Encapsulation and sedimentation of nanomaterials through complex coacervation

Interaction of chitosan with nanoplastic in water: The effect of environmental conditions, particle properties, and potential for in situ remediation

Micro- and nanoplastic (MNP) pollution in aquatic ecosystems requires investigation on its source, transport, and extent to assess and mitigate its risks. Chitosan is a potential biomolecule for water treatment, but its interaction with MNP is undefined. In this work, chitosan-nanoplastic interaction was explored in the laboratory under environmentally relevant conditions using polystyrene (PS) nanoplastic (NP) as model particle to identify conditions at which PS-chitosan interaction resulted in aggregation. Aggregation limits NP transport and allows separation of NP for targeted remediation. The effect of environmental conditions (pH, salinity, dissolved organic matter (DOM) content), chitosan particle size and NP surface modification on chitosan-NP interaction was studied at various chitosan doses. PS aggregated at chitosan doses as low as 0.2 % w/w, while higher doses of chitosan resulted in re-stabilization of NP in solution, restoring the particle size to its initial value. Increasing pH, DOM, or carboxyl modification of the NP surface also improved NP stability in solution. Increased salinity of the solution caused aggregation of unmodified PS independent of chitosan, but carboxyl-modified PS remained stable and aggregated at the same chitosan doses across all salinity levels. Chitosan with low molecular weight promoted PS aggregation at lower doses. Notably, zeta potential (ZP) alone did not indicate chitosan-induced PS aggregation, which occurred independently of changes in ZP. DLVO calculations based on ZP, however, still indicated attractive interaction due to charge differences, albeit with less contrast at high pH, salinity, and DOM content. Additional insights gained in the work recommend caution when using spectrophotometric methods to assess NP removal. Overall, this study demonstrates that chitosan impacts NP transport and holds potential for water remediation of NP.

Bovine Serum Albumin Nanoparticles Enhanced the Intranasal Bioavailability of Silybin in Rats

Silybin (SLB), an important flavonoid from silymarin, displays significant hepatoprotective, anticancer, antioxidant, and neuroprotective effects. However, its therapeutic efficacy is limited by its low solubility and bioavailability. To address these challenges, we engineered bovine serum albumin (BSA) nanoparticles (NP) loaded with SLB (BSA-NP/SLB) using the coacervation method. BSA-SLB NP exhibited a spherical shape, a mean size of 197 nm, a polydispersity index of 0.275, a zeta potential of -34 mV, and an entrapment efficiency of 67%. X-ray diffraction analysis indicated amorphization of SLB upon encapsulation. Formulation stability was upheld over 180 days. In vitro release assays demonstrated controlled diffusion-erosion release, with approximately 40% SLB released within 0.5 h and 100% over 12 h. Intranasal administration of BSA-NP/SLB in rats improved SLB bioavailability by fourfold compared to free SLB. These findings highlight the promising potential of intranasally administered BSA-NP/SLB as an alternative approach to enhance SLB bioavailability, paving the way for innovative therapeutic applications.

Protein-like particles through nanoprecipitation of mixtures of polymers of opposite charge

HYPOTHESIS

Polymer nanoparticles (NPs) have a very high potential for applications notably in the biomedical field. However, synthetic polymer NPs cannot yet concurrence the functionalities of proteins, their natural counterparts, notably in terms of size, control over internal structure and interactions with biological environments. We hypothesize that kinetic trapping of polymers bearing oppositely charged groups in NPs could bring a new level of control and allow mimicking the surfaces of proteins.

EXPERIMENTS

Here, the assembly of mixed-charge polymer NPs through nanoprecipitation of mixtures of oppositely charged polymers is studied. Two series of copolymers made of ethyl methacrylate and 1 to 25 mol% of either methacrylic acid or a trimethylammonium bearing methacrylate are synthesized. These carboxylic acid or trimethylammonium bearing polymers are then mixed in different ratios and nanoprecipitated. The influence of the charge fraction, mixing ratio of the polymers, and precipitation conditions on NP size and surface charge is studied.

FINDINGS

Using this approach, NPs of less than 25 nm with tunable surface charge from +40 mV to -40 mV are assembled. The resulting NPs are sensitive to pH and certain NP formulations have an isoelectric point allowing repeated charge reversal. Encapsulation of fluorescent dyes yields very bright fluorescent NPs, whose interactions with cells are studied through fluorescence microscopy. The obtained results show the potential of nanoprecipitation of oppositely charged polymers for the design of NPs with precisely tuned surface properties.

Sunscreen Enhancement of Octyl Methoxycinnamate Microcapsules by Using Two Biopolymers as Wall Materials

Octyl methoxycinnamate (OMC) is widely used as a chemical sunscreen in sunscreen cosmetics. However, its direct contact with the skin would bring certain risks, such as skin photosensitive reaction. How to improve the effect of skin photodamage protection has become a current research hotspot. Encapsulating ultraviolet (UV) filters into microcapsules is an interesting method to increase the photostability of filters. In this study, sodium caseinate (SC) and arabic gum (GA) are chosen as wall materials to prepare synergistic sunscreen microcapsules by complex coacervation technology. A series of experiments are conducted to investigate the effects of pH, wall material concentration, and wall/core ratio on the formation of OMC microcapsules. The morphology, composition, and stability of OMC microcapsules are characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The OMC microcapsule is uniform in size distribution, smooth in surface morphology, and has good thermal stability. The results show that the ultraviolet absorption of the OMC microcapsules is better than that of the uncoated OMC for the ultraviolet-B (280–320 nm). Moreover, the OMC microcapsule released 40% in 12 h, while OMC released 65%, but the sun protection factor (SPF) of the OMC microcapsule sunscreen is 18.75% higher than that of OMC. This phenomenon may be attributed to the hydrophobic interaction between SC and OMC and the electrostatic interaction between SC and GA.