Adsorption mechanisms of thallium(I) and thallium(III) by titanate nanotubes: Ion-exchange and co-precipitation

Synthesis of porous carbon derived from coal tar residue via bimetallic salt activation for effective and selective adsorption of thallium(I)

As a highly toxic rare metal, the removal of thallium (Tl) from wastewater has been widely investigated, and adsorption is considered one of the most promising treatment technologies for Tl-containing contaminated water because of its cost-effectiveness, convenience, and high efficacy. In this work, coal tar residue (CTR)-based porous carbon was synthesized through K2FeO4 activation, and applied in adsorbing Tl(I). K2FeO4 could synergistically produce porosity and load iron oxide on the produced porous carbon surface because of the catalytic cracking and oxidative etching during the activation of CTR. The adsorbent was synthesized at 800 ℃ with a mass ratio of K2FeO4/CTR being 3 (PC3-800) showed optimal Tl(I) adsorption performance. The removal efficiency and distribution coefficient of PC3-800 were above 95 % and 104 mL/g, respectively, in a wide pH range (4-10). Furthermore, the selection and reusability of PC3-800 were favorable. The adsorption was a spontaneous, exothermic, and entropy increase process. The adsorption process was dominated by electrostatic attraction, surface complexation, and surface oxidation. The results suggested that removing Tl(I) from contaminated water via CTR-based porous carbon was feasible.

A Metatitanic Acid Particulate Xerogel: Green Synthesis, Structure Determination, and Detailed Characterization

The manuscript focuses on an original method of preparation of metatitanic acid when only environmentally safe base substances are used in the synthesis process. The synthesis is based on the reaction of solid titanyl sulfate in an aqueous solution of sodium hydroxide. This method allows for (i) a full preservation of the morphology of the starting titanyl sulfate and (ii) a preparation of metatitanic acid substances with specific parameters. This can be achieved via a precise control of the alkali metal/titanyl sulfate ratio resulting in substances with varying contents of alkali metals or even sulfate anions. The prepared metatitanic acid then also contains very small weakly crystalline particles (2-3 nm) and forms pseudomorphic aggregates whose shape and dimensions correspond to those of the starting titanyl sulfate. These aggregates exhibit regular nanoporosity with a high surface area of up to 500 m2·g-1, have no tendency to form colloids, and are mechanically highly resistant even by high-energy ultrasound. The characterization of the resulting products is done via their chemical composition and methods of structural analysis, as well as by electron microscopy and local analysis. The mechanism of product formation is discussed based on the structure of the precursor, including the so far unknown structure of metatitanic acid.

Selective removal of thallium from water by MnO2-doped magnetic beads: Performance and mechanism study

Aqueous thallium has posed an increasing threat to environment as human's intensified activities in mining, refining, process and discharge. Remediation on thallium pollution has been of up-most importance to water treatment. In present work, MnO2 and magnetic Fe3O4 have been implanted to sodium alginate (SA) in presence of carboxyl methyl cellulose (CMC), and the resultant beads consisted of SA/CMC/MnO2/Fe3O4 were characterized. The materials were applied to treatment of Tl-contaminated water as adsorbent in lab. The removal results revealed that the adsorption capacity reached 38.8 mg (Tl)·g (beads)-1 and almost 100 % removal efficiency was achieved. The residual Tl was below 0.1 μg·L-1, meeting the discharge standard regulated in China. The kinetic adsorption was better described as a pseudo-second-order and three-step intra-particle diffusion model. Freundlich isotherm was well fitted the experimental data. The absorbent shown an excellent competitive specificity (KTl/M: ∼104!) over common hazardous ions Cu2+, Cd2+, Co2+, Pb2+ and Cr3+, as well as naturally abundant K+ and Na+ (KTl/M: 10-102) in mimic environmental conditions. Regeneration and reusability of the absorbent was also verified by five absorption-desorpotion cycles. XPS results revealed that a redox reaction between Mn4+ with Tl+, and an ion exchange of H+ (-O-Fe) and Tl+ were assumed to be main process for the specific capturing. This study provided an efficient SA/CMC/MnO2/Fe3O4 composite beads that could be a promising adsorbent for Tl-polluted water treatment.

Mn/Ce@HKUST-1 for Efficient Removal of Gaseous Thallium: Insights from Kinetic and Experimental Studies

Gaseous thallium (Tl) pollution events, primarily caused by non-ferrous mineral refineries and fossil fuel combustion, have increased over the past few decades. To prevent gaseous Tl distribution from flue gas, MnO2/CeO2@HKUST-1 (MCH) was synthesized and found to achieve a gaseous Tl(I) removal level of up to 90% at 423 K, a weight hourly space velocity (WHSV) of 2000 h-1/mL with an Mn dose of 10%, maintained over 10 h. The best Mn/Ce ratio was found to be 9:1. To further investigate surface kinetic behavior, four commonly used kinetic models were applied, including the Eley-Rideal (ER) model, Langmuir-Hinshelwood (LH) model, Mars-van Krevelen (MVK) model, and pseudo-first-order (PFO) model. While the ER and LH models had the slightest deviation, the MVK model was the most reliable. The CatMAP software was also used to match the simulation deviation. This work demonstrated the Tl removal mechanism and provided insights into the accuracy of kinetic models on minor-radius heavy metal. Thus, this research may help promote the design of reactors, heavy metal removal rates, and flue gas purification technology selection.

Recent Advances in Thallium Removal from Water Environment by Metal Oxide Material

Thallium is widely used in industrial and agricultural development. However, there is still a lack of systematic understanding of its environmental hazards and related treatment methods or technologies. Here, we critically assess the environmental behavior of thallium in aqueous systems. In addition, we first discuss the benefits and limitations of the synthetic methods of metal oxide materials that may affect the practicality and scalability of TI removal from water. We then assess the feasibility of different metal oxide materials for TI removal from water by estimating the material properties and contaminant removal mechanisms of four metal oxides (Mn, Fe, Al, and Ti). Next, we discuss the environmental factors that may inhibit the practicality and scalability of Tl removal from water. We conclude by highlighting the materials and processes that could serve as more sustainable alternatives to TI removal with further research and development.

Effect of montmorillonite biochar composite amendment on thallium bioavailability in contaminated agricultural soils and its mitigated health risk

Little information is available on the effect of clay minerals and biochar composite on the remediation and bioavailability of thallium in agricultural soils. This study thus investigated the influence of montmorillonite biochar composite (Mnt-BC) amendment on the remediation of agricultural soil contaminated artificially by Tl and its potential health risks. Herein, bok choi was cultured to estimate the efficiency of soil Mnt-BC amendments through the bioavailability of Tl of the vegetable. Results showed that Tl bioavailability was significantly reduced in Mnt-BC-amended soils, mainly ascribed to the elevated soil pH and other improved soil properties of high functional groups (-OH, -COOH), negative charges, and exchangeable cations after amendment. Specifically, the highest immobilization efficiency of Tl in soils was observed in 2.5% treated soils with 79.11%, while in plant leaves the highest reduction of Tl was estimated to be 75.1% compared to the control treatment. Hence, the amendment dosage improved the immobilization of Tl in soil and subsequently reduced Tl uptake by the vegetable. Furthermore, from target hazard quotient (THQ) estimation, Mnt-BC amendment can lower the potential health risk while consuming such cultured bok choi in Tl-contaminated soils. Considering the environmental friendliness and high efficiency of Mnt-BC, it could be used as a potential soil amendment to remediate agricultural soils contaminated by Tl.

