Ultrahigh-surface-area activated carbon aerogels derived from glucose for high-performance organic pollutants adsorption

Enhanced adsorption of phenolic compounds using biomass-derived high surface area activated carbon: Isotherms, kinetics and thermodynamics

The progress of industrial and agricultural pursuits, along with the release of inadequately treated effluents especially phenolic pollutant, has amplified the pollution load on environment. These organic compounds pose considerable challenges in both drinking water and wastewater systems, given their toxicity, demanding high oxygen and limited biodegradability. Thus, developing an eco-friendly, low-cost and highly efficient adsorbent to treat the organic pollutants has become an important task. The present investigation highlights development of a novel adsorbent (CFPAC) by activation of Cassia fistula pod shell for the purpose of removing phenol and 2,4-dichlorophnenol (2,4-DCP). The significant operational factors (dosage, pH, concentration, temperature, speed) were also investigated. The factors such as pH = 2 and T = 20°C were found to be significant at 1.6 g/L and 0.6 g/L dosage for phenol and 2,4-DCP respectively. Batch experiments were further conducted to study isotherms, kinetic and thermodynamics studies for the removal of phenol and 2,4-DCP. The activated carbon was characterised as mesoporous (specific surface area 1146 m2/g, pore volume = 0.8628 cc/g), amorphous and pHPZC = 6.4. At optimum conditions, the maximum sorption capacity for phenol and 2,4-DCP were 183.79 mg/g and 374.4 mg/g respectively. The adsorption isotherm was better conformed to Redlich Peterson isotherm (phenol) and Langmuir isotherm (2,4-DCP). The kinetic study obeyed pseudo-second-order type behaviour for both the pollutants with R2 > 0.999. The thermodynamic studies and the value of isosteric heat of adsorption for both the pollutants suggested that the adsorption reaction was dominated by physical adsorption (ΔHx < 80 kJ/mol). Further, the whole process was feasible, exothermic and spontaneous in nature. The overall studies suggested that the activated carbon synthesised from Cassia fistula pods can be a promising adsorbent for phenolic compounds.

Facile engineering of mesoporous silica for the effective removal of anionic dyes from wastewater: Insights from DFT and experimental studies

The discharge of dye effluents from the textile industries has become a major environmental issue due to its potential to impart serious harm to human health and aquatic life. Mesoporous silica due to its high chemical stability, large surface area, tunable morphologies, large pore volume and pore size and cost-effectiveness is commonly used to remove such dyes before recycling of the wastewater for agricultural, domestic, and industrial applications. However, the low colloidal stability, the fast aggregation of the silica particles and the slow etching of the silica surface often results in the fast deactivation of the adsorbents and limits their long-term applications. In this study, we report the functionalization of mesoporous silica (SBA-15) with ZnO nanoparticles for the effective removal of anionic dyes. The Zn-silica exhibited highly positive surface with a dipole moment of 172 Debye and high charge transfer efficacy with an energy bandgap (ΔE) of 3.35 eV as revealed by quantum chemical DFT simulations. It achieved excellent removal of Alizarin red dye reaching a removal efficiency of 99.99 % and an adsorption capacity of 50 mg/g. In the presence of heavy metal ions commonly present in wastewater (Cd2+, Co2+, Zn2+, Ni2+, Cu2+ and Hg2+), the Zn-silica maintain excellent stability, high selectivity, and reusability within 5 cycles without a significant decline in efficiency. This study thus presents an effective way of wastewater purification on cost-effective adsorbents for meeting the water scarcity demands.

Waste newspaper driven activated carbon to remove polycyclic aromatic hydrocarbon from wastewater

In this study, a carbon-based adsorbent was developed from waste newspaper through pyrolysis at 800 °C to evaluate the removal efficiency of polycyclic aromatic hydrocarbons (Benzo[ghi]perylene (BghiP) and Indeno [1,2,3-cd] pyrene (IP)) from wastewater. The surface area of the developed adsorbent was estimated at 509.247m²g^-1 which allowed the adsorption of the PAHs from wastewater. The maximum adsorption capacity was estimated at 138.436 μg g^-1 and 228.705 μg g^-1 for BghiP and IP, respectively and the highest removal efficiency was observed at pH 2. Around 91% removal efficiency was observed at pH 7 for both pollutants. Experimental adsorption data were fit for pseudo-second-order kinetics and Langmuir isotherm models, which demonstrate electrostatic interaction, monolayered deposition, hydrogen bonding, and π-π interaction between adsorbate and adsorbent which play a significant role in adsorption. The regeneration study described that the developed adsorbent could be able to intake 52.75% BghiP and 48.073% IP until the 8th and 6th cycles, respectively. The removal efficiency of the adsorbent in the real sample was also evaluated. This study will provide a method to convert waste material into adsorbent and will remove PAHs from wastewater as a function of pollutant mitigation and waste management.

