Effect of carbon dioxide on thermal treatment of food waste as a sustainable disposal method

Unlocking high-performance HCl adsorption at elevated temperatures: the synthesis and characterization of robust Ca-Mg-Al mixed oxides

The presence of HCl and SO2 gas imposes limitations on syngas utilization obtained from household waste in a wide range of applications. The hydrotalcite-like compounds (HTLs) have been proved that could remove HCl efficiency. However, the research on impact of synthesis conditions of HTLs and SO2 on HCl removal was limited. In this study, a range of Ca-Mg-Al mixed oxide sorbents was synthesized by calcining HTLs, with variations in crystallization temperature, solution pH, and the Ca/Mg molar ratio. These sorbents were examined for their effectiveness in removing HCl at medium-high temperatures under diverse conditions. The adsorption performance of selected sorbents for the removal of HCl, SO2, and HCl-SO2 mixed gas at temperature of 350 °C, 450 °C, and 550 °C, respectively, was evaluated using thermogravimetric analysis (TGA). It was observed that the HTL synthesis parameters significantly influenced the HCl adsorption capacity of Ca-Mg-Al mixed oxides. Notably, HTLs synthesized at 60 °C, a solution pH of 10-11, and a Ca/Mg ratio of 4 exhibited superior crystallinity and optimal adsorption characteristics. For individual HCl and SO2 removal, temperature had a minor effect on HCl adsorption but significantly impacted SO2 adsorption rates. At temperatures above 550 °C, SO2 removal efficiency substantially decreased. When exposed to a mixed gas, the Ca-Mg-Al mixed oxides could efficiently remove both HCl and SO2 at temperatures below 550 °C, with HCl dominating the adsorption process at higher temperatures. This dual-action capability is attributed to several mechanisms through which HTL sorbents interacted with HCl, including pore filling, ion exchange, and cation exchange. Initially, HCl absorbed onto specific sites created by water and CO2 removal due to the surface's polarity. Subsequently, HCl reacted with CaCO3 and CaO formed during HTL decomposition.

Study on the effects of carbon dioxide atmosphere on the production of biochar derived from slow pyrolysis of organic agro-urban waste

Slow pyrolysis, a widely recognized thermochemical technique, is employed to produce biochar usually under inert atmospheres. Recently, there is a growing interest in utilizing CO2 as a carrier gas during pyrolysis as an alternative to inert atmospheres, aiming to modify the resulting pyrolytic products and make them suitable for different applications. This study investigated and compared the impact of CO2 atmosphere with N2 on pyrolysis of food waste, rice husk, and grape tree branches waste via slow pyrolysis at temperatures of 400, 500, and 600 °C at 5 and 15 °C/min for 1 h, to evaluate biochar production and its properties. The results demonstrate that CO2 atmosphere increased the biochar yield for all feedstocks and significantly influenced the physicochemical properties of biochar. Compared to N2, CO2-derived biochar exhibited less volatile matter, higher carbon content, lower O/H and O/C molar ratios and enhanced textural properties. This study highlighted the potential of utilizing CO2 for biochar production and tailoring biochar properties for specific applications and the findings contribute to the establishment of sustainable and efficient waste management systems and the production of value-added biochar products.

Effects of Ni/Al2O3 catalyst treatment condition on thermocatalytic conversion of spent disposable wipes

Municipal solid waste (MSW) management is an essential municipal service. Proper waste treatment is an important part of the waste management. Thermocatalytic waste upcycling has recently gained great interest and attention as a method to extract value from waste, which potentially substitutes traditional waste treatment methods. This study aims at demonstrating the potential for thermocatalytic waste upcycling using spent disposable wipes as an MSW surrogate. Two different Ni/Al2O3 catalysts were prepared, treated under two different atmospheres (N2 and CO2). The catalyst treated in N2 (Ni/Al2O3-N2) exhibited a higher surface metallic Ni site than the catalyst treated in CO2 (Ni/Al2O3-CO2). The use of the Ni/Al2O3-N2 increased the yield of gas pyrolysate and decreased the yield of byproduct (e.g., wax), compared with no catalyst and the Ni/Al2O3-CO2. In particular, the Ni/Al2O3-N2 catalyst affected the generation of gaseous hydrogen (H2) by increasing the H2 yield by up to 102% in comparison with the other thermocatalytic systems. The highest H2 yield obtained with the Ni/Al2O3-N2 was attributed to the most surface metallic Ni sites. However, the Ni/Al2O3-N2 catalyst led to char having a lower higher heating value than the other catalysts due to its lowest carbon content. The results indicated that the reduction treatment environment for Ni/Al2O3 catalyst influences thermocatalytic conversion product yields of spent disposable wipes, including enhanced H2 production.