Zwitterionic ammonium-sulfonato grafted cellulose for efficient thallium removal and adsorption mechanism study

Thallium (Tl) has posed serious impacts on human being concerning increasingly serious pollution in aqueous environments. However, little information on removal method than conventional heavy metals have been available. In the present work, zwitterionic N-(3-sulfonato-1-propyl)-N,N-dimethylammonium grafted cellulose fibre (DMAE-PS) has been fabricated. The chemical component, thermal stability and surface properties of as-prepared materials are identified by FT-IR, elemental analysis, TGA, XRD, BET and SEM. DMAE-PS is shown to be very efficient for removing Tl(I) from water samples with a loading capacity of 274.7 mg (Tl(I))·g^-1 (DMAE-PS)_, representing one of the best performances among bio-mass derived materials. The adsorption is consistent with the Freundlich model following a pseudo-second order (K₂ = 4.36 × 10^-4 g·mg^-1·min^-1, R² = 0.999) and two-step intra-particle diffusion kinetics. The selectivity towards Tl(I) is also remarkably, 1-2 orders (distribution ratio K_Tl/M = 14.85-289.29) of magnitude larger than competing metals (Zn²⁺, Cr³⁺, Mn²⁺, Cu²⁺ and Cd²⁺). The SEM, XPS and UV-visible spectrum collectively reveal that -SO₃^--Tl(I) ionic interaction is probably the main driving force for specific adsorption, which shows a high stability against pH variation. The fabricated DMAE-PS is a sustainable bio-adsorbent with synthetic availability, high removing capacity and strong selectivity, therefore, potentially feasible in treatment of Tl(I) polluted environmental samples.

Effective Thallium(I) Removal by Nanocellulose Bioadsorbent Prepared by Nitro-Oxidation of Sorghum Stalks

Thallium(I) (Tl(I)) pollution has become a pressing environmental issue due to its harmful effect on human health and aquatic life. Effective technology to remove Tl(I) ions from drinking water can offer immediate societal benefits especially in the developing countries. In this study, a bio-adsorbent system based on nitro-oxidized nanocellulose (NOCNF) extracted from sorghum stalks was shown to be a highly effective Tl(I) removal medium. The nitro-oxidation process (NOP) is an energy-efficient, zero-waste approach that can extract nanocellulose from any lignocellulosic feedstock, where the effluent can be neutralized directly into a fertilizer without the need for post-treatment. The demonstrated NOCNF adsorbent exhibited high Tl(I) removal efficiency (>90% at concentration < 500 ppm) and high maximum removal capacity (Qm = 1898 mg/g using the Langmuir model). The Tl(I) adsorption mechanism by NOCNF was investigated by thorough characterization of NOCNF-Tl floc samples using spectroscopic (FTIR), diffraction (WAXD), microscopic (SEM, TEM, and AFM) and zeta-potential techniques. The results indicate that adsorption occurs mainly due to electrostatic attraction between cationic Tl(I) ions and anionic carboxylate groups on NOCNF, where the adsorbed Tl(I) sites become nuclei for the growth of thallium oxide nanocrystals at high Tl(I) concentrations. The mineralization process enhances the Tl(I) removal efficiency, and the mechanism is consistent with the isotherm data analysis using the Freundlich model.

Removal of Thallium from Aqueous Solutions by Adsorption onto Alumina Nanoparticles

Thallium (I) was removed from aqueous solution by using gamma-alumina nanoparticles (γANPs) materials as nano adsorbents. Varied experimental conditions such as adsorbent dose, agitation time, initial concentration, pH, and temperature effects were carried out in batch conditions in view of the optimization of thallium (I) adsorption and the identification of the adsorption mechanisms in the system γANPs-Tl. The pH effect indicated a remarkable increase in the quantity of Tl(I) removed for pH values ranging from 4 to 8, an almost constant magnitude for pH values between 8 and 10, and a decrease for pH values above 10. Considering an initial Tl(I) concentration of 20 µg/L and an adsorbent dose of 1 g/L at a pH value of 8.5, the removal was achieved at 95.12 ± 0.02% efficiency. The pseudo-second-order kinetics and the Freundlich isotherm perfectly described the adsorption mechanism. The process of thallium (I) adsorption reaction, as highlighted by thermodynamic investigations, was found to be spontaneous and exothermic with coexistence of physisorption and chemisorption with a dominance of physisorption. The diffusion model predicted multi-linearity, suggesting an involvement of surface spread and intraparticle diffusion in the sorption process. Thallium removal was effective by using γANPs as nano adsorbents.

New Approach for Trace Thallium Removal in High Purity Ammonium Rhenate Solution by P204 Extraction

Thallium (Tl) is an extremely toxic rare metal to the eco-environment. Trace thallium impurity in ammonium perrhenate is harmful to the high-temperature mechanical properties of rhenium metal used for aeroengine single crystal blade. The di(2-ethylhexyl) phosphoric acid (P204) extraction to remove thallium in ammonium perrhenate solution without additive was innovatively proposed. The migration behavior of trace thallium with the concentration of P204, saponification degree and organic/aqueous phase (O/A) ratio, distribution law of thallium in the extraction system of P204, and mechanism of thallium removal were revealed. It was found Tl removal was rapidly increased to 98.5%, at conditions of P204 0.75 mol/L saponified 70% by ammonia, Tl 3.27 mg/L, O/A 1:1, T 298.15 ± 2 K, 250 rpm, and 3 min. McCabe-Thiele Tl extraction equilibrium isotherms indicates Tl concentration of raffinate less than 18.7 μg/L, a theoretical extraction of two stages and a theoretical stripping of two stages are required when both O/A work lines were at 1.0. Therefore, the method of the P204 solvent extraction system can effectively extract Tl in the forms of TlA(org), TlA3(org), TlOHA2(org), and Tl(OH)2A(org). Meanwhile, the new approach can be a promising process for ammonium rhenate refining.

