Zinc reduces collagen degradation in demineralized human dentin explants

Filler Mixed Into Adhesives Does Not Necessarily Improve Their Mechanical Properties

OBJECTIVES

To investigate the influence of filler type/loading on the micro-tensile fracture strength (μTFS) of adhesive resins, as measured 'immediately' upon preparation and after 1-week water storage ('water-stored').

METHODS

The morphology and particle-size distribution of three filler particles, referred to as 'Glass-S' (Esschem Europe), 'BioUnion' (GC), and 'CPC_Mont', were correlatively characterized by SEM, TEM, and particle-size analysis. These filler particles were incorporated into an unfilled adhesive resin ('BZF-29unfilled', GC) in different concentrations to measure the 'immediate' μTFS. After 1-week water storage, the 'water-stored' μTFS of the experimental particle-filled adhesive resins with the most optimum filler loading, specific for each filler type, was measured. In addition, the immediate and water-stored μTFS of the adhesive resins of three experimental two-step universal adhesives based on the same resin matrix but varying for filler type/loading, coded as 'BZF-21' (containing silica and bioglass), 'BZF-29' (containing solely silica), and 'BZF-29_hv' (highly viscous with a higher silica loading than BZF-29), and of the adhesive resins of the gold-standard adhesives OptiBond FL ('Opti-FL', Kerr) and Clearfil SE Bond 2 ('C-SE2', Kuraray Noritake) was measured along with that of BZF-29unfilled (GC) serving as control/reference. Statistics involved one-way and two-way ANOVA followed by post-hoc multiple comparisons (α<0.05).

RESULTS

Glass-S, BioUnion, and CPC_Mont represent irregular fillers with an average particle size of 8.5-9.9 μm. Adding filler to BZF-29unfilled decreased μTFS regardless of filler type/loading. One-week water storage reduced μTFS of all adhesive resins except BZF-21, with the largest reduction in μTFS recorded for BZF-29unfilled. Among the three filler types, the μTFS of the 30 wt% Glass-S and 20 wt% BioUnion filled adhesive resin was not significantly different from the μTFS of BZF-29unfilled upon water storage.

CONCLUSIONS

Adding filler particles into adhesive resin did not enhance its micro-tensile fracture strength but appeared to render it less sensitive to water storage as compared to the unfilled adhesive resin investigated.

Development of a zinc chloride-based chemo-mechanical system for potential minimally invasive dental caries removal system

Background/purpose

The chemo-mechanical caries-removal technique is known to offer advantages of selective dentin caries treatment while leaving healthy dental tissues intact. However, current sodium hypochlorite based reagents usually excessively damage dentin collagen. Therefore, the purpose of this study was to develop a novel chemo-mechanical caries-removal system to preserve the collagen network for subsequent prosthetic restorations.

Materials and methods

The calfskin-derived collagen was chosen as a model system to investigate the dissolution behavior of collagen under different operating conditions of chemical-ultrasonic treatment systems. The molecular weight, triple-helix structure, the morphology, and functional group of collagen after treatment were investigated.

Results

Various concentrations of sodium hypochlorite or zinc chloride together with ultrasonic machinery were chosen to investigate. The outcomes of circular dichroism (CD) spectra demonstrated stability of the triple-helix structure after treatment of a zinc chloride solution. In addition, two apparent bands at molecular weights (MWs) of 130 and 121 kDa evidenced the stability of collagen network. The positive 222 nm and 195 nm negative CD absorption band indicated the existence of a triple-helix structure for type I collagen. The preservation of the morphology and functional group of the collagen network on the etched dentin surface were investigated by in vitro dentin decalcification model.

Conclusion

Unlike NaOCl, the 5 wt% zinc chloride solution combined with ultra-sonication showed dissolution rather than denature as well as degradation of the dentin collagen network. Additional in vivo evaluations are needed to verify its usefulness in clinical applications.

High-Performance Bioinspired Microspheres for Boosting Dental Adhesion

Dental adhesives are widely used in daily practice for minimally invasive restorative dentistry but suffer from bond degradation and biofilm attack. Bio-inspired by marine mussels having excellent surface-adhesion capability and high chemical affinity of polydopamine (PDA) to metal ions, herein, experimental zinc (Zn)-containing polydopamine-based adhesive formulation, further being referred to as "Zn-PDA@SiO2 "-incorporated adhesive is proposed as a novel dental adhesive. Different Zn contents (5 and 10 mm) of Zn-PDA@SiO2 are prepared. Considering the synergistic effect of Zn and PDA, Zn-PDA@SiO2 not only presents excellent antibacterial potential and notably inhibits enzymatic activity (soluble and matrix-bound proteases), but also exhibits superior biocompatibility and biosafety in vitro/vivo. The long-term bond stability is substantially improved by adding 5 wt% 5 mm Zn-PDA@SiO2 to the primer. The aged bond strength of the experimentally formulated dental adhesives applied in self-etch (SE) bonding mode is 1.9 times higher than that of the SE gold-standard adhesive. Molecular dynamics calculations indicate the stable formation of covalent bonds, Zn-assisted coordinative bonds, and hydrogen bonds between PDA and collagen. Overall, this bioinspired dental adhesive provides an avenue technology for innovative biomedical applications and has already revealed promising perspectives for dental restorative dentistry.

Doped Electrospinned Material-Guides High Efficiency Regional Bone Regeneration

The main target of bone tissue engineering is to design biomaterials that support bone regeneration and vascularization. Nanostructured membranes of (MMA)1-co-(HEMA)1/(MA)3-co-(HEA)2 loaded with 5% wt of SiO2-nanoparticles (Si-M) were doped with zinc (Zn-Si-M) or doxycycline (Dox-Si-M). Critical bone defects were effectuated on six New Zealand-bred rabbit skulls and then they were covered with the membranes. After six weeks, a histological analysis (toluidine blue technique) was employed to determine bone cell population as osteoblasts, osteoclasts, osteocytes, M1 and M2 macrophages and vasculature. Membranes covering the bone defect determined a higher count of bone cells and blood vessels than in the sham group at the top regions of the defect. Pro-inflammatory M1 appeared in a higher number in the top regions than in the bottom regions, when Si-M and Dox-Si-M were used. Samples treated with Dox-Si-M showed a higher amount of anti-inflammatory and pro-regenerative M2 macrophages. The M1/M2 ratio obtained its lowest value in the absence of membranes. On the top regions, osteoblasts were more abundant when using Si-M and Zn-Si-M. Osteoclasts were equally distributed at the central and lateral regions. The sham group and samples treated with Zn-Si-M attained a higher number of osteocytes at the top regions. A preferential osteoconductive, osteoinductive and angiogenic clinical environment was created in the vicinity of the membrane placed on critical bone defects.

Dexamethasone-doped nanoparticles improve mineralization, crystallinity and collagen structure of human dentin

OBJECTIVES

Bioactive materials have been used for functionalization of adhesives to promote dentin remineralization. This study aims to evaluate bonding ability and both mechanical and chemical behavior of demineralized dentin infiltrated with polymeric nanoparticles doped with dexamethasone (Dex-NPs).

METHODS

Dentin conditioned surfaces were infiltrated with NPs, Dex-NPs or Dex-Zn-NPs. Bonded interfaces were also created and stored for 24 h or 21d, and then submitted to microtensile bond strength testing. Dentin remineralization was analyzed by Nanohardness, Young's modulus and Raman analysis.

RESULTS

At 21d of storage, dentin treated with undoped-NPs attained the lowest nanohardness and Young's modulus. Dex-NPs and Zn-Dex-NPs increased dentin nanohardness and Young's modulus after 21d Raman analysis showed high remineralization, crystallinity, crosslinking and better structure of collagen when functionalized Dex-NPs were present at the dentin interface.

CONCLUSIONS

Infiltration of dentin with Dex-NPs promoted functional remineralization as proved by nanomechanical and morpho-chemical evaluation tests. Dexamethasone in dentin facilitated crystallographic maturity, crystallinity and improved maturity and secondary structure of dentin collagen.

CLINICAL SIGNIFICANCE

Using dexamethasone-functionalized NPs before resin infiltration is a clear option to obtain dentin remineralization, as these NPs produce the reinforcement of the dentin structure, which will lead to the improvement of the longevity of resin restorations.

Insight into the development of versatile dentin bonding agents to increase the durability of the bonding interface

Despite the huge improvements made in adhesive technology over the past 50 years, there are still some unresolved issues regarding the durability of the adhesive interface. A complete sealing of the interface between the resin and the dentin substrate remains difficult to achieve, and it is doubtful whether an optimal interdiffusion of the adhesive system within the demineralized collagen framework can be produced in a complete and homogeneous way. In fact, it is suggested that hydrolytic degradation, combined with the action of dentin matrix enzymes, destabilizes the tooth-adhesive bond and disrupts the unprotected collagen fibrils. While a sufficient resin–dentin adhesion is usually achieved immediately, bonding efficiency declines over time. Thus, here, a review will be carried out through a bibliographic survey of scientific articles published in the last few years to present strategies that have been proposed to improve and/or develop new adhesive systems that can help prevent degradation at the adhesive interface. It will specially focus on new clinical techniques or new materials with characteristics that contribute to increasing the durability of adhesive restorations and avoiding the recurrent replacement restorative cycle and the consequent increase in damage to the tooth.