g-C3N4/polyvinyl alcohol-sodium alginate aerogel for removal of typical heterocyclic drugs from water

Heterocyclic drugs (HCDs) detected at high frequencies in wastewater have raised great concerns and their advanced removal has been the hotspot for safe water reuse in recent years. Two-dimensional graphitic carbon nitride (g-C₃N₄) and its photocatalytic systems are increasingly emerging, however, there are inevitable drawbacks of stacking and difficulty in recycling, resulting in decreased pollutant removal and limited application. Herein, for the first time, this paper reported a three-dimensional g-C₃N₄/polyvinyl alcohol-sodium alginate aerogel (g-C₃N₄/PVA-SA aerogel) photocatalyst synthesized by ultrasonic exfoliation and in-situ polymerization for typical HCDs (sulfadiazine (SDZ), sulfamethoxazole (SMX), and carbamazepine (CBZ)) removal in water. The reduced stacking of g-C₃N₄ dispersed in PVA-SA aerogel was achieved as revealed by scanning electron microscopy (SEM) and X-ray diffractometer (XRD) analysis, and g-C₃N₄/PVA-SA aerogel was observed to possess encouraging degradation efficiencies and rates for SDZ (100%, 0.0249 min^-1), SMX (100%, 0.1762 min^-1) and CBZ (69.8%, 0.0056 min^-1), which were improved by 50%-60% and 133%-216% compared to those of g-C₃N₄, respectively. Meanwhile, environmental impact factors such as pH and coexisting ions had less impact on the degradation of SDZ and SMX by g-C₃N₄/PVA-SA aerogel. The novel aerogel also had a good recyclability, with less than 5% reduction in degradation efficiency after five cycles observed. The photodegradation of SDZ, SMX and CBZ was confirmed to be driven by ⋅O₂^- and h⁺ through scavenger-quenching experiments. The new low carbon and recyclable g-C₃N₄/PVA-SA aerogel reported in this study indicated a good potential for efficient removal of HCDs from water, which provides an alternative strategy for advanced purification and safe reuse of wastewater.

Biopolymeric Fibrous Aerogels: The Sustainable Alternative for Water Remediation

The increment in water pollution due to the massive development in the industrial sector is a worldwide concern due to its impact on the environment and human health. Therefore, the development of new and sustainable alternatives for water remediation is needed. In this context, aerogels present high porosity, low density, and a remarkable adsorption capacity, making them candidates for remediation applications demonstrating high efficiency in removing pollutants from the air, soil, and water. Specifically, polymer-based aerogels could be modified in their high surface area to integrate functional groups, decrease their hydrophilicity, or increase their lipophilicity, among other variations, expanding and enhancing their efficiency as adsorbents for the removal of various pollutants in water. The aerogels based on natural polymers such as cellulose, chitosan, or alginate processed by different techniques presented high adsorption capacities, efficacy in oil/water separation and dye removal, and excellent recyclability after several cycles. Although there are different reviews based on aerogels, this work gives an overview of just the natural biopolymers employed to elaborate aerogels as an eco-friendly and renewable alternative. In addition, here we show the synthesis methods and applications in water cleaning from pollutants such as dyes, oil, and pharmaceuticals, providing novel information for the future development of biopolymeric-based aerogel.

Biomass Nanoarchitectonics for Supercapacitor Applications

Nanoarchitectonics integrates nanotechnology with numerous scientific disciplines to create innovative and novel functional materials from nano-units (atoms, molecules, and nanomaterials). The objective of nanoarchitectonics concept is to develop functional materials and systems with rationally architected functional units. This paper explores the progress and potential of this field using biomass nanoarchitectonics for supercapacitor applications as examples of energetic materials and devices. Strategic design of nanoporous carbons that exhibit ultra-high surface area and hierarchically pore architectures comprising micro- and mesopore structure and controlled pore size distributions are of great significance in energy-related applications, including in high-performance supercapacitors, lithium-ion batteries, and fuel cells. Agricultural wastes or natural biomass are lignocellulosic materials and are excellent carbon sources for the preparation of hierarchically porous carbons with an ultra-high surface area that are attractive materials in high-performance supercapacitor applications due to high electrical and ion conduction, extreme porosity, and exceptional chemical and thermal stability. In this review, we will focus on the latest advancements in the fabrication of hierarchical porous carbon materials from different biomass by chemical activation method. Particularly, the importance of biomass-derived ultra-high surface area porous carbons, hierarchical architectures with interconnected pores in high-energy storage, and high-performance supercapacitors applications will be discussed. Finally, the current challenges and outlook for the further improvement of carbon materials derived from biomass or agricultural wastes in the advancements of supercapacitor devices will be discussed.

