Effect of resin shades on opacity of ceramic veneers and polymerization efficiency through ceramics

Light transmittance through resin-matrix composite onlays adhered to resin-matrix cements or flowable composites

OBJECTIVE

The aim of this study was to evaluate the influence of the thickness of resin-matrix composite blocks manufactured by CAD-CAM on the light transmittance towards different resin-matrix cements or flowable composites.

METHODS

Sixty specimens of resin-matrix composite CAD-CAM blocks reinforced with 89 wt% inorganic fillers were cross-sectioned with 2 or 3 mm thicknesses. The specimens were conditioned with adhesive system and divided in groups according to the luting material, namely: two dual-cured resin-matrix cements, two traditional flowable resin-matrix composites, and one thermal-induced flowable resin-matrix composite. Specimens were light-cured at 900 mW/cm2 for 40s. Light transmittance assays were preformed using a spectrophotometer with an integrated monochromator before and after light-curing. Microstructural analysis was performed by optical and scanning electron microscopy (SEM). Nanoindentation tests were performed to evaluate mechanical properties for indirect evaluation of degree of monomers conversion.

RESULTS

Optical and SEM images revealed low thickness values for the cementation interfaces for the traditional flowable resin-matrix composite. The cement thickness increased with the size and content of inorganic fillers. The highest light transmittance was recorded for the onlay blocks cemented with the traditional flowable resin-matrix composites while a group cemented with the dual-cured resin-matrix cement revealed the lowest light transmittance. The elastic modulus and hardness increased for specimens with high content of inorganic fillers as well as it increased in function of the light transmittance.

CONCLUSIONS

The light transmittance of flowable resin-matrix composites was higher than that for resin-matrix cement after cementation to resin-matrix composites blocks. The type, size, and content of inorganic fillers of the luting material affected the thickness of the cement layer and light transmittance through the materials.

CLINICAL RELEVANCE

On chair-side light curing, the transmission of visible light can be interfered by the chemical composition and viscosity of the luting materials. The increase in size and content of inorganic fillers of resin-matrix composites and luting materials can decrease the light transmittance leading to inefficient polymerization.

Effect of thickness of CAD/CAM materials on light transmission and resin cement polymerization using a blue light-emitting diode light-curing unit

OBJECTIVE

Evaluate the effect of thickness of high-translucency (HT) CAD/CAM materials on irradiance and beam profile from a blue light-emitting diode light-curing unit (LCU) and on the degree of conversion (DC) and maximum polymerization rate (Rp_max ) of a light-cured resin cement (LCC).

MATERIAL AND METHODS

The direct output from the LCU, the light transmission and irradiance ratio (IR) through one conventional composite and nine HT CAD/CAM materials (0.5, 1.0, 1.5, or 2.0-mm thick; n = 5) were measured with a integrating sphere coupled to a spectrometer. The light beam was assessed with a beam profiler camera. The DC at 600 s and the Rp_max of one LCC was determined using a Fourier transform infrared spectrometer (n = 5). Data were analyzed by ANOVA followed by Tukey's tests, and Dunnett's test was also used for irradiance data (α = 0.05).

RESULTS

A significant decrease in irradiance through all materials occurred as thickness increased. Thin CAD/CAM materials improved light homogeneity, which decreased with the increase in thickness. The DC of the LCC directly exposed to light was the same as when exposed to 45%, 25%, 15%, or 5% IRs. Rp_max decreased with the decrease in IR.

CONCLUSIONS

Although the HT CAD/CAM materials reduced the irradiance from the LCU, minor effects were observed in the LCC's DC.

CLINICAL SIGNIFICANCE

Despite the light attenuation of blue light through different CAD/CAM materials that were up to 2-mm thick, the degree of conversion of one brand of light-cured resin cement was clinically acceptable when the LCU was used for 30 s.

Effect of resin cement elastic modulus on the biaxial flexural strength and structural reliability of an ultra-thin lithium disilicate glass-ceramic material

OBJECTIVES

Photo- and dual-polymerized resin-based luting agent was evaluated for elastic moduli effects on ultra-thin lithium disilicate (LD) glass-ceramic strengthening, structural reliability, and stress distribution.

