Charge-driven interaction for adsorptive removal of organic dyes using ionic liquid-modified graphene oxide

Simultaneous adsorption of ciprofloxacin drug and methyl violet dye on boron nitride nanosheets: experimental and theoretical insights

In this study, hexagonal boron nitride (BN) with a sheet-like morphology is successfully synthesized by reacting borax (Na2B4O7·10H2O) and urea (CO(NH2)2) powders in air via a facile microwave-assisted method within a short reaction time (15 min). The as-prepared product is structurally characterized via Fourier transformation infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM), energy dispersion X-ray analyzer (EDX), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) surface area measurements. The adsorption process of methyl violet (MV) as a model of organic dyes and ciprofloxacin (CIP) as a model of antibiotics onto the boron nitride nanosheets has been experimentally and theoretically studied. The BN nanosheets exhibit the maximum adsorption capacity of 320.94 mg g-1 for MV dye and 266.29 mg g-1 for CIP antibiotic. The Freundlich isotherm model was suitable to describe the adsorption equilibrium isotherm data and the pseudo second-order model reflected the adsorption kinetics well. The calculated thermodynamic parameters show that the adsorption process is spontaneous under the measured conditions. The adsorption of CIP, MV and CIP + MV molecules on the surface of BN has been investigated through DFT calculations. The charge transfer and high adsorption capacity demonstrate the potential of BN nanosheets as an adsorbent for the simultaneous removal of MV dye and CIP drug from contaminated water.

Eco-friendly cellulose-based hydrogel functionalized by NIR-responsive multimodal antibacterial polymeric ionic liquid as platform for promoting wound healing

With the trend of sustainable development and the complex medical environment, there is a strong demand for multimodal antibacterial cellulose wound dressing (MACD) with photothermal therapy (PTT). Herein, a novel MACD fabrication strategy with PTT was proposed and implemented through graft polymerization of an imidazolium ionic liquid monomer containing iron complex anion structure. The fabricated hydrogels exhibited excellent antibacterial properties because of the efficient photothermal conversion ability (68.67 %) of ionic liquids and the intrinsic structural characteristic of quaternary ammonium salts. The antibacterial ratio of cellulosic hydrogel dressings to S. aureus and E. coli could reach 99.57 % and 99.16 %, respectively. Additionally, the fabricated hydrogels demonstrated extremely low hemolysis rates (<5 %) and excellent cell viability (~>85 %). Furthermore, in vivo antibacterial experimental results proved that the fabricated antibacterial dressings could significantly accelerate wound healing. Therefore, the proposed strategy would provide a new method of designing and preparing high-performance cellulose wound dressings.

Biocompatible cellulose acetate supported ammonium based ionic liquid membranes; way forward to remediate water pollution

Dyes contaminated water has caused various environmental and health impacts in developing countries especially Pakistan due to different industrial activities. This issue has been addressed in present study by fabricating biocompatible ionic liquid (IL) membranes for the remediation of Crystal violet (CV) dye from contaminated water. Novel ammonium-based IL such as Triethyl dimethyl ammonium sulfate ([C3A][C2H6]SO4); (A2) was synthesized and further functionalized with hydroxyapatite (HAp; extracted from refused fish scales) resulting in the formation of HA2. Furthermore, A2 and HA2 were then used to fabricate the cellulose acetate (CA) based membranes with different volume ratios. The physicochemical properties of membranes-based composite materials were investigated using FTIR, XRD, and TGA and used for the adsorption of CV in the closed batch study. In results, CA-HA2 (1:2) showed higher efficiency of 98% for CV reduction, after the contact time of 90 min. Kinetic studies showed that the adsorption of CV followed the pseudo-second-order kinetic model for all adsorbents. The antibacterial properties of the synthesized membrane were investigated against gram-positive strain, S. aureus and CA-A2 (1:1) showed better antibacterial properties against S. aureus. The developed membrane is sustainable to be used for the adsorption of CV and against bacteria.

Combination mechanism of the ternary composite based on Fe3O4-chitosan-graphene oxide prepared by solvothermal method

