performance. In U(VI) aqueous solutions, the SA-LDH shows a tremendous maximum U(VI) sorption capacity (q_m^U) of 502 mg·g^-1, surpassing most known sorbents. For the aqueous solution with an initial U(VI) concentration (C₀^U) of ∼ 10 ppm, ≥99.99 % uptake is achieved in a wide pH range of 3-10. At C₀^U ∼ 20 ppm, >99 % uptake is reached within only 5 min, and pseudo-second-order kinetics rate constant (k₂) of 44.9 g·mg^-1·min^-1 reaches the record value, placing the SA-LDH amongst the fastest U adsorbing materials reported to date. In contaminated seawater with 35 ppm of U while highly concentrated metal ions of Na⁺, Mg²⁺, Ca²⁺, and K⁺, the SA-LDH still displays exceptionally high selectivity and ultrafast extraction for UO₂²⁺, giving >95 % uptake of U(VI) within 5 min, and the k₂ value of 0.308 g·mg^-1·min^-1 for seawater surpasses most reported values for aqueous solutions. Versatile binding modes toward U by SA-LDH, including complexation (UO₂²⁺ with SA^- and/or CO₃^2-), ion exchange and precipitation, contribute to the preferable uptake of U at different concentrations. X-ray absorption fine structure (XAFS) analyses demonstrate that one uranyl ion (UO₂²⁺) binds to two SA^- anions and two H₂O molecules forming 8-coordinated configuration. The U coordinates with O atom of the phenolic hydroxyl group and N atom of the -CN-O^- group of SA^-, forming a stable six-membered ring motif, which endows the fast and robust capture of U. The wonderful uranium trapping ability makes the SA-LDH among the best adsorbent used for uranium extraction from various solution systems including seawater.

Plant mediated magnetic nano composite as promising scavenger's radionuclides for the efficient remediation in aqueous medium

The present investigation demonstrates the environment friendly plant mediated green synthesis of magnetic bio composite nanoparticles by the chemical co-precipitation of magnetite phase from aqueous medium. Water contaminated with uranium is one of the most serious environmental issues. This study aims to overcome this issue by effectively adsorbing uranium from water at a pH range of 7. Several studies have recently been published throughout the world that demonstrates uranium adsorption from water, although they have all been conducted in acidic media with pH less than 6. This work addressed that issue, and maximal adsorption was achieved at pH 7 using a synthetic magnetic bio composites sorbent derived from tree bark (Amla). The magnetic bio composites were characterized by FTIR, XRD, FE-SEM, and EDX. The computations of the XRD data indicated that magnetic bio composites have nano composite with an average diameter of around 12.1 nm. This has an adsorption capacity of 121.95 mg g^-1. The correlation regression (r²) coefficients obtained for the various isotherm models indicate that the sorption process conformed to the Langmuir and Temkin models. Thermodynamic studies revealed that the sorption process onto plant mediated magnetic bio material is endothermic and spontaneous, which is significant for reuse and recovery of adsorbed material. A desorption test was also performed to regenerate the material by removing the adsorbed uranium (VI) by HCL with an 84.3% success rate.

Characteristic Aspects of Uranium(VI) Adsorption Utilizing Nano-Silica/Chitosan from Wastewater Solution

A new nano-silica/chitosan (SiO₂/CS) sorbent was created using a wet process to eliminate uranium(VI) from its solution. Measurements using BET, XRD, EDX, SEM, and FTIR were utilized to analyze the production of SiO₂/CS. The adsorption progressions were carried out by pH, SiO₂/CS dose, temperature, sorbing time, and U(VI) concentration measurements. The optimal condition for U(VI) sorption (165 mg/g) was found to be pH 3.5, 60 mg SiO₂/CS, for 50 min of sorbing time, and 200 mg/L U(VI). Both the second-order sorption kinetics and Langmuir adsorption model were observed to be obeyed by the ability of SiO₂/CS to eradicate U(VI). Thermodynamically, the sorption strategy was a spontaneous reaction and exothermic. According to the findings, SiO₂/CS had the potential to serve as an effectual sorbent for U(VI) displacement.

