Polymerization profile analysis of resin composite dental restorative materials in real time

Evaluation of depth-wise post-gel polymerisation shrinkage behaviour of flowable dental composites

Short fibre reinforced flowable dental composites are gaining acceptance over particulate filled composites due to their competence to impart improved physio-mechanical properties and capability to prevent crack propagation. However, limited research exists to assess their overall post-gel shrinkage behaviour, which is an important factor to determine marginal seal around restoration and hence its longevity. In this paper, depth-wise post-gel shrinkage strain and the resulting factors such as degree of conversion and rheological behaviour of flowable fibre reinforced composite (FRC) containing 5% weight fraction of 5 μm diameter, 350 μm length S-Glass fibres in UDMA/TEGDMA mixture along with 50% strontium filler particles were investigated. Post-gel shrinkage strain was measured using an array of optical fibre Bragg grating sensors (FBGs) of diameter 250 μm and length 1 mm each embedded at three different depths (depth 0 mm, depth 2.5 mm and depth 5 mm from curing light tip) within the flowable dental composite samples. The rheological behaviour during the polymerisation process was carried out using dynamic oscillatory tests. To evaluate the conversion of CC during polymerisation, degree of conversion tests were conducted by using FTIR spectroscopy. The results obtained for FRC samples were further compared with that of particulate filled composite (PFC) samples, with 55% strontium filler particles only within the same resin system. The relationship between post-gel shrinkage strain at different depths, rheological behaviour and degree of conversion was also explored. The experimental results from the sensor embedded materials suggested that the post-gel shrinkage strain was higher at the top surface (depth 0 mm) and was 50% more than at the bottom surface (depth of 5 mm) for dental FRC as well as PFC samples. Further, similar flow behaviour and not significant different (p<0.05) degree of conversion (DC), post-gel shrinkage strain for dental PFC and FRC composites was observed, establishing a convincing positive relationship between all the key factors and further implying that replacement of fibres with fillers did not affect the overall post-gel polymerisation shrinkage behaviour in dental composites. This investigation has also demonstrated that fibre optic sensors-based shrinkage measurements can be an ideal technique to evaluate post-gel shrinkage performance of dental resins with PFCs or FRCs.

Marginal Adaptation and Micropermeability of Class II Cavities Restored with Three Different Types of Resin Composites-A Comparative Ten-Month In Vitro Study

The development of composite materials is subject to the desire to overcome polymerization shrinkage and generated polymerization stress. An indicator characterizing the properties of restorative materials, with specific importance for preventing secondary caries, is the integrity and durability of marginal sealing. It is a reflection of the effects of polymerization shrinkage and generated stress. The present study aimed to evaluate and correlate marginal integrity and micropermeability in second-class cavities restored with three different types of composites, representing different strategies to reduce polymerization shrinkage and stress: nanocomposite, silorane, and bulk-fill composite after a ten-month ageing period. Thirty standardized class ΙΙ cavities were prepared on extracted human molars. Gingival margins were 1 mm apical to the cementoenamel junction. Cavities were randomly divided into three groups, based on the composites used: FiltekUltimate-nanocomposite; Filtek Silorane LS-silorane; SonicFill-bulk-fill composite. All specimens were subjected to thermal cycles after that, dipped in saline for 10-mounds. After ageing, samples were immersed in a 2% methylene blue. Thus prepared, they were covered directly with gold and analyzed on SEM for assessment of marginal seal. When the SEM analysis was completed, the teeth were included into epoxy blocks and cut longitudinally on three slices for each cavity. An assessment of microleakage on stereomicroscope followed. Results were statistically analyzed. For marginal seal evaluation: F.Ultimate and F.Silorane differ statistically with more excellent results than SonicFill for marginal adaptation to the gingival margin, located entirely in the dentin. For microleakage evaluation: F.Ultimate and F.Silorane differ statistically with less microleakage than SonicFill. Based on the results obtained: a strong correlation is found between excellent results for marginal adaptation to the marginal gingival ridge and micropermeability at the direction to the axial wall. We observe a more significant influence of time at the gingival margin of the cavities. There is a significant increase in the presence of marginal fissures (p = 0.001). A significant impact of time (p < 0.000) and of the material (p < 0.000) was found in the analysis of the microleakage.

