SnS2/SnO2 heterostructured nanosheet arrays grown on carbon cloth for efficient photocatalytic reduction of Cr(VI)

Controllable fabrication of SbxBi2-xS3 solid solution photocatalysts with superior elimination for Cr(VI)

The development of environmentally friendly and cost-effective photocatalysts is of vital significance for the effective removal of heavy metal contamination in water, but it is still a crucial challenge. Herein, the novel SbxBi2-xS3 solid solution photocatalysts with a certain amount of sulfur vacancy were prepared by adjusting the molar ratio of Sb to Bi through a simple hydrothermal strategy, and was applied to the effective photocatalytic reduction of hexavalent chromium (Cr(VI)). Sb1.75Bi0.25S3 with optimized ratio has superior reduction performance of Cr(VI), and the photocatalytic efficiency of Cr(VI) can achieve 91.9 % within 1 h of visible light illumination. The remarkable catalytic efficiency is due to the more applicable band structure of the solid solution photocatalyst, which is conducive for the photocatalytic reaction. Moreover, the substitution of Bi causes the crystal distortion of Sb2S3 and induce the generation of sulfur defects, which can effectively capture photoelectrons, accelerate the carriers separation, and improve the reduction performance. This study provides a hopeful photocatalyst for wastewater purification and promotes the exploration of solid solution photocatalyst in water environment remediation.

A novel insight into the microwave induced catalytic reduction mechanism in aqueous Cr(VI) removal over ZnFe2O4 catalyst

Aqueous Cr(VI) pollution is an emerging environmental issue. Herein, a sphere-like ZnFe₂O₄ catalyst with a size of ∼430 nm was prepared by a solvothermal method, by which the aqueous Cr(VI) in a 50 mL solution with concentration of 50 mg/L was completely removed after 10 min-microwave (MW) irradiation. "Surface temperature visualization" tests and COMSOL simulations showed that the surface temperature of the as-prepared ZnFe₂O₄ catalysts could be as high as > 1000 °C only after 300 s MW irradiation, and the work function calculations and scavenging experiments demonstrated that the excited electrons derived by the "hot spots" effect of the ZnFe₂O₄ catalysts reduced the Cr(VI) to Cr(III). Kinetic reaction process of the reduction of *Cr₂O₇^2- to *CrO₃H₃ over the ZnFe₂O₄ catalysts was clarified by using DFT calculation, and the results indicated that *Cr₂O₇^2- adsorbed on the Fe atoms was more easily to be reduced, and that Fe atoms played more significant roles than the Zn and O atoms in ZnFe₂O₄ catalysts. The present study not only proves that the MW induced ZnFe₂O₄ catalytic reduction was promising for ultrafast remediation of toxic Cr(VI), but also provides a new insight into the corresponding mechanism.

Synthesis and Applications of Dimensional SnS2 and SnS2/Carbon Nanomaterials

Dimensional nanomaterials can offer enhanced application properties benefiting from their sizes and morphological orientations. Tin disulfide (SnS₂) and carbon are typical sources of dimensional nanomaterials. SnS₂ is a semiconductor with visible light adsorption properties and has shown high energy density and long cycle life in energy storage processes. The integration of SnS₂ and carbon materials has shown enhanced visible light absorption and electron transmission efficiency. This helps to alleviate the volume expansion of SnS₂ which is a limitation during energy storage processes and provides a favorable bandgap in photocatalytic degradation. Several innovative approaches have been geared toward controlling the size, shape, and hybridization of SnS₂/Carbon composite nanostructures. However, dimensional nanomaterials of SnS₂ and SnS₂/Carbon have rarely been discussed. This review summarizes the synthesis methods of zero-, one-, two-, and three-dimensional SnS₂ and SnS₂/Carbon composite nanomaterials through wet and solid-state synthesis strategies. Moreover, the unique properties that promote their advances in photocatalysis and energy conversion and storage are discussed. Finally, some remarks and perspectives on the challenges and opportunities for exploring advanced SnS₂/Carbon nanomaterials are presented.