Magnetic nanohybrid combining chitosan and graphene have demonstrated promising application in environmental remediation. Herein, ternary composite MCG based on Fe₃O₄, chitosan (CS) and graphene oxide (GO) was facilely prepared via solvothermal method. The as prepared composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), Raman, Brunauer/Emmett/Teller-Barret/Joyner/Halenda (BET-BJH) and thermo gravimetric-differential thermal analysis (TG-DTA). The combination mechanism of MCG was unveiled via employing the hard-soft acid-base (HSAB) theory and spectroscopic investigations including X-ray photoelectron spectroscopy (XPS), Ultraviolet-visible (UV-Vis) and fluorescent emission spectra. Particularly, combination mechanism of MCG was elucidated by the probable site to site interaction of the couplet components in MCG, as follows. (1) CS-Fe₃O₄. The primary interaction is N(NH₂)-Fe(III), electron donates from N to Fe, transforming one half of the amino groups of chitosan into positive N⁺. (2) GO-CS. Amidation reaction is the primary interaction form, converting the other half of the amino groups of chitosan into -C(O)NH-. (3) GO-Fe₃O₄. Dominant interactions are those of epoxy, hydroxyl and aromatic ring with Fe(III). Moreover, MCG exhibits fair adsorption performance on divalent heavy metals in six consecutive cycles. These explorations may shed light on the design of efficient adsorbent based on Fe₃O₄-chitosan-graphene architecture.

Ionic modification of graphene nanosheets to improve anti-corrosive properties of organosilicon composite coatings†

Composite coatings with anti-corrosive properties were fabricated using quaternized silicone oil modified graphene oxide and silicone polymer. Quaternized silicone oil was successfully synthesized through copolymerization of octamethyl cyclotetrasiloxane (D4), chloropropylsilane and triethylamine. The quaternized silicone oil modified graphene oxide (M-GO) was characterized by using ¹H NMR, FT-IR, Small-angle X-ray scattering (SAXS), Thermogravimetry (TG) and Transmission electron microscopy (TEM). The results showed that the M-GO was formed successfully. The M-GO could be dispersed without aggregation in some organic solvents, and the concentration of M-GO could be up to 3 mg ml⁻¹. The M-GO-reinforced silicone composites exhibited obvious improvements in thermal stability, mechanical properties and especially anticorrosive properties with the highest E_corr (−121 mV) and the lowest I_corr (6.058 × 10⁻⁹ A cm⁻²), and the protection efficiency of the matrix could reach 99.97%. The anticorrosive mechanism of the fabricated composite coatings was investigated. This work provides a ready strategy for modification of GO and fabrication of high performance graphene-based silicone composite materials.

Silicone modified graphene oxide (M-GO) was readily and visually prepared. The M-GO-reinforced silicone composite coating exhibited obvious improvements in thermal stability, mechanical properties, especially anticorrosion.

Citric, succinic, and vanillic acid-functionalized magnetic-cored dendrimer for methylene blue adsorption

A new functional composite was synthesized in this study comprising magnetic-cored dendrimer (MCD) modified with citric acid (CA), succinic acid (SA), and vanillic acid (VA) terminal groups. The CA-MCD, SA-MCD, and VA-MCD exhibited average particle size of 8-18 nm and superparamagnetic behavior. Adsorption potential of the composite was assessed by monitoring methylene blue (MB) removal from contaminated water. The CA-MCD attained adsorption equilibrium in 30 min while SA-MCD and VA-MCD achieved equilibrium in 60 min. The Langmuir model better fitted the adsorption results than the Freundlich model, indicating a monolayer mode of MB adsorption on the composite. Maximum adsorption capacity of CA-MCD, SA-MCD, and VA-MCD was 216.30 mg/g, 184.29 mg/g, and 196.58 mg/g, respectively. The CA-MCD exhibited best adsorption performance by removing 99% MB at pH = 11. In reusability experiments, the CA-MCD, SA-MCD, and VA-MCD maintained over 90% MB adsorption for both 15 mg/L and 50 mg/L solutions in the third cycle. Overall, the organic acid-functionalized MCDs with high adsorption capacity and reusability potential showed utility for practical application for wastewater decontamination.

Ionic liquid based composites: A versatile materials for remediation of aqueous environmental contaminants

Water pollution is one of the most aggravated problems threatening the sustainability of human race and other life forms due to the rapid pace of civilization and industrialization. A long history exists of release of hazardous pollutants into the water bodies due to selfish human activities since the Industrial Revolution, but no effort has been completely successful in curbing the activities that result in the degradation of our environment. These pollutants are harmful, carcinogenic and have adverse health effects to all forms of life. Thus, remarkable efforts have been geared up to obtain clean water by exploiting science and technology. The application of Ionic liquids (ILs) as sustainable materials have received widespread attention since the last decade. Their interesting properties, simplicity in operation and satisfactory binding capacities in elimination of the contaminants makes them a valuable prospect to be utilized in wastewater treatment. Immobilizing and grafting the solid supports with ILs have fetched efficient results to exploit their potential in the adsorptive removal processes. This review provides an understanding of the recent developments and outlines the possible utility of IL based nano adsorbents in the removal of organic compounds, dyes and heavy metal ions from aqueous medium. Effect of several parameters such as sorbent dosage, pH and temperature on the removal efficiency has also been discussed. Moreover, the adsorption isotherms, thermodynamics and mechanism are comprehensively studied. It is envisioned that the literature gathered in this article will guide the budding scientists to put their interest in this area of research in the days to come.