Waste-Tire-Derived Activated Carbon as Efficient Adsorbent of P-Nitrophenol from Wastewater

In this work, a two-stage activation method was used to prepare adsorbents from scrap tire rubber. Firstly, KOH was mixed with rubber using different impregnation ratios (1–2) for primary activation; a second activation was performed after pyrolysis at 650°C and 750°C; and finally, the samples were acid-washed using HNO3. The prepared materials were characterized by elemental analysis, nitrogen adsorption isotherms, SEM, FTIR, and XPS. The adsorption capacity and mechanism of these materials on p-nitrophenol in wastewater were also investigated. It was found that after two-stage activation, the specific surface area of the materials can be effectively increased, and the surface of the materials can be enriched with oxygen-containing functional groups. The maximum adsorption capacity of PNP could reach 143.9 mg g−1, which is slightly higher than the literature data under the same conditions. The adsorption process is in the form of chemisorption and is dominated by hydrogen bonding and π-πEDA formation, but the adsorption tends to be monolayer, and the adsorption behavior can be described by a proposed secondary model. In addition, the adsorbent has a stronger adsorption capacity under acidic conditions.

A series of novel carbohydrate-based carbon adsorbents were synthesized by self-propagating combustion for tetracycline removal

Herein, a series of novel adsorbents derived from glucose, maltose, and starch zinc oxide (ZnO) loaded carbohydrate-based carbon materials (Zn-Cs) were synthesized by a fast and efficient self-propagating combustion synthesis method (SCS). The experimental results show that Zn-Cs exhibits excellent adsorption performance (>375 mg/g) to tetracycline, and the pseudo-second-order model and Freundlich model can better describe the adsorption data. The adsorption capacities of Zn-Cs were over 300 mg/g throughout the wide pH range (6-9), while various coexisting ions in the concentration range of 0-10 mg/L and the presence of humic acid had nearly no impact on the adsorption of tetracycline. Moreover, the adsorption experiment of simulated hospital wastewater shows that the adsorption capacity of Zn-Cs for tetracycline exceeds 185 mg/g. The adsorption mechanism of tetracycline are H-bond, complexation, and conjugation effect. This work provides an efficient, excellent versatility and time-saving strategy for preparing high-performance carbohydrate-based carbon materials for adsorbents.

Facile preparation and highly efficient sorption of magnetic composite graphene oxide/Fe3O4/GC for uranium removal

In this work, we reported for the first time a novel magnetic composite graphene oxide/Fe3O4/glucose-COOH (GO/Fe3O4/GC) that was facilely prepared from glucose through the hydrothermal carbonization and further combination with graphene oxide (GO). The chemical and structural properties of the samples were investigated. By the batch uranium adsorption experiments, the magnetic composite GO/Fe3O4/GC exhibits an excellent adsorption performance and fast solid-liquid separation for uranium from aqueous solution. GO/Fe3O4/GC (the maximum adsorption capacity (Qm) was 390.70 mg g-1) exhibited excellent adsorption capacity and higher removal rate (> 99%) for U(VI) than those of glucose-COOH (GC) and magnetic GC (MGC). The effect of the coexisting ions, such as Na+, K+, Mg2+, Ca2+, and Al3+, on the U(VI) removal efficiency of GO/Fe3O4/GC was examined. The equilibrium sorption and sorption rate for the as-prepared adsorbents well fit the Langmuir model and pseudo second-order kinetic model, respectively. The thermodynamic parameters (ΔH0 = 11.57 kJ mol-1 and ΔG0 < 0) for GO/Fe3O4/GC indicate that the sorption process of U(VI) was exothermic and spontaneous. Thus, this research provides a facile strategy for the preparation of the magnetic composite with low cost, high efficiency and fast separation for the U(VI) removal from aqueous solution.

Hierarchical nano-porous biochar prepared by a MgO template method for high performance of PNP adsorption

Hierarchical nano-porous biochar (HNBC) derived from Enteromorpha prolifera (EP) was prepared using a facile MgO templated strategy, which exhibits a remarkable adsorption performance for p-nitrophenol (PNP).