Anchoring ZnIn2S4 nanosheets on ZSM-5 for boosting photocatalytic Cr(vi) reduction

ZSM-5@ZnIn2S4 is constructed for highly efficient photocatalytic Cr(vi) reduction.

Preparation and application of BiOBr-Bi2S3 heterojunctions for efficient photocatalytic removal of Cr(VI)

Recently, the photocatalytic reduction of Cr(VI) has been extensively studied. Herein, we successfully prepared the BiOBr-Bi₂S₃ heterojunctions with high photocatalytic Cr(VI) reduction performance using an ion exchange method. The optimal BiOBr-Bi₂S₃ heterojunction (prepared with BiOBr, pH of 6.0, 2 mmol Na₂S₂O₃·5H₂O,) achieved 100% removal of Cr(VI) within 12 min. The performance of photo-reduced Cr(VI) was about 28.9 and 184.6 times higher than that of pure Bi₂S₃ and BiOBr, respectively. Besides, BiOBr-Bi₂S₃ heterojunctions had a good adsorption efficiency for Cr(III), suggesting that they could be applied as bifunctional photocatalyst. The formation process and photoelectric properties of the BiOBr-Bi₂S₃ heterojunctions were revealed by a series of characterizations. In conclusion, this work reported the synergistic effect of adsorption and photocatalysis of the BiOBr-Bi₂S₃ heterojunctions for Cr removal for the first time, suggesting that the BiOBr-Bi₂S₃ heterojunctions could act as a novel photocatalytic adsorbent to treat the Cr(VI)-containing wastewater.

Synthesis of hydroxide-enriched cerium-doped oxy-sulfide catalyst for visible light-assisted reduction of Cr(vi)

Semiconductor catalysts are significantly attractive materials for different cutting-edge applications, including the detoxification of toxic pollutants.

The enhanced photocatalytic performance of SnS2@MoS2 QDs with highly-efficient charge transfer and visible light utilization for selective reduction of mythlen-blue

Molybdenum disulfide (MoS₂) has recently been considered as an effective material for potential photocatalytic applications; however, its photocatalytic activity was limited due to the low density of active sites. In this work, MoS₂ Quantum dots (QDs) were synthesized via the ultrasonication technique to construct heterostructure with SnS₂ nanosheets (SnS₂@MoS₂ QDs) and the prepared materials were tested for photocatalytic applications for Methylene blue (MB). Pristine SnS₂ and SnS₂@MoS₂ QDs nanocomposite were analyzed by XRD, TEM, PL, and Uv-Vis. Both SnS₂ and SnS₂@MoS₂ QDs exhibited a single trigonal phase with the P-3m1 space group. The TEM analysis confirmed the coupling between the pristine SnS₂ and SnS₂@MoS₂ QDs. The results of photocatalytic activity toward MB indicated that SnS₂@MoS₂ QDs material exhibits much superior photocatalytic performance compared to pristine SnS₂. The excellent photodegradation performance of SnS₂@MoS₂ QDs is due in the main to the formation of heterojunction between SnS₂ and MoS₂ QDs with narrow bandgap formation, which results in a facile carriers transfer and thus high photocatalytic efficiency. A representative mechanism of the photodegradation for SnS₂@MoS₂ QDs photocatalyst was proposed. Such an ultrasonic technique is capable of producing small metallic particle size that can be used to construct new heterostructures for water remediation applications.