Electronic Supplementary Material

Supplementary material is available in the online version of this article at 10.1007/s11814-023-1461-8.

Application of response surface methodology and artificial neural network for the preparation of Fe-loaded biochar for enhanced Cr(VI) adsorption and its physicochemical properties and Cr(VI) adsorption characteristics

In this study, we optimized and explored the effect of the conditions for synthesizing Fe-loaded food waste biochar (Fe@FWB) for Cr(VI) removal using the response surface methodology (RSM) and artificial neural network (ANN). The pyrolysis time, temperature, and Fe concentration were selected as the independent variables, and the Cr(VI) adsorption capacity of Fe@FWB was maximized. RSM analysis showed that the p-values of pyrolysis temperature and Fe concentration were less than 0.05, indicating that those variables were statically significant, while pyrolysis time was less significant due to its high p-value (0.2830). However, the ANN model results showed that the effect of pyrolysis time was more significant on Cr(VI) adsorption capacity than Fe concentration. The optimal conditions, determined by the RSM analysis with a lower sum of squared error than ANN analysis, were used to synthesize the optimized Fe@FWB (Fe@FWB-OPT) for Cr(VI) removal. From the equilibrium model fitting, the Langmuir model showed a better fit than the Freundlich model, while the Redlich-Peterson isotherm model overlapped. The Cr(VI) sorption capacity of Fe@FWB-OPT calculated from the Langmuir model was 377.71 mg/g, high enough to be competitive to other adsorbents. The kinetic Cr(VI) adsorption was well described by the pseudo-second-order and Elovich models. The XPS results showed that Cr adsorbed on the surface of Fe-FWB-OPT was present not only as Cr(VI) but also as Cr(III) by the reduction of Cr(VI). The results of Cr(VI) adsorption by varying the pH indicate that electrostatic attraction is a key adsorption mechanism.

Effects of torrefaction on product distribution and quality of bio-oil from food waste pyrolysis in N2 and CO2

Waste food utilization to produce bio-oil through pyrolysis has received increasing attention. The feedstock can be utilized more efficiently as its properties are upgraded. In this work, the mixed food waste (MFW) was pretreated via torrefaction at moderate temperatures (250-275 °C) under an inert atmosphere before fast pyrolysis. The pyrolysis of torrified MFW (T-MFW) was performed in a bubbling fluidized-bed reactor (FBR) to study the influence of torrefaction on the pyrolysis product distribution and bio-oil compositions. The highest liquid yield of 39.54 wt% was observed at a pyrolysis temperature of 450℃. The torrefaction has a significant effect on the pyrolysis process of MFW. After torrefaction, the higher heating values (HHVs) of the pyrolysis bio-oils (POs) ranged from 31.51 to 34.34 MJ/kg, which were higher than those of bio-oils from raw MFW (27.69-31.58 MJ/kg). The POs mainly contained aliphatic hydrocarbons (alkenes and ketones), phenolic, and N-containing derivatives. The pyrolysis of T-MFW was also carried out under the CO2 atmosphere. The application of CO2 as a carrier gas resulted in a decrease in the liquid yield and an increase in the gas product yield. In addition, the carbon and nitrogen content of POs increased, whereas the oxygen was reduced via the release of moisture and CO. Using CO2 in pyrolysis inhibited the generation of nitriles derivatives in POs, which are harmful to the environment. These results indicated that the application of CO2 to the thermal treatment of T-MFW could be feasible in energy production as well as environmental pollution control.