Effects of zinc deficiency on the regeneration of olfactory epithelium in mice

The olfactory epithelium can regenerate after damage; however, the regeneration process is affected by various factors, such as viral infections, head trauma, and medications. Zinc is an essential trace element that has important roles in organ development, growth, and maturation. Zinc also helps regulate neurotransmission in the brain; nevertheless, its relationship with olfactory epithelium regeneration remains unclear. Therefore, we used a severe zinc deficiency mouse model to investigate the effects of zinc deficiency on olfactory epithelium regeneration. Male wild-type C57BL/6 mice were divided into zinc-deficient and control diet groups at the age of 4 weeks, and methimazole was administered at the age of 8 weeks to induce severe olfactory epithelium damage. We evaluated the olfactory epithelium before and 7, 14, and 28 days after methimazole administration by histologically analyzing paraffin sections. RNA sequencing was also performed at the age of 8 weeks before methimazole administration to examine changes in gene expression caused by zinc deficiency. In the zinc-deficient group, the regenerated olfactory epithelium thickness was decreased at all time points, and the numbers of Ki-67-positive, GAP43-positive, and olfactory marker protein-positive cells (i.e. proliferating cells, immature olfactory neurons, and mature olfactory neurons, respectively) failed to increase at some time points. Additionally, RNA sequencing revealed several changes in gene expression, such as a decrease in the expression of extracellular matrix-related genes and an increase in that of inflammatory response-related genes, in the zinc-deficient group. Therefore, zinc deficiency delays olfactory epithelium regeneration after damage in mice.

Barrier Membranes for Guided Bone Regeneration (GBR): A Focus on Recent Advances in Collagen Membranes

Guided bone regeneration (GBR) has become a clinically standard modality for the treatment of localized jawbone defects. Barrier membranes play an important role in this process by preventing soft tissue invasion outgoing from the mucosa and creating an underlying space to support bone growth. Different membrane types provide different biological mechanisms due to their different origins, preparation methods and structures. Among them, collagen membranes have attracted great interest due to their excellent biological properties and desired bone regeneration results to non-absorbable membranes even without a second surgery for removal. This work provides a comparative summary of common barrier membranes used in GBR, focusing on recent advances in collagen membranes and their biological mechanisms. In conclusion, the review article highlights the biological and regenerative properties of currently available barrier membranes with a particular focus on bioresorbable collagen-based materials. In addition, the advantages and disadvantages of these biomaterials are highlighted, and possible improvements for future material developments are summarized.

Degradation and Stabilization of Resin-Dentine Interfaces in Polymeric Dental Adhesives: An Updated Review

Instability of the dentine-resin interface is owed to the partial/incomplete penetration of the resin adhesives in the collagen fibrils. However, interfacial hydrolysis of the resin-matrix hybrid layer complex activates the collagenolytic and esterase enzymes that cause the degradation of the hybrid layer. Adequate hybridization is often prevented due to the water trapped between the interfibrillar spaces of the collagen network. Cyclic fatigue rupture and denaturation of the exposed collagen fibrils have been observed on repeated application of masticatory forces. To prevent interfacial microstructure, various approaches have been explored. Techniques that stabilize the resin–dentine bond have utilized endogenous proteases inhibitors, cross linking agents’ incorporation in the exposed collagen fibrils, an adhesive system free of water, and methods to increase the monomer penetration into the adhesives interface. Therefore, it is important to discover and analyze the causes of interfacial degradation and discover methods to stabilize the hybrid layer to execute new technique and materials. To achieve a predictable and durable adhesive resin, restoration is a solution to the many clinical problems arising due to microleakage, loss of integrity of the restoration, secondary caries, and postoperative sensitivity. To enhance the longevity of the resin-dentine bond strength, several experimental strategies have been carried out to improve the resistance to enzymatic degradation by inhibiting intrinsic collagenolytic activity. In addition, biomimetic remineralization research has advanced considerably to contemporary approaches of both intrafibrillar and extrafibrillar remineralization of dental hard tissues. Thus, in the presence of biomimetic analog complete remineralization of collagen, fibers are identified.

Inhibitory activity of S-PRG filler on collagen-bound MMPs and dentin matrix degradation

OBJECTIVES

To evaluate the inhibitory activity of an ion-releasing filler (S-PRG) eluate on dentin collagen-bound metalloproteinases (MMPs) and dentin matrix degradation.

METHODS

Dentin beams (5 × 2 × 0.5 mm) from human molars were completely demineralized to produce dentin matrix specimens. The dry mass was measured, and a colorimetric assay (Sensolyte) determined the initial total MMP activity to allocate the beams into four treatment groups (n = 10/group): 1) water for 1 min (negative control); 2) 2% chlorhexidine digluconate (CHX - inhibitor control) for 1 min; 3) S-PRG eluate for 1 min; 4) S-PRG eluate for 30 min. After the treatments, the total MMP activity was reassessed. The specimens were stored in simulated body fluid (SBF) at 37 °C for up to 21 days. The dry mass was reassessed weekly. On day 7, the dentin matrix degradation was analyzed for the presence of collagen fragments (CF; Sirius Red) and hydroxyproline (Hyp) in the SBF. Statistical analyses were performed with ANOVA/Tukey, paired t-tests, and RM-ANOVA/Sidak (α = 5%).

RESULTS

S-PRG eluate exposure for 1 and 30 min reduced (p < 0.0001) MMP activity. S-PRG exposure for 30 min presented MMP activity inhibition equivalent to CHX (p = 0.061). S-PRG and CHX decreased CF (p ≤ 0.007) and Hyp (p < 0.046) release. After 21 days of storage, S-PRG-treated beams, regardless of exposure time, presented a reduced (p ≤ 0.017) mass loss, intermediate between CHX and control.

CONCLUSION

Treating demineralized dentin with S-PRG eluate for 1 or 30 min reduced matrix-bound MMP activity and dentin matrix degradation for up to 21 days.

CLINICAL SIGNIFICANCE

S-PRG filler may hinder the progression of dentin carious/erosive lesions and enhance the stabilization of dentin bonding interfaces.

Optimizing the bio-degradability and biocompatibility of a biogenic collagen membrane through cross-linking and zinc-doped hydroxyapatite

Biogenic collagen membranes have been widely used as soft tissue barriers in guided bone regeneration (GBR) and guided tissue regeneration (GTR). Nevertheless, their clinical performance remains unsatisfactory because of their low mechanical strength and fast degradation rate in vivo. Although cross-linking with chemical agents is effective and reliable for prolonging the degradation time of collagen membranes, some adverse effects including potential cytotoxicity and undesirable tissue integration have been observed during this process. As a fundamental nutritional trace element, zinc plays an active role in promoting the growth of cells and regulating the degradation of the collagen matrix. Herein, a biogenic collagen membrane was cross-linked with glutaraldehyde-alendronate to prolong its degradation time. The physiochemical and biological properties were enhanced by the incorporation of zinc-doped nanohydroxyapatite (nZnHA), with the native structure of collagen preserved. Specifically, the cross-linking combined with the incorporation of 1% and 2% nZnHA seemed to endow the membrane with the most appropriate biocompatibility and tissue integration capability among the cross-linked membranes, as well as offering a degradation period of six weeks in a rat subcutaneous model. Thus, improving the clinical performance of biogenic collagen membranes by cross-linking together with the incorporation of nZnHA is a promising strategy for the improvement of biogenic collagen membranes. STATEMENT OF SIGNIFICANCE: The significance of this research includes.

Enhancing the Stability of the Resin-Dentin Bonding Interface with Ag+- and Zn2+-Exchanged Zeolite A

Enhancing the stability of the resin-dentin bonding interface via simultaneously improving the antibacterial, mechanical, and adhesive properties of a dental adhesive is the key to prolonging the longevity of dental restoration for caries treatment. Herein, we present the stabilization effect of Ag⁺- and Zn²⁺-exchanged zeolite A (denoted as Ag-A and Zn-A, respectively) on the resin-dentin bonding interface. Ag-A and Zn-A zeolites exhibited sustained ion release capability, outstanding biocompatibility to L929 cells (<2 mg/mL), and excellent antibacterial ability to Streptococcus mutans (minimum inhibitory concentration: 100 μg/mL for Ag-A and 200 μg/mL for Zn-A). One-step self-etching adhesives modified by Ag-A, Zn-A, or Ag-/Zn-A (1/1 in weight) zeolites with an ultralow loading of 0.2 wt % exhibited favorable antibacterial activity with the inhibition of biofilm formation by 70.33, 56.47, and 62.54%, respectively. Compared to the control group, Zn-A- and Ag-/Zn-A-modified adhesives significantly increased the wettability properties of the adhesive and the long-term resin-dentin bond strength (by ∼25%) after 5000 thermocycles of aging. The current data demonstrated that the introduction of 0.2 wt % Zn-A or Ag-/Zn-A into the adhesive remarkably enhanced the stability of the resin-dentin bonding interface. Our findings provide a new strategy to modify the dental adhesive for further optimizing the longevity of dental restorations for caries.