Material behavior of resin composites with and without fibers after extended water storage

The objective of this study was to determine the long-term water sorption, solubility and hygroscopic expansion of resin composites with and without incorporated short fibers. Three resin composites incorporating fibers were examined: everX Posterior (EVX), NovoPro Universal (NPU) and NovoPro Flow (NPF). Four Particulate filled composites were used as controls: Filtek bulk Fill (FBF), Filtek one bulkfill (FBO), Filtek Supreme XTE (XTE), and Filtek Supreme Flow (XTEF). For sorption and solubility measurements, specimens were immersed in water for140 days, weighed at intervals, then dried for a further 42 days at 37±1°C. Laser micrometer measured diametral expansion. XTEF exhibited the highest sorption. The solubility range was between -1.4 to 4.1 μg/mm; XTEF had the highest solubility, with EVX demonstrating negative solubility. Hygroscopic expansion ranged between 1.4% for hydroxyapatite fiber reinforced composite (NPU) and 2.2% for E-glass fiber reinforced composite (EVX). A nano-fiber containing composite (NPU) had the most favorable outcomes compared to a range of composites.

Color stability of Bulk-Fill composite restorations

Background

The color stability of the composite resin is an important property that influences its clinical longevity, which remains an inherent challenge to the material. Thus, the purpose of this study was to evaluate the color stability of bulk-fill resins when exposed to dye.

Material and Methods

Cavities were prepared in 80 bovine incisors, which were randomly assigned into 4 groups (n = 20) according with the resin composite used: P60 (Control Group - Filtek P60, 3M/ESPE), FP (Filtek Bulk-Fill Posterior, 3M/ESPE), SDR (SDR, Dentsply) and FF (Filtek Bulk Fill Flow, 3M/ESPE). All restorations were performed according to the protocol of each manufacturer, the control group was restored using the incremental technique, and the other groups using single-increment technique. The color of each restoration was measured using a portable digital spectrophotometer (Easyshade-Vita) according to the CIELab system, and then the teeth were submerged in red wine for 07 days, kept in a biological oven at 37ºC. New color registration was performed to measure the ΔE index of color variation.

Results

The P60 group had the lowest average ΔE (16.96), while the FF group had the highest average (28.09) and ranged from 21.19 to 26.28 in the FP and SDR groups.

Conclusions

Analysis of the color variation showed that the control group had better color stability than the Bulk-Fill resins evaluated.

Key words:Dental restoration failure, Food coloring agents, polymerization.

Application of Antimicrobial Polymers in the Development of Dental Resin Composite

Dental resin composites have been widely used in a variety of direct and indirect dental restorations due to their aesthetic properties compared to amalgams and similar metals. Despite the fact that dental resin composites can contribute similar mechanical properties, they are more likely to have microbial accumulations leading to secondary caries. Therefore, the effective and long-lasting antimicrobial properties of dental resin composites are of great significance to their clinical applications. The approaches of ascribing antimicrobial properties to the resin composites may be divided into two types: The filler-type and the resin-type. In this review, the resin-type approaches were highlighted. Focusing on the antimicrobial polymers used in dental resin composites, their chemical structures, mechanical properties, antimicrobial effectiveness, releasing profile, and biocompatibility were included, and challenges, as well as future perspectives, were also discussed.

Nanofilled/nanohybrid and hybrid resin-based composite in patients with direct restorations in posterior teeth: A systematic review and meta-analysis

OBJECTIVE

A systematic review and a meta-analysis were performed to answer the following research question: Are there differences in the color match and surface texture of nanofilled/nanohybrid and hybrid composite in patients with direct posterior restorations?

DATA

Randomized clinical trials that compared nanofilled/nanohybrid and hybrid composite in direct restoration in posterior teeth were included. For the analysis of the bias the risk of bias tool (RoB) was used. Meta-analyses of different pairs (nanofilled vs. hybrid and nanohybrid vs. hybrid composite) were conducted for surface texture and color match and other secondary outcomes at different follow-ups, using a random effects model. Heterogeneity was assessed with the Cochran Q test and I² statistics. GRADE was used to assess the quality of the evidence.

SOURCES

A search was performed in PubMed, Scopus, Web of Science, LILACS, BBO, Cochrane Library and SIGLE, without restrictions. IADR abstracts (2001-2019), unpublished and ongoing trials registries, dissertations and theses were also searched.