MATERIALS AND METHODS

One hundred-sixty LD discs (IPS e.max CAD, Ivoclar/Vivadent) were produced in ultra-thin thicknesses (half with 0.3 mm and the other half with 0.5 mm). The ultra-thin ceramic disks were coated with two different cement types (Variolink Veneer - V and Panavia F 2.0 - P). Two positive control groups were tested following hydrofluoric (HF) acid etching (LDt3, LDt5) and two negative control groups were tested for untreated ceramic (LD 3, LD 5). Biaxial flexural strength (BFS), characteristic strength (σ0) and Weibull modulus (m) were the response variables (n = 20) at the ceramic/resin cement interface (z = 0). Finite element analysis (FEA) was used to calculate maximum principal stress. Data were analyzed using two-way ANOVA, and Tukey's test. Scanning electron microscopy (SEM) was used to analyze the failed specimens using fractography and surface morphology.

RESULTS

The BFS of LD at either thickness was not affected by cement types, as also demonstrated by FEA. Structural reliability significantly improved in the positive control group (LDt5).

CONCLUSION

The cementation of ultra-thin LD with a resin-cement of varying elastic moduli did not influence BFS. LD surface modification by HF acid-etching increased the reliability.

CLINICAL RELEVANCE

Ultra-thin anterior veneer designs made from lithium disilicate have been widely proposed and the apparent success of LD ultra-thin veneers was not influenced by the cement choice in the current studies albeit the elastic moduli luting agents used were of similar values.

The effects of thickness and shade on translucency parameters of contemporary, esthetic dental ceramics

OBJECTIVE

To analyze translucency variations among four different contemporary esthetic ceramic systems having different shades and thicknesses.

MATERIAL AND METHODS

Ceramic specimens having different shades and translucencies were tested: leucite reinforced glass-ceramic (ECAD), conventional feldspathic ceramic (Noritake), zirconia reinforced lithium silicate glass-ceramic (Suprinity) and hybrid ceramic (Enamic). Specimens of 0.6, 0.9, 1.2, 1.5 and 2.0-mm thickness (n = 3/group, 615 total) were prepared. Translucency (TP) and Relative Translucency (RTP) Parameters were calculated from spectroradiometric color readings. Effects of shade and thickness for a given system were statistically analyzed using MANOVA and Tukey post-hoc multiple comparisons tests. Translucency variations were assessed comparatively with literature-based perceptibility and acceptability thresholds.

RESULTS

TP/RTP values of all ceramic materials decreased with increasing thickness. The most translucent specimens were 0.6-mm thick ECAD HT-A3.5 (TP = 31.99) and ECAD HT-C2 (RTP = 23.75), while the least translucent was 2-mm thick Enamic T-3 M2 (TP = 7.27; RTP = 4.79). Thickness and material type significantly influenced translucency (p < 0.001). Noritake and ECAD LT showed similar translucency values, as well as Suprinity HT and ECAD LT.

CONCLUSIONS

For ceramic restorations thicker than 0.9-mm, any thickness increase of 0.3-0.5 mm produces a perceptible but clinically acceptable translucency variation. Increases in thickness larger than 0.6-mm will result in an unacceptable translucency shift. Dental practitioners need to recognize key factors that influence translucency of ceramic restorations in order to choose the optimal material, shade, translucency, and thickness suitable for different clinical scenarios. While shade plays a minor role in translucency variation, ceramic type and restoration thickness significantly affect overall translucency.

Diagnostic accuracy of 870-nm spectral-domain OCT with enhanced depth imaging for the detection of caries beneath ceramics

OBJECTIVES

To evaluate the diagnostic accuracy of optical coherence tomography (OCT) for the non-invasive detection of caries adjacent to ceramic materials.

METHODS

Disks made from five ceramic materials (hybrid ceramic, feldspathic ceramic, zirconia-reinforced lithium silicate, lithium disilicate, and high-translucent zirconia) were ground to the recommended material thickness for single crown restorations and laminated with a 100 μm thick layer of one of three adhesive cements. The disks were fixed to extracted human molars with or without carious lesions of one of three standardized sizes. A total of 240 stacks of cross-sectional scans obtained using an 870-nm SD-OCT with enhanced depth imaging (EDI) were presented to five raters. Diagnostic accuracy was determined by rating the teeth beneath the cemented material as carious or healthy.

