Molecularly imprinted colloidal array with multi-boronic acid sites for glycoprotein detection under neutral pH

Facile fabricate sandwich-structured molecularly imprinted dopamine polymer for simultaneously specific capture of Low-density lipoprotein and eliminate "bad cholesterol"

A simplified approach for preparation of sandwich type molecularly imprinted polymers (PPDA-MIPs) is proposed for simultaneously identify Low-density lipoprotein (LDL) and dispose "bad cholesterol". Porous polydopamine nanosphere (PPDA) is applied as a matrix for immobilization of LDL, and the imprinted layer is formed by dopamine acting as a functional monomer. Since imprinted cavities exhibit shape memory effects in terms of recognizing selectivity, the PPDA-MIPs exhibit excellent selectivity toward LDL and a substantial binding capacity of 550.3 μg mg-1. Meanwhile, six adsorption/desorption cycles later, the adsorption efficiency of 83.09 % is still achieved, indicating the adequate stability and reusability of PPDA-MIPs. Additionally, over 80 % of cholesterol is recovered, indicating the completeness of "bad cholesterol" removal in LDL. Lastly, as demonstrated by gel electrophoresis, PPDA-MIPs performed satisfactory behavior for the removal of LDL from the goat serum sample.

Fabrication of double imprinted anchor points in cellulose nanocrystals-based hierarchical porous polyHIPEs for selective separation of flavoniods under physiological pH

Previous research had proved that molecular imprinted polymers can be used as separation material for removing Naringin (NRG) from agricultural pomelo wastes effectively. But the adsorption amounts of NRG molecules from traditional MIPs was quite low by using boronic acid as functional monomer because of single affinity interaction. Therefore, we developed the new combination of bifunctional monomers (i.e. low pKa boronate affinity monomer 2,4-difluoro-3-formylphenylboronic acid and dopamine) based on cellulose nanocrystals (CNCs) mixed with polymerized high internal phase emulsion (polyHIPE, PH) through an double layer surface imprinted method. The introduction of polyethylenimine (PEI) can offer abundant anchor units for the growth of more anchor sites to immobilization template molecules. Importantly, largely improved selective adsorption amounts (50.79 μmol g-1), which may be attribute to the fabrication of the uniform growth of double imprinted layers onto the polydopamine (PDA)/boronic acid-based surfaces. In addition, the resulting double recognition molecular imprinted polymers (MIPs) based on hypercrosslinked PH (DR-HCLPH@MIPs) not only exhibited fast adsorption kinetic of NRG molecule, but also possessed excellent selectivity and high adsorption capacities at physiological pH. Meanwhile, the coarse NRG from pomelo waste can be high selectively extracted to 94.74%. Overall, this study provides a versatile approach for fabrication of the sandwich-biscuit-like double imprinting layer porous MIPs for precise identification and ultrafast transport separation of NRG from complex samples.

New modes of converting chemical information with colloidal photonic crystal sensing units

Photonic crystal is a kind of device which can convert a chemical signal into an optical signal and is commonly used in sensing and detection. The maximum reflection wavelength representing the photonic band gap has been the most common converting mode in analytical usage which however discard too much valuable chemical information. In this work, we established two additional modes for mining chemical information more deeply in time and space as the sensing information to distinguish analytes. They are respectively based on dynamic analysis of the spectrum shift and the distinction of the RGB partition block value information of optical image. The molecular imprinting sensing mechanism worked well on three organophosphorus compounds to the detection limit of 10-4 M. The principle component analysis of above data did present a good discrimination of organophosphorus analytes from interfering counter anions to a low detection limit of 10-6 M. To make the detection more convenient and to achieve real-time on-site detection, we have designed the portable photonic crystal signal acquisition kit. Together with the mobile terminal, the kit connects the optical image collected on site, the algorithm working on the cloud and the input/output interactive interface of users in detection. The methods were constructed on an example made of a three-dimensional molecularly imprinted photonic crystal hydrogels sensing unit targeting on organo-phosphides.

Cross-Linking of Sugar-Derived Polyethers and Boronic Acids for Renewable, Self-Healing, and Single-Ion Conducting Organogel Polymer Electrolytes

This report describes the synthesis and characterization of organogels by reaction of a diol-containing polyether, derived from the sugar d-xylose, with 1,4-phenylenediboronic acid (PDBA). The cross-linked materials were analyzed by infrared spectroscopy (FT-IR), thermal gravimetric analysis (TGA), scanning electron microscopy (FE-SEM), and rheology. The rheological material properties could be tuned: gel or viscoelastic behavior depended on the concentration of polymer, and mechanical stiffness increased with the amount of PDBA cross-linker. Organogels demonstrated self-healing capabilities and recovered their storage and loss moduli instantaneously after application and subsequent strain release. Lithiated organogels were synthesized through incorporation of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) into the cross-linked matrix. These lithium-borate polymer gels showed a high ionic conductivity value of up to 3.71 × 10^-3 S cm^-1 at 25 °C, high lithium transference numbers (t ₊ = 0.88-0.92), and electrochemical stability (4.51 V). The gels were compatible with lithium-metal electrodes, showing stable polarization profiles in plating/stripping tests. This system provides a promising platform for the production of self-healing gel polymer electrolytes (GPEs) derived from renewable feedstocks for battery applications.