Use of NH4Cl for activation of carbon xerogel to prepare a novel efficacious adsorbent for benzene removal from contaminated air streams in a fixed-bed column

BACKGROUND

Ammonium chloride as an explosive salt has proved to be a prominent activation agent for adsorbents and increase the specific surface area and volume of cavities. In this work, the ability of this substance was scrutinized for activation of carbon aerogel to prepare an efficient adsorbent for benzene removal from air streams.

METHODS

A carbon xerogel was fabricated from Novallac polymer and activated by ammonium chloride.The changes in structure and morphology were considered via Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), Barrett-Joyner-Halenda (BJH), and energy dispersive X-ray (EDX) analyses. Also, comprehensive studies were conducted to vouchsafe the properties of the new adsorbent for benzene removal, using a fixed-bed column mode.

RESULTS

The results showed both the successful synthesis and the suitability of the activation process. ACX possessed a higher specific surface area (1008 g/m³), compared to the parent carbon xerogel (CX; 543.7 g/m³) and organic xerogel (OX; 47 g/m³), as well as a higher adsorption capacity.

CONCLUSION

NH₄CL is a very beneficial for modifying the structure and morphology of carbon aerogel, and the dynamic behavior of the column with respect inlet benzene concentration can be explained by Yan-Nelson model.

Directionally-Grown Carboxymethyl Cellulose/Reduced Graphene Oxide Aerogel with Excellent Structure Stability and Adsorption Capacity

A novel three-dimensional carboxymethyl cellulose (CMC)/reduced graphene oxide (rGO) composite aerogel crosslinked by poly (methyl vinyl ether-co-maleic acid)/poly (ethylene glycol) system via a directional freezing technique exhibits high structure stability while simultaneously maintaining its excellent adsorption capacity to remove organic dyes from liquid. A series of crosslinked aerogels with different amounts of GO were investigated for their adsorption capacity of methylene blue (MB), which were found to be superb adsorbents, and the maximum adsorption capacity reached 520.67 mg/g with the incorporation of rGO. The adsorption kinetics and isotherm studies revealed that the adsorption process followed the pseudo-second-order model and the Langmuir adsorption model, and the adsorption was a spontaneous process. Furthermore, the crosslinked aerogel can be easily recycled after washing with dilute HCl solution, which could retain over 97% of the adsorption capacity after recycling five times. These excellent properties endow the crosslinked CMC/rGO aerogel’s potential in wastewater treatment and environment protection.

Immobilization of β-CD on a Hyper-Crosslinked Polymer for the Enhanced Removal of Amines from Aqueous Solutions

In this paper, we adopted a simple and efficient strategy to prepare a β-cyclodextrin (β-CD)-modified hyper-crosslinked polymer (CDM-HCP). The structures and physicochemical properties of the as-synthesized polymer were also evaluated. It was applied to the removal of anilines from aqueous solutions. The introduction of β-CD into the hyper-crosslinked polymer significantly enhanced adsorption properties for the removal of various amines. The adsorption kinetics agreed with the pseudo-second-order mode very well. The adsorption isotherm data of p-methylaniline (p-MA) and p-aminobenzoic acid (p-ABC) were in agreement with the Langmuir isotherm, whereas aniline and p-chloroaniline (p-CA) were fitted best with the Freundlich model. The maximum adsorption capacities (q_max) determined by adsorption isotherms were 148.97 mg/g for aniline, 198.45 mg/g for p-MA, 293.71 mg/g for p-CA, and 622.91 mg/g for p-ABC, respectively. It had higher adsorption capacities than those of some commercial polymeric resins, such as XAD-4, PA66, and AB-8. The interaction mechanism was investigated by FTIR, XPS, and the ONIOM2 method. A CDM-HCP can be regenerated efficiently and used repeatedly, indicating its potential technological applications in removing organic pollutants from actual industrial effluents.

Ultrahigh adsorbability towards different antibiotic residues on fore-modified self-functionalized biochar: Competitive adsorption and mechanism studies

An ultrasonic-assistant fore-modified method was designed to develop the self-functionalized biochar (SFB) with enhanced adsorbability. Characterized by different morphologies, SFB was presenting particular groups of carbon micro-spheres. Possessing ultrahigh surface area of 2368 m²/g, SFB exhibited excellent adsorption capacity (up to 497 mg/g) towards traditional antibiotic. Besides, more functional groups, which played important roles on the solid-liquid interface interaction, posed on the surface of SFB. The removal efficiency of levofloxacin was up to 99.93 % in the competitive system. Adsorption mechanism was analyzed based on the results of FTIR, kinetics, isotherms and competitive adsorption experiments. The chemisorption affinity on the solid-liquid interface was strong enough, which was proved by isotherms, thermodynamics and K_d analyses. Meanwhile, SFB has presented a good resistance against humid acid interference in aqueous environment. Thus, the ultrasonic-assistant fore-modified method was potential in dramatically improving the feature of biochars. SFB presented excellent adsorbability to antibiotics and exhibits extraordinary potential in wastewater treatment.