Insights into the synergistic removal mechanisms of thallium(I) by biogenic manganese oxides in a wide pH range

The behavior and mechanism of thallium (Tl) adsorption by biogenic manganese oxides (BMnOx) are poorly understood. In this study, BMnOx was applied for Tl(I) removal from aqueous solution, and the adsorption interactions were systematically revealed for the first time. BMnOx was successfully prepared with high productivity by effectively oxidizing Mn(II) with a manganese oxide bacterium in an optimal Mn(II) concentration range of 4.0-28 mg/L. Compared with other adsorbents, the prepared BMnOx achieved high Tl(I) adsorption capacity over a wide pH range from 3.0 to 9.0 and high humic acid (HA) concentration (40 mg/L) interference. The experimental results were well depicted by pseudo-second-order kinetics and the Langmuir isotherm model, indicating that chemisorption played the dominant role during the adsorption process. The adsorption mechanisms were verified as synergetic interactions of oxidation-precipitation, electrostatic attraction, ion exchange and surface complexation. X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) results suggested that 19.46% of the highly toxic Tl(I) was transformed into the much less toxic product Tl₂O₃ after adsorption onto BMnOx. This study provides theoretical guidance for high-concentration Tl(I) decontamination from groundwater by biogenic manganese oxides.

Potential application of Fusarium fungal strains (Fusarium sp. FP, Arthrinium sp. FB, and Phoma sp. FR) for removal of Tl (I) ions from water

Water pollution caused by heavy metals poses a serious threat to the ecosystem and human health. Among the various treatment techniques for water remediation, adsorption is an efficient method due to its high capacity, low cost, and simplicity. Thallium (Tl) is highly toxic to mammals and its removal from water is gaining increasingly prominent attention. In this study, three fungal strains (Fusarium sp. FP, Arthrinium sp. FB, and Phoma sp. FR) were tested for removal of Tl (I) from aqueous solutions and showed excellent removal performance. The prepared inactive fungal strains were characterized by XRD, FT-IR, SEM, and XPS analyses. The effects of pH, contact time, biomass dosage, and reaction temperature on the removal efficiency of Tl (I) were systematically investigated. The results indicated that the adsorption isotherm data fit well with the Langmuir model, and the pseudo-second-order model was more consistent with the kinetic data description. The maximum adsorption capacity of the fungal strain (Fusarium sp. FP, Arthrinium sp. FB, and Phoma sp. FR) for Tl (I) was found to be 94.69 mg/g, 66.97 mg/g, and 52.98 mg/g, respectively. The thermodynamic data showed that the sorption process was spontaneous and endothermic. The present study showed that the inactive fungal strains could be a promising adsorbent material for Tl (I) removal.

Adsorption of Congo red by fibrous xonotlite prepared from waste silicon residue

Fibrous xonotlite was synthesized under the conditions of Na₂SiO₃ concentration of 0.05 mol·L^-1, molar ratio of Si/Ca of 1:1, temperature of 220 °C and time of 9 h. It is worth pointing out that the Na₂SiO₃ solution as raw material was obtained from silicon residue through several procedures. The fibrous xonotlite exhibits excellent adsorption capacity for Congo red. 50 mL solution of Congo red with the concentrations of 100, 150 and 200 mg·L^-1 can be almost completely adsorbed by 30 mg of fibrous xonotlite within 10 min, and the adsorption ratios are 94.05%, 95.50% and 94.14%. The Langmuir model describes the adsorption well, indicating the adsorption is monolayer. The adsorption kinetics follows the pseudo-second-order model. The calculated maximum adsorption capacity of fibrous xonotlite for Congo red is 574.71 mg·g^-1 at room temperature. Fibrous xonotlite is a potential efficient adsorbent for Congo red owing to its rapid adsorption, high adsorption capacity and regeneration capacity.

Remediation of noxious wastewater using nanohybrid adsorbent for preventing water pollution

Removal of toxic elements from wastewater effluent has got a lot of attention because of their severe negative effects on human and environmental health. In the past few years, rapid urbanization and industrial activities in developing countries have exacerbated the destruction of the environment. Most of the wastewater effluents are discharged untreated or inadequately treated, which has become a major concern due to its impact on sustainability and the environment. This is imperative to implement, innovative and resourceful wastewater treatment technologies requiring low investment. Among the various treatment technologies, cutting-edge processes in nano-material sciences have recently piqued the interest of scientists. Nanohybrid absorbents have the potential in improving wastewater treatment and increase water supply by utilizing unconventional water resources. Carbon nanotubes, titanium oxide, manganese oxide, activated carbon (AC), magnesium oxide, graphene, ferric oxides, and zinc oxide are examples of nano-adsorbents that are used to eliminate pollutants. This also demonstrated the effective removal of contaminants along with the harmful effects of chemicals, colorants, and metals found in wastewater. The present manuscript examines potential advances in nanotechnology in wastewater treatment for the prevention of water and soil pollution. This systematic review aims to highlight the importance of nanohybrid absorbents treatment technology for wastewater treatment and to explain how nanohybrid absorbents have the potential to revolutionize industrial pollution. There are also other published review articles on this topic but the present review covers an in-depth information on nano-adsorbents and their targeted contaminants.

One-pot synthesis of magnetic Prussian blue for the highly selective removal of thallium(I) from wastewater: Mechanism and implications

Thallium (Tl) often enters the environment via mineral exploitation and utilization. The main restriction of Tl removal is the interference of high concentrations of coexisting ions in wastewater, therefore, enhancing the selectivity for Tl is essential to its treatment. Magnetic Prussian blue particles (Fe₃O₄@PB), an ion-sieving material with an open structure, were synthesized through a "one-pot" method at room temperature for the highly selective removal of Tl⁺. The removal percentage of Tl⁺ was over 92% even when the concentration of coexisting ions (e.g. Zn²⁺, Cd²⁺, Cu²⁺, and Pb²⁺) were 10,000 times higher than the initial concentration of Tl⁺. The maximal experimental removal capacity was 528 mg Tl/g Fe₃O₄@PB, and the removal percentage remained steady at pH 3-10. The high selectivity of Fe₃O₄@PB for Tl⁺ is attributed to the fact that hydrated Tl⁺ has a smaller hydrated diameter and a lower hydration free energy than other coexisting ions, while the rapid adsorption kinetics of Tl⁺ results from the negative surface charge and the network of nanocapillaries of the Fe₃O₄@PB. Overall, a new low-cost material that is easy to synthesize and has superior Tl⁺ removal capacity with extremely high selectivity for Tl⁺ was obtained for effective magnetic removal of thallium from wastewater.

Highly efficient removal of thallium(I) by facilely fabricated amorphous titanium dioxide from water and wastewater

In this study, amorphous hydrous titanium dioxide was synthesized by a facile precipitation method at room temperature, aiming to effectively remove thallium(I) from water. The titanium dioxide prepared using ammonia as precipitant (TiO2I) is more effective for thallium(I) uptake than the one synthesized with sodium hydroxide (TiO2II). The TiO2 obtained particles are amorphous, aggregates of many nanoparticles and irregular in shape. The thallium(I) uptake increases with the rise of solution pH value. Under neutral pH conditions, the maximal thallium(I) adsorption capacities of TiO2I and TiO2II are 302.6 and 230.3 mg/g, respectively, outperforming most of the reported adsorbents. The amorphous TiO2 has high selectivity towards thallium(I) in the presence of multiple cations such as K+, Ca2+, Mg2+, Zn2+ and Ni2+. Moreover, the TiO2I is efficient in removing thallium(I) from real river water and mining wastewater. Additionally, the spent TiO2I can be regenerated using hydrochloric acid solution and reused. The Tl(I) adsorption is achieved via replacing the H+ in hydroxyl group on the surface of TiO2 and forming inner-sphere surface complexes. Owing to its high efficiency, facile synthesis and environmental friendliness, the TiO2I has the potential to be used as an alternative adsorbent to remove Tl(I) from water.