Potential of Fluoride-Containing Zinc Oxide and Copper Oxide Nanocomposites on Dentin Bonding Ability

Despite recent advances in bonding restorations, which are the basis of restorative dentistry, secondary caries are still able to form. Previously, a novel fluoride-containing zinc and copper (ZCF) nanocomposite was introduced to prevent the formation of caries due to its antibacterial activity. In this study, we studied the impact of ZCF nanoparticles on the adhesive strength of bonding restorations through micro-tensile bond strength (µTBS) testing. The impact of antibacterial and matrix metalloproteinase (MMP) inhibitors on the nanoparticles was also examined. The nanocomposites were prepared using a simple one-step homogeneous co-precipitation method at a low temperature. A self-etch adhesive was applied to 10 extracted caries-free human molars with (test group) and without (control group) the ZCF nanoparticles. This was followed by composite resin build-up and µTBS testing, MMP activity assays, and evaluation of the antibacterial effects. The results showed no significant differences in the µTBS between the ZCF and the control groups. However, the ZCF exhibited a significant inhibitory effect against MMP-2, MMP-8, and MMP-9, in addition to an antibacterial effect on Streptococcus mutans. Therefore, the present study demonstrated that the addition of ZCF nanoparticles to adhesive systems can result in MMP inhibition and antibacterial action while maintaining the mechanical properties of the bonding restorations.

Treatment of Wound Infections in a Mouse Model Using Zn2+-Releasing Phage Bound to Gold Nanorods

Infections caused by drug-resistant bacteria, particularly Gram-negative organisms, are increasingly difficult to treat using antibiotics. A potential alternative is "phage therapy", in which phages infect and lyse the bacterial host. However, phage therapy poses serious drawbacks and safety concerns, such as the risk of genetic transduction of antibiotic resistance genes, inconsistent pharmacokinetics, and unknown evolutionary potential. In contrast, metallic nanoparticles possess precise, tunable properties, including efficient conversion of electronic excitation into heat. In this work, we demonstrate that engineered phage-nanomaterial conjugates that target the Gram-negative pathogen Pseudomonas aeruginosa are highly effective as a treatment of infected wounds in mice. Photothermal heating, performed as a single treatment (15 min) or as two treatments on consecutive days, rapidly reduced the bacterial load and released Zn²⁺ to promote wound healing. The phage-nanomaterial treatment was significantly more effective than systemic standard-of-care antibiotics, with a >10× greater reduction in bacterial load and ∼3× faster healing as measured by wound size reduction when compared to fluoroquinolone treatment. Notably, the phage-nanomaterial was also effective against a P. aeruginosa strain resistant to polymyxins, a last-line antibiotic therapy. Unlike these antibiotics, the phage-nanomaterial showed no detectable toxicity or systemic effects in mice, consistent with the short duration and localized nature of phage-nanomaterial treatment. Our results demonstrate that phage therapy controlled by inorganic nanomaterials can be a safe and effective antimicrobial strategy in vivo.

Zn-containing Adhesives Facilitate Collagen Protection and Remineralization at the Resin-Dentin Interface: A Narrative Review

This is a narrative review of the literature assessing the potential effectiveness of doping dentin polymeric adhesives with zinc compounds in order to improve bonding efficacy, remineralization and protection against degradation. A literature search was conducted using electronic databases, such as PubMed, MEDLINE, DIMDI and Web of Science. Through our search, we found literature demonstrating that Zn-doped dentin adhesives promote protection and remineralization of the resin-dentin interfaces. The increased bioactivity has also facilitated dentinal tubules' occlusion by crystals' precipitation contributing to improved sealing efficacy of restorations. Loading dentin adhesives with zinc gives rise to an increase of both crystallinity of mineral and crosslinking of collagen. The main role of zinc, in dentin adhesives, is to inhibit collagen proteolysis. We concluded that zinc exerts a protective effect through binding at the collagen-sensitive cleavage sites of matrix-metalloproteinases (MMPs), contributing to dentin matrix stabilization. Zinc may not only act as a MMPs inhibitor, but also influence signaling pathways and stimulate metabolic effects in dentin mineralization and remineralization processes. Zn-doped adhesives increase the longevity of dentin bonding through MMPs inhibition. Zn poses a remineralization strategy in demineralized dentin.

Captopril inhibits matrix metalloproteinase activity and improves dentin bonding durability

OBJECTIVES

We investigated the inhibitory effects of captopril on matrix metalloproteinases (MMPs) and its effect as a primer on dentin bonding durability.

MATERIALS AND METHODS

One hundred fifty human third molars were selected. Flat surfaces of the middle dentin were exposed, etched 15 s, and followed by pretreatment with a primer for 60 s, including distilled water (control, the negative control primer), 2% chlorhexidine digluconate (CHD, the positive control primer), and captopril solution. Inhibitory effects of primers on MMPs were evaluated by hydroxyproline and gelatinase activity tests. All primers were applied on dentin followed by bonding. Some of the samples were sliced into slabs, placed in a fluorescent solution containing gelatin, and incubated for in situ zymography. Some were cut into sticks, and after aging for 1 day, 12 months, or 24 months, microtensile bonding strength was tested. Some were cut into slabs, aged for 1 day, 12 months, or 24 months, and taken out for nanoleakage tests to reveal interface defects.

RESULTS

Hydroxyproline and gelatinase activity analyses showed that captopril exerted better inhibitory effects on MMPs, relative to 2% CHD (p < 0.05). A 0.2% captopril aqueous solution (0.2% CapW) was chosen to apply to the dentin. In situ zymography showed that inhibitory effects of captopril on gelatinase were significantly higher compared to 2% CHD (p < 0.01). Microtensile strength revealed that the bonding effects of the 0.2% CapW group lasted longer, compared to the control and 2% CHD groups (p < 0.05). Interface defects, detected by nanoleakage, were significantly reduced in the 0.2% CapW group, compared to the control and 2% CHD groups (p < 0.05).

CONCLUSIONS

Captopril inhibits dentin MMP activities and effectively improves dentin bonding durability.

CLINICAL RELEVANCE

Captopril is a promising dentin bonding primer for improving bonding durability.

Biomimetic Gradient Scaffolds Containing Hyaluronic Acid and Sr/Zn Folates for Osteochondral Tissue Engineering

Regenerative therapies based on tissue engineering are becoming the most promising alternative for the treatment of osteoarthritis and rheumatoid arthritis. However, regeneration of full-thickness articular osteochondral defects that reproduces the complexity of native cartilage and osteochondral interface still remains challenging. Hence, in this work, we present the fabrication, physic-chemical characterization, and in vitro and in vivo evaluation of biomimetic hierarchical scaffolds that mimic both the spatial organization and composition of cartilage and the osteochondral interface. The scaffold is composed of a composite porous support obtained by cryopolymerization of poly(ethylene glycol) dimethacrylate (PEGDMA) in the presence of biodegradable poly(D,L-lactide-co-glycolide) (PLGA), bioactive tricalcium phosphate β-TCP and the bone promoting strontium folate (SrFO), with a gradient biomimetic photo-polymerized methacrylated hyaluronic acid (HAMA) based hydrogel containing the bioactive zinc folic acid derivative (ZnFO). Microscopical analysis of hierarchical scaffolds showed an open interconnected porous open microstructure and the in vitro behaviour results indicated high swelling capacity with a sustained degradation rate. In vitro release studies during 3 weeks indicated the sustained leaching of bioactive compounds, i.e., Sr2+, Zn2+ and folic acid, within a biologically active range without negative effects on human osteoblast cells (hOBs) and human articular cartilage cells (hACs) cultures. In vitro co-cultures of hOBs and hACs revealed guided cell colonization and proliferation according to the matrix microstructure and composition. In vivo rabbit-condyle experiments in a critical-sized defect model showed the ability of the biomimetic scaffold to promote the regeneration of cartilage-like tissue over the scaffold and neoformation of osteochondral tissue.

Effect of zinc oxide nanoparticles on physical and antimicrobial properties of resin-modified glass ionomer cement

Background:

To improve the limitations, many modifications in the resin-modified glass ionomer (RMGI) composition have been proposed. In this study, we evaluated the effect of different concentrations of zinc oxide (ZnO) nanoparticles incorporated into RMGI cement on its physical and antimicrobial properties.

