Fabrication of zirconium-based metal-organic frameworks@tungsten trioxide (UiO-66-NH2@WO3) heterostructure on carbon cloth for efficient photocatalytic removal of tetracycline antibiotic under visible light

Constructing a Type-II CdS/Bi2MoO6 Heterostructure: Promoting Photocatalytic Degradation of Contaminants

Constructing a heterostructure is regarded as one of the most favorable approaches to attaining the separation ability of photogenerated carriers and strengthening photocatalysis efficiency. In this study, a CdS/Bi2MoO6 type-II heterostructure was constructed through a hydrothermal technique. The photocatalytic test result shows that the degradation efficiency of rhodamine B (RhB) and tetracycline (TC) over CS/BMO-1 was 100 and 92% under visible light, respectively, which is the highest compared to other samples. The exceptional photocatalytic efficiency is principally associated with generating an inherent electric field within a type-II heterostructure, effectively restraining the recombination of photogenerated electron hole pairs. The intermediate products during the photocatalytic degradation of RhB and TC were identified through liquid chromatography-mass spectrometry, and the hypotheses were formulated regarding the corresponding photodegradation mechanisms. Furthermore, the outcomes of capture tests exhibited that the primary active species were •O2- and h+, and a mechanism of the photocatalytic degradation procedure has been proposed.

Defect-engineered dual Z-scheme core-shell MoS2/WO3-x/AgBiS2 for antibiotic and dyes degradation in photo and night catalysis: Mechanism and pathways

Water pollution caused by antibiotics and synthetic dyes and imminent energy crises due to limited fossil fuel resources are issues of contemporary decades. Herein, we address them by enabling the multifunctionality in dual Z-scheme MoS2/WO3-x/AgBiS2 across photolysis, photo Fenton-like, and night catalysis. Defect, basal, and facet-engineered WO3-x is modified with MoS2 and AgBiS2, which extended its photoresponse from the UV-NIR region, inhibited carrier recombination, and reduced carrier transfer resistance. The electric field rearrangement leads to a flow of electrons from MoS2 and AgBiS2 to WO3-x and intensifies the electron population, which is crucial for night catalysis. When MoS2/WO3-x/AgBiS2 was employed against doxycycline hydrochloride (DOXH), it removed 95.65, 81.11, and 77.92 % of DOXH in 100 min during photo-Fenton (PFR), night-Fenton (NFR), and photocatalytic (PCR) reactions, respectively. It also effectively removed 91.91, 98.17, 99.01, and 98.99 % of rhodamine B (RhB), Congo red (CR), methylene blue (MB), and methylene orange (MO) in Fenton reactions, respectively. ESR analysis consolidates the ROS generation feature of MoS2/WO3-x/AgBiS2 using H2O2 with and without irradiation. This work provides a strategy to eliminate the deficiencies of WO3-x and is conducive to the evolution of applications seeking to combat environmental and energy crises.

Metal-organic framework heterojunctions for photocatalysis

Heterojunctions combining two photocatalysts of staggered conduction and valence band energy levels can increase the photocatalytic efficiency compared to their individual components. This activity enhancement is due to the minimization of undesirable charge recombination by the occurrence of carrier migration through the heterojunction interface with separated electrons and holes on the reducing and oxidizing junction component, respectively. Metal-organic frameworks (MOFs) are currently among the most researched photocatalysts due to their tunable light absorption, facile charge separation, large surface area and porosity. The present review summarizes the current state-of-the-art in MOF-based heterojunctions, providing critical comments on the construction of these heterostructures. Besides including examples showing the better performance of MOF heterojunctions for three important photocatalytic processes, such as hydrogen evolution reaction, CO2 photoreduction and dye decolorization, the focus of this review is on describing synthetic procedures to form heterojunctions with MOFs and on discussing the experimental techniques that provide evidence for the operation of charge migration between the MOF and the other component. Special attention has been paid to the design of rational MOF heterojunctions with small particle size and controlled morphology for an appropriate interfacial contact. The final section summarizes the achievements of the field and provides our views on future developments.

Fluorescent and smartphone imaging detection of tetracycline residues based on luminescent europium ion-functionalized the regular octahedral UiO-66-NH2

Antibiotic residues cause extensive damage to food security, thus arousing serious concerns. Hence, rapid and sensitive detection of antibiotic residues is crucial to food safety. This study aimed to propose a portable, visual, intelligent and rapid method for tetracycline detection. We developed a ratiometric fluorescent sensor based on the Eu3+-functionalized regular octahedral UiO-66-NH2 material. The developed sensor could quantify tetracycline in the concentration range of 0.5-200 μM with a detection limit as low as 0.2 μM under the optimum conditions. Furthermore, the analytical results obtained using the designed sensor in the actual samples were basically consistent with those obtained using high-performance liquid chromatography. Based on these achievements, a smartphone application-integrated fluorescent testing paper was designed for facile, intelligent, and visual detection of tetracycline. The integrated portable sensor not only saved cost and time for testing but also provided a forward-looking approach to fast, sensitive detection of antibiotic residues.