Recent Progress on Nanomaterial-Based Membranes for Water Treatment

Nanomaterials have emerged as the new future generation materials for high-performance water treatment membranes with potential for solving the worldwide water pollution issue. The incorporation of nanomaterials in membranes increases water permeability, mechanical strength, separation efficiency, and reduces fouling of the membrane. Thus, the nanomaterials pave a new pathway for ultra-fast and extremely selective water purification membranes. Membrane enhancements after the inclusion of many nanomaterials, including nanoparticles (NPs), two-dimensional (2-D) layer materials, nanofibers, nanosheets, and other nanocomposite structural materials, are discussed in this review. Furthermore, the applications of these membranes with nanomaterials in water treatment applications, that are vast in number, are highlighted. The goal is to demonstrate the significance of nanomaterials in the membrane industry for water treatment applications. It was found that nanomaterials and nanotechnology offer great potential for the advancement of sustainable water and wastewater treatment.

Development of L-cysteine sensor based on thallium oxide coupled multi-walled carbon nanotube nanocomposites with electrochemical approach

Here, Nanocomposites of thallium oxide doped multi-walled carbon nanotube (Tl2O.MWCNT NCs) were prepared by utilizing the wet-chemical method (WCM) in an alkaline phase at low temperature. Different optical procedures (FTIR: Fourier Transform Infra-Red Spectroscopy, XRD: Powder X-ray diffraction, FESEM: Field-Emission Scanning Electron Microscopy, XEDS: X-ray Electron Dispersive Spectroscopy, TEM: Tunneling Electron Microscopy, and XPS: X-ray photoelectron spectroscopy) were used to fully characterize (Optical, structural, crystalline, morphological, and elemental etc.) of the prepared Tl2O.MWCNT NCs. Modification of the thin-layer with NCs onto glassy carbon electrode (GCE) is prepared and applied for the enzyme-free detection of selective and sensitive L-cysteine by electrochemical approach. Using a reliable current-voltage approach, analytical sensing indexes such as sensitivity, LDR, LOD, LOQ, durability, and interference were assessed by fabricated sensor probe (GCE/Tl2O.MWCNT NCs/CPM) in selective detection of L-cysteine in a room condition, whereas nafion was used as conducting polymer matrix (CPM) during the fabrication of GCE with NCs. L-cysteine calibration plot was found to be linear over an extensive range of concentration. The calibration curve was used to calculate the sensing parameters such as sensitivity (316.46 pAμM-1cm-2), LOD down to (~18.90 ± 1.89 pM), and LOQ (63.0 pM) of the prepared sensor. The use of a simple WCM to validate the Tl2O.MWCNT NCs is a good approach for developing a NCs-based sensor for enzyme-free biomolecule identification and detection in the biomedical and health care fields in a broad scale. This proposed sensor (GCE/Tl2O.MWCNT NCs/CPM) is used to detect selective L-cysteine in real biological samples such as human, mouse, and rabbit serum and found acceptable and satisfactory results.

Hydrothermally synthesized titanate nanomaterials for the removal of heavy metals and radionuclides from water: A review

Hazardous heavy metals and radionuclides in water and wastewater are of drastic concern owing to their detrimental impacts on the organisms as well as the circumambient ecosystem. To remove them as much as we can, both technique and materials were studied in the past years. The adsorption technique as superior water remediation method with the simplicity of design, environmental friendliness and high efficiency was well established. Consequently, it is practically important to explore advanced and economically feasible absorbents for removing these poisonous pollutants from aqueous solutions. So far, large numbers of experiments proved hydrothermally synthesized titanate nanomaterials (TNMs) could be a prospectively excellent adsorbent extracting heavy metals and radionuclides from water due to the high specific surface area, tunable pore size, abundant surface active sites, favorable hydrophilic properties. The objective of this work is to give an overview of hydrothermal synthesis, adsorption performance of TNMs for heavy metals and radionuclides, as well as the various influencing factors for water purification. It comprehensively reviews the structural changes and regenerability of TNMs after adsorption, and different modification methods adopted for improving removal capacity. Additionally, it uniquely highlights the efficient decontamination of the pollutants through a synergistic effect of adsorption and photocatalysis by TNMs. This review provides detailed information for the development, application, and research challenges faced by hydrothermally synthesized TNMs for the removal of heavy metals and radionuclides from aqueous solutions, which will serve as a reference guide for scientists in related fields.

Thallium Use, Toxicity, and Detoxification Therapy: An Overview

Thallium (Tl) is released into the environment, where is present at very low levels, from both natural and anthropogenic sources. Tl is considered as one of the most toxic heavy metals; it is a non-essential metal, present in low concentrations in humans. Tl toxicity causes dermatological and gastrointestinal diseases and disorders of the nervous system, and may even result in death. Many isotopes of Tl exist, with different uses. One of the isotopes of this metal (201Tl) is used in cardiovascular scintigraphy and for the diagnosis of malignant tumors such as breast or lung cancer and osteosarcoma bone cancer. Many Tl compounds are tasteless, colorless, and odorless. Due to these characteristics and their high toxicity, they have been used as poisons in suicides and murders for criminal purposes, as well as instances of accidental poisoning. Impaired glutathione metabolism, oxidative stress, and disruption of potassium-regulated homeostasis may play a role in the mechanism of Tl toxicity. Solanum nigrum L. and Callitriche cophocarpa have been suggested as promising agents for the phytoremediation of Tl. In addition, macrocyclic compounds such as crown ethers (18-crown-6) are good candidates to absorb Tl from wastewater. Through this review, we present an update to general information about the uses and toxicity of Tl. Furthermore, the attention is focused on detoxification therapies.

Thallium(I) Salts: New Partners for Calix[4]pyrroles

Calix[4]pyrrole 1 can form host-guest complexes with certain thallium salts, for example, TlF, not only in the gas phase but also in solution and in the solid state. The complexation of TlF by calix[4]pyrrole 1 was found to promote self-assembly and the formation of well-defined and highly ordered fibrous supramolecular morphologies, as revealed by polarizing microscopy and scanning electron microscopy. The findings reported here serve to broaden the scope of cationic substrates that may be complexed as ion pairs by calix[4]pyrrole receptors while setting the stage for the development of new hosts for thallium(I) salts.