RESULTS

Carious samples were distinguished from sound teeth with high diagnostic accuracy, even for early stage caries. Sensitivity (SE) and specificity (SP) pooled over all raters and all materials were 0.9 and 0.97, respectively. When analyzing the effect of the ceramic and cement materials on detection rates, high SE and SP values of >0.96 and >0.91, respectively, were recorded for lithium disilicate, zirconia-reinforced lithium silicate, and high-translucent zirconia irrespective of the cement type. For hybrid and feldspathic ceramics, the cement material was found to have a significant effect on caries detection.

CONCLUSIONS

Given its high diagnostic accuracy, 870-nm SD-OCT with EDI might be useful for the detection of caries beneath restorative materials. The effect of the prescribed ceramic and cement material on optical penetration depth is substantial.

Evaluation of the Final Color of Ceramic Veneers with Different Self-Adhesive Resin Cements

Background:

Proper selection of cement plays an effective role in the success of ceramic laminate veneers. The cement can affect the final color by changing the optical properties of the ceramic.

Objective:

Due to the ease of clinical use of the seventh generation of cement (Self-Adhesive Cement), this study aimed to evaluate the effect of this type of cement on the final color of Ceramic Veneers (CV).

Methods:

In this study, 21 IPS e.max ceramic disks (8mm× 0.7 mm) were used. They were divided into 3 groups of 7, depending on the type of cement. (Choice 2, RelyX U200, Speed Cem). In the first stage, ceramic disks were set on the facial surface of bovine’s teeth by bonding agents and the color properties were analyzed by spectrophotometer. In the next stage, specimens were cemented on the prepared surfaces according to the manufacturer’s instructions and their color was evaluated subsequently.

Results:

Results were analyzed by repeated measures two-way ANOVA and TAMHANE post hoc methods (P < 0.05). Results showed that cement influences the color of the ceramic laminate. ∆E values were reported to be higher than the critical point after cementation (∆E > 2.69).

Conclusion:

There was no significant difference between the effects of three cement types on the final color of the ceramic veneers.

Light curing in dentistry and clinical implications: a literature review

Contemporary dentistry literally cannot be performed without use of resin-based restorative materials. With the success of bonding resin materials to tooth structures, an even wider scope of clinical applications has arisen for these lines of products. Understanding of the basic events occurring in any dental polymerization mechanism, regardless of the mode of activating the process, will allow clinicians to both better appreciate the tremendous improvements that have been made over the years, and will also provide valuable information on differences among strategies manufacturers use to optimize product performance, as well as factors under the control of the clinician, whereby they can influence the long-term outcome of their restorative procedures.

Dentist material selection for single-unit crowns: Findings from the National Dental Practice-Based Research Network

OBJECTIVES

Dentists enrolled in the National Dental Practice-Based Research Network completed a study questionnaire about techniques and materials used for single-unit crowns and an enrollment questionnaire about dentist/practice characteristics. The objectives were to quantify dentists' material recommendations and test the hypothesis that dentist's and practice's characteristics are significantly associated with these recommendations.

METHODS

Surveyed dentists responded to a contextual scenario asking what material they would use for a single-unit crown on an anterior and posterior tooth. Material choices included: full metal, porcelain-fused-to-metal (PFM), all-zirconia, layered zirconia, lithium disilicate, leucite-reinforced ceramic, or other.

RESULTS

1777 of 2132 eligible dentists responded (83%). The top 3 choices for anterior crowns were lithium disilicate (54%), layered zirconia (17%), and leucite-reinforced glass ceramic (13%). There were significant differences (p<0.05) by dentist's gender, race, years since graduation, practice type, region, practice busyness, hours worked/week, and location type. The top 3 choices for posterior crowns were all-zirconia (32%), PFM (31%), and lithium disilicate (21%). There were significant differences (p<0.05) by dentist's gender, practice type, region, practice busyness, insurance coverage, hours worked/week, and location type.

