Supercritical CO2-assisted impregnation of polylactic acid films with R-carvone: Effect of processing on loading, mass transfer kinetics, and final properties

Supercritical Impregnation of PETG with Olea europaea Leaf Extract: Influence of Operational Parameters on Expansion Degree, Antioxidant and Mechanical Properties

PETG (poly(ethylene glycol-co-cyclohexane-1,4-dimethanol terephthalate)) is an amorphous copolymer, biocompatible, recyclable, and versatile. Nowadays, it is being actively researched for biomedical applications. However, proposals of PETG as a platform for the loading of bioactive compounds from natural extract are scarce, as well as the effect of the supercritical impregnation on this polymer. In this work, the supercritical impregnation of PETG filaments with Olea europaea leaf extract was investigated, evaluating the effect of pressure (100-400 bar), temperature (35-55 °C), and depressurization rate (5-50 bar min-1) on the expansion degree, antioxidant activity, and mechanical properties of the resulting filaments. PETG expansion degree ranged from ~3 to 120%, with antioxidant loading ranging from 2.28 to 17.96 g per 100 g of polymer, corresponding to oxidation inhibition values of 7.65 and 66.55%, respectively. The temperature and the binary interaction between pressure and depressurization rate most affected these properties. The mechanical properties of PETG filaments depended greatly on process variables. Tensile strength values were similar or lower than the untreated filaments. Young's modulus and elongation at break values decreased below ~1000 MPa and ~10%, respectively, after the scCO2 treatment and impregnation. The extent of this decrease depended on the supercritical operational parameters. Therefore, filaments with higher antioxidant activity and different expansion degrees and mechanical properties were obtained by adjusting the supercritical processing conditions.

Green Processing of Neat Poly(lactic acid) Using Carbon Dioxide under Elevated Pressure for Preparation of Advanced Materials: A Review (2012-2022)

This review provides a concise overview of up-to-date developments in the processing of neat poly(lactic acid) (PLA), improvement in its properties, and preparation of advanced materials using a green medium (CO₂ under elevated pressure). Pressurized CO₂ in the dense and supercritical state is a superior alternative medium to organic solvents, as it is easily available, fully recyclable, has easily tunable properties, and can be completely removed from the final material without post-processing steps. This review summarizes the state of the art on PLA drying, impregnation, foaming, and particle generation by the employment of dense and supercritical CO₂ for the development of new materials. An analysis of the effect of processing methods on the final material properties was focused on neat PLA and PLA with an addition of natural bioactive components. It was demonstrated that CO₂-assisted processes enable the control of PLA properties, reduce operating times, and require less energy compared to conventional ones. The described environmentally friendly processing techniques and the versatility of PLA were employed for the preparation of foams, aerogels, scaffolds, microparticles, and nanoparticles, as well as bioactive materials. These PLA-based materials can find application in tissue engineering, drug delivery, active food packaging, compostable packaging, wastewater treatment, or thermal insulation, among others.

Effect of the Processing Conditions on the Supercritical Extraction and Impregnation of Rosemary Essential Oil in Linear Low-Density Polyethylene Films

The supercritical fluid extraction of essential oil from rosemary leaves and its subsequent impregnation in linear low-density polyethylene (LLDPE) films were studied. The effects of temperature (318 and 338 K), pressure (15 and 25 MPa) and rosemary particle size (0.9 and 0.15 mm) on the extraction yield were investigated. Impregnation assays were developed at two different values of pressure (12 and 20 MPa), temperature (308 and 328 K), and impregnation time (1 and 5 h). The extraction yield of rosemary essential oil was increased by increasing pressure and decreasing particle size and temperature. ANOVA results showed that temperature, pressure, and time significantly impacted the essential oil impregnation yield in LLDPE films. The maximum impregnation yield (1.87 wt. %) was obtained at 12 MPa, 328 K, and 5 h. The antioxidant activity and the physical-mechanical properties of impregnated films were analyzed. The IC50 values for all the impregnated LLDPE samples were close to the IC50 value of the extract showing that the impregnated films have a significant antioxidant activity.

Supercritical Fluid Extraction from Zataria multiflora Boiss and Impregnation of Bioactive Compounds in PLA for the Development of Materials with Antibacterial Properties

In this research, the extraction with supercritical carbon dioxide (SC-CO2) and the subsequent impregnation of the extracted bioactive compounds from Zataria multiflora Boiss (Z. multiflora) into polylactic acid (PLA) films was investigated. The effects of temperature (318 and 338 K), pressure (15 and 25 MPa) and cosolvent presence (0 and 3 mol%) on the extraction yield were studied. The SC-CO2 assisted impregnation runs were carried out in a discontinuous mode at different pressure (15 and 25 MPa), temperature (318 and 328 K), and time (2 and 8 h) values, using 0.5 MPa min−1 as a constant value of depressurization rate. ANOVA results confirmed that pressure, temperature, and time influenced the extraction yield. Moreover, antioxidant activities of extracts of Z. multiflora were evaluated using 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assays. In addition, the antibacterial activities of the extracts were screened against standard strains of Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). The results of this investigation indicated that extracts obtained from the aerial parts of Z. multiflora possessed antioxidant and antibacterial properties. The impregnated samples presented strong antibacterial activity against the selected microorganisms.

Supercritical Impregnation of Mango Leaf Extract into PLA 3D-Printed Devices and Evaluation of Their Biocompatibility with Endothelial Cell Cultures

The addition of natural substances with pharmacoactive properties to polymeric biomedical devices would provide beneficial regarding the assimilation of these endoprostheses when implanted into a patient’s body. The added drug would facilitate endothelization by regulating the inflammatory processes that such interventions entail, preventing contamination hazards and favoring the angiogenesis or formation of blood vessels in the tissue. The present work used mango leaf extract (MLE) obtained through pressurized ethanol for this purpose. Polylactic acid (PLA) in the form of filaments or 3D-printed disks was impregnated by means of supercritical technology with MLE for the culture essays. The release kinetics has been studied and the polymer matrices have been examined by scanning electron microscopy (SEM). The impregnated devices were subjected to in vitro culture of colony-forming endothelial cells. The influence of the different impregnation conditions used for the production of the MLE impregnated polymeric devices on the development of the cell culture was determined by fluorescence microscopy. The best results were obtained from the calcein cultures on 35 °C MLE impregnated into 3D-printed polymer disks.