Highly-efficient and easy separation of hexahedral sodium dodecyl sulfonate/δ-FeOOH colloidal particles for enhanced removal of aqueous thallium and uranium ions: Synergistic effect and mechanism study

Thallium (Tl) and uranium (U) contaminants pose serious threats to the ecological environment and human health. In this research, a cost-effective feroxyhite (δ-FeOOH) dispersed with sodium dodecyl sulfonate (SDS) was prepared and a series of experiments were optimized to explore the removal mechanism of Tl⁺ and UO₂²⁺ from the effluent. The SDS/δ-FeOOH exhibited highly dispersed colloidal particles and showed significantly enhanced adsorption performance on the removal of Tl and U in the presence of H₂O₂ and pH of 7.0. Equilibrium uptakes of 99.5% and 99.7% were rapidly achieved for Tl⁺ and UO₂²⁺ within 10 min, respectively. The Freundlich isotherm model fitted well with the adsorption data of Tl and U. The maximum isotherm sorption capacity of SDS/δ-FeOOH for Tl⁺ and UO₂²⁺ was 182.9 and 359.6 mg/g, respectively. The sorption of Tl followed the pseudo-second-order kinetic model, whereas the sorption of U followed the pseudo-first-order kinetic model. The uptake of Tl and U by SDS/δ-FeOOH was notably inhibited at Na⁺, K⁺ concentrations over 5.0 mM, and a high content of dissolved organic matter (over 0.5 mg/L). The mechanistic study revealed that ion exchange, precipitation, and surface complexation were main mechanisms for the removal of Tl and U. The findings of this study indicate that stabilizer dispersion may serve as an effective strategy to facilitate the treatment of wastewater containing Tl and U by using δ-FeOOH.

Highly efficient removal of thallium in wastewater by MnFe2O4-biochar composite

Thallium (Tl), is a highly toxic trace metal in the natural environment. Emerging Tl pollution in waters has gradually become a global concern. However, limited removal technologies are available for Tl-containing wastewater. Herein, MnFe₂O₄-biochar composite (MFBC) was successfully fabricated via coprecipitation method as a novel and efficient adsorbent for treating Tl(I)-contaminated wastewater. It was found that the MFBC, with a specific surface area of 187.03 m²/g, exhibited high performance across a wide pH range of 4-11, with the superior Tl(I) removal capacity (170.55 mg/g) based on Langmuir model (pH 6.0, a dosage of 1 g/L). The removal mechanisms included physical and chemical adsorption, ion exchange, surface complexation, and oxidation. This investigation revealed that MFBC is a promising and environmentally friendly adsorbent with a low cost, large specific surface area, magnetic properties, and high efficiency for the removal of Tl(I) from wastewater.

Facile integration of FeS and titanate nanotubes for efficient removal of total Cr from aqueous solution: Synergy in simultaneous reduction of Cr(VI) and adsorption of Cr(III)

In this study, a novel composite composed of iron monosulfide nanoparticles (FeS NPs) and titanate nanotubes (TNTs) was hydrothermally synthesized. Characterizations revealed the encapsulation and homogenous dispersion of FeS NPs into the interlayers of TNTs. Significant performance in removal of aqueous total Cr was acquired by efficient conversion of Cr(VI) to Cr(III) on FeS and simultaneous adsorption of Cr(III) on TNTs. Moreover, the high activity of FeS-TNTs in reduction of Cr(VI) can maintain at high oxicity or alkalinity of its solution. The synergistic effect between FeS and TNTs was derived from sheltering of FeS NPs from their self-aggregation, O₂-oxidation and the affinity of Cr(III) to TNTs. The unique properties, e.g. the solid acidity, the hollow and interlayered configuration of TNTs played important roles in high activity, good stability and reusability of FeS-TNTs.

Fabrication and characterization of magnetically responsive Fe3O4@TiO2 core-shell adsorbent for enhanced thallium removal

Thallium (Tl) contamination in natural waters can pose a severe risk to human health. In this study, a magnetically responsive Fe₃O₄@TiO₂ core-shell adsorbent was developed for the effective removal of thallium(I) from water. The isoelectric point of the adsorbent surface was decreased from 6.0 to 4.8 due to the loading of nano-sized TiO₂, leading to an enhanced electrostatic interaction between the adsorbent and Tl(I) ions in a wider pH range. The Fe₃O₄@TiO₂ magnetic adsorbent exhibited a threefold higher BET specific surface area compared to pristine Fe₃O₄ particles. The kinetics study showed that approximately 82% of the maximum Tl(I) loading amount could be achieved within 30 min at the initial Tl(I) concentration of 8 mg/L and adsorbent dosage of 0.1 g/L. The adsorption of Tl(I) was significantly increased with increasing solution pH. The experimental data was better fitted by the Langmuir and Temkin isotherms than the Freundlich isotherm and the maximum adsorption capacity of the magnetic adsorbent was 101.5 mg/g at pH 7.0. The interference of co-existing cations in the Tl(I) adsorption followed the subsequence: Cu²⁺ > Mg²⁺ > Ca²⁺ > Na⁺. The hydroxyl groups bonded on titanium atoms might play a key role in the uptake of Tl(I) ions. During the adsorption, the Tl(I) ions can be effectively adsorbed on the adsorbent surface via the formation of Ti-O-Tl linkages. Graphical Abstract.

Adsorptive removal of trace thallium(I) from wastewater: A review and new perspectives

Thallium is an emerging pollutant reported in wastewater along with the increasing mining and smelting of thallium-containing ores in recent years. The complete removal of Tl(I) from wastewater is of significant emergency due to its high toxicity and mobility, however, Tl(I) removal is always confronted with numerous technical difficulties because of the extremely low Tl(I) concentration in wastewater and the disturbances of many accompanying impurity ions. Adsorption is currently the most widely used method for Tl(I) removal on industrial scale and varied kinds of adsorbents such as Prussian blue analogues, biosorbents, and metal oxides have been developed. However, the adsorption process of Tl(I) is always affected by the co-existing cations, resulting in low Tl(I) removal efficiency. Recently, the development of a variety of novel adsorbents or ion sensors based on macrocyclic compounds for enrichment and accurate determination of trace Tl(I) in aqueous solutions exhibits great potential for application in Tl(I) removal from wastewater with high selectivity and process efficiency. This paper provides an overview of the adsorption methods for Tl(I) removal from wastewater with emphasis on complexation properties between varied types of adsorbents and Tl(I). Future directions of research and development of adsorptive Tl(I) removal from industrial wastewater are proposed.