Appreciatively Efficient Sorption Achievement to U(VI) from the El Sela Area by ZrO2/Chitosan

The need to get uranium out of leaching liquid is pushing scientists to come up with new sorbents. This study uses the wet technique to improve the U(VI) sorption properties of ZrO2/chitosan composite sorbent. To validate the synthesis of ZrO2/CS composite with Zirconyl-OH, -NH, and -NH2 for U(VI) binding, XRD, FTIR, SEM, EDX, and BET are used to describe the ZrO2/chitosan wholly formed. To get El Sela leaching liquid, it used 150 g/L H2SO4, 1:4 S:L ratio, 200 rpm agitation speed, four hours of leaching period, and particle size 149–100 µm. In a batch study, the sorption parameters are evaluated at pH 3.5, 50 min of sorbing time, 50 mL of leaching liquid (200 mg/L U(VI)), and 25 °C. The sorption capability is 175 mg/g. Reusing ZrO2/CS for seven cycles with a slight drop in performance is highly efficient, with U(VI) desorption using 0.8 M acid and 75 min of desorption time. The selective U(VI) recovery from El Sela leachate was made possible using ZrO2/CS. Sodium diuranate was precipitated and yielded a yellow cake with a purity level of 94.88%.

Epichlorohydrin and tripolyphosphate-crosslinked chitosan-kaolin composite for Auramine O dye removal from aqueous solutions: Experimental study and DFT calculations

Chitosan (Ch, a natural polymer) and kaolin (K, a natural mineral) composite (Ch-K) was produced with the help of two crosslinkers, epichlorohydrin and tripolyphosphate, and then moulded into uniform beads in tripolyphosphate solution. The synthesis was proved by the analyses involving FT-IR and SEM-EDX. The beads were then used as the natural adsorbent for removal of the auramine O (AO), a frequently-used industrial dye, in aqueous solutions. Adsorbent performance of the Ch-K composite for AO dye molecules was optimized: 500 mg L^-1 at pH 7.5 at 25 °C. The Langmuir model found 0.118 mol kg^-1 for the maximum adsorption capacity of the Ch-K and the D-R isotherm model showed that the nature of the adsorption process was physical. Kinetics of the adsorption could be explained by using both IPD (intraparticle diffusion) and PSO (pseudo second order) models. Thermodynamic parameters demonstrated that the behaviour of the adsorption was an endothermic and spontaneous. The activity of the composite adsorbent was recovered (88%) after the five sequential adsorption/desorption cycles. Supported by experimental findings, the results obtained from in silico modeling at M06-2X/6-31+G (d,p) level helped hypothesise a mechanism for the formation of the Ch-K composite, and shed some light onto the adsorption behaviour of AO dye by assuming several favourable intermolecular interactions.

A chitosan-based composite for adsorption of uranyl ions; mechanism, isothems, kinetics and thermodynamics

The present paper describes a green and cost-effective approach to investigate chitosan-sepiolite (Ch-Sep) composite as an adsorbent for removal of UO₂²⁺ ions in aqueous solution. The Ch-Sep composite was prepared as a beads using with two cross-linking agents: tripolyphosphate (TPP) and epichlorohydrin (ECH). Their adsorption properties for the removal of UO₂²⁺ ions in aqueous solution by batch experimental conditions were studied. The adsorptive removal processes of UO₂²⁺ ions from aqueous solution were evaluated by Langmuir, Freundlich and Dubinin-Radushkevich isotherm models, and was found to be perfectly fit to the Langmuir model (R² = 0.971). The maximum adsorption capacity was 0.220 mol kg^-1 at 25 °C from Langmuir isotherm model. Adsorption energy was 12.1 kJ mol^-1 indicating that the adsorption process was chemical. The adsorption kinetics followed the pseudo second order and intra particle diffusion models. The thermodynamics parameters of UO₂²⁺ ions removal from aqueous solution was confirmed spontaneous, endothermic and possible at higher temperatures behavior of adsorption process. The adsorption mechanism of UO₂²⁺ ions onto Ch-Sep composite beads was investigated by FT-IR and SEM analysis. These findings revealed the effectiveness and potential of the newly synthesized Ch-Sep composite beads for the removal of UO₂²⁺ ions.

Highly efficient capture of uranium from seawater by layered double hydroxide composite with benzamidoxime

Through swelling/restoration reaction, benzamidoxime (BAO) is introduced into MgAl-LDH interlayers to assemble a new composite of MgAl-BAO-LDH (abbr. BAO-LDH). Wet samples of the BAO-LDH obtained by washing with diverse solvents are present in colloidal state, which facilitates the fabrication of thin film adsorbents convenient for actual application. After drying, the assembled sample exhibits floral morphology composed of thin nanosheets, much different from hexagonal morphology of NO₃^- intercalated MgAl-LDH precursor (NO₃-LDH), demonstrating a phenomenon rarely found in swelling/restoration. The BAO-LDH depicts an extremely large maximum sorption capacity (q_m^U) of 327 mg·g^-1 and ultra-high selectivity for U. At low U concentrations (5-10 ppm), nearly complete capture (~100%) is achieved in a wide pH range of 3-11, while at high U concentrations (110 ppm), quite high U removals (≥93.0%) are obtained at pH = 6-8, meaning perfect suitability for trapping U from seawater. For natural seawater containing trace amounts of U (3.93 ppb) coexisting with high concentration of competitive ions, the BAO-LDH displays significantly high U removal (87%). Complexation between interlayer BAO (N and O as ligands) with UO₂²⁺ and synergistic interactions of LDH layer hydroxyls with UO₂²⁺ contribute to the highly effective uranium capture. All results demonstrate the BAO-LDH is a promising adsorbent applied in seawater uranium extraction and nuclear wastewater disposal.

