Altering of optical and mechanical properties in high-translucent CAD-CAM resin composites during aging

Influence of Post-Curing in Nitrogen-Saturated Condition on the Degree of Conversion and Color Stability of 3D-Printed Resin Crowns

Post-curing is the process of applying extra light to complete the polymerization process of 3D printing. The mechanical properties of light-cured three-dimensional (3D) printed resin can be improved by decreasing the oxygen concentrations during post-curing, and nitrogen-saturated post-curing has been applied for this purpose. This study aimed to evaluate and compare the color stability of 3D-printed resin crowns that were post-cured in both normal air and nitrogen-saturated conditions. Crowns were fabricated with a 3D printer and post-cured in normal air (control group; air) or nitrogen-saturated conditions (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed using repeated-measures ANOVA. Fourier transform infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Upon comparing the effects of post-curing conditions, a significant difference between the control and experimental groups in terms of immersion time in the wine and curry subgroups was found. FT-IR analysis showed a significant difference in the degree of conversion between the air and nitrogen groups from 10 to 300 s. These findings suggest that nitrogen-saturated post-curing can potentially enhance the conversion rate of 3D-printed resin crowns, thereby improving their color stability.

Aging and Fracture Resistance of Implant-Supported Molar Crowns with a CAD/CAM Resin Composite Veneer Structure

Chipping of implant-supported molar crowns (iSCs) is a frequently reported complication. This study aimed to investigate the in-vitro aging and fracture resistance of iSCs with a CAD/CAM resin composite veneer structure fabricated with the Rapid Layer Technology (RLT) approach. Eight iSCs per group were fabricated by using two different CAD/CAM resin composites (Shofu Block HC: SH; Grandio blocs: GB) for veneer structures, and zirconia (ZrO2), polyetheretherketone (PEEK), and cobalt-chromium (CoCr; control) as framework materials. The surfaces to be bonded were sandblasted, cleaned in an ultrasonic bath, and a coupling agent was applied. A self-adhesive resin luting composite was used to adhesively lute the veneer structures to the frameworks. The crowns were semi-permanently cemented to the abutments. After storage in deionized water, iSCs were loaded in a chewing simulator (TCML, 10,000 thermal cycles 5 °C to 55 °C for 20 s, 1.2 million, loading force 50 N). Four ZrO2 and one CoCr crown did not survive the TCML. The fracture force was determined after 24 h storage in deionized water and yielded values of ≥974 N. Lowest fracture forces were yielded in the PEEK-SH group in comparison to CoCr or ZrO2 groups (p ≤ 0.031). For identical framework materials, no significant influence of the veneering material was observed. All PEEK-GB frameworks fractured, and chipping occurred for ZrO2-SH and all CoCr frameworks. PEEK-SH and ZrO2-GB presented both chipping and framework fractures. Within the limitations of this in-vitro study, the RLT with a CAD/CAM resin composite veneer structure might be a promising approach to veneer iSCs. Yet, the choice of the CAD/CAM resin composite and of the framework material determine the fracture resistance.

In vitro evaluation of CAD/CAM composite materials

OBJECTIVES

The purpose of this in vitro study was to evaluate the microstructural, elemental and mechanical properties of contemporary computer-aided-design/computer-aided manufacturing (CAD/CAM) resin based composite (RBC) materials.

METHODS

Six CAD/CAM RBC materials [Brilliant CRIOS (Coltene Whaledent AG), Cerasmart (GC), Lava Ultimate (3M ESPE), Tetric CAD (Ivoclar Vivadent), Shofu Block HC (Shofu), Grandio Blocs (VOCO GmbH)] were tested. Ten rectangular blocks (14 Χ 12 Χ 18 mm) for each material, after metallographic grinding and polishing, were subjected to Instrumented Indentation Testing (ΙIT). Martens Hardness (HM), Indentation Elastic Modulus (EIT), Elastic (ηIT) and Creep indices (CIT) were determined according to formulas provided by ISO 14577. The diagonal length of each indentation was measured and HV was determined. The results of HM, EIT, ηΙΤ, HV, and CIT were statistically analyzed by one-way ANOVA and Tukey post hoc test employing the material as a discriminating variable (a = 0.05), while the possible correlations were determined by Spearman's correlation test. One specimen from each group was examined by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX).