Removal of thallium(I) from aqueous solutions using titanate nanomaterials: The performance and the influence of morphology

Thallium (Tl) pollution has attracted environmental attention due to its high toxicity, thus the cleanup of Tl from the environment is of significance. Titanate nanomaterials (TNMs) with different morphologies can be synthesized via a hydrothermal reaction under different conditions but the knowledge of the Tl(I) removal by them is limited. Our results indicated that TNM prepared at 130 °C exhibited a nanotubular appearance and a longer reaction time resulted in the formation of perfect nanotube, while that prepared at 180 °C exhibited a nanowire-like arrangement. The nanotubular and nanowire-like TNMs possessed approximately excellent Tl(I) adsorption capacities, wide pH, and temperature application ranges but different adsorption kinetics. Inorganic ions influenced the Tl(I) removal and the inhibiting effect of heavy metal ions followed the sequence Pb(II) > Cu(II) > Cd(II) > Zn(II). The anti-interference ability and selectivity of wire-like TNMs for Tl(I) removal were higher than those of tubular TNMs. High Tl(I) uptakes of tubular and wire-like TNMs were driven by the electrostatic attraction, ion exchange with Na⁺/H⁺, and complexation with -ONa functional groups in the interlayers and Ti-OH on the surfaces of TNMs as well as microprecipitation; while their adsorption configurations were different. TNMs are promising for potential applications in Tl(I) elimination from wastewater due to the high adsorption capacity and regenerability. This work indicates that TNMs synthesized under different conditions have the similar Tl(I) adsorption performances and the preparation of TNMs used for Tl(I) removal has an undemanding synthesis condition.

Highly efficient removal of thallium(I) from wastewater via hypochlorite catalytic oxidation coupled with adsorption by hydrochar coated nickel ferrite composite

In this study, tannery wastewater was used as carbon source to hydrothermally synthesize magnetic carbon-coated nickel ferrite composite (NiFe₂O₄@C), which was employed as a catalyst for thallium (Tl) oxidation by hypochlorite and simultaneously as an adsorbent for Tl removal from wastewater. Compared with NiFe₂O₄@C adsorption or hypochlorite oxidation alone, the combination of NiFe₂O₄@C and hypochlorite substantially enhanced the rate and efficiency of Tl(I) removal. In addition, this process was highly effective for Tl(I) removal over a wide pH range (6-12). The maximum Tl(I) removal capacity was 1699 mg/g at pH 10, which is the highest one reported so far. Electron spin resonance spectra suggested the formation of hypochlorite-based free radicals induced by the NiFe₂O₄@C composite, which enhanced the Tl(I) oxidation and removal. Oxidation-induced surface precipitation and surface complexation were found to be the main Tl(I) removal mechanisms. Consecutive cyclic regeneration tests implied robust regeneration and reuse performance of the composite. Moreover, it was effective for Tl(I) removal from real industrial wastewater. Therefore, the hypochlorite catalytic oxidation coupled with adsorption by the magnetic NiFe₂O₄@C composite is a promising technique for Tl(I) removal from wastewater. This hybrid process also has great potential for the removal of other pollutants.

Efficient adsorption of europium (III) and uranium (VI) by titanate nanorings: Insights into radioactive metal species

Radioactive wastewater containing high concentration of radionuclides poses severe threats to ecosystem and human health, so efficient removal of these toxic heavy metals is urgently needed. Titanate nanomaterials have been demonstrated good adsorbents for heavy metals due to ion exchange property. In this study, titanate nanorings (TNRs) were synthesized using the facile hydrothermal-cooling method. The TNRs were composed of sodium trititanate, with a chemical formula of Na_0.66H_1.34Ti₃O₇•0.27H₂O and a Na content of 2.38 mmol/g. The TNRs demonstrated sufficient adsorption performance to radionuclides europium (Eu) and uranium (U) ions. Specifically, even at a high initial concentration of 50 mg/L, 86.5% and 92.6% of the two metal ions can be rapidly adsorbed by the TNRs within 5 min, and equilibrium was reached within 60 min at pH 5. The maximum adsorption capacity (Q _max) obtained by the Langmuir isotherm model was 115.3 mg/g for Eu(III) and 282.5 mg/g for uranium U(VI) at pH 5, respectively. The adsorption capacities of the two metals under various water chemical conditions were highly related to their species. Ion exchange between metal cations and Na⁺ in the TNR interlayers was the dominant adsorption mechanism, and adsorption of U(VI) was more complicated because of the co-existence of various uranyl (UO₂ ²⁺) and uranyl-hydroxyl species. The spent TNRs were effectively regenerated through an acid-base or ethylenediamine tetraacetic acid (EDTA) treatment and reused. Considering the large adsorption capacity and quick kinetic, TNRs are promising materials to remove radionuclides in environmental purification applications, especially emergent treatment of leaked radionuclides.

Zero-valent iron-manganese bimetallic nanocomposites catalyze hypochlorite for enhanced thallium(I) oxidation and removal from wastewater: Materials characterization, process optimization and removal mechanisms

Nano zero-valent metals adsorption coupled with advanced oxidation for environmental pollutants removal has been gaining attention recently. In this study, zero-valent iron-manganese (nZVIM) bimetallic nanocomposites were prepared via one-pot borohydride reduction and coupled with hypochlorite (ClO^-) oxidation for enhanced thallium (Tl) removal from wastewater. Amorphous nZVIM nanoparticles were successfully synthesized, with a specific surface area of 106.89 m²/g, and a saturation magnetization of 65.16 emu/g. In comparison with the nZVIM adsorption or ClO^- oxidation alone, the hybrid nZVIM/ClO^- process achieved much faster Tl(I) removal rate over a wide pH range from 6 to 10. Maximum Tl(I) removal capacity was as high as 990.0 mg/g. The oxidation-induced adsorption for Tl(I) removal well followed the pseudo-first kinetic order model. Stable and effective adsorbent regeneration was achieved during the cyclic adsorption-desorption tests. This process also had high resistance to the interference of external cations, can act as an effective pretreatment for Tl(I) removal from the actual saline industrial wastewater. The main mechanisms for Tl(I) removal were found to be oxidation, surface precipitation, pore retention, and surface complexation. The nZVIM coupled with ClO^- approach has great potential for Tl(I) removal from wastewater, and its application in other fields is highly anticipated.

Enhanced thallium(I) removal from wastewater using hypochlorite oxidation coupled with magnetite-based biochar adsorption

The development of efficient and regenerable adsorbent coupled with advanced oxidation for enhanced thallium (Tl) removal has been a recent focus on wastewater treatment. In this study, a magnetite-based biochar derived from watermelon rinds was synthesized and used as a sustainable adsorbent and catalyst for hypochlorite oxidation and removal of Tl(I) from wastewater. The addition of hypochlorite substantially enhanced the Tl(I) removal under normal pH range (6-9). Maximum Tl adsorption capacity of 1123 mg/g was achieved, which is 12.3% higher than the highest value previously reported. The magnetic biochar can be regenerated using 0.1 mol/L HNO₃ solution for elution in only 5 min, with a Tl desorption efficiency of 78.9%. The Tl removal efficiency was constantly higher than 98.5% during five consecutive recycle tests, indicating the effective reuse performance of the adsorbent. Oxidation, surface precipitation, pore retention and surface complexation were the main mechanisms for Tl(I) removal. The re-dissolution of Tl compounds and ion exchange of Tl cations with proton were the main mechanisms for adsorbent regeneration. Given the fast oxidation rate, high adsorption capacity, steady reusability and facile separability, this magnetic biochar-hypochlorite technique is a promising means for Tl(I) removal from wastewater. The catalytic hypochlorite oxidation induced by the magnetic biochar has also great potential to the effective removal of other pollutants.