Construction of urchin-like core-shell Fe/Fe2O3@UiO-66 hybrid for effective tetracycline reduction and photocatalytic oxidation

Although Fe/Fe2O3 has potential application compared with nanoscale zero-valent iron (nZVI), its smooth structure largely limits the catalytic performance. To address this challenge, we innovatively constructed highly efficient composite Fe/Fe2O3@UiO-66 via employing an urchin-like core-shell structure of Fe/Fe2O3 onto UiO-66 through a facile ion exchange precipitation method without inert gas protection. The characterization results show the urchin-like core-shell configuration can extend the life span of Fe0 and produce more active sites. Besides, the absorption spectrum is broadened by Fe2O3 which has narrow band gap and the high-efficiency separation of photogenerated electron-hole pairs is obtained with the load of Fe/Fe2O3. Moreover, Two-parameter pseudo-first-order decay model fits well with the reduction and adsorption of composites in the dark reaction, and a plausible pathway for tetracycline (TC) degradation is also proposed. The findings of this research provide a promising method for promoting the catalytic properties of MOF-based materials and Fe/Fe2O3.

Optimization of Visible-Light-Driven Ciprofloxacin Degradation Using a Z-Scheme Semiconductor MgFe2O4/UiO-67

A heterogeneous photocatalyst, MgFe2O4/UiO-67 (MU-x), was successfully synthesized by doping magnetic magnesium ferrite nanoparticles (MgFe2O4) with the UiO-67 metal-organic framework at various weight ratios (MgFe2O4: UiO-67 at 30, 50, 70, and 90 wt %). Various techniques, including X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) , Brunauer-Emmett-Teller (BET), photoluminescence (PL), vibrating sample magnetometry (VSM), electrochemical impedance spectroscopy (EIS), and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS), were used to characterize the prepared photocatalysts. The photocatalytic performance of MU-x in the degradation of ciprofloxacin (CIP) under visible light was assessed. The CIP degradation efficiency was found to increase as the amount of MgFe2O4 in the composite was increased up to 70 wt %. Experimental conditions were optimized using response surface methodology (RSM) based on central composite design (CCD) with three factors: initial pH, catalyst loading, and CIP concentration. Using the obtained model, the optimal conditions were determined as follows: initial pH of 8.025, catalyst loading of 33.8 wt %, and CIP concentration of 10.8 mg/L. Under these optimal conditions, a notable improvement was achieved, with 99.62% of CIP removal achieved within 90 min, surpassing the performance of previously reported photocatalysts. Total organic carbon (TOC) analysis revealed a high degree of mineralization, at 81.25%. The degradation pathway of CIP was investigated based on liquid chromatography-mass spectrometry (LC-MS) analysis. Finally, the values of ECB and EVB of the photocatalyst were determined and the possible degradation mechanism of CIP was investigated based on Mott-Schottky and the applied scavengers. The hydroxyl radical (•OH) was identified as the dominant species in the removal of CIP through a trapping experiment. The photocatalyst with 70 wt % of MgFe2O4 (MU-70) exhibited excellent stability and recoverability with an external magnet, demonstrating 86.33% CIP removal after four cycles. According to the obtained results, MU-70 is a promising visible-light-active photocatalyst with great potential for water treatment applications and convenient recovery.

Novel visible-light-active P-g-CN-based α-Bi2O3/WO3 ternary photocatalysts with a dual Z-scheme heterostructure for the efficient decomposition of refractory ultraviolet filters and environmental hormones: Benzophenones

The ubiquitous and refractory benzophenone (BP)-type ultraviolet filters, which are also endocrine disruptors, were commonly detected in the aquatic matrix and could not be efficiently removed by conventional wastewater treatment processes, thus causing extensive concern. Herein, a novel ternary nanocomposite, P-g-CN/α-Bi2O3/WO3 (P-gBW), was successfully fabricated by mixing cocalcinated components and applied to the decomposition of BP-type ultraviolet filters. The dual-Z-scheme heterostructure of P-gBW enhances visible-light absorption, efficiently facilitates separation and mobility, and prolongs the lifetime of photoinduced charge carriers via double charge transfer mechanisms. The optimum 95 wt% P-gBW exhibited excellent photocatalytic activity, degrading 96% 4-hydroxy benzophenone (4HBP) within 150 min and 93% 2,2',4,4'-tetrahydroxybenzophenone (BP-2) within 100 min under visible-light illumination, respectively. The pseudo-first-order rate constant of 4HBP (1.15 h-1) was 6.8-, 3.1-, 3.3- and 2.2-fold higher than those of WO3, P-g-CN, α-Bi2O3, and P-g-CN/α-Bi2O3, respectively, while that of BP-2 (1.71 h-1) was 5.2-, 2.2-, 3.2- and 1.5-fold higher, respectively. The improved photocatalytic degradation was attributed to efficient photoinduced charge carrier separation and migration and prevented the recombination of electron holes, as verified by photoluminescence, transient photocurrent response, and electrochemical impedance spectroscopy. Trapping experiments, electron paramagnetic resonance, and band energy position indicated an efficient dual-Z-scheme heterostructure.