Materials and Methods:

In this in vitro study, ZnO nanoparticles with 0–4 wt.% concentrations were incorporated into RMGI. The following tests were carried out: (a) Antibacterial activity against Streptococcus mutans tested by disc diffusion method, (b) mechanical behavior assessment by measuring flexural strength (FS) and flexural modulus (FM), (c) micro-shear bond strength (μ-SBS), and (d) fluoride and zinc release. Data were analyzed using the statistical tests of ANOVA, t-test, and Tukey's HSD post hoc in SPSS V22. The level of significancy was 0.05.

Results:

In the disc diffusion method, specimens with 2 wt.% ZnO nanoparticles showed the highest antimicrobial efficacy (P < 0.05). After 1 month of water storage, no significant difference was observed in FS and FM of the samples (P > 0.05). In 2 wt.% ZnO nanoparticles group, μSBS increased in the first 7 days but decreased by 17% after one month, which showed a significant difference with that of the control group. The fluoride release did no change in the ZnO nanoparticle-containing group compared with the control group at all time intervals.

Conclusion:

Incorporation of 2 wt.% ZnO nanoparticles into the RMGI cement adds antimicrobial activity to the cement without sacrificing FS and fluoride release properties, while decreased μSBS.

Synergistic Effect of Bioactive Inorganic Fillers in Enhancing Properties of Dentin Adhesives-A Review

Dentin adhesives (DAs) play a critical role in the clinical success of dental resin composite (DRC) restorations. A strong bond between the adhesive and dentin improves the longevity of the restoration, but it is strongly dependent on the various properties of DAs. The current review was aimed at summarizing the information present in the literature regarding the improvement of the properties of DAs noticed after the addition of bioactive inorganic fillers. From our search, we were able to find evidence of multiple bioactive inorganic fillers (bioactive glass, hydroxyapatite, amorphous calcium phosphate, graphene oxide, calcium chloride, zinc chloride, silica, and niobium pentoxide) in the literature that have been used to improve the different properties of DAs. These improvements can be seen in the form of improved hardness, higher modulus of elasticity, enhanced bond, flexural, and ultimate tensile strength, improved fracture toughness, reduced nanoleakage, remineralization of the adhesive-dentin interface, improved resin tag formation, greater radiopacity, antibacterial effect, and improved DC (observed for some fillers). Most of the studies dealing with the subject area are in vitro. Future in situ and in vivo studies are recommended to positively attest to the results of laboratory findings.

Melatonin-doped polymeric nanoparticles reinforce and remineralize radicular dentin: Morpho-histological, chemical and biomechanical studies

OBJECTIVES

To investigate the effectiveness of novel polymeric nanoparticles (NPs) doped with melatonin (ML) in reducing dentin permeability and facilitating dentin remineralization after endodontic treatment.

METHODS

The effect of undoped NPs and ML-doped NPs (ML-NPs) was tested in radicular dentin, at 24 h and 6 m. A control group without NPs was included. ML liberation was measured. Radicular dentin was assessed for fluid filtration. Dentin remineralization was analyzed by scanning electron microscopy, AFM, Young's modulus (Ei), Nano DMA-tan delta, and Raman analysis.

RESULTS

ML release ranged from 1.85 mg/mL at 24 h to 0.033 mg/mL at 28 d. Both undoped NPs and ML-NPs treated dentin exhibited the lowest microleakage, but samples treated with ML-NPs exhibited hermetically sealed dentinal tubules and extended mineral deposits onto dentin. ML-NPs promoted higher and durable Ei, and functional remineralization at root dentin, generating differences between the values of tan delta among groups and creating zones of stress concentration. Undoped-NPs produced closure of some tubules and porosities at the expense of a relative mineral amorphization. Chemical remineralization based on mineral and organic assessments was higher in samples treated with ML-NPs. When using undoped NPs, precipitation of minerals occurred; however, radicular dentin was not mechanically reinforced but weakened over time.

SIGNIFICANCE

Application of ML-NPs in endodontically treated teeth, previous to the canal filling step, is encouraged due to occlusion of dentinal tubules and the reinforcement of the radicular dentin structure.

Review of nano-technology applications in resin-based restorative materials

OBJECTIVE

Nanotechnology has progressed significantly and particles as small as 3 nm are being employed in resin-based restorative materials to improve clinical performance. The goal of this review is to report the progress of nanotechnology in Restorative Dentistry by reviewing the advantages, limitations, and applications of resin-based restorative materials with nanoparticles.

MATERIALS AND METHODS

A literature review was conducted using PubMed/Medline, Scopus and Embase databases. In vitro, in vivo and in situ research studies published in English between 1999 and 2020, and which focused on the analysis of resin-based restorative materials containing nanoparticles were included.

RESULTS

A total of 140 studies were included in this review. Studies reported the effect of incorporating different types of nanoparticles on adhesive systems or resin composites. Mechanical, physical, and anti-bacterial properties were described. The clinical performance of resin-based restorative materials with nanoparticles was also reported.

CONCLUSIONS

The high surface area of nanoparticles exponentially increases the bioactivity of materials using bioactive nanofillers. However, the tendency of nanoparticles to agglomerate, the chemical instability of the developed materials and the decline of rheological properties when high ratios of nanoparticles are employed are some of the obstacles to overcome in the near future.

CLINICAL SIGNIFICANCE

In spite of the recent advancements of nanotechnology in resin-based restorative materials, some challenges need to be overcome before new nano-based restorative materials are considered permanent solutions to clinical problems.

Effect of aspartic acid on the crystallization kinetics of ACP and dentin remineralization

Type I collagen and non-collagen proteins are the main organic components of dentin. This study aimed to investigate the biomimetic remineralization of demineralized dentin by aspartic acid (Asp), which is abundant in non-collagenous proteins (NCPs). Asp was added to a mineralizing solution containing polyacrylic acid (PAA) to explore the mechanism of Asp regulating the pure amorphous calcium phosphate (ACP) phase transition process. The remineralization process and superstructure of the remineralized layer of demineralized dentin were evaluated and analyzed by transmission electron microscope (TEM) and scanning electron microscope (SEM), and the biological stability of the remineralized layer was investigated by collagenase degradation experiment. It demonstrated that Asp promoted the crystallization kinetics of PAA-stabilized amorphous calcium phosphate to hydroxyapatite (HAP), and shortened the remineralization time of demineralized dentin from 7 days to 2 days. The newly formed remineralized dentin had similar morphology and biological stability to the natural dentin layer. The presence of a large number of Asp residues in NCPs promoted the phase transformation of ACP, and further revealed the mechanism of action of NCPs in dentin biomineralization. This experiment also showed that Asp promoted the biomimetic remineralization of dentin; the morphology and hierarchical structure of remineralized layer was similar to that of natural teeth, and had good biological properties.

Remineralising effects of fluoride varnishes containing calcium phosphate on artificial root caries lesions with adjunctive application of proanthocyanidin

OBJECTIVES

To evaluate the remineralising effects of fluoride (F) varnishes containing bioavailable calcium-phosphate compound (Ca-P) based remineralisation systems and 5000 ppm F toothpaste (FTP) on root caries lesions (RCLs) and the potential effects of proanthocyanidin (PA) for the treatments of RCLs when used as an adjunct to F regimens.

METHODS

Demineralised root dentine and a pH-cycling model were used to mimic RCLs and the oral environment. Remineralising effects of MI Varnish^TM (MIV) containing casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and Clinpro™ White Varnish (CPWV) containing tri-calcium phosphate (TCP) along with FTP and PA were evaluated regarding the birefringence, elemental composition, mechanical properties and mineral density of remineralised dentine with Duraphat^TM as a comparison.

RESULTS

MIV, CPWV and Duraphat^TM promoted the incorporation of F into RCLs and increased mineral density but did not change microhardness of root dentine significantly. Surface microhardness increased significantly when MIV or CPWV was used with 5000 ppm FTP. Application of PA with F regimens significantly increased subsurface mineral density. When PA was applied with MIV or CPWV along with FTP, the highest ion uptake and relative mineral gain (%ΔZ) was achieved, and significant increase of microhardness was up to 30 μm depth. Generally, MIV was associated with a higher mineral content gain than CPWV.

SIGNIFICANCE

Treatment of carious root surfaces remains challenging due to the complex pathological processes and difficulty in restoring the highly organised structure of root dentine. Treatment strategies targeting both remineralisation and preservation of the dentinal organic matrix have the potential to improve the fluoride-mediated remineralisation approaches.