RESULTS

Backscattered Electron images and EDX analysis demonstrated differences in size, shape and type of fillers along with elemental composition among materials tested. Statistical significant differences were identified for all mechanical properties tested. Grandio Blocs had the significantly higher HM (953±7 N/mm2), HV (136±1) and EIT (23±1 GPa) followed by Lava Ultimate (ΗM=674±25 N/mm2, HV=105±2, EIT=15±1 GPa). Elastic index ranged from 41% to 52%, with Shofu Block demonstrating the significantly highest ηIT (52 ± 1%) values. Cerasmart had significantly higher CIT value (8.4 ± 0.1%) than all other materials tested, while Grandio Blocs and Lava Ultimate had the lowest ones. Spearman's correlation revealed that all mechanical properties tested exhibited correlations with each other, apart from ηΙΤ.

CONCLUSIONS

The results showed that the CAD/CAM materials tested have differences in their microstructure, elemental composition and mechanical properties.

CLINICAL SIGNIFICANCE

The RBCs tested showed significant differences in mechanical properties and thus differences in clinical performance are anticipated. RBCs with increased filler loading had the most favorable combination of hardness, elastic modulus and creep index indicating that these materials may have better clinical performance under intraoral loading conditions.

Shade, Aging and Spatial-Dependent Variation of Elastoplastic and Viscoelastic Characteristics in a Dental, Submicron Hybrid CAD/CAM Composite

This article reports the elastoplastic and viscoelastic response of an industrially cured CAD/CAM resin-based composite (Brilliant Crios, Coltene) at different scales, spatial locations, aging conditions, and shading. Mechanical tests were performed at the macroscopic scale to investigate material strength, elastic modulus, fracture mechanisms and reliability. An instrumented indentation test (IIT) was performed at the microscopic level in a quasi-static mode to assess the elastic and plastic deformation upon indentation, either by mapping transverse areas of the CAD/CAM block or at randomly selected locations. A dynamic-mechanical analysis was then carried out, in which chewing-relevant frequencies were included (0.5 to 5 Hz). Characteristics measured at the nano- and micro-scale were more discriminative in identifying the impact of variables as those measured at macro scale. Anisotropy as a function of the spatial location was identified in all shades, with gradual variation in properties from the center of the block to peripheral locations. Depending on the scale of observation, differences in shade and translucency are very small or not statistically significant. The aging effect is classified as low, but measurable on all scales, with the same pattern of variation occurring in all shades. Aging affects plastic deformation more than elastic deformation and affects elastic deformation more than viscous deformation.

Evaluation of Physical-Chemical Properties of Contemporary CAD/CAM Materials with Chromatic Transition "Multicolor"

The use of materials for computer-aided design/computer-aided manufacturing (CAD/CAM) has been rapidly increasing in daily practice. However, one of the main issues regarding modern CAD/CAM materials is their aging in the oral environment, which may lead to significant changes in their overall properties. The aim of this study was to compare the flexural strength, water sorption, cross-link density (softening ratio%), surface roughness, and SEM analysis of three modern CAD/CAM "multicolor" composites. Grandio (Grandio disc multicolor-VOCO GmbH, Cuxhaven, Germany), Shofu (Shofu Block HC-Shofu Inc., Kyoto, Japan), and Vita (Vita Enamic multiColor-Vita Zahnfabrik, Bad Sackingen, Germany) were tested in this study. They were prepared in stick-shaped specimens and submitted to different tests after several aging protocols, such as thermocycling and mechanical cycle loading challenge. Further disc-shaped specimens were also created and tested for water sorption, cross-link density, surface roughness, and SEM ultramorphology, before and after storage in an ethanol-based solution. For flexural strength and ultimate tensile strength, Grandio showed the greatest values both at baseline and after aging (p < 0.05). Grandio and Vita Enamic presented the highest modulus of elasticity and the lowest water sorption (p < 0.05). A significant reduction (p < 0.05) in microhardness after ethanol storage (softening ratio%) was observed especially in Shofu. Grandio had the lowest roughness parameters compared to the other tested CAD/CAM materials, while ethanol storage significantly increased the Ra and RSm values in Shofu (p < 0.05). Despite the comparable modulus of elasticity of Vita and Grandio, this latter showed greater flexural strength and ultimate tensile strength both at baseline and after aging. Hence, Grandio and Vita Enamic may be employed for the anterior teeth and for those restorations requiring load-bearing capacity. Conversely, aging seems to affect several properties of Shofu, so its use for permanent restorations should be well-pondered based on the clinical situation.