STUDY SELECTION

28 studies remained. No study was considered to be at low RoB; four studies were judged to have high RoB, and the remaining were judged to have unclear RoB.

RESULTS

For the primary and secondary outcomes variables no significant differences were detected between nanofilled/nanohybrid restorations and hybrid composite restorations in any of the study follow-ups (p > 0.08). The body of evidence for surface texture and color match was classified as moderate or low.

CONCLUSION

No evidence of difference was found between nanofilled/nanohybrid and hybrid composite in any of the clinical parameters evaluated.

Effect of light-curing time on light-cure/post-cure volumetric polymerization shrinkage and regional ultimate tensile strength at different depths of bulk-fill resin composites

The aim of this study was to investigate volumetric polymerization shrinkage (VS), using swept-source optical coherence tomography (SS-OCT), of bulk-fill composites with different light-curing strategies; immediately after light-irradiation and after 24 h, and to evaluate their regional ultimate tensile strength (UTS) at different curing depths. The immediate VS after photo-polymerization decreased when the curing light-curing time was reduced from 20 to 10 to 5 s. On the other hand, their VS values after 24 h significantly increased due to the post-cure polymerization, resulting in similar VS values at all the light-curing times. Five seconds light-curing decreased the regional UTS of resin composites after the 24 h period compared with the 10 and 20 s light-curing regimes; therefore, the remarkable progress of post-cure polymerization after light-curing for a short time would not lead to an improvement in the mechanical properties of resin composites. The influence of the light-curing time on the curing depth was dependent upon the bulk-fill composite material.

Polymerisation Shrinkage Profiling of Dental Composites using Optical Fibre Sensing and their Correlation with Degree of Conversion and Curing Rate

Traditional polymerisation shrinkage (PS) measurement systems measure average PS of dental composites, but the true local PS varies along the length and breadth of the composite. The PS depends on the curing light intensity distribution, resultant degree of conversion (DOC) and the curing rate. In this paper, optical fibre Bragg grating (FBG) sensing based technology is used to measure the linear post-gel PS at multiple locations within dental composite specimens, and is correlated with DOC and curing rate. A commercial dental composite is used, and its post-gel PS and DOC are mapped using embedded fibre Bragg grating sensors at different curing conditions. The distance between the curing lamp and the composite specimen is varied which resulted in different intensity distribution across the specimen. The effect of curing light intensity distribution on PS, curing rate and DOC are investigated for demonstrating a relationship among them. It is demonstrated that FBG sensing method is an effective method to accurately profiling post-gel PS across the specimen.

Comparison of Er,Cr:YSGG Laser Handpieces for Class II Preparation and Microleakage of Silorane- or Methacrylate-Based Composite Restorations

OBJECTIVE

The aim of this study was to evaluate the influence of cavity preparation with different Er,Cr:YSGG laser handpieces on microleakage of different posterior composite restorations.

METHODS

Fifty-four extracted intact human premolars were randomly assigned to three groups according to cavity preparation method: Bur Group: high-speed diamond bur (Diatech), MD Group: Er,Cr:YSGG laser Waterlase MD handpiece (Biolase Millennium II), and Turbo Group: Er,Cr:YSGG laser Waterlase MD TURBO handpiece (Biolase Millennium II). One hundred eight Class II slot cavities were prepared on the mesial and distal proximal surfaces of each tooth, and the cavity preparation times required were determined. The groups were then subdivided according to the restorative systems used (n = 12): a conventional methacrylate-based microhybrid composite (Filtek P60+Adper Single Bond 2/3M); a silorane-based resin composite (Filtek Silorane+Silorane System Adhesive/3M); and a nanohybrid methacrylate-based composite (Kalore+G-Bond/GC). The restorative systems were applied according to the manufacturers' recommendations. Following thermocycling (X5000; 5°C-55°C), the teeth were coated with nail varnish except the restoration margins, immersed in 0.5% basic fuchsin dye solution, and sectioned in a mesiodistal direction. Dye penetration was evaluated under a light microscope for occlusal and cervical margins. Data were analyzed with one-way ANOVA and chi-square tests (p < 0.05).

RESULTS

The cavity preparation time (mean ± SD) required for Bur, MD, and Turbo group was 31.25 ± 3.82, 222.94 ± 15.85, and 92.5 ± 7.42 sec, respectively, and the differences among the groups were statistically significant (p < 0.05). Comparing the occlusal and cervical microleakage scores, no statistically significant differences were found among the groups and subgroups (p > 0.05).