Zn-doping of silicate and hydroxyapatite-based cements: Dentin mechanobiology and bioactivity

The objective was to state zinc contribution in the effectiveness of novel zinc-doped dentin cements to achieve dentin remineralization, throughout a literature or narrative exploratory review. Literature search was conducted using electronic databases, such as PubMed, MEDLINE, DIMDI, Embase, Scopus and Web of Science. Both zinc-doping silicate and hydroxyapatite-based cements provoked an increase of both bioactivity and intrafibrillar mineralization of dentin. Zinc-doped hydroxyapatite-based cements (oxipatite) also induced an increase in values of dentin nano-hardness, Young's modulus and dentin resistance to deformation. From Raman analyses, it was stated higher intensity of phosphate peaks and crystallinity as markers of dentin calcification, in the presence of zinc. Zinc-based salt formations produced low microleakage and permeability values with hermetically sealed tubules at radicular dentin. Dentin treated with oxipatite attained preferred crystal grain orientation with polycrystalline lattices. Thereby, oxipatite mechanically reinforced dentin structure, by remineralization. Dentin treated with oxipatite produced immature crystallites formations, accounting for high hydroxyapatite solubility, instability and enhanced remineralizing activity.

Evaluation of antibacterial and cytocompatible properties of multiple-ion releasing zinc-fluoride glass nanoparticles

Zinc-fluoride glass nanoparticles (Zinc-F) release several ions, such as fluoride, zinc and calcium ions, through acid-base reactions. The aim of this study was to evaluate the antibacterial and cytotoxic properties of Zinc-F. Antibacterial tests showed that a Zinc-F eluting solution significantly reduced the turbidity and colony-forming units of Streptococcus mutans and Actinomyces naeslundii, compared to that of calcium-fluoroaluminosilicate glass nanoparticles without zinc ions. In live/dead staining, Zinc-F eluate significantly decreased green-stained bacterial cells, indicating live cells, compared with the control (no application). Human dentin coated with Zinc-F showed suppressed S. mutans and A. naeslundii biofilm formation. Additionally, Zinc-F eluate showed low cytotoxic effects in osteoblastic and fibroblastic cells. Therefore, our findings suggested that Zinc-F exhibits antibacterial and biocompatible properties through multiple-ion release.

Effects of Zn-Doped Mesoporous Bioactive Glass Nanoparticles in Etch-and-Rinse Adhesive on the Microtensile Bond Strength

The purpose of this study was to assess the effects in the dentin bond strength of dental adhesives (DAs) and biological effects using zinc (Zn)-doped mesoporous bioactive glass nanoparticles (MBN-Zn). Synthesized MBN and MBN-Zn were characterized by scanning electron microscopy (SEM), X-ray diffraction and the Brunauer, Emmett and Teller (BET) method. The matrix metalloproteinases (MMP) inhibition effects of DA-MBN and DA-MBN-Zn were analyzed. The microtensile bond strength (MTBS) test was conducted before and after thermocycling to investigate the effects of MBN and MBN-Zn on the MTBS of DAs. The biological properties of DA-MBN and DA-MBN-Zn were analyzed with human dental pulp stem cells (hDPSCs). Compared with the DA, only the DA-1.0% MBN and DA-1.0% MBN-Zn exhibited a statistically significant decrease in MMP activity. The MTBS values after thermocycling were significantly increased in DA-1.0% MBN and DA-1.0% MBN-Zn compared with the DA (p < 0.05). It was confirmed via the MTT assay that there was no cytotoxicity for hDPSCs at 50% extract. In addition, significant increases in the alkaline phosphatase activity and Alizarin Red S staining were observed only in DA-1.0%MBN-Zn. These data suggest the 1.0% MBN and 1.0% MBN-Zn enhance the remineralization capability of DAs and stabilize the long-term MTBS of DAs by inhibiting MMPs.

Zinc-based particle with ionic liquid as a hybrid filler for dental adhesive resin

OBJECTIVES

The aim of this study was to evaluate the effect of a zinc-based particle with ionic liquid as filler for an experimental adhesive resin.

METHODS

The ionic liquid 1-n-butyl-3-methylimidazolium chloride (BMI.Cl) and zinc chloride (ZnCl₂) were used to synthesize 1-n-butyl-3-methylimidazolium trichlorozincate (BMI.ZnCl₃), which was hydrolyzed under basic conditions to produce the simonkolleite (SKT) particles. SKT was analyzed by scanning electron microscopy and transmission electron microscopy. An experimental adhesive resin was formulated and SKT was incorporated at 1, 2.5, or 5 wt.% in the adhesive. One group without SKT was a control group. The antibacterial activity against Streptococcus mutans, cytotoxicity, degree of conversion (DC), ultimate tensile strength (UTS), softening in solvent, and microtensile bond strength (μ-TBS) were investigated.

RESULTS

SKT prepared from the ionic liquid BMI.ZnCl₃ presented a hexagonal shape in the micrometer scale. SKT addition provided antibacterial activity against biofilm formation of S.mutans and planktonic bacteria (p < 0.05). There were no differences in pulp cells' viability (p > 0.05). The DC ranged from 62.18 (±0.83)% for control group to 64.44 (±1.55)% for 2.5 wt.% (p > 0.05). There was no statistically significant difference among groups for UTS (p > 0.05), softening in solvent (p > 0.05), and 24 h or 6 months μ-TBS (p > 0.05).

CONCLUSIONS

The physicochemical properties of adhesives were not affected by SKT incorporation, and the filler provided antibacterial activity against S. mutans without changes in the pulp cells' viability. This hybrid zinc-based particle with ionic liquid coating may be a promising filler to improve dental restorations.

CLINICAL RELEVANCE

A filler based on a zinc-derived material coated with ionic liquid was synthesized and added in dental adhesives, showing antibacterial activity and maintaining the other properties analyzed. SKT may be a promising filler to decrease the biofilm formation around resin-based restorative materials.

State of the Art on Biomaterials for Soft Tissue Augmentation in the Oral Cavity. Part II: Synthetic Polymers-Based Biomaterials

Most of the polymers used as biomaterials for scaffolds are naturally occurring, synthetic biodegradable, and synthetic non-biodegradable polymers. Since synthetic polymers can be adapted for obtaining singular desired characteristics by applying various fabrication techniques, their use has increased in the biomedical field, in dentistry in particular. The manufacturing methods of these new structures include many processes, such as electrospinning, 3D printing, or the use of computer-aided design/computer-aided manufacturing (CAD/CAM). Synthetic polymers show several drawbacks that can limit their use in clinical applications, such as the lack of cellular recognition, biodegradability, and biocompatibility. Moreover, concerning biodegradable polymers, the time for matrix resorption is not predictable, and non-resorbable matrices are preferred for soft tissue augmentation in the oral cavity. This review aimed to determine a new biomaterial to offset the present shortcomings in the oral environment. Researchers have recently proposed a novel non-resorbable composite membrane manufactured via electrospinning that has allowed obtaining remarkable in vivo outcomes concerning angiogenesis and immunomodulation throughout the polarization of macrophages. A prototype of the protocol for in vitro and in vivo experimentation with hydrogels is explained in order to encourage innovation into the development of promising biomaterials for soft tissue augmentation in the near future.

The Effects of Silver, Zinc Oxide, and Titanium Dioxide Nanoparticles Used as Dentin Pretreatments on the Microshear Bond Strength of a Conventional Glass Ionomer Cement to Dentin

Aim

This study was conducted to evaluate the effects of three nanoparticle solutions used as dentin pretreatments on the microshear bond strength (µSBS) of a conventional glass ionomer cement (GIC) to dentin.

Materials and Methods

Ninety intact human molars were used after sectioning their occlusal surfaces to expose flat dentin surfaces. The specimens were randomly assigned to nine groups (n = 10). Group A was the control group (without using the cavity disinfectant). In groups B, C, D, and E, the prepared dentin surfaces were treated with 1 cc 2% chlorhexidine (CHX), 0.1% silver nanoparticle (SNP), 0.1% titanium dioxide nanoparticle (TNP), and 0.1% zinc oxide nanoparticle (ZNP) solutions for 1 minute, respectively, before applying the conditioner. CHX, SNPs, TNPs, and ZNPs were applied for 1 minute after applying the conditioner in groups F, G, H, and I, respectively. The specimens were restored with a conventional GIC and underwent µSBS testing after 24 hours. The data were analyzed using the one-way analysis of variance and Tukey’s test (p=0.05).

Results

The applications of the nanoparticles (SNP, TNP, and ZNP) after the conditioner were associated with significantly greater µSBS values compared to that of the control group (p values < 0.05). Significantly higher µSBS values were observed when TNP or ZNP was applied after the conditioner compared to their applications before the conditioner (p values < 0.05). The highest µSBS values were observed when TNP was applied after the conditioner.

Conclusion

Dentin pretreatment with the nanoparticles after applying the conditioner enhanced the bond strength of the GIC to dentin compared with the control group. The best results were obtained for the TNPs applied after the conditioner.