Ion-Imprinted Polymers: Synthesis, Characterization, and Adsorption of Radionuclides

Growing concern over the hazardous effect of radionuclides on the environment is driving research on mitigation and deposition strategies for radioactive waste management. Currently, there are many techniques used for radionuclides separation from the environment such as ion exchange, solvent extraction, chemical precipitation and adsorption. Adsorbents are the leading area of research and many useful materials are being discovered in this category of radionuclide ion separation. The adsorption technologies lack the ability of selective removal of metal ions from solution. This drawback is eliminated by the use of ion-imprinted polymers, these materials having targeted binding sites for specific ions in the media. In this review article, we present recently published literature about the use of ion-imprinted polymers for the adsorption of 10 important hazardous radionuclides-U, Th, Cs, Sr, Ce, Tc, La, Cr, Ni, Co-found in the nuclear fuel cycle.

Development of highly efficient bundle-like hydroxyapatite towards abatement of aqueous U(VI) ions: Mechanism and economic assessment

The exploration of emergency materials with ultra-fast adsorption rate and great adsorption capability of released U(VI) ions is essentially urgent. The present work successfully fabricated bundle-like hydroxyapatite (B-HAP) microstructures which composed of numerous nanorods by employing a facile and green method. The B-HAP was applied to treat the U(VI) containing wastewater. The abatement of U(VI) by B-HAP was very rapid and the saturated adsorption capacity was superior; over 96.7 % of U(VI) was abated within 5 min, and the maximum adsorption capacity was as high as to 1305 mg/g, signifying the feasibility and effectiveness of this B-HAP in the treatment of uranium-contaminated wastewater due to nuclear accidents. It is worthy to note that other ions in solution exhibited relatively low interference on its performance, indicating that B-HAP has great application potential to capture U(VI) from radioactive-contaminated wastewater as well. The U(VI) removal mechanism by B-HAP was confirmed with results from XRD, FT-IR and XPS. Chernikovite [H₂(UO₂)₂(PO₄)₂·8H₂O] was newly formed after U(VI) abatement by B-HAP. Economic assessment suggested B-HAP and its application on U(VI) abatement were cost-effective. With characteristics of high adsorption rate, large capacity, and strong antijamming ability, B-HAP has great application potential as an emergency treatment material for nuclear accidents.

Carboxymethyl konjac glucomannan mechanically reinforcing gellan gum microspheres for uranium removal

Biosorbents have been a promising adsorbent to remove uranium while their poor mechanical properties prevent them from being widely used in practice. In this study, carboxymethyl konjac glucomannan (CMKGM) was incorporated to gellan gum to form a double-network gel micro spheres (CMKGM/GG-Al) for uranium removal with its mechanical strength fairly being reinforced. The compressive strength of the CMKGM/GG-Al microspheres was about 6 times than that of GG-Ca microspheres we prepared before while the adsorption capacity still be at a better value with the fitting maximum adsorption capacity being of 97.94 mg/g. Its uranium adsorption properties were investigated by considering the influence of pH, the adsorbent dosage, temperature, initial uranium concentration, time and coexisting ions. The adsorption mechanism was also investigated according to the SEM, EDX, FT-IR and XPS data analysis. The isotherm equilibrium data which were best fitted with Langmuir model and the kinetics data which were best fitted with pseudo-second-order model. It was inferred that the adsorption process was mainly the ion-exchange and the coordination with hydroxyl groups on the adsorbent surface and the adsorption process was endothermic and spontaneous. The CMKGM/GG-Al microspheres prepared in this study would be more conducive to practical application for uranium removal.

Fabrication and investigation of gold (III) ion-imprinted functionalized silica particles

Au (III) ion-imprinted mesoporous silica particles (Au-Si-Py) was manufactured by the condensation reaction of (3-Aminopropyl)triethoxysilane (AT)and 2-pyridinecarboxaldehyde (Py). The obtained AT-Py Schiff base ligand was then coordinate with the template gold ions and the polymerizable gold-complex was allowed to gel in presence of tetraethoxysilane (TEOS) and then the coordinated gold ions were leached out of the obtained silica matrix using acidified thiourea solution. During the synthetic steps, the obtained materials were investigated utilizing advanced instrumental and spectral methods. Moreover, the morphological structure of both Au (III) ions imprinted Au-Si-Py and non-imprinted NI-Si-Py silica particles were visualized using scanning electron microscope (SEM). Various adsorption experiments had been carried out using both Au-Si-Py and NI-Si-Py to examine their potential for selective extraction of gold ions under different conditions.