Extensive removal of thallium by graphene oxide functionalized with aza-crown ether

Thallium (Tl) is a highly toxic heavy metal, and its pollution and remediation in aquatic environments has attracted considerable attention. To reduce or remove Tl pollution in the environment, various strategies have been applied. Graphene oxide (GO) has abundant oxygen-containing functional groups, indicating its high application potential for pollution remediation via methods involving binding to metal ions or positively charged organic molecules or electrostatic interaction and coordination. However, the adsorption of Tl to GO occurs via physical adsorption, for which the adsorption efficiency is low. Therefore, herein, we report a new method to effectively remove Tl pollution in water. We combined GO with aza-crown ether, which enhanced the electronegativity and ability to bind metal ions. The functionalized graphene oxide (FGO) demonstrated high efficiency through a wide pH gradient of 5–10, with a dominant Tl(i) adsorption capacity (112.21 mg g⁻¹) based on the Langmuir model (pH 9.0, adsorbent concentration of 0.8 g L⁻¹). The adsorption of Tl(i) during removal fit a pseudo-second-order kinetic model well. The mechanisms of Tl removal involve physical and chemical adsorption. In summary, our study provides a new method for the detection and treatment of Tl-containing wastewater by using FGO.

Thallium (Tl) is a highly toxic heavy metal, and its pollution and remediation in aquatic environments has attracted considerable attention.

Hydrothermal synthesis of needle-shaped manganese oxide nanoparticle for superior adsorption of thallium(I): characterization, performance, and mechanism study

Thallium as a highly toxic metal element has been listed as one of priority drinking water contaminants. In this study, manganese oxide nanoparticles were synthesized through a simple hydrothermal method and applied for the removal of thallium(I). The adsorbent was composed of numerous needle-like nanorods and had an average volume diameter of 230 nm after heat-drying procedure. The crystal form of adsorbent was determined as α-MnO₂. The adsorbent exhibited a much faster adsorption rate than most of previously reported adsorbent, achieving over 66.4% of equilibrium adsorption capacity in the first 10 min. The adsorption process was found to be highly affected by solution pH and higher than 100 mg/g of adsorption capacity could be obtained in a wide pH range of 6.0-10.0. The isotherm study indicated that the adsorption of Tl(I) on the adsorbent was favorable and governed by a chemisorption process, with the maximum adsorption capacity of 505.5 mg/g at pH 7.0. The adsorption process was confirmed to be thermodynamically spontaneous and endothermic. The presence of Na⁺, K⁺, Mg²⁺, Ca²⁺, and Cu²⁺ cations had certain negative effects on the uptake of Tl(I). Based on the batch experiments and XPS analysis, the deprotonated hydroxyl groups that bonded to manganese atoms worked as the binding sites for the effective removal of Tl(I) ions and no redox reaction occurred during the adsorption process.

Study on adsorption properties and mechanism of thallium onto titanium‑iron magnetic adsorbent

Thallium (Tl) contamination caused by the industrial wastewater leakage has become a serious environmental problem due to thallium's high toxicity. In this study, a novel titanium‑iron magnetic nano-sized adsorbent was synthesized and applied for the effective removal of thallium(I). The physicochemical properties of the adsorbent were investigated by a series of techniques such as scanning electron microscope (SEM), X-ray powder diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). About 83% of equilibrium adsorption capacity could be accomplished within the initial 30 min. The adsorption of Tl(I) was found to be highly dependent on solution pH. The maximum adsorption capacity of Tl(I) was 111.3 mg/g at pH 7.0. The presence of such co-existing cations as Na⁺, Mg²⁺, Ca²⁺ and Cu²⁺ could have a certain influence on the uptake of Tl(I). The adsorption mechanism was proposed as a surface complexation process of Tl(I) ions by binding to deprotonated sites of hydroxyl groups on the adsorbent surface. The prepared magnetic adsorbent would be suitable for effectively treating thallium-containing water due to its promising adsorption ability towards Tl(I) and ease in operation.

Removal of thallium in water/wastewater: A review

The frequent occurrence of thallium (Tl) in surface water has led to the imposition of strict environmental regulations. The need for an overview of effective and feasible technology to remove Tl from water/wastewater has therefore become urgently. This review introduced the current available methods for Tl removal, including adsorption, oxidation-reduction precipitation, solvent extraction and ion exchange processes, and summarized their advantages and disadvantages. The results showed that a single treatment technology was difficult to remove Tl to a trace level of "μg L^-1", which required combined multi-technology to enhance the removal efficiency. In addition, the potential emergency and feasible technologies for Tl removal were recommended. However, several fundamental issues, such as the comparative toxicity of Tl(I) and Tl(III), the confliction of hydrolysis constants, the interference of complexant ligands as well as the influence of redox potential, were still needed to be addressed, since they would profoundly affect the selection of adopted treatment methods and the behavior of Tl removal. Future research efforts concerning the improvement of existing Tl removal technologies should be devoted to (a) developing multi-functional chemicals and adsorbents, non-toxic extractants, easy-recovery ion exchange resin and high-efficient coupling technology for advanced treatment, (b) carrying out large-scale experiments and economic assessment for real wastewater, and (c) providing safe-disposal treatment for the exhausted adsorption materials or sludge.

An Ex-Situ Immobilization Experiment with Zn, Pb, and Cu in Dredged Marine Sediments from Bohai Bay, China

The remediation of dredged marine sediments contaminated by metals has drawn increasing attention globally. Immobilization was regarded as a promising method for reducing adverse impacts on marine ecosystems. In this study, kaolinite and limestone were used as amendments to immobilize Zn, Pb, and Cu in dredged marine sediments, which were collected from the coastal zone adjacent to Tianjin Port in Bohai Bay. The sequential extraction procedure was applied to identify the mobility of metals and, further, to evaluate the immobilization effect of the amendments. The physical–chemical properties of the sediments, such as the pH, electrical conductivity (EC), salinity, and total organic carbon (TOC), were also measured to better understand their influence on the three metals’ mobility. The results of the sequential extraction procedure indicated that the mobile fractions of the metals were converted into relatively stable fractions because of the two amendments. In addition, the EC, salinity, and TOC decreased moderately, while no obvious variations in the pH of the sediments were observed with the addition of kaolinite and limestone. It was confirmed that both kaolinite and limestone can effectively reduce the mobility and bioavailability of metals, particularly Zn, and limestone generally has a better immobilization effect, compared with kaolinite.