Polymeric nanoparticles protect the resin-dentin bonded interface from cariogenic biofilm degradation

The objective was to assess doxycycline (Dox) and zinc (Zn) doped nanoparticles' (NPs) potential to protect the resin-dentin interface from cariogenic biofilm. Three groups of polymeric NPs were tested: unloaded, loaded with zinc and with doxycycline. NPs were applied after dentin etching. The disks were exposed to a cariogenic biofilm challenge in a Drip-Flow Reactor during 72 h and 7 d. Half of the specimens were not subjected to biofilm formation but stored 72 h and 7 d. LIVE/DEAD® viability assay, nano-dynamic mechanical assessment, Raman spectroscopy and field emission electron microscopy (FESEM) analysis were performed. The measured bacterial death rates, at 7 d were 46% for the control group, 51% for the undoped-NPs, 32% for Dox-NPs, and 87% for Zn-NPs; being total detected bacteria reduced five times in the Dox-NPs group. Zn-NPs treated samples reached, in general, the highest complex modulus values at the resin-dentin interface over time. Regarding the mineral content, Zn-NPs-treated dentin interfaces showed the highest mineralization degree associated to the phosphate peak and the relative mineral concentration. FESEM images after Zn-NPs application permitted to observe remineralization of the etched and non-resin infiltrated collagen layer, and bacteria were scarcely encountered. The combined antibacterial and remineralizing effects, when Zn-NPs were applied, reduced biofilm formation. Dox-NPs exerted an antibacterial role but did not remineralize the bonded interface. Undoped-NPs did not improve the properties of the interfaces. Application of Zn-doped NPs during the bonding procedure is encouraged. STATEMENT OF SIGNIFICANCE: Application of Zn-doped nanoparticles on acid etched dentin reduced biofilm formation and viability at the resin-dentin interface due to both remineralization and antibacterial properties. Doxycycline-doped nanoparticles also diminished oral biofilm viability, but did not remineralize the resin-dentin interface.

Zinc-Calcium-Fluoride Bioglass-Based Innovative Multifunctional Dental Adhesive with Thick Adhesive Resin Film Thickness

Apart from producing high bond strength to tooth enamel and dentin, a dental adhesive with biotherapeutic potential is clinically desirable, aiming to further improve tooth restoration longevity. In this laboratory study, an experimental two-step universal adhesive, referred to as Exp_2UA, applicable in both the etch-and-rinse (E&R) and self-etch (SE) modes and combining a primer, containing 10-methacryloyloxydecyldihydrogen phosphate as a functional monomer with chemical binding potential to hydroxyapatite, with a bioglass-containing hydrophobic adhesive resin, was multifactorially investigated. In addition to primary property assessment, including measurement of bond strength, water sorption, solubility, and polymerization efficiency, the resultant adhesive-dentin interface was characterized by transmission electron microscopy (TEM), the filler composition was analyzed by energy-dispersive X-ray spectroscopy, and the bioactive potential of the adhesive was estimated by measuring the long-term ion release and assessing its antienzymatic and antibacterial potential. Four representative commercial adhesives were used as reference/controls. Application in both the E&R and SE modes resulted in a durable bonding performance to dentin, as evidenced by favorable 1 year aged bond strength data and a tight interfacial ultrastructure that, as examined by TEM, remained ultramorphologically unaltered upon 1 year of water storage aging. TEM revealed a 20 μm thick hydrophobic adhesive layer with a homogeneous bioglass filler distribution. Adequate polymerization conversion resulted in extremely low water sorption and solubility. In situ zymography revealed reduced endogenous proteolytic activity, while Streptococcus mutans biofilm formation was inhibited. In conclusion, the three-/two-step E&R/SE Exp_2UA combines the high bonding potential and bond degradation resistance with long-term ion release, rendering the adhesive antienzymatic and antibacterial potential.

Doxycycline and Zinc Loaded Silica-Nanofibrous Polymers as Biomaterials for Bone Regeneration

The main target of bone tissue engineering is to design biomaterials that support bone regeneration and vascularization. Nanostructured membranes of (MMA)₁-co-(HEMA)₁/(MA)₃-co-(HEA)₂ loaded with 5% wt of SiO₂-nanoparticles (HOOC-Si-Membrane) were doped with zinc (Zn-HOOC-Si-Membrane) or doxycycline (Dox-HOOC-Si-Membrane). Critical bone defects were effectuated on six New Zealand-bred rabbit skulls and covered with the membranes. After six weeks, the bone architecture was evaluated with micro computed tomography. Three histological analyses were utilized to analyse bone regeneration, including von Kossa silver nitrate, toluidine blue and fluorescence. All membrane-treated defects exhibited higher number of osteocytes and bone perimeter than the control group without the membrane. Zn-HOOC-Si-Membranes induced higher new bone and osteoid area than those treated with HOOC-Si-Membranes, and control group, respectively. Zn-HOOC-Si-Membranes and Dox-HOOC-Si-Membranes attained the lowest ratio M1 macrophages/M2 macrophages. Dox-HOOC-Si-Membranes caused the lowest number of osteoclasts, and bone density. At the trabecular new bone, Zn-HOOC-Si-Membranes produced the highest angiogenesis, bone thickness, connectivity, junctions and branches. Zn-HOOC-Si-Membranes enhanced biological activity, attained a balanced remodeling, and achieved the greatest regenerative efficiency after osteogenesis and angiogenesis assessments. The bone-integrated Zn-HOOC-Si-Membranes can be considered as bioactive modulators provoking a M2 macrophages (pro-healing cells) increase, being a potential biomaterial for promoting bone repair.

Inhibition of matrix metalloproteinases: a troubleshooting for dentin adhesion

Matrix metalloproteinases (MMPs) are enzymes that can degrade collagen in hybrid layer and reduce the longevity of adhesive restorations. As scientific understanding of the MMPs has advanced, useful strategies focusing on preventing these enzymes' actions by MMP inhibitors have quickly developed in many medical fields. However, in restorative dentistry, it is still not well established. This paper is an overview of the strategies to inhibit MMPs that can achieve a long-lasting material-tooth adhesion. Literature search was performed comprehensively using the electronic databases: PubMed, ScienceDirect and Scopus including articles from May 2007 to December 2019 and the main search terms were “matrix metalloproteinases”, “collagen”, and “dentin” and “hybrid layer”. MMPs typical structure consists of several distinct domains. MMP inhibitors can be divided into 2 main groups: synthetic (synthetic-peptides, non-peptide molecules and compounds, tetracyclines, metallic ions, and others) and natural bioactive inhibitors mainly flavonoids. Selective inhibitors of MMPs promise to be the future for specific targeting of preventing dentin proteolysis. The knowledge about MMPs functionality should be considered to synthesize drugs capable to efficiently and selectively block MMPs chemical routes targeting their inactivation in order to overcome the current limitations of the therapeutic use of MMPs inhibitors, i.e., easy clinical application and long-lasting effect.

The effect of silver nanoparticles, zinc oxide nanoparticles, and titanium dioxide nanoparticles on the push-out bond strength of fiber posts

Background

This study was undertaken to investigate the effect of intraradicular dentin pretreatment with silver nanoparticles (SNPs), zinc oxide nanoparticles (ZNPs), and titanium oxide nanoparticles (TNPs) on the push-out bond strength (PBS) of fiber posts to root dentin using two types of resin cements.

Material and Methods

Eighty single-rooted human premolar roots were randomly divided into eight groups after endodontic treatment and post space preparation, according to the type of intraradicular dentin pretreatment with different nanoparticle solutions (n=20). The groups included no pretreatment (control) and pretreatments with SNPs, ZNPs, and TNPs. Each group was divided into 2 subgroups (n=10) according to cementation: Excite DSC/Variolink II and ED Primer II/Panavia F2.0. The PBS values were measured in different areas of the post space. The data were subjected to the three-way analysis of variance and Tukey tests (p=0.05).

Results

The SNP-pretreated groups showed significantly higher PBS values than the other groups. No significant differences in PBS were noted among the control, ZNP-pretreated, and TNP-pretreated groups. There was no significant difference in the PBS of the fiber posts with respect to cement type. The PBS was significantly lower in the apical region than in the other two regions. There was no statistically significant difference between the PBSs of the cervical and middle thirds.

Conclusions

Intraradicular dentin pretreatment with SNPs, TNPs, and ZNPs did not interfere with the PBS of the fiber posts. The best result was obtained for the SNP-pretreated groups for both types of cement. Also, the lowest PBS was found in the apical third of the root canal spaces.

Key words:Fiber post, nanoparticles, push-out bond strength.