Light Transmission Characteristics and Cytotoxicity within A Dental Composite Color Palette

Modern light-cured, resin-based composites are offered in a wide range of shades and translucencies. This large variation, created by varying the amount and type of pigmentation and opacifiers, is essential to enable an esthetic restoration in each patient situation, but may affect light transmission in the deeper layers during curing. We quantified optical parameters and their real-time variation during curing for a 13-shade composite palette of identical chemical composition and microstructure. Incident irradiance and real-time light transmission through 2 mm thick samples were recorded to calculate absorbance, transmittance, and the kinetic of transmitted irradiance. Data were supplemented by the characterization of cellular toxicity to human gingival fibroblasts up to 3 months. The study highlights a strong dependence of light transmission and its kinetic as a function of shade, with the largest changes occurring within the first second of exposure; the faster changes, the darker and more opaque the material. Transmission differences within progressively darker shades of a pigmentation type (hue) followed a hue-specific, non-linear relationship. Shades with similar transmittance but belonging to different hues were identified, while the corresponding kinetic was identical only up to a transmittance threshold. A slight drop in absorbance was registered with increasing wavelength. None of the shades were cytotoxic.

The influence of different storage media on Vickers hardness and surface roughness of CAD/CAM resin composites

INTRODUCTION

This study examined Vickers hardness as well as surface characteristics of different computer-aided design/computer-aided manufacturing (CAD/CAM) resin composites prior to and after storage in various media.

MATERIALS AND METHODS

CAD/CAM resin composite blocks (Grandio Blocs (GB), Lava Ultimate (LU), Brilliant Crios (BC), Cerasmart (GC), Shofu Block HC (SB), Tetric CAD (TC), Luxacam Composite (LC); incl. different translucency variants) were prepared, polished and surface free energy was determined. The specimens were divided into four groups: dry conditions for 24 h (25 °C), demineralized water (37 °C), Pepsi Cola (37 °C) and 75% ethanol (37 °C). After seven and 28 days of storage, Vickers hardness was determined. Surface roughness was measured after the entire storage period.

RESULTS AND DISCUSSION

Vickers hardness was in the range of about 150 HV for GB, around 115 HV for LU, and 80-100 HV for BC, GC, SB, TC and LC. Only minor differences (total: 50.2 (6.4)-56.2 (3.2) mN/m) in surface free energy could be detected. No relationship was observed between surface free energy and filler content. However, a correlation between filler content and Vickers hardness was evident. Artificial aging caused a decrease of Vickers hardness (up to -40 HV or 35%) depending on storage media, duration and material. The changes in surface texture after immersion in different media were below a value of ΔSa = 0.015 µm.

CONCLUSION

Artificial aging of CAD/CAM resin composites leads to a significant decrease of Vickers hardness for most materials, while only small changes in surface roughness were identified.

Martens Hardness of CAD/CAM Resin-Based Composites

(1) Background: The properties of CAD/CAM resin-based composites differ due to differences in their composition. Instrumented indentation testing can help to analyze these differences with respect to hardness, as well as energy-converting capabilities due to viscoelastic behavior. (2) Methods: Eleven materials were investigated using instrumented indentation testing. Indentation depth (hr), Martens hardness (HM), indentation hardness (HIT), indentation modulus (EIT), the elastic part of indentation work (ηIT), and indentation creep (CIT) were investigated, and statistical analysis was performed using one-way ANOVA, Bonferroni post-hoc test, and Pearson correlation (α = 0.05). (3) Results: All of the investigated parameters revealed differences between the analyzed materials. Besides the differences in hardness-associated parameters (hr, HM, and HIT), instrumented indentation testing demonstrated differences in energy-converting properties. The subsequent one-way ANOVA revealed significant differences (p < 0.001). A significant (p < 0.01, Pearson correlation >0.576) correlation between the materials and HM, HIT, or EIT was identified. (4) Conclusions: Due to the differences found in the energy-converting properties of the investigated materials, certain CAD/CAM resin-based composites could show superior stress-breaking capabilities than others. The consequential reduction in stress build-up may prove to beneficial, especially for implant-retained restorations or patients suffering from parafunctions.