Photocatalytic decontamination of tetracycline and Cr(VI) by a novel α-FeOOH/FeS2 photocatalyst: One-pot hydrothermal synthesis and Z-scheme reaction mechanism insight

Tetracycline and Cr(VI) as non-biodegradable environmental contaminants have attracted increasing attention because of their chronic toxicity. In this regard, the environmentally friendly Z-scheme photocatalytic decontamination system has been widely used for contaminant treatment. Herein, a novel 3D Z-scheme α-FeOOH/FeS₂ composite photocatalyst was successfully synthesized for the first time via a simple one-pot hydrothermal method. X-ray diffraction (XRD) and Fourier-transform infrared (FT-IR) analyses and high-resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS) demonstrated that the O component of the heterogeneous nanostructures formed by the FeOFe linkages in α-FeOOH was replaced by S to generate FeSFe linkages in the resulting FeS₂. As expected, the novel 3D Z-scheme α-FeOOH/FeS₂ composites exhibited remarkable photocatalytic activity for Cr(VI) reduction and tetracycline degradation compared to pure α-FeOOH. Photoluminesence (PL) measurement and electrochemical impedance spectroscopy (EIS), as well as density functional theory (DFT) calculations, suggested that the enhanced photocatalytic activity of the Z-scheme α-FeOOH/FeS₂ composite can be attributed to the improved photo-absorption properties and the effective separation of photo-induced charge carriers caused by the Z-scheme system of the as-prepared 3D α-FeOOH/FeS₂ composites. Thus, this work may facilitate the effective design of α-FeOOH-based photocatalysts.

Recognition of M2 type tumor-associated macrophages with ultrasensitive and biocompatible photoelectrochemical cytosensor based on Ce doped SnO2/SnS2 nano heterostructure

Tumor-associated macrophages (TAMs) play central roles in the regulation of tumor growth. TAMs can be differentiated into M1 and M2 types, which are responsible for the inhibition and growth of tumor tissues, respectively. Recognition of M2-TAMs is significant for the diagnosis and therapy of cancer, which is however severely limited due to the deficiency of selective and sensitive photoelectrochemical sensors. In this work, using Ce doped SnO₂/SnS₂ nano heterostructure as the highly sensitive platform, a photoelectrochemical sensor enabling the recognition of M2-TAMs was fabricated for the first time. By the decoration of CD163 antibody on the platform, the ultrasensitive photoelectrochemical sensor can selectively detect the CD163 protein on the surface of M2-TAMs. To our best knowledge, this is the first demonstration for recognition of M2-TAMs using photoelectrochemical method. The fabricated cytosensor has ultra-sensitive photocurrent response, applicable biological compatibility, high selectivity and relatively wide linear sensing range (5 × 10¹ to 1 × 10⁵ cells/ml) with a low detection limit (50 cells/ml) for the detection of M2-TAMS. This kind of PEC cytosensor would provide a novel analysis and detection strategy for M2-TAMs.

Construction of Ag3PO4/SnO2 Heterojunction on Carbon Cloth with Enhanced Visible Light Photocatalytic Degradation

In this study, the Ag3PO4/SnO2 heterojunction on carbon cloth (Ag3PO4/SnO2/CC) was successfully fabricated via a facile two-step process. The results showed that the Ag3PO4/SnO2/CC heterojunction exhibited a remarkable photocatalytic performance for the degradation of Rhodamine B (RhB) and methylene blue (MB), under visible light irradiation. The calculated k values for the degradation of RhB and MB over Ag3PO4/SnO2/CC are 0.04716 min−1 and 0.04916 min−1, which are higher than those calculated for the reactions over Ag3PO4/SnO2, Ag3PO4/CC and SnO2/CC, respectively. The enhanced photocatalytic activity could mainly be attributed to the improved separation efficiency of photogenerated electron-hole pairs, after the formation of the Ag3PO4/SnO2/CC heterojunction. Moreover, carbon cloth with a large specific surface area and excellent conductivity was used as the substrate, which helped to increase the contact area of dye solution with photocatalysts and the rapid transfer of photogenerated electrons. Notably, when compared with the powder catalyst, the catalysts supported on carbon cloth are easier to quickly recycle from the pollutant solution, thereby reducing the probability of recontamination.

Hierarchical Co-doped SnS2@Ni(OH)2 double-shell crystalline structure on carbon cloth with gradient pore distribution for superior capacitance

Hierarchical Co-doped SnS₂@Ni(OH)₂ double-shell nanosheet arrays are coated on carbon cloth, the vertically aligned arrays with gradient pore distribution can facilitate the charge/ion transfer rate, thus improve the energy storage performance.