Effect of eggshell- and homo-type Ni/Al2O3 catalysts on the pyrolysis of food waste under CO2 atmosphere

This study highlights the potential of pyrolysis of food waste (FW) with Ni-based catalysts under CO₂ atmosphere as an environmentally benign disposal technique. FW was pyrolyzed with homo-type Ni/Al₂O₃ (Ni-HO) or eggshell-type Ni/Al₂O₃ (Ni-EG) catalysts under flowing CO₂ (50 mL/min) at temperatures from 500 to 700 °C for 1 h. A higher gas yield (42.05 wt%) and a lower condensable yield (36.28 wt%) were achieved for catalytic pyrolysis with Ni-EG than with Ni-HO (34.94 wt% and 40.06 wt%, respectively). In particular, the maximum volumetric content of H₂ (21.48%) and CO (28.43%) and the lowest content of C₂-C₄ (19.22%) were obtained using the Ni-EG. The formation of cyclic species (e.g., benzene derivatives) in bio-oil was also effectively suppressed (24.87%) when the Ni-EG catalyst and CO₂ medium were concurrently utilized for the FW pyrolysis. Accordingly, the simultaneous use of the Ni-EG catalyst and CO₂ contributed to altering the carbon distribution of the pyrolytic products from condensable species to value-added gaseous products by facilitating ring-opening reactions and free radical mechanisms. This study should suggest that CO₂-assisted catalytic pyrolysis over the Ni-EG catalyst would be an eco-friendly and sustainable strategy for disposal of FW which also provides a clean and high-quality source of energy.

COVID-19 mask waste to energy via thermochemical pathway: Effect of Co-Feeding food waste

In this study, co-pyrolysis of single-use face mask (for the protection against COVID-19) and food waste was investigated for the purpose of energy and resource valorization of the waste materials. To this end, disposable face mask (a piece of personal protective equipment) was pyrolyzed to produce fuel-range chemicals. The pyrolytic gas evolved from the pyrolysis of the single-use face mask consisted primarily of non-condensable permanent hydrocarbons such as CH₄, C₂H₄, C₂H₆, C₃H₆, and C₃H₈. An increase in pyrolysis temperature enhanced the non-condensable hydrocarbon yields. The pyrolytic gas had a HHV of >40 MJ kg^-1. In addition, hydrocarbons with wider carbon number ranges (e.g., gasoline-, jet fuel-, diesel-, and motor oil-range hydrocarbons) were produced in the pyrolysis of the disposable face mask. The yields of the gasoline-, jet fuel-, and diesel-range hydrocarbons obtained from the single-use mask were highest at 973 K. The pyrolysis of the single-use face mask yielded 14.7 wt% gasoline-, 18.4 wt% jet fuel-, 34.1 wt% diesel-, and 18.1 wt% motor oil-range hydrocarbons. No solid char was produced via the pyrolysis of the disposable face mask. The addition of food waste to the pyrolysis feedstock led to the formation of char, but the presence of the single-use face mask did not affect the properties and energy content of the char. More H₂ and less hydrocarbons were produced by co-feeding food waste in the pyrolysis of the disposable face mask. The results of this study can contribute to thermochemical management and utilization of everyday waste as a source of energy.

Pyrolysis synergy of municipal solid waste (MSW): A review

The synergistic pyrolysis of municipal solid waste (MSW) were recently explored. This review aims to provide an overview on the synergistic pyrolysis studies of MSW, focusing on the synergy occurred during co-pyrolysis of different constituents of MSW. The interactions of intermediates released during pyrolysis can shift end product distributions, accelerate pyrolysis rates, and preferred production of specific compounds, which were categorized into four basic types with discussions. The pyrolysis synergy is proposed to be the key for success of pyrolytic practice of MSW that can handle the waste with maximal resource recovery and minimal carbon emission.