Influence of meat and bone meal, phytase, and antibiotics on broiler chickens challenged with subclinical necrotic enteritis: 1. growth performance, intestinal pH, apparent ileal digestibility, cecal microbiota, and tibial mineralization

This study investigated the influence of meat and bone meal (MBM), phytase, and antibiotics (AB) on the performance, intestinal pH, ileal digestibility, cecal microbiota, and tibial mineralization in Ross 308 broilers challenged with necrotic enteritis (NE). A total of 672-day-old male Ross 308 chicks were allocated to 8 treatments with 6 replicate pens, with 14 birds each. The study employed a 2 × 2 × 2 factorial arrangement of treatments: MBM (no or yes), AB (no or yes, zinc bacitracin + salinomycin), and phytase level (500 or 1,500 FTU/kg; both using 500 matrix recommendations). Diets were based on wheat–soybean meal–canola meal. All birds were challenged with Eimeria spp on day 9 and Clostridium perfringens (C. perfringens) strain EHE-NE18 on day 14 and day 15. On day 21 (postchallenge), birds fed MBM had reduced weight gain (WG; P < 0.05) relative to without MBM. A 2-way phytase × AB interaction for WG on day 14 (P < 0.001) and day 21 (P < 0.001) and feed conversion ratio on day 21 (P < 0.001) and day 42 (P < 0.01) indicated positive effects of high phytase on bird performance in the presence of AB. On day 42, a 3-way MBM × phytase × AB interaction (P < 0.01) was observed for WG, showing high phytase increased WG with AB, relative to the birds without AB in the presence of MBM. A 2-way MBM × phytase interaction (P < 0.01) was observed for apparent ileal digestibility of Ca and P on day 16, whereby there was a notable reduction in Ca and P digestibility in birds fed MBM-free diets and a low phytase level, but with the high phytase level, Ca and P digestibility was not influenced by MBM. In conclusion, in NE challenged birds, high phytase has a beneficial effect on leg health and mineral utilization to the extent that it can replace MBM and has beneficial effects on bird performance in the presence of AB.

Nanoparticles as Anti-Microbial, Anti-Inflammatory, and Remineralizing Agents in Oral Care Cosmetics: A Review of the Current Situation

Many investigations have pointed out widespread use of medical nanosystems in various domains of dentistry such as prevention, prognosis, care, tissue regeneration, and restoration. The progress of oral medicine nanosystems for individual prophylaxis is significant for ensuring bacterial symbiosis and high-quality oral health. Nanomaterials in oral cosmetics are used in toothpaste and other mouthwash to improve oral healthcare performance. These processes cover nanoparticles and nanoparticle-based materials, especially domains of application related to biofilm management in cariology and periodontology. Likewise, nanoparticles have been integrated in diverse cosmetic produces for the care of enamel remineralization and dental hypersensitivity. This review summarizes the indications and applications of several widely employed nanoparticles in oral cosmetics, and describes the potential clinical implementation of nanoparticles as anti-microbial, anti-inflammatory, and remineralizing agents in the prevention of dental caries, hypersensitivity, and periodontitis.

The effects of zinc treatment on matrix metalloproteinases: A systematic review

BACKGROUND

Zinc (Zn) acts as a cofactor of matrix metalloproteinases (MMPs) and is vital for their activity and controlling their expression. Alteration of Zn in the body could affect the expression, activity, and destructive impacts of MMPs.

OBJECTIVE

This systematic review aimed to summarize existing evidence on the effects of Zn treatment on the expression and activity of MMPs.

METHOD

International sources from Pub Med, Scopus and Google Scholar were searched for the original and English-language studies, published up to the end of May 2018.

RESULTS

During the initial search, 179 records were found, and 135 articles of them remained after the exclusion of duplicate articles. 47 studies met the inclusion criteria, after multiple stages of screening and critical reviews of articles.

CONCLUSION

Approximately 62% of the included studies (29 of 47) showed an inhibitory impact of Zn on MMPs production and activities. The inhibitory or stimulatory effect of Zn on MMPs seems to depend on physiological conditions of the cells or animals used, dose of Zn used, and duration of treatment.

Bioactive Glass Applications in Dentistry

At present, researchers in the field of biomaterials are focusing on the oral hard and soft tissue engineering with bioactive ingredients by activating body immune cells or different proteins of the body. By doing this natural ground substance, tissue component and long-lasting tissues grow. One of the current biomaterials is known as bioactive glass (BAG). The bioactive properties make BAG applicable to several clinical applications involving the regeneration of hard tissues in medicine and dentistry. In dentistry, its uses include dental restorative materials, mineralizing agents, as a coating material for dental implants, pulp capping, root canal treatment, and air-abrasion, and in medicine it has its applications from orthopedics to soft-tissue restoration. This review aims to provide an overview of promising and current uses of bioactive glasses in dentistry.

Novel Polymeric Nanocarriers Reduced Zinc and Doxycycline Toxicity in the Nematode Caenorhabditis elegans

The objective was to evaluate the toxicity of zinc- and doxycycline-loaded polymeric nanoparticles (NPs) using Caenorhabditis elegans as a model organism. These NPs are composed of ethylene glycol dimethacrylate, 2-hydroxyethyl methacrylate and methacrylic acid. NPs were loaded with doxycycline (D-NPs) and zinc (Zn-NPs) by chemical adsorption, and loading efficacy was demonstrated. Worm death rate in a concentration-response curve basis was calculated for lethality. Metabolism was evaluated through pharyngeal pumping assay. Body length measurements, brood size and egg lays were used to gauge growth, reproduction and fertility respectively. Intracellular hydrogen peroxide levels were determined to assess the reactive oxygen species production. One-way ANOVA and Bonferroni were used for comparisons (p < 0.05). Tested NPs at the highest dosage did not affect lethality or worm metabolism, expressed in terms of death rate and pharyngeal pumping per minute, respectively. Zn-NPs slightly increased worm growth. The concentration of the intracellular hydrogen peroxide levels was the lowest in the D-NPs group. The distinct NPs and concentrations employed were shown to be non-toxic for in situ administration of zinc and doxycycline, reducing the harmful effects of these compounds.

Zinc oxide and copper nanoparticles addition in universal adhesive systems improve interface stability on caries-affected dentin

This study evaluated the MMP inhibition of the zinc oxide and copper nanoparticles (ZnO/CuNp), and the effects of their addition into adhesives on antimicrobial activity (AMA), ultimate tensile strength (UTS), in vitro degree of conversion (in vitro-DC), as well as, resin-dentin bond strength (μTBS), nanoleakage (NL) and in situ-DC on caries-affected dentin. Anti-MMP activity was evaluated for several MMPs. ZnO/CuNp (0% [control]; 5/0.1 and 5/0.2 wt%) were added into Prime&Bond Active (PBA) and Ambar Universal (AMB). The AMA was evaluated against Streptococcus mutans. UTS were tested after 24 h and 28d. After induced caries, adhesives and composite were applied to flat dentin surfaces, and specimens were sectioned to obtain resin-dentin sticks. μTBS, NL, in vitro-DC and in situ-DC were evaluated after 24 h. ANOVA and Tukey's test were applied (α = 0.05). ZnO/CuNp demonstrated anti-MMP activity (p < 0.05). The addition of ZnO/CuNp increased AMA and UTS (AMB; p < 0.05). UTS for PBA, in vitro-DC, in situ-DC and μTBS for both adhesives were maintained with ZnO/CuNp (p > 0.05). However, lower NL was observed for ZnO/CuNp groups (p < 0.05). The addition of ZnO/CuNp in adhesives may be an alternative to provide antimicrobial, anti-MMP activities and improves the integrity of the hybrid layer on caries-affected dentin.

Effect of sodium ascorbate on bond strength and metalloproteinases activity in bleached dentin

Aim

This study evaluated the effect of sodium ascorbate (SA) on the proteolytic activity of matrix metalloproteinases (MMPs) and investigated the related effects on the bond strength of bleached dentin.

Materials and methods

Eighty freshly extracted human third molars were randomly divided according to treatment (bleaching or SA application), type of analysis (microshear or measuring MMP activity), and post-bleaching time to assess bond strength (24 hrs or 30 days). Data from both analyses were subjected to one-way analysis of variance to detect differences among groups, followed by Tukey’s multiple comparison test (p≤0.05).

Results

Dental bleaching significantly reduced bond strength values when the adhesive strategy was performed after 24 hrs (despite the SA treatment) or 30 days after the bleaching procedure. However, after 30 days, the bond strength values of the groups who received bleaching or SA application were similar to those of the unbleached group. Dental bleaching caused the activation of MMPs, and SA did not influence this activity.

Conclusion

It was concluded that SA does not affect the activity of MMPs or the bond strength in bleached dentin immediately after the bleaching treatment.

Inhibitory effect of zinc-containing desensitizer on bacterial biofilm formation and root dentin demineralization

This study compared the effect of a novel zinc containing, Caredyne Shield (CS), and a fluoroaluminocalciumsilicate-based, Nanoseal (NS) desensitizers on dentin tubule occlusion, inhibition of Streptococcus mutans (S. mutans) biofilm growth, and resistance to bacterial demineralization. Desensitizers were applied to simulated hypersensitive bovine dentin, with distilled water used as a control. S. mutans biofilms were grown on the surface of each specimen in an oral biofilm simulator. CS showed the least bacterial count and water insoluble glucan amount followed by NS. Transverse micro radiography revealed that both CS and NS showed significant reduction in mineral loss and lesion depth of the associated lesion. Scanning electron micrographs showed that the two desensitizers formed obvious depositions on the dentin surfaces, occlusion of tubules and mineral tag formation.