A photoelectrochemical immunosensor based on CdS/CdTe-cosensitized SnO2 as a platform for the ultrasensitive detection of amyloid β-protein

An ultrasensitive label-free photoelectrochemical immunosensor was developed to detect amyloid β-protein based on CdS/CdTe-cosensitized SnO₂ nanoflowers.

Novel method of square wave voltammetry for deposition of Bi2S3 thin film: Photocatalytic reduction of hexavalent Cr in single and binary mixtures

In this work a new method of square‒wave voltammetry was performed for electrodepositing of Bi₂S₃ film on the stainless steel mesh surface as low-cost and effective substrate in visible light harvesting. First, the obtained porous film was characterized by X‒ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), atomic force microscopy (AFM), and Raman analysis. In following, photocatalytic activity of film for reduction of hexavalent Cr was evaluated under sunlight irradiation. Results suggested that the presence of voids having several nanometers to 2 μm diameters on the film surface plays key role in photocatalytic processes. Indeed, surface voids as trapping cites and producing routs leads to multiple scattering of visible light. It can be noted that morphology of thin film, substrate structure, and diameters of voids are the main parameters to achieving the high reduction efficiency. Cr(VI) was completely reduced within 100  min under sunlight irradiation. Photoreduction mechanistic studies induced by Bi₂S₃ film suggested that active oxygen species such as HOO^• and O₂ have significant role in photocatalytic reaction. Finally, the evaluation of simultaneous photocatalytic process of binary mixture (Cr(VI) and Rhodamin B) was shown synergistic improvement of Cr(VI) and Rhodamin B degradation due to rapid surface reactions.

Remarkable Improvement in Photocatalytic Performance for Tannery Wastewater Processing via SnS2 Modified with N-Doped Carbon Quantum Dots: Synthesis, Characterization, and 4-Nitrophenol-Aided Cr(VI) Photoreduction

Photocatalytic pathways are proved crucial for the sustainable production of chemicals and fuels required for a pollution-free planet. Electron-hole recombination is a critical problem that has, so far, limited the efficiency of the most promising photocatalytic materials. Here, the efficacy of the 0D N doped carbon quantum dots (N-CQDs) is demonstrated in accelerating the charge separation and transfer and thereby boosting the activity of a narrow-bandgap SnS₂ photocatalytic system. N-CQDs are in situ loaded onto SnS₂ nanosheets in forming N-CQDs/SnS₂ composite via an electrostatic interaction under hydrothermal conditions. Cr(VI) photoreduction rate of N-CQDs/SnS₂ is highly enhanced by engineering the loading contents of N-CQDs, in which the optimal N-CQDs/SnS₂ with 40 mol% N-CQDs exhibits a remarkable Cr(VI) photoreduction rate of 0.148 min^-1 , about 5-time and 148-time higher than that of SnS₂ and N-CQDs, respectively. Examining the photoexcited charges via zeta potential, X-ray photoelectron spectroscopy (XPS), surface photovoltage, and electrochemical impedance spectra indicate that the improved Cr(VI) photodegradation rate is linked to the strong electrostatic attraction between N-CQDs and SnS₂ nanosheets in composite, which favors efficient carrier utilization. To further boost the carrier utilization, 4-nitrophenol is introduced in this photocatalytic system and the efficiency of Cr(VI) photoreduction is further promoted.