Synthesis of Fe-impregnated biochar from food waste for Selenium(Ⅵ) removal from aqueous solution through adsorption: Process optimization and assessment

Iron-impregnated food waste biochar (Fe-FWB) was synthesized for Se(Ⅵ) removal from aqueous solution. The effect and interactive effects of different parameters including pyrolysis time, temperature, and Fe concentration were explored using response surface methodology (RSM) to enhance conditions to achieve the highest Se(Ⅵ) removal using Fe-FWB. Pyrolysis time was not significant for Se(Ⅵ) adsorption capacity of Fe-FWB, but temperature and Fe concentration were found to be significant. The highest adsorption was achieved at 3.47 h and 495.0 °C with an Fe concentration of 0.44 M. Fe-FWB synthesized under optimum conditions were used to investigate the kinetic, equilibrium, and thermodynamic adsorption of Se(Ⅵ). Se(Ⅵ) adsorption reached equilibrium within 6 h, and both pseudo-second order and pseudo-first order models were suitable for describing kinetic Se(Ⅵ) adsorption. The Freundlich model was found to suitably fit the equilibrium adsorption data than the Langmuir model. The highest adsorption capacity of Fe-FWB for Se(Ⅵ) was 11.7 mg g^-1. Se(Ⅵ) adsorption on Fe-FWB was endothermic and spontaneous. The enthalpy change for Se(Ⅵ) adsorption was 54.4 kJ mol^-1, and the entropy change was negative at 15-35 °C. The increment of solution pH from 3 to 11 decreased the Se(Ⅵ) adsorption from 19.2 to 7.4 mg g^-1. The impact of interfering anions on Se(Ⅵ) adsorption followed the lineup: HCO₃^- > HPO₄^2- > SO₄^2- > NO₃^-. When compared to some adsorbents, the adsorption capacity of Se(Ⅵ) onto Fe-FWB was comparable even at neutral pH and the Fe-FWB was granular. These results indicate that Fe-FWB has prospective application in the removal of Se(Ⅵ) from aqueous solutions.

Catalytic Pyrolysis as a Technology to Dispose of Herbal Medicine Waste

The use of herbal medicine has increased tremendously over the last decades, generating a considerable amount of herbal medicine waste. Pyrolysis is a promising option to dispose of biomass and organic waste such as herbal medicine waste. Herein, an activated carbon-supported Pt catalyst (Pt/AC) and carbon dioxide (CO2) were applied to the pyrolysis of real herbal medicine waste to develop a thermal disposal method to prevent the formation of benzene derivatives that are harmful to the environment and human health. When using the Pt/AC catalyst in the pyrolysis of the herbal medicine waste at 500 °C, the generation of benzyl species was suppressed. This was likely because the Pt catalytic sites accelerate a free radical mechanism that is dominant in the thermal cracking of carbonaceous substances. However, the employment of CO2 (instead of typically used N2) as a pyrolysis medium for the herbal medicine waste pyrolysis did not decrease the concentrations of benzyl compounds contained in the pyrolytic products of the herbal medicine waste. This study might help develop a method to thermally dispose of agricultural biowaste, preventing the formation of harmful chemicals to the environment and human beings.

Pyrolysis of food waste over a Pt catalyst in CO2 atmosphere

In this study, a method of disposing food waste is introduced via catalytic pyrolysis under CO₂ condition. The catalyst and CO₂ hindered the generation of condensable compounds, leading to enhancing non-condensable gas generation. However, they did not affect the amount of solid residues left after the thermal reaction. The amount of condensable cyclic compounds was reduced when the catalyst and/or CO₂ were used. The enhancement of non-condensable gas production and reduction of cyclic compounds formation were maximized when the Pt catalyst and CO₂ were simultaneously applied to the pyrolysis of food waste. For instance, approximately 67.3 % less cyclic compounds, including benzene derivatives, were generated at 700 °C in the presence of the catalyst under a CO₂ atmosphere compared to non-catalytic conditions without CO₂. The results suggest that a CO₂-assisted catalytic pyrolysis is as environmentally benign disposal method for food waste.

Reduction of polycyclic compounds and biphenyls generated by pyrolysis of industrial plastic waste by using supported metal catalysts: A case study of polyethylene terephthalate treatment