Comparative study for removal of cationic and anionic dyes using alginate-based hydrogels filled with citric acid-sawdust/UiO-66-NH2 hybrid

Nowadays, a big challenge is developing a sustainable and effective method for removing contaminants like dyes from aqueous solutions. In this regard, Zr-based metal-organic framework (UiO-66-NH₂) and sawdust as the ideal adsorbents were used. Due to their low separation in adsorption processes, embedding into alginate and obtaining composite beads are suggested as a suitable strategy. The achieved Ca-alginate/citric acid (CA)-sawdust/UiO-66-NH₂ hydrogel beads were used to compare cationic and anionic dyes removal. This sorbent indicated an excellent selectivity for removing methylene blue versus methyl orange in a binary system. pH = 6, adsorbent amount = 80 mg, methylene blue concentration = 10 mg/L, and contact time = 420 min were achieved as optimal parameters on methylene blue adsorption with an adsorption capacity of about 26 mg/g. The removal process of methylene blue followed linear Freundlich isotherm and nonlinear pseudo-2nd-order kinetic models. The regeneration test demonstrated methylene blue removal efficiency higher than about 89 % after 9 cycles. According to the outcomes, methylene blue could be attached to the adsorbent surface through the electrostatic, hydrogen bonding, and π-π interactions of the aromatic rings. These results confirm the potential of Ca-alginate/CA-sawdust/UiO-66-NH₂ hydrogel beads as a selective bio-sorbent for cationic dye removal.

In-situ fabrication of ionic liquids/MIL-68(In)-NH2 photocatalyst for improving visible-light photocatalytic degradation of doxycycline hydrochloride

Metal-organic framework (MOFs)-based composites have been popular in photocatalysis due to their outstanding physicochemical properties, such as large surface area, high activity and good transmission properties. Herein, a method of ionic liquids (ILs)-assisted synthesis of IL/MIL-68(In)-NH₂ composite materials were proposed, and composites were used for visible light catalytic degradation of doxycycline hydrochloride (DOXH). The effects of four kinds of ionic liquids on the structure and photocatalytic properties of the composites were explored, including diethylenetriamine acetate ([DETA][OAc]), diethylenetriamine hexafluorophosphate ([DETA][PF₆]), 1-ethyl-3-methylimidazole acetate ([EMIM][OAc]) and 1-ethyl-3-methylimidazole hexafluorophosphate ([EMIM][PF₆]). The results show that the introduction of different ionic liquids affects the grain growth of MOFs material and photocatalytic activity. Among them, IL_DAc/MIL-68(In)-NH₂ samples showed the highest photocatalytic activity. 92% removal rate of doxycycline hydrochloride and kinetic degradation constant (0.00918 min^-1) was observed under the optimal addition of IL_DAc (10 wt%), which was 4.6 times that of MIL-68(In)-NH₂. The enhancement was attributed to a combined effect of efficient adsorption at low concentration, an increase of active sites, and efficient charge transfer. In addition, the effects of pH and initial concentration were investigated. Finally, the photocatalytic mechanism of DOXH was elucidated, and the possible intermediate products and degradation pathways were discussed. Considering the excellent photostability and ultra-fast photodegradation of IL_DAc/MIL-68(In)-NH₂, this study opens up a new prospect for the preparation of ionic liquids functionalized MOFs with wide practical application value.

CuO loaded ZnS nanoflower entrapped on PVA-chitosan matrix for boosted visible light photocatalysis for tetracycline degradation and anti-bacterial application

Novel photocatalyst CuO loaded ZnS nanoflower supported on carbon frame work PVA/Chitosan was synthesized by co-precipitation and ultrasonic assisted method. The co-existence of ZnS and CuO and its crystallinity in nanohybrid was verified by XRD, SAED and HR-TEM analysis. The availability of defects in ZnS was identified by EPR. FTIR and TGA verified the presence of PVA and Chitosan. Defects mediated ZnS-CuO/PVA/chitosan heterojunction promote synergistic charge separation with type II interface. Zn-vacancy facilitates two-photon excitation that improves visible-light harvesting. The photocatalytic activity of ZnS-CuO/PVA/Chitosan was 94.7% which is higher when compared to ZnS (40%) and CuO (60%). The photocatalytic mechanism was elucidated using scavenger test and both ·O₂^- and ·OH were found to play key role in tetracycline degradation. In addition, ZnS-CuO/PVA/Chitosan demonstrated efficient anti-microbial effect against the both gram strains on comparing with individual ZnS and CuO. Thus, the multifunctional ZnS-CuO/PVA/Chitosan is promising for the photocatalytic degradation of tetracycline and as an antimicrobial agent.