Corncob-derived activated carbon for roxarsone removal from aqueous solution: isotherms, kinetics, and mechanism

In this study, the adsorption of roxarsone (ROX) onto corncob-derived activated carbon (AC) was optimized using response surface methodology (RSM). Following this, the AC was comprehensively characterized by FT-IR, SEM, and EDS analysis. The results showed that the highest ROX adsorption efficiency of 304.34 mg/g was obtained at the contact time of 262 min, initial pH of 2.5, adsorbent dosage of 0.4 g/L, and initial concentration of 240 mg/L. Besides, it was found that the adsorption equilibrium data was fitted well to the Langmuir and Sips isotherm models. The thermodynamic parameters (e.g., ΔG, ΔH, and ΔS) revealed the spontaneous and exothermic nature of ROX adsorption. As indicated by pseudo second-order kinetics model, the adsorption of ROX onto AC could be achieved through the hydrogen bond, π-π adsorbate-adsorbent interaction, and electrostatic interaction between AC surface functional group and molecular species variations of ROX at different pH values. Overall, it can be concluded that corncob-derived AC is an alternative option for removing ROX from aqueous solution.

Competitive adsorption of tylosin, sulfamethoxazole and Cu(II) on nano-hydroxyapatitemodified biochar in water

Antibiotics and heavy metals are frequently detected simultaneously in water environment. In this study, the competitive adsorption behavior of tylosin (TYL) and sulfamethoxazole (SMX) on nano-hydroxyapatite modified biochar (nHAP@biochar) in accordance with Cu(II) in single, binary and ternary systems was investigated. The specific surface area of nHAP@biochar was 566.056 m²/g. The adsorption of TYL on nHAP@biochar reduced by 13.36%-41.04% or 9.92%-38.69% with Cu(II) and SMX in the solution, respectively. The suppression of SMX was stronger than Cu(II) on the adsorption of TYL when the SMX or Cu(II) was constant. The adsorption of SMX increased by 2.01-3.56 times in the present of Cu(II), while suppressed by TYL up to 42.30%. Due to the bridging of TYL or SMX between the nHAP@biochar and Cu(II) and destroying of bound water surrounded, the adsorption of Cu(II) increased to a greater extent. Electrostatic interaction and H-bond were the two main interactions between TYL, SMX and Cu(II) and nHAP@biochar. π-π interactions was also interaction between the SMX and nHAP@biochar.

Ultra-high adsorption of tetracycline antibiotics on garlic skin-derived porous biomass carbon with high surface area

A porous carbon material with ultra-high specific surface area was prepared from waste garlic skin, and exhibited excellent adsorption properties to TCs in a water environment.

High-efficiency adsorption and regeneration of methylene blue and aniline onto activated carbon from waste edible fungus residue and its possible mechanism

Edible fungus residue as an efficient and low-cost precursor was used to produce Edible Fungus residue Activated Carbon (EFAC) using the zinc chloride activation method at a 1 : 2 impregnation ratio and 600 °C activation for 3 hours. The activation process does not need gases like nitrogen and is suitable for mass production. Fungal biodegradation facilitates efficient chemical activation, which might have generated abundant pores on the activated carbon sample. Using BET, X-ray diffraction (XRD), scanning electron microscopy (SEM), and FTIR characterization, reveals that EFAC exhibits a large specific surface area (1070 m² g⁻¹), and large pore volume (0.68 cm³ g⁻¹), with its surface displaying a honeycomb-like structure. The EFAC adsorbs methylene blue (MB) and aniline in water, with maximum adsorptions of 662.25 and 27.10 mg g⁻¹, respectively. Various adsorption conditions, such as the EFAC dosage, pH, contact time and initial concentration were investigated. The adsorption is characterized by the pseudo-second-order kinetic and Langmuir isotherm models, with thermodynamics studies indicating that the adsorption is endothermic and spontaneous. Furthermore, the EFAC exhibited good regeneration performance by a 90% ethanol solution. The EFAC is a low-cost and environmentally friendly adsorbent for removing organic contaminants in wastewater.

Edible fungus residue as an efficient and low-cost precursor was used to produce Edible Fungus residue Activated Carbon (EFAC) using the zinc chloride activation method at a 1 : 2 impregnation ratio and 600 °C activation for 3 hours.