Stable Copper Tin Sulfide Nanoflower Modified Carbon Quantum Dots for Improved Supercapacitors

Copper tin sulfides (CTSs) have widely been investigated as electrode materials for supercapacitors owing to their high theoretical pseudocapacitances. However, the poor intrinsic conductivity and volume change during redox reactions hindered their electrochemical performances and broad applications. In this study, carbon quantum dots (CQDs) were employed to modify CTSs. The structures and morphologies of obtained materials were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD revealed CTSs were composed of Cu2SnS3 and Cu4SnS4, and TEM suggested the decoration of CQDs on the surface of CTSs. With the decoration of CQDs, CTSs@CQDs showed a remarkable specific capacitance of 856 F·g−1 at 2 mV·s−1 and a high rate capability of 474 F·g−1 at 50 mV·s−1, which were superior to those of CTSs (851 F·g−1 at 2 mV·s−1 and 192 F·g−1 at 50 mV·s−1, respectively). This was mainly ascribed to incorporation of carbon quantum dots, which improved the electrical conductivity and alleviated volume change of CTSs during charge/discharge processes.

Synthesis of oxy-sulfide based nanocomposite catalyst for visible light-driven reduction of Cr(VI)

The oxy-sulfide based V₂O₅@(In,Ga)₂(O,S)₃ nanocomposite catalyst, at different weight percentages of V₂O₅, was successfully synthesized via a simplistic procedural route for the detoxification of hazardous Cr(VI). The two pure catalysts were intimately allied and used for visible light-driven reduction of hazardous Cr(VI). The nanocomposite catalysts were characterized to observe the effects of V₂O₅ on crystal phase, morphology, light absorption, catalytic activity, and electrical properties. Compared to all, 40% V₂O₅ loaded nanocomposite catalyst, designated as VOS-2, exhibited the best-reducing capability. It completely reduced toxic Cr(VI) at 2 min under visible light illumination. From the kinetics, it was found that the rate constant of the nanocomposite catalyst was improved by a factor of 3.6 compared to the host nanoflower catalyst. The plausible mechanism of charge transfer process across the interfacial region indicates the diminished recombination probability of photogenerated charge carriers. Therefore, the nanocomposite catalyst is promising for enhanced reduction of Cr(VI) in the Cr-based industrial activities, which is significantly relevant for environmental remediation.

Facile preparation of Ti3+ self-doped TiO2 nanoparticles and their dramatic visible photocatalytic activity for the fast treatment of highly concentrated Cr(vi) effluent

An efficient visible photocatalyst which is suitable for the rapid removal of highly concentrated Cr(vi) for environmental therapy.

Enhanced visible light absorption performance of SnS2 and SnSe2 via surface charge transfer doping

The layered two-dimensional (2D) SnS₂ and SnSe₂ have received intensive attention due to their sizable band gaps and potential properties. However, it has been shown that the visible light absorption of SnS₂ and SnSe₂ are restricted as photocatalysts and light-harvesting material absorbers for water splitting and high-performance optoelectronic devices. Herein, to enhance the visible light absorption performance of SnS₂ and SnSe₂, we performed a systematic investigation on tuning the electronic and optical properties of monolayers SnS₂ and SnSe₂ via surface charge transfer doping (SCTD) with the adsorption of molybdenum trioxide (MoO₃) and potassium (K) as surface dopants based on density functional theory. Our calculations reveal that MoO₃ molecules and K atoms can draw/donate electrons from/to SnS₂ and SnSe₂ as acceptors and donors, respectively. The adsorption of MoO₃ molecules introduces a new flat impurity state in the gap of the monolayers SnS₂/SnSe₂, and the Fermi level moves correspondingly to the top of valence band, resulting in a p-type doping of the monolayer SnS₂/SnSe₂. With the adsorption of K atoms, the electrons can transfer from K atoms to the monolayer of SnS₂ and SnSe₂, making K an effective electron-donating dopant. Meanwhile, the bandgaps of monolayers SnS₂ and SnSe₂ decrease after the MoO₃ and K doping, which leads to the appearance of appreciable new absorption peaks at around ∼650/480 and ∼600/680 nm, respectively, and yielding an enhanced visible light absorption of SnS₂ and SnSe₂. Our results unveil that SCTD is an effective way to improve the photocatalytic and light-harvesting performance of SnS₂ and SnSe₂, broadening their applications in splitting water and degrading environmental pollutants under sunlight irradiation.