The accumulation of industrial plastic waste in the environment is a global growing concern. Thermochemical process is a preferred method to dispose plastic waste mainly because it can reduce volume of the waste; however, the thermochemical disposal of plastic waste can emit harmful chemical species such as benzene derivatives and polycyclic hydrocarbons. As an effort to overcome this challenge, supported metal catalysts (carbon-supported Pd and Pt catalysts) were used to inhibit the formation of polycyclic compounds and biphenyl derivatives by pyrolysis of polyethylene terephthalate (PET). Less polycyclic compounds and biphenyl derivatives were generated during the Pd or Pt-catalyzed PET pyrolysis than non-catalytic PET pyrolysis. The concentrations of polycyclic compounds and biphenyl derivatives were 107 % and 56 % lower for the Pt-catalyzed pyrolysis at 700 °C than non-catalytic pyrolysis, respectively. The Pt catalyst was more effective to suppress the generation of polycyclic compounds and biphenyl derivatives during the PET pyrolysis than the Pd catalyst at temperatures from 400 to 800 °C. This was likely because the Pt sites catalyzes decyclization reaction and/or free radical mechanism that is dominant in thermal cracking of carbonaceous substances such as PET. The results of this study would help develop environmentally friendly industrial plastic waste treatment methods via thermochemical processes.

Effect of Pt catalyst on the condensable hydrocarbon content generated via food waste pyrolysis

A Pt catalyst supported on activated carbon (Pt/AC) was used for an environmentally friendly thermal treatment of food waste under an inert atmosphere (i.e., pyrolysis). This catalyst influenced the amounts of condensable hydrocarbons and noncondensable gases but not that of the solid remaining after the pyrolysis; in particular, it contributed to shifting the carbon distribution from the condensable hydrocarbons to the noncondensable gases for the food waste pyrolysis. Moreover, its use suppressed the generation of harmful chemical compounds, especially at high temperatures. For example, a Pt/AC-catalyzed pyrolysis at 700 °C produced about 4 times fewer benzene derivatives than the same treatment without a catalyst; this probably occurred because the Pt sites catalyzed the decyclization reaction and/or the free radical mechanism, which is dominant in the thermal cracking of carbon-containing feedstock. This study suggests that a Pt/AC-catalyzed pyrolysis would be a more environmentally benign food waste treatment method.

Pyrolysis of Polyethylene Terephthalate over Carbon-Supported Pd Catalyst

Pyrolysis of polyethylene terephthalate (PET) produces polycyclic hydrocarbons and biphenyl derivatives that are harmful to human health and the environment. Therefore, a palladium metal catalyst (5 wt.% Pd loaded on activated carbon) was used to prevent the formation of harmful materials. When a Pd catalyst/PET ratio of 0.01 was applied in pyrolysis of PET, it did not show a meaningful difference in the generation of polycyclic hydrocarbons and biphenyl derivatives. However, when a Pd catalyst/PET ratio of 0.05 was used during pyrolysis, it prevented their formation and generation at experimental temperature ranges (400–700 °C). For example, the concentration of 2-naphthalenecarboxylic acid produced, which is a typical polycyclic hydrocarbon material, was reduced by 44%. In addition, the concentration of biphenyl-4-carboxylic acid, which is contained in biphenyl derivatives, was reduced by 79% compared to non-catalytic pyrolysis at 800 °C. This was because the ring-opening reaction and free radical mechanism caused by the Pd catalyst and thermal cracking were dominant during the pyrolysis of PET. Apart from these materials, amine compounds were generated as products of the pyrolysis of PET. Amine concentration showed a similar trend with polycyclic hydrocarbons and benzene derivatives. Based on these results, the total concentration of polycyclic hydrocarbons and biphenyl derivatives was compared; the results confirmed that the concentrations of all substances were reduced. This research suggests that a metal-supported catalyst will help create a more environmentally friendly and reliable method of industrial plastic waste disposal.

Sustainable production of alkyl esters via thermal process in the presence of carbon black

In this study, it is introduced a sustainable synthetic route of alkyl esters, considered value-added industrial chemicals and fuels, from volatile fatty acids (VFAs) that can potentially be generated from organic waste. In the presence of a porous carbon material, the thermally induced reaction could be conducted under an initial pressure of 1 atm. Even though the reaction was finished within <10 s, they gave a high yield of target products: the conversion of six VFAs into their corresponding methyl esters which can be further converted into gasoline alternatives with >90 wt% yields. The carbon black showed better performance for both reactions than other commercially available porous material such as silica. This work suggests that carbon is a good option of being used as a porous material for thermal esterification to produce renewable alternative chemicals from waste-derived feedstocks.