CONCLUSIONS

Network dentists use a broad range of materials for single-unit crowns for anterior and posterior teeth, adopting newer materials into their practices as they become available. Material choices are significantly associated with dentist's and practice's characteristics.

CLINICAL SIGNIFICANCE

Decisions for crown material may be influenced by factors unrelated to tooth and patient variables. Dentists should be cognizant of this when developing an evidence-based approach to selecting crown material.

Blue-Light Transmittance of Esthetic Monolithic CAD/CAM Materials With Respect to Their Composition, Thickness, and Curing Conditions

Determining the amount of blue light (360-540nm) passing through nine monolithic computer-aided design/computer-aided manufacturing (CAD/CAM) materials depends on material thickness, initial irradiance, and the distance between the curing unit and the specimen's surface. A total of 180 specimens of two thicknesses (1 mm and 2 mm, n=10/subgroup) were fabricated from TelioCAD, VITA CAD-Temp (VCT), experimental nanocomposite, LAVA Ultimate (LU), VITA ENAMIC (VE), VITA MarkII (VM), IPS EmpressCAD (IEC), IPS e.maxCAD (IEM), and CELTRA DUO (CD). The irradiance passing through the CAD/CAM materials and thicknesses was measured using a light-emitting-diode curing unit with standard-power, high-power, and plasma modes by means of a USB4000 spectrometer. The curing unit was placed directly on the specimen's surface at 2- and 4-mm distances from the specimen's surface. Data were analyzed using a multivariate analysis and one-way analysis of variance with the post hoc Scheffé test (p&lt;0.05). The highest transmitted irradiance was measured for VM and LU, followed by VCT and IEC, while the lowest values showed VE, followed by IEM and CD. The highest transmitted irradiance was recorded by exposing the material to the plasma mode, followed by the high- and standard-power modes. The measured irradiance was decreased by increasing the specimen's thickness from 1 to 2 mm. Fewer differences were measured when the curing unit was placed at 0 or 2 mm from the specimen's surface, and the irradiance passing through the specimens was lower at a distance of 4 mm.

Effect of ceramic thickness and cement shade on the final shade after bonding using the 3D master system: a laboratory study

The final color of a ceramic restoration is influenced by both the ceramic thickness and the cement shade. This study aims to evaluate the color stability according to the 3D Master System of e.max ceramic discs after bonding with different shades of luting agents. A total of 120 e.max.Press 2M1 HT ceramic discs (60 discs of 1-mm thick and 60 discs of 0.5 mm thick) and three different values of Variolink Veneer cement were used (-3, 0, +3) for the cementation process. An Easyshade compact device was used to measure color shade tabs, according to the 3D Master System, on the discs both before and after the cementation protocols. Bivariate and multivariate analyses were carried out with the spss v.21. After bonding with the different luting agents, only 30% remained as 2M1: specifically, 22% of the thinner discs and 37.3% of the thicker discs. In general, the effect of bonding increased the value and the chroma of the shade to a significant extent. Regression analyses revealed that the most significant predictor for all color parameters was cement shade, the thinner disc group bonded with -3 cement being the most unstable subgroup. According to the 3D Master System, the shade of the luting agent was the main predictor of the final color. However, the final color seems to be somewhat unpredictable, at least according to the modulating factors evaluated in the present study.

Indirect Restoration Thickness and Time after Light-Activation Effects on Degree of Conversion of Resin Cement

<p>This study evaluated the effects of indirect restorative materials, curing conditions and time on the degree of conversion (DC) of a dual-cured resin cement using infrared spectroscopy. The resin cement (RelyX Unicem 2, 3M ESPE) was applied to the diamond surface of a horizontal attenuated-total-reflectance unit and activated using one of following conditions: self-cure, direct light exposure, light exposure through indirect restorative materials (resin nano-ceramic: Lava Ultimate, 3M ESPE or feldspathic ceramic: Vita Blocks Mark II, Vita Zahnfabrik). Four thicknesses (0.5, 1.0, 1.5 or 2.0 mm) of each indirect material were analyzed, and the light-activation was performed using a blue LED light. Data (n=5) were analyzed by three-way ANOVA, Tukey's post hoc and Dunnett's tests (α=5%). No significant differences in DC were observed between indirect materials of similar thickness. All groups exhibited higher DC after 10 min than after 5 min. At both times points, the self-cure group exhibited significantly lower DC than all the light exposure groups. Only when the overlying indirect restoration had a thickness of 2 mm did DC decrease significantly. The presence of a thick, indirect restoration can decrease the DC of resin cement. DC after 10 min was higher than after 5 min. The self-cure mode yielded lower DC than the light-activating one.</p>