CONCLUSIONS

Er;Cr:YSGG laser cavity preparation with the Turbo handpiece needed shorter time than the MD handpiece, although it needed longer time than the conventional diamond bur. The use of different handpieces of Er,Cr:YSGG laser did not differ from conventional preparation with diamond bur in terms of microleakage with the tested methacrylate- and silorane-based posterior composite restorative systems.

Polymerization Behavior and Mechanical Properties of High-Viscosity Bulk Fill and Low Shrinkage Resin Composites

The present study determined the mechanical properties and volumetric polymerization shrinkage of different categories of resin composite. Three high viscosity bulk fill resin composites were tested: Tetric EvoCeram Bulk Fill (TB, Ivoclar Vivadent), Filtek Bulk Fill posterior restorative (FB, 3M ESPE), and Sonic Fill (SF, Kerr Corp). Two low-shrinkage resin composites, Kalore (KL, GC Corp) and Filtek LS Posterior (LS, 3M ESPE), were used. Three conventional resin composites, Herculite Ultra (HU, Kerr Corp), Estelite ∑ Quick (EQ, Tokuyama Dental), and Filtek Supreme Ultra (SU, 3M ESPE), were used as comparison materials. Following ISO Specification 4049, six specimens for each resin composite were used to determine flexural strength, elastic modulus, and resilience. Volumetric polymerization shrinkage was determined using a water-filled dilatometer. Data were evaluated using analysis of variance followed by Tukey's honestly significant difference test (α=0.05). The flexural strength of the resin composites ranged from 115.4 to 148.1 MPa, the elastic modulus ranged from 5.6 to 13.4 GPa, and the resilience ranged from 0.70 to 1.0 MJ/m3. There were significant differences in flexural properties between the materials but no clear outliers. Volumetric changes as a function of time over a duration of 180 seconds depended on the type of resin composite. However, for all the resin composites, apart from LS, volumetric shrinkage began soon after the start of light irradiation, and a rapid decrease in volume during light irradiation followed by a slower decrease was observed. The low shrinkage resin composites KL and LS showed significantly lower volumetric shrinkage than the other tested materials at the measuring point of 180 seconds. In contrast, the three bulk fill resin composites showed higher volumetric change than the other resin composites. The findings from this study provide clinicians with valuable information regarding the mechanical properties and polymerization kinetics of these categories of current resin composite.

Effect of low shrinkage monomers on physicochemical properties of dental resin composites

The aim of this study was to evaluate the effect of low shrinkage monomers on physicochemical properties of dental resin composites. Two low shrinkage resin composites: one with a crosslink branching monomer (Kalore, GC Corp) and a novel monomer (Venus Diamond, Heraeus Kulzer) were compared to a conventional resin composite formulation (Filtek Z250, 3M/ESPE). The volumetric shrinkage was evaluated by µCT analysis (n=5) and the physicochemical properties by degree of C=C conversion (DC), flexural strength (FS) and Young's modulus (YM) (n=10). All samples were light cured by a LED device (Radii, SDI) with 16 J/cm2. The results were analysed by one-way ANOVA and Tukey test for multiple comparisons (α=0.05). No statistical difference was found between µCT shrinkage values to Kalore (1.8%) and Venus Diamond (1.7%) (p≥0.05); Z250 presented statistical highest shrinkage value (2.0%). Kalore presented higher statistical DC (60.8%) than Venus Diamond (49.5%) and Z250 (49.6%). No statistical difference was found between FS or YM properties to Venus Diamond and Z250; Kalore presented statistical lowest FS and YM properties (p≥0.05).

CONCLUSION

Using novel monomers seem to reduce polymerization shrinkage without affecting the physicochemical properties evaluated of resin composites rather than using crosslink branching monomers.

Cytotoxicity and cytokine expression induced by silorane and methacrylate-based composite resins

OBJECTIVE

The aim of this study was to evaluate cytotoxicity and cytokine production induced by light-cured or non-light-cured methacrylate-based and silorane composite resins in RAW 264.7 macrophages.