The effects of interaction between vermiculite and manganese dioxide on the environmental geochemical process of thallium

The interaction among various soil minerals can significantly impact on the environmental geochemical process of contaminants. Therefore, this study investigated the effects of interaction between vermiculite (VER) and manganese dioxide (MnO₂) on the migration and transformation of Tl(I). The VER exhibited typical layered structure and MnO₂ possessed a flower-like structure with serious reunion phenomenon, while the production of interaction between vermiculite and manganese dioxide, labeled VER-MnO₂, illustrated as fish scales evenly spread over a large sheet, suggesting that MnO₂ could triumphantly be anchored on the VER and the aggregation of MnO₂ was prevented. Compared with the pure MnO₂, VER acted as template substrate contributed the higher specific surface area (298.18 m²·g^-1) and the oxidation degree of Mn. VER-MnO₂ showed the highest fixation capacity (144.29 mg·g^-1) than other two materials in the order VER-MnO₂ > MnO₂ > VER, and there was no risk derived from Mn dissolution. The influence mechanism of VER-MnO₂ on Tl(I) migration and transformation lied in immobilization, ion exchange and oxidization. Fixed-bed column immobilization experiments showed that VER-MnO₂ could purify drinking water contaminated by Tl (20 μg·L^-1) and the effective breakthrough volumes were 900 bed volumes until reaching the maximum limits allowed in drinking water (0.1 μg·L^-1). VER-MnO₂ excellently catches Tl to prevent groundwater pollution. This study provides a theoretical guidance for environmental fate and restoration of soil heavy metal pollution.

Facile one-pot synthesis of thiol-functionalized mesoporous silica submicrospheres for Tl(I) adsorption: Isotherm, kinetic and thermodynamic studies

For the first time, thiol-modified mesoporous silica submicrospheres (TMS-SMSs) have been applied to remove extremely high toxic Tl(I) ions from aqueous solution by an adsorption approach. TMS-SMSs as a silica-based material is basically environmentally benign, with combined advantages of porosity and functionality. XRD measurement and TEM images clearly exhibited a parallel arrangement of mesopores in TMS-SMSs with a combination of both semi-long-range ordering and wormhole-like motif structures. The batch adsorption of Tl(I) onto TMS-SMSs showed a typical Langmuir adsorption isotherm (among various non-linear isotherm models) with the maximum adsorption capacity of 452.8 mgg^-1. TMS-SMSs show a fast adsorption rate, and pseudo-second-order kinetic model provides the best correlation between experimental data. The thermodynamic constants indicated that the adsorption of Tl(I) ions was an endothermic (ΔH° = 24.80 kJ  mol^-1), entropy driven (ΔS° = 0.161 kJ  mol^-1K^-1), and spontaneous process (ΔG° = 23.15-27.95 kJ mol^-1). This study provides an exciting opportunity to advance our knowledge of functionalized-mesoporous silica submicrospheres as a promising adsorbent for the removal of toxic Tl(I) ions from aqueous solution using adsorption approach.

Adsorption of thallium(I) on rutile nano-titanium dioxide and environmental implications

Rutile nano-titanium dioxide (RNTD) characterized by loose particles with diameter in 20–50 nm has a very large surface area for adsorption of Tl, a typical trace metal that has severe toxicity. The increasing application of RNTD and widespread discharge of Tl-bearing effluents from various industrial activities would increase the risk of their co-exposure in aquatic environments. The adsorption behavior of Tl(I) (a prevalent form of Tl in nature) on RNTD was studied as a function of solution pH, temperature, and ion strength. Adsorption isotherms, kinetics, and thermodynamics for Tl(I) were also investigated. The adsorption of Tl(I) on RNTD started at very low pH values and increased abruptly, then maintained at high level with increasing pH >9. Uptake of Tl(I) was very fast on RNTD in the first 15 min then slowed down. The adsorption of Tl(I) on RNTD was an exothermic process; and the adsorption isotherm of Tl(I) followed the Langmuir model, with the maximum adsorption amount of 51.2 mg/g at room temperature. The kinetics of Tl adsorption can be described by a pseudo-second-order equation. FT-IR spectroscopy revealed that -OH and -TiOO-H play an important role in the adsorption. All these results indicate that RNTD has a fast adsorption rate and excellent adsorption amount for Tl(I), which can thus alter the transport, bioavailability and fate of Tl(I) in aqueous environment.

Thallium pollution in China and removal technologies for waters: A review

Thallium (Tl) is a typical toxic metal, which poses a great threat to human health through drinking water and the food chain (biomagnification). China has rich Tl-bearing mineral resources, which have been extensively explored and utilized, leading to release of large amounts of Tl into the environment. However, research on Tl pollution and removal techniques is relatively limited, because Tl has not been listed within the scope of environmental monitoring in China for several decades. This paper reviewed Tl pollution in wastewater arising from various industries in China, as well as the latest available methods for treating Tl-containing industrial wastewater, in order to give an outlook on effective technologies for controlling Tl pollution. Conventional physical and chemical treatment technologies are efficient at removing trace amounts of Tl, but it proved to be difficult to achieve the stringent environmental standard (≤0.1-5 μg/L) cost-effectively. Adsorption by using newly developed nanomaterials, and metal oxide modified polymer materials and microbial fuel cells are highly promising and expected to become next-generation technologies for remediation of Tl pollution. With the potential for greater Tl contamination in the environment under accelerated growth of industrialization, researches based on lab-scale implementation of such promising treatment technologies should be further expanded to pilot and industrial scale, ensuring environmental protection and the safety of drinking water for sustainable development. Comprehensive insights into experiences of Tl pollution in China and in-depth perspectives on new frontier technologies of Tl removal from wastewaters will also benefit other nations/regions worldwide, which are susceptible to high exposure to Tl likewise.

Molecular design of macrocyclic compounds for complete removal of thallium(I) from wastewater

Design of new adsorbents for complete removal of thallium(I) from wastewater is of significant importance. Based on the theory of binding ability between crown ether and metal ion, a kind of Tl(I)-selected crown ether, thio-18-crown-6 ether, was designed. Subsequently, modeling calculations were performed to investigate the microscopic interaction between 18-crown-6 ether and its sulfur-substituted derivatives with Tl⁺. The results showed that thio-18-crown-6 ether generally showed higher affinity to Tl⁺ than 18-crown-6. The stabilities of these complexes ranked in an order of 5S-18C6 > 4S-18C6(II) > 2S-18C6(I) > 2S-18C6(II) > 6S-18C6 > 3S-18C6 > 18C6 > 1S-18C6. The binding energies of 5S-18C6 with free Zn²⁺, Pb²⁺, Cu²⁺, and Cd²⁺, which are usually impurity ions in thallium-containing wastewater, were more negative than with Tl⁺, indicating more affinity of 5S-18C6 toward these free two-valence ions. However, after the influence of solvent (water) was taken into account, 5S-18C6 showed fairly high selectivity to Tl(I) over Zn²⁺, Pb²⁺, Cu²⁺, and Cd²⁺. Therefore, 5S-18C6 should be a proper compound which has the promising potential to be adopted for the complete and selective removal of Tl(I) from wastewater. Further synthesis and adsorption experiments are needed to verify this prediction.