Effects of silver diamine fluoride/potassium iodide on artificial root caries lesions with adjunctive application of proanthocyanidin

Treatment of carious root surfaces remains challenging due to the complex pathological processes and difficulty in restoring the original structure of root dentine. Current treatments targeting the de-/re-mineralisation processes are not entirely satisfactory in terms of the protection of the dentinal organic matrix and the highly organised structure of dentine. In this in vitro study, a cross-linking agent - proanthocyanidin (PA) was used in conjunction with a fluoride-based treatment - silver diamine fluoride/potassium iodide (SDF/KI) to putatively stabilise the organic dentinal framework as well as strengthen the collagen-mineral phase interaction. The effectiveness of this strategy was evaluated 24 h after application in terms of the distribution of ion uptake and microstructure of dentine after treatment as well as analysis of the nano-mechanical properties using a dynamic behaviour model. Results showed that individual use of SDF/KI significantly improved the surface microhardness and integrated mineral density (Z) up to 60 µm depth and the recovery of creep behaviour of demineralised dentine in the surface area compared to that treated with deionised distilled water (DDW). The combined treatment of PA and SDF/KI achieved a more homogenous mineral distribution throughout the lesions than SDF/KI alone; a more significant incremental increase in surface microhardness and Z was observed. Specifically, a superior effect on the subsurface area occurred with PA + SDF/KI, with significant improvements in microhardness, elastic modulus and recovery of creep behaviour of the demineralised dentine. Application of SDF/KI induced small discrete crystal formation distributed over the dentine surface and PA contributed to the formation of slit-shaped orifices of the dentinal tubules that were partially occluded. STATEMENT OF SIGNIFICANCE: Demographic transitions and improved oral health behaviour have resulted in increased tooth retention in elderly people. As a consequence, the risk of root dentine caries is increasing due to the age-associated gingival recession and the related frequent exposure of cervical root dentine. Root caries is difficult to repair because of the complex aetiology and dentine structure. The recovery of dentine quality depends not only on reincorporation of minerals but also an intact dentinal organic matrix and the organic-inorganic interfacial structure, which contribute to the biomechanics of dentine. With the capability of dentine modification, cross-linking agents were applied with a fluoride regimen, which improved its treatment efficacy of root caries regarding the distribution of ion uptake and recovery of dentine biomechanics.

Stored potential energy increases and elastic properties alterations are produced after restoring dentin with Zn-containing amalgams

The aim of this research was to ascertain the mechanical and chemical behavior of sound and caries-affected dentin (CAD), after the placement of Zn-free vs containing amalgam restorations. Peritubular and intertubular dentin were evaluated using, a) nanoindenter in scanning mode; the load and displacement responses were used to perform the nano-Dynamic mechanical analysis and to estimate the complex (E * ) and storage modulus (E'); b) Raman spectroscopy was used to describe the hierarchical cluster analysis (HCA). Assessments were performed before restoration placement and after restoring, and after 3 months of storage with thermocycling (100,000cy/5 °C and 55 °C). When CAD was treated with Zn-containing restorations, differences between E * and E' at both peritubular and intertubular dentin augmented, with energy concentration and production of implications in the mechanical performance of the restored teeth. E * and E' were very low at intratubular dentin of CAD restored with Zn-containing restorations. The relative presence of minerals, the phosphate crystallinity and the crosslinking of collagen increased their values at both types of dentin (peritubular and intertubular) when CAD was treated with Zn-containing restorations. The nature and secondary structure of collagen improved in CAD treated with Zn-containing amalgams. Different levels of dentin remineralization were revealed by hierarchical cluster analysis.

Modified Polymeric Nanoparticles Exert In Vitro Antimicrobial Activity Against Oral Bacteria

Polymeric nanoparticles were modified to exert antimicrobial activity against oral bacteria. Nanoparticles were loaded with calcium, zinc and doxycycline. Ions and doxycycline release were measured by inductively coupled plasma optical emission spectrometer and high performance liquid chromatography. Porphyromonas gingivalis, Lactobacillus lactis, Streptoccocus mutans, gordonii and sobrinus were grown and the number of bacteria was determined by optical density. Nanoparticles were suspended in phosphate-buffered saline (PBS) at 10, 1 and 0.1 mg/mL and incubated with 1.0 mL of each bacterial suspension for 3, 12, and 24 h. The bacterial viability was assessed by determining their ability to cleave the tetrazolium salt to a formazan dye. Data were analyzed by ANOVA and Scheffe’s F (p < 0.05). Doxycycline doping efficacy was 70%. A burst liberation effect was produced during the first 7 days. After 21 days, a sustained release above 6 µg/mL, was observed. Calcium and zinc liberation were about 1 and 0.02 µg/mL respectively. The most effective antibacterial material was found to be the Dox-Nanoparticles (60% to 99% reduction) followed by Ca-Nanoparticles or Zn-Nanoparticles (30% to 70% reduction) and finally the non-doped nanoparticles (7% to 35% reduction). P. gingivalis, S. mutans and L. lactis were the most susceptible bacteria, being S. gordonii and S. sobrinus the most resistant to the tested nanoparticles.

Zinc Metabolism and Metallothioneins

Among the trace elements, zinc is one of the most used elements in biological systems. Zinc is found in the structure of more than 2700 enzymes, including hydrolases, transferases, oxyreductases, ligases, isomerases, and lyases. Not surprisingly, it is present in almost all body cells. Preserving the stability and integrity of biological membranes and ion channels, zinc is also an intracellular regulator and provides structural support to proteins during molecular interactions. It acts as a structural element in nucleic acids or other gene-regulating proteins. Metallothioneins, the low molecular weight protein family rich in cysteine groups, are involved significantly in numerous physiological and pathological processes including particularly oxidative stress. A critical role of metallothioneins (MT) is to bind zinc with high affinity and to serve as an intracellular zinc reservoir. By releasing free intracellular zinc when needed, MTs mediate the unique physiological roles of zinc. MT expression is induced by zinc elevation, and thus, zinc homeostasis is maintained. That MT mediates the effects of zinc, besides having strong radical scavenging effects, points to the critical part it plays in oxidative stress. The present review aims to give information on metallothioneins, which have critical importance in the metabolism and molecular pathways of zinc.

Improved reactive nanoparticles to treat dentin hypersensitivity

The aim of this study was to evaluate the effectiveness of different nanoparticles-based solutions for dentin permeability reduction and to determine the viscoelastic performance of cervical dentin after their application. Four experimental nanoparticle solutions based on zinc, calcium or doxycycline-loaded polymeric nanoparticles (NPs) were applied on citric acid etched dentin, to facilitate the occlusion and the reduction of the fluid flow at the dentinal tubules. After 24 h and 7 d of storage, cervical dentin was evaluated for fluid filtration. Field emission scanning electron microscopy, energy dispersive analysis, AFM and Nano-DMA analysis were also performed. Complex, storage, loss modulus and tan delta (δ) were assessed. Doxycycline-loaded NPs impaired tubule occlusion and fluid flow reduction trough dentin. Tubules were 100% occluded in dentin treated with calcium-loaded NPs or zinc-loaded NPs, analyzed at 7 d. Dentin treated with both zinc-NPs and calcium-NPs attained the highest reduction of dentinal fluid flow. Moreover, when treating dentin with zinc-NPs, complex modulus values attained at intertubular and peritubular dentin were higher than those obtained after applying calcium-NPs. Zinc-NPs are then supposed to fasten active dentin remodeling, with increased maturity and high mechanical properties. Zinc-based nanoparticles are then proposed for effective dentin remineralization and tubular occlusion. Further research to finally prove for clinical benefits in patients with dentin hypersensitivity using Zn-doped nanoparticles is encouraged.

STATEMENT OF SIGNIFICANCE

Erosion from acids provokes dentin hypersensitivity (DH) which presents with intense pain of short duration. Open dentinal tubules and demineralization favor DH. Nanogels based on Ca-nanoparticles and Zn-nanoparticles produced an efficient reduction of fluid flow. Dentinal tubules were filled by precipitation of induced calcium-phosphate deposits. When treating dentin with Zn-nanoparticles, complex modulus values attained at intertubular and peritubular dentin were higher than those obtained after applying Ca-nanoparticles. Zn-nanoparticles are then supposed to fasten active dentin remodeling, with increased maturity and high mechanical properties. Zinc-based nanogels are, therefore, proposed for effective dentin remineralization and tubular occlusion. Further research to finally prove for clinical benefits in patients with dentin hypersensitivity using Zn-doped nanogels is encouraged.