MATERIAL AND METHODS

Cells were stimulated with the extracts from light-cured or non-light-cured composite resins. After incubation for 24 h, cytotoxicity was assessed with the lactate dehydrogenase (LDH) and methyl thiazolyl tetrazolium (MTT) assays, and total protein was quantified using the Lowry method. TNF-α detection was examined with an enzyme-linked immunosorbent assay (ELISA) conducted with cell supernatants after cell stimulation for 6, 12, and 24 h. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey's post hoc test (α=0.05).

RESULTS

KaloreTM and FiltekTM Silorane were cytotoxic with or without light curing (p<0.05) after 24 h of incubation. KaloreTM stimulated the early production of TNF-α in comparison with control (p<0.05), whereas FiltekTM Silorane did not affect TNF-α levels after 6 and 12 h (p>0.05). However, after 24 h FiltekTM Silorane inhibited the production of TNF-α (p<0.05).

CONCLUSIONS

KaloreTM and FiltekTM Silorane were cytotoxic regardless of light curing. The extract obtained from KaloreTM after 15 days of incubation stimulated the production of TNF-α, unlike that obtained from FiltekTM Silorane.

Evaluation of the physical properties of dental resin composites using optical fiber sensing technology

OBJECTIVES

The characterization of the physical properties of dental resin composites is fraught with difficulties relating to significant intra and inter test parameter variabilities and is relatively time consuming and expensive. The main aim of this study was to evaluate whether optical fiber Bragg grating (FBG) sensing system may become a viable tool to study dental material characteristics. Of particular focus was the potential for the system to demonstrate a multi parameter all-in-one feature.

METHODS

A miniature FBG was embedded in six different dental resin composites and employed as a sensor to evaluate linear polymerization shrinkage, thermal expansion and water sorption. Six commercially available dental composites with different filler types and volume are evaluated. The tests are repeated with three sets of samples. The curing characteristics and residual strain gradient exhibited by the cured dental composites were also observed and commented.

RESULTS

Among the studied samples, SDR shows lowest polymerization shrinkage, while Beautifil FO3 shows the highest. The results also show clear distinction between particle filler type and fiber reinforcement based composites in their polymerization shrinkage properties. The agreement of the results with existing literatures show that FBG based system provides accurate results. Polymerization shrinkage rate of the samples are also obtained. Thermal expansion of the composites are measured using the FBG sensing method for the first time and is correlated with resin type, volume, filler type and glass transition temperature. The water sorption characteristics of the dental composite are also successfully measured using the FBG sensing method. The high level of repeatability and the low standard deviations shown in the results indicate good reliability with the use of FBG sensors.

SIGNIFICANCE

This study demonstrates how optical fiber technology can provide simple and reliable methods of measuring the critical physical properties of dental composites. In addition due to the embedding and preservation of the sensor within the samples multiple parameters can be tested for with the same sample. These features are expected to greatly assist material science researchers in dentistry as well as other biomedical fields. Of some interest the phenomenon of stress relaxation of dental composite at higher temperature was observed.

Effect of modulated photo-activation on polymerization shrinkage behavior of dental restorative resin composites

This study investigated the influence of modulated photo-activation on axial polymerization shrinkage, shrinkage force, and hardening of light- and dual-curing resin-based composites. Three light-curing resin composites (SDR bulk-fill, Esthet X flow, and Esthet X HD) and one dual-curing material (Rebilda DC) were subjected to different irradiation protocols with identical energy density (27 J cm(-2) ): high-intensity continuous light (HIC), low-intensity continuous light (LIC), soft-start (SS), and pulse-delay curing (PD). Axial shrinkage and shrinkage force of 1.5-mm-thick specimens were recorded in real time for 15 min using custom-made devices. Knoop hardness was determined at the end of the observation period. Statistical analysis revealed no significant differences among the curing protocols for both Knoop hardness and axial shrinkage, irrespective of the composite material. Pulse-delay curing generated the significantly lowest shrinkage forces within the three light-curing materials SDR bulk-fill, Esthet X flow, and Esthet X HD. High-intensity continuous light created the significantly highest shrinkage forces within Esthet X HD and Rebilda DC, and caused significantly higher forces than LIC within Esthet X flow. In conclusion, both the composite material and the applied curing protocol control shrinkage force formation. Pulse-delay curing decreases shrinkage forces compared with high-intensity continuous irradiation without affecting hardening and axial polymerization shrinkage.