Translucency of a Dental Porcelain Mixed by Two Ceramic Slurry Methods: A Bayesian Comparison

Background

The ceramics industry produces porcelain pastes using a controlled ratio of water and porcelain powder. Two methods are used to produce a dental porcelain paste: one-step mixing or incremental mixing.

Objective

To evaluate the optical properties of a feldspathic dental ceramic using two different ceramic paste preparation methods using a Bayesian approach.

Materials and Methods

Two groups of feldspathic porcelain discs, an incremental mixing group (n = 40) and a one-step mixing group (n = 40), were assessed. Groups were evaluated using spectrophotometry, and the translucency parameter (TP) of each sample was calculated. Surfaces were characterized by AFM and SEM. Statistical analysis was performed using a Bayesian approach.

Results

Translucency parameter values of the incremental mixing group ranged from 1.65 to 3.41, while values for the one-step mixing group ranged from 3.62 to 5.74, this difference being statistically significant. The lowest roughness was obtained on the surface of discs in the one-step mixing group.

Conclusions

Feldspathic porcelain with lower translucency and higher roughness was obtained using the incremental mixture method.

Shear-bond strength and optical properties of short fiber-reinforced CAD/CAM composite blocks

The aim of this study was to assess the shear-bond strength (SBS) of resin-luting cement to experimental short fiber-reinforced CAD/CAM composite (SFRC) compared to conventional CAD/CAM (Cerasmart 270), 3D printed (GC TEMP PRINT, Pro3dure GR-17), and laboratory (Gradia Plus) composites. Moreover, translucency parameter values and light transmission were evaluated. For each of the five types of composites, discs were prepared (n = 16/group) and divided into subgroups (n = 8/group) according to surface treatment protocol (hydrofluoric acid or air-particle abrasion). SBS test was performed using universal testing machine until failure, and failure modes were visually analyzed. Translucency parameter and curing-light transmission values through 1, 2, and 3 mm thickness were quantified using spectrophotometry and the MARC resin calibrator, respectively. Scanning electron microscopy (SEM) was used to examine the CAD/CAM composites after surface treatment. Composite type and surface treatment had a significant effect on SBS. Laboratory composite showed the highest SBS value (22.4 MPa). Cerasmart 270 exhibited higher translucency parameter values (19.8, 11.0, 5.0) than SFRC (14.5, 5.2, 1.6) at the three composite thicknesses tested. Air-particle abrasion was more effective in enhancing SBS than acid etching. Experimental SFRC CAD/CAM composite showed higher SBS values than Cerasmart 270. For all composites, translucency parameter values and light transmission decreased as thickness increased.

The effect of different storage media on the monomer elution and hardness of CAD/CAM composite blocks

OBJECTIVE

This study aimed to assess the effect of different storage media on the hardness and monomer elution of CAD/CAM composite blocks.

METHODS

Five resin-composite blocks (RCB), one polymer-infiltrated ceramic network (PICN) block (Enamic (EN)), one ceramic-filled poly ether ether ketone (PEEK) block (Dentokeep (DK)), and one feldspathic ceramic block. Microhardness was measured using a Vickers indenter tester (FM-700, Future Tech Corp., Japan). In addition 4 conventional resin-composites were investigated for monomer elution using high performance liquid chromatography (HPLC) after storage in different media for 3 months. The data were analysed by three-way ANOVA, two-way ANOVA, one-way ANOVA, Tukey's post hoc test and the independent t-test (α=0.05 for all tests).

RESULTS

The specimens stored in the water had a hardness reduction ranging from 0.9% to 24.4%. In artificial saliva, the specimens had a hardness reduction ranging from 2.8% to 23.2%. The hardness reduction percentage in 75% Ethanol/Water (E/W) ranged between 3.8% and 35.3%. All materials, except GR (resin-composite block) and DK (Polyetheretherketone (PEEK)), showed a variable extent of monomer elution into 75% E/W with significantly higher amounts eluted from conventional composites. GRA and GND (conventional resin-composites) eluted TEGDMA in artificial saliva and GRA eluted TEGDMA in water.

SIGNIFICANCE

The hardness of CAD/CAM composite blocks was affected by different storage media, and they were not as stable as ceramic, with PICN exhibited superior hardness stability to all of the resin-composite