Flexible Nano-TiO2 Sheets Exhibiting Excellent Photocatalytic and Photovoltaic Properties by Controlled Silane Functionalization-Exploring the New Prospects of Wastewater Treatment and Flexible DSSCs

TiO₂ nanoparticles surface-modified with silane moieties, which can be directly coated on a flexible substrate without the requirement of any binder materials and postsintering processes, are synthesized and characterized using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy, Raman spectroscopy, photoluminescence spectroscopy, time-correlated single-photon counting, and transmission electron microscopy. The viability of the prepared surface-modified TiO₂ (M-TiO₂) sheets as a catalyst for the photo-induced degradation of a model dye, methylene blue, was checked using UV-visible absorption spectroscopy. The data suggest that, compared to unmodified TiO₂, M-TiO₂ sheets facilitate better dye-degradation, which leads to a remarkable photocatalytic activity that results in more than 95% degradation of the dye in the first 10 min and more than 99% of the degradation in the first 50 min of the photocatalytic experiments. We also demonstrate that M-TiO₂ can be recycled with negligible reduction in photocatalytic activity. Further, the photovoltaic properties of the developed M-TiO₂ sheets were assessed using UV-visible absorption spectroscopy, electrochemical impedance spectroscopy (EIS), and photochronoamperometry. Dye-sensitized solar cells (DSSC) fabricated using M-TiO₂ as the photoanode exhibited a photoconversion efficiency of 4.1% under direct sunlight. These experiments suggested that M-TiO₂ sheets show enhanced photovoltaic properties compared to unmodified TiO₂ sheets, and that, when N-719 dye is incorporated, the dye-TiO₂ interaction is more favorable for M-TiO₂ than bare TiO₂. The simple solution processing method demonstrated in this paper rendered a highly flexible photoanode made of M-TiO₂ with superior charge-separation efficiency to an electrode made of bare TiO₂. We propose that our findings on the photovoltaic properties of M-TiO₂ open up arenas of further improvement and a wide scope for the large-scale production of flexible DSSCs on plastic substrates at room temperature in a cost-effective way.

Enhancing the Dye-Rejection Efficiencies and Stability of Graphene Oxide-Based Nanofiltration Membranes via Divalent Cation Intercalation and Mild Reduction

Laminar graphene oxide (GO) membranes have demonstrated great potential as next-generation water-treatment membranes because of their outstanding performance and physicochemical properties. However, solute rejection and stability deterioration in aqueous solutions, which are caused by enlarged nanochannels due to hydration and swelling, are regarded as serious issues in the use of GO membranes. In this study, we attempt to use the crosslinking of divalent cations to improve resistance against swelling in partially reduced GO membranes. The partially reduced GO membranes intercalated by divalent cations (i.e., Mg2+) exhibited improved dye-rejection efficiencies of up to 98.40%, 98.88%, and 86.41% for methyl orange, methylene blue, and rhodamine B, respectively. In addition, it was confirmed that divalent cation crosslinking and partial reduction could strengthen mechanical stability during testing under harsh aqueous conditions (i.e., strong sonication).

Fruit waste-derived cellulose and graphene-based aerogels: Plausible adsorption pathways for fast and efficient removal of organic dyes

A wide range of organic pollutants in industrial effluents, agricultural runoff, and domestic discharges are exacerbating water scarcity, leading to water-borne ailments, and adversely affecting the marine ecosystem and biodiversity. The efficient, sustainable, and cost-effective materials need to be addressed urgently for the removal of organic pollutants. Herein, ultra-light (0.018 g.cm^-3) and highly porous (96.4%) composite aerogel is prepared by gelatinization of graphene oxide with fruit waste-derived cellulose. The macroscopic porosity generated by interconnecting cellulosic skeleton and graphene oxide sheets via hydrogen bonding network provided ample avenues for transport and diffusion of organic dyes-enriched wastewater throughout the cellulose-graphene oxide composite aerogel (CGA). Consequently, organic dyes are efficiently adsorbed by easily accessible surface sites distributed throughout the CGA. The size, charge, and chemical structure of organic dyes along with textural features and accessible surface active sites of CGA governed the adsorption process. The spectroscopic analyses based on FTIR, Raman, and XPS measurements suggest electrostatic, n-π, π-π, cation-π interactions, dipole-dipole hydrogen, and Yoshida hydrogen linkages as major interactive pathways for the adsorption of organic dyes by the CGA. Moreover, the composite aerogel furnished an excellent recyclability for the adsorptive removal of organic pollutants from wastewater. The present work promises the potential of 2D nanostructured layered materials and fruit-waste-derived composite aerogels for sustainable utilization in wastewater treatment, which can be an excellent step towards water security.