Cytotoxicity of low-shrink composites with new monomer technology on bovine dental pulp-derived cells

Objectives:

The aim of this study was to evaluate the cytotoxicity of four low-shrink composites with new monomer technology on the bovine dental pulp-derived cells (bDPCs).

Materials and methods:

Ten samples were prepared for each group composites, and the samples were immersed in 7 mL of culture medium for 72 h at 37°C to extract residual monomer or cytotoxic substances. The culture medium containing the material extracts was sterile filtered for use on the cell cultures. Materials were incubated in medium with serum for 72 h. bDPCs were maintained in a medium with serum. A real-time cell analyzer was used to evaluate cell survival. After seeding 200 mL of the cell suspensions into the wells (10,000 cells/well) of the E-plate 96, bDPCs were treated with bioactive components released by the composite materials (1:1 and 1:2 dilutions) and monitored every 15 min for 50 h.

Results:

According to analysis of variance, there were significant differences between the cell indexes of the control and GC kalore ( p < 0.05) and Bisco Reflexions ( p < 0.001) groups for the 1:1 dilutions at 25 h. When evaluated at 50 h, 1:1 dilutions of GC Kalore ( p < 0.01) and Bisco Reflexions ( p < 0.001) reduced cell survival significantly.

Conclusions:

Although composites resins are being advanced, their cytotoxic effects have been proceeding till this time. However, two of the four materials tested significantly reduced cell viability when compared with control.

Clinical relevance:

Research should focus on the cytotoxicity of composites in addition to their mechanical properties.

Temperature-dependent polymerization shrinkage stress kinetics of resin-composites

OBJECTIVES

To determine temperature dependence of shrinkage stress kinetics for a set of resin composites formulated with dimethacrylate monomer matrices.

METHODS

Six representative resin composites with a range of resin matrices were selected. Two of them were considered as low shrinking resin composites: Kalore and Venus Diamond. The shrinkage stress kinetics at 23°C and 37°C were measured continuously using a Bioman instrument for 60min. Stress levels between materials were compared at two intervals: 2min and 60min. Specimen temperatures were controlled by a newly designed heating device. Stress measurements were monitored for 1h, after irradiation for 40s at 550mW/cm(2) (energy density=22J/cm(2)). Three specimens (n=3) were used at each temperature per material.

RESULTS

Shrinkage stress at 23°C ranged from 2.93MPa to 4.71MPa and from 3.57MPa to 5.42MPa for 2min and 60min after photo-activation, respectively. The lowest stress-rates were recorded for Kalore and Venus Diamond (0.34MPas(-1)), whereas the highest was recorded for Filtek Supreme XTE (0.63MPas(-1)). At 37°C, shrinkage stress ranged from 3.27MPa to 5.35MPa and from 3.36MPa to 5.49MPa for 2min and 60min after photo-activation, respectively. Kalore had the lowest stress-rate (0.44MPas(-1)), whereas Filtek Supreme XTE had the highest (0.85MPas(-1)). Materials exhibited a higher stress at 37°C than 23°C except for Kalore and Venus Diamond. Positive correlations were found between shrinkage stress and stress-rate at 23°C and 37°C (r=0.70 and 0.92, respectively).

SIGNIFICANCE

Resin-composites polymerized at elevated temperature (37°C) completed stress build up more rapidly than specimens held at 23°C. Two composites exhibited atypical reduced stress magnitudes at the higher temperature.

Influence of an intermediary base on the microleakage of simulated class II composite resin restorations

The aim of this in vitro study was to qualitatively and quantitatively evaluate the microleakage of Class II cavities restored with a methacrylate-based composite (Filtek Z250, 3M ESPE) or silorane-based composite (Filtek LS, 3M ESPE), varying the application of an intermediary base, using a low-viscosity composite resin (Filtek Z350 Flow, 3M ESPE) or resin-modified glass ionomer cement (RMGIC) (Vitrebond, 3M ESPE) and no intermediary base (control groups). Sixty cavities were prepared on the proximal surfaces of bovine teeth and were randomly divided according to the experimental groups (n=10). Following the restorative procedures and thermocycling, the samples were immersed in methylene blue for two hours. The qualitative evaluation was made using a stereomicroscope, whereby two observers analyzed the infiltration level of the dye within the tooth/filling. Microleakage scores among the groups were compared using the Kruskal-Wallis test followed by the Mann-Whitney test (p≤0.05). The samples were then ground and the powder was prepared for quantitative analysis in an absorbance spectrophotometer. The results were statistically analyzed by analysis of variance and the Tukey test (p≤0.05). Results from the quantitative analysis showed that LS presented higher values of microleakage than did Z250. There was a significant difference between both composites concerning the intermediary materials, with the lowest values obtained using RMGIC as an intermediary base. Results from the qualitative analysis showed that there were no statistically significant differences between composites; however, there were significant differences for both composites concerning the intermediary materials, with the lowest values obtained using RMGIC as an intermediary. It is possible to conclude that using RMGIC as an intermediary base provided lower microleakage, indicating better sealing of the tooth-restoration interface.

