Amine functionalized hierarchical bimodal mesoporous silicas as a promising nanocomposite for highly efficient CO2 capture

A novel amine functionalized porous geopolymer spheres from municipal solid waste incineration fly ash for CO2 capture

Municipal solid waste (MSW) incineration fly ash (FA) is classified as hazardous waste, and strategies for recycling FA have attracted attention. In this study, the porous geopolymer spheres (PGS) were prepared from FA by the foaming-suspension-solidification method, and then the PGS were functionalized with tetraethylenepentamine (TEPA) to capture CO2. The results showed that washing pretreatment and the addition of H2O2 foaming agent enhanced the pore volume and specific surface area of PGS. The CO2 adsorption capacity of amine-functionalized PGS exhibited a trend of increasing and then decreasing in the range of 35-80 °C. The maximum adsorption capacity of TEPA-WPGS3 was 2.55 mmol/g at 65 °C higher than expected for the average of TEPA and PGS. This was because PGS improved the dispersion of TEPA, thus exposing more active sites of TEPA and making it more likely to interact with CO2. The adsorption efficiency of amine-functionalized PGS decreased by only 2.4% after 10 cycles, indicating that it has excellent regeneration performance. In addition, amine-functionalized PGS, which showed excellent CO2 adsorption capacity, had a significant ability to selectively adsorb CO2 and the adsorption capacity of the rapid stage accounted for approximately 80% of the saturated adsorption capacity. This study shows that FA-derived geopolymers have excellent CO2 adsorption properties and provides a new method for the resource utilization of FA.

Liquid-in-Aerogel Porous Composite Allows Efficient CO2 Capture and CO2 /N2 Separation

The pursuit of efficient CO2 capture materials remains an unmet challenge. Especially, meeting both high sorption capacity and fast uptake kinetics is an ongoing effort in the development of CO2 sorbents. Here, a strategy to exploit liquid-in-aerogel porous composites (LIAPCs) that allow for highly effective CO2 capture and selective CO2 /N2 separation, is reported. Interestingly, the functional liquid tetraethylenepentamine (TEPA) is partially filled into the air pockets of SiO2 aerogel with left permanent porosity. Notably, the confined liquid thickness is 10.9-19.5 nm, which can be vividly probed by the atomic force microscope and rationalized by tailoring the liquid composition and amount. LIAPCs achieve high affinity between the functional liquid and solid porous counterpart, good structure integrity, and robust thermal stability. LIAPCs exhibit superb CO2 uptake capacity (5.44 mmol g-1 , 75 °C, and 15 vol% CO2 ), fast sorption kinetics, and high amine efficiency. Furthermore, LIAPCs ensure long-term adsorption-desorption cycle stability and offer exceptional CO2 /N2 selectivity both in dry and humid conditions, with a separation factor up to 1182.68 at a humidity of 1%. This approach offers the prospect of efficient CO2 capture and gas separation, shedding light on new possibilities to make the next-generation sorption materials for CO2 utilization.

The assembly of silica species with alkylamines: Mechanism of wastewater-free synthesis and the application of gel as a catalyst

Silica species generated by the hydrolysis and condensation of tetraethyl orthosilicate (TEOS) could assemble with alkylamines to form silica gel. Herein, it was evidenced that part of the added amines, including butylamine (BA), octylamine (OA) or dodecylamine (DA), was protonated in the mixture of water and ethanol. Therefore, besides the hydrogen bonding between neutral silica species and the micelles composed of the non-protonated amines (Tanev and Pinnavaia, 1995), there existed strong electrostatic attraction between negatively charged silica species and the micelles composed of the protonated amines. This coexisting assembly mechanism could explain why the uncalcined BA- and OA-gels were millimeter-sized small blocks with large porosities and synthesized without waste water emission, while the uncalcined DA-gel was almost non-porous and formed via precipitation from its reaction medium. The uncalcined BA gel was proved to be efficient as a solid basic catalyst, replacing the commonly used ammonia solution which is easily volatilized and has a pungent smell, for the hydrolysis and condensation of TEOS to prepare silica microspheres.

Study on the Printability through Digital Light Processing Technique of Ionic Liquids for CO2 Capture

Here we present new 3D printable materials based on the introduction of different commercially available ionic liquids (ILs) in the starting formulations. We evaluate the influence of these additives on the printability of such formulations through light-induced 3D printing (digital light processing-DLP), investigating as well the effect of ionic liquids with polymerizable groups. The physical chemical properties of such materials are compared, focusing on the permeability towards CO2 of the different ILs present in the formulations. At last, we show the possibility of 3D printing high complexity structures, which could be the base of new high complexity filters for a more efficient CO2 capture.