Synthesis and characterization of novel ion-imprinted guanyl-modified cellulose for selective extraction of copper ions from geological and municipality sample

The new ion-imprinted guanyl-modified cellulose (II.Gu-MC) was prepared for the separation and determination of Cu (II) ions in different real samples. Several techniques such as Fourier Transform Infrared (FT-IR), scanning electron microscope (SEM), thermal analysis, potentiograph and elemental analysis have been utilized for the characterization of II.Gu-MC. The adsorption behavior of the ion imprinted polymer (II.Gu-MC) was evaluated and compared to the non ion-imprinted polymer (NII.Gu-MC) at the optimum conditions. The selectivity and the adsorption capacity were greatly enhanced by using the ion-imprinted polymer, indicating its validation for the separation and determination of Cu²⁺ ions in different matrices. The adsorption capacity by chelating fibers II.Gu-MC & NII.Gu-MC agreed with the second-order model, and the sorption-isotherm experiments revealed best agreement with Langmuir model. The adsorption capacity of II.Gu-MC and NII.Gu-MC were 115 and 55 mg·g^-1, respectively. The II.Gu-MC was successfully employed for the selective separation and determination of Cu(II) ions with high accuracy.

Synthesis and characterization of a new ion-imprinted polymer for the selective separation of thorium(iv) ions at high acidity

A new ion-imprinted polymer (IIP), which was synthesized with bis(2-methacryloxyethyl) phosphate as functional ligand and Th⁴⁺ as a template ion, can be used in high acidity environment.

Coumarin-modified microporous-mesoporous Zn-MOF-74 showing ultra-high uptake capacity and photo-switched storage/release of U(VI) ions

Driven by an energy crisis but consequently puzzled by various environmental problems, uranium, as the basic material of nuclear energy, is now receiving extensive attentions. In contrast to numerous sorbents applied in this field, metal-organic framework (MOFs), as a renovated material platform, has only recently been developed. How to improve the adsorption capacity of MOF materials towards U(VI) ions, as well as taking advantage of the nature of these MOFs to design photo-switched behaviour for photo-triggered storage/release of U(VI) ions are at present urgent problems and great challenges to be solved. Herein, we show a simple and facile method to target the goal. Through coordination-based post-synthetic strategy, microporous- mesoporous Zn-MOF-74 was easily functionalized by grafting coumarin on coordinatively unsaturated Zn(II) centers, yielding a series of coumarin-modified Zn-MOF-74 materials. The obtained samples displayed ultra-high adsorption capacity for U(VI) ions from water at pH value of 4 with maximum adsorption capacities as high as 360 mg/g (the record value in MOFs) and a remarkable photo-switched capability of 50 mg/g at pH value of 4. To the best of knowledge, and in contrast to the well-known photo-switched behaviour towards CO2, dye (propidium iodide), as well as fluorescence observed in MOFs, this is the first study that shows a photo-switched behaviour towards radioactive U(VI) ions in aqueous solution.

Synthesis and characterization of amidoxime modified calix[8]arene for adsorption of U(vi) in low concentration uranium solutions

Amidoxime-calix[8]arene compound was synthesized for the first time and exhibited high adsorption capacity towards uranium in low concentration solutions.

Highly selective monitoring of metals by using ion-imprinted polymers

Ion imprinting technology is one of the most promising tools in separation and purification sciences because of its high selectivity, good stability, simplicity and low cost. It has been mainly used for selective removal, preconcentration, sensing and few miscellaneous fields. In this review article, recent methodologies in the synthesis of IIPs have been discussed. For several applications, different parameters of IIP including complexing and leaching agent, pH, relative selectivity coefficient, detection limit and adsorption capacity have been evaluated and an attempt has been made to generalize. Biomedical applications mostly include selective removal of toxic metals from human blood plasma and urine samples. Wastewater treatment involves selective removal of highly toxic metal ions like Hg(II), Pb(II), Cd(II), As(V), etc. Preconcentration covers recovery of economically important metal ions such as gold, silver, platinum and palladium. It also includes selective preconcentration of lanthanides and actinides. In sensing, various IIP-based sensors have been fabricated for detection of toxic metal ions. This review article includes almost all metal ions based on the ion-imprinted polymer. At the end, the future outlook section presents the discussion on the advancement, corresponding merits and the need of continued research in few specific areas. Graphical Abstract IIPs for the selective monitoring of metals.