Polymerization development of "low-shrink" resin composites: Reaction kinetics, polymerization stress and quality of network

OBJECTIVES

To evaluate "low-shrink" composites in terms of polymerization kinetics, stress development and mechanical properties.

METHODS

"Low-shrink" materials (Kalore/KAL, N'Durance/NDUR, and Filtek P90/P90) and one control (Esthet X HD/EHD) were tested. Polymerization stress (PS) was measured using the Instron 5565 tensometer. Volumetric shrinkage (VS) was determined by the ACTA linometer. Elastic modulus (E) and flexural strength (FS) were obtained by a three-point bending test. Degree of conversion (DC) and polymerization rate (Rp) were determined by NIR spectroscopy (6165cm(-1) for dimethacrylates; 4156 and 4071cm(-1) for P90). Photopolymerization was performed at 740mW/cm(2)×27s. Glass transition temperature (Tg), degree of heterogeneity and crosslink density were obtained in a DMA for the fully cured specimens. Analysis of extracts was done by (1)H NMR. Data were analyzed with one-way ANOVA/Tukey's test (α=0.05).

RESULTS

The control presented the highest shrinkage and Tg. P90 showed the highest modulus, and NDUR demonstrated the highest conversion. The polymerization rates were comparable for all materials. NDUR and KAL had the highest and the lowest network homogeneity, respectively. The multifunctional P90 had the highest crosslink density, with no difference between other composites. The control had the greatest stress development, similar to NDUR. Crosslinking density and polymer network homogeneity were influenced by degree of conversion and monomer structure.

SIGNIFICANCE

Not all "low-shrink" composites reduced polymerization stress. P90 and NDUR had no leachable monomers, which was also a function of high crosslinking (P90) and high conversion (NDUR).

Influence of various irradiation processes on the mechanical properties and polymerisation kinetics of bulk-fill resin based composites

OBJECTIVES

To assess the effect of irradiation time and distance of the light tip on the micro-mechanical properties and polymerisation kinetics of two bulk-fill resin-based composites at simulated clinically relevant filling depth.

METHODS

Micro-mechanical properties (Vickers hardness (HV), depth of cure (DOC) and indentation modulus (E)) and polymerisation kinetics (real-time increase of degree of cure (DC)) of two bulk-fill resin-based composites (Tetric EvoCeram(®) Bulk Fill, Ivoclar Vivadent and x-tra base, Voco) were assessed at varying depth (0.1-6mm in 100μm steps for E and HV and 0.1, 2, 4 and 6mm for DC), irradiation time (10, 20 or 40s, Elipar Freelight2) and distances from the light tip (0 and 7mm). Curing unit's irradiance was monitored in 1mm steps at distances up to 10mm away from the light tip on a laboratory-grade spectrometer.

RESULTS

Multivariate analysis (α=0.05), Student's t-test and Pearson correlation analysis were considered. The influence of material on the measured mechanical properties was significant (η(2)=0.080 for E and 0.256 for HV), while the parameters irradiation time, distance from the light tip and depth emphasise a stronger influence on Tetric EvoCeram(®) Bulk Fill. The polymerisation kinetics could be described by an exponential sum function, distinguishing between the gel and the glass phase. The above mentioned parameters strongly influenced the start of polymerisation (gel phase), and were of less importance for the glass phase.

CONCLUSIONS

Both materials enable at least 4mm thick increments to be cured in one step under clinically relevant curing conditions.

CLINICAL SIGNIFICANCE

The susceptibility to variation in irradiance was material dependent, thus properties measured under clinically simulated curing conditions might vary to a different extent from those measured under ideal curing conditions.