Translucency of esthetic dental restorative CAD/CAM materials and composite resins with respect to thickness and surface roughness

STATEMENT OF PROBLEM

Little information is available about the translucency of monolithic CAD/CAM materials.

PURPOSE

The purpose of this study was to evaluate the translucency of restorative CAD/CAM materials and direct composite resins with respect to thickness and surface roughness.

MATERIALS AND METHODS

In total, 240 disk-shaped specimens (12×14×1 mm and 12×14×2 mm) of 3 different CAD/CAM glass ceramics (CELTRA Duo, IPS e.max CAD, IPS Empress CAD), a fine-structure feldspathic ceramic (VITA Mark II), a hybrid ceramic (VITA Enamic), a resin nanoceramic composite resin (LAVA Ultimate), an experimental (CAD/CAM nanohybrid composite resin), 2 interim materials (Telio CAD; VITA CAD-Temp), and 3 direct composite resins (Tetric EvoCeram; Filtek Supreme XTE; Tetric EvoCeram Bulk Fill) were fabricated (n=10). After 3 different surface pretreatments (polished, rough SiC P1200, or SiC P500), absolute translucency and surface roughness were measured using spectrophotometry and tactile profilometry. The influence of material type, thickness, and roughness on absolute translucency was analyzed using a multivariate analysis, 1-way ANOVA, and the Tukey HSD post hoc test (P<.05). Pearson correlations and statistical hypothesis tests were used to assess the results (P<.05).

RESULTS

The effect of all tested parameters was significant among the materials (P<.05). The greatest influence on the measured translucency was thickness (partial eta squared ηP²=.988), closely followed by material (.982), and the pretreatment method (.835). The surface roughness was strongly influenced by the pretreatment method (.975) and type of material (.941).

CONCLUSION

Thickness and surface roughness are major factors affecting the absolute translucency of adhesively luted restorations.

Effects of ceramic shade and thickness on the micro-mechanical properties of a light-cured resin cement in different shades

OBJECTIVE

The aim of this study was to evaluate the micro-mechanical properties of a light-cured resin cement in four different shades when polymerized through a leucite-reinforced glass-ceramic in different shades and thicknesses.

MATERIALS AND METHODS

A light-cured resin cement in four different shades (HV+1, HV+3, LV-1 and LV-3) was selected for this study. The specimens were cured by using a LED-unit (Bluephase®, IvoclarVivadent) for 20 s under a leucite-reinforced glass-ceramic (IPS Empress® CAD, IvoclarVivadent) in two different shades (A1 and A3) of different thicknesses (1 and 2 mm). Specimens cured directly, without an intermediate ceramic, served as control. The specimens were stored after curing for 24 h at 37°C by maintaining moisture conditions with distilled water. Micro-mechanical properties (indentation modulus, E; Hardness, HV; creep, Cr) of the resin cements were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Twenty groups were included (n = 3), while 10 measurements were performed on each specimen. Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters.

RESULTS

Significant differences were observed between the micromechanical properties of the tested resin cements (p < 0.05). The resin cement shade showed the highest effect on the micromechanical properties (Partial-eta squared (ηP(2))-E = 0.45, ηP(2)-HV = 0.59, ηP(2)-Cr = 0.29) of the resin cement, followed by ceramic thickness (ηP(2)-E = 0.38, ηP(2)-HV = 0.3, ηP(2)-Cr = 0.04) and ceramic shade (ηP(2)-E = 0.2, ηP(2)-HV = 0.26).

CONCLUSIONS

Resin cement shade is an important factor influencing the mechanical properties of the material. Light shades of a resin cement express higher E and HV as well as lower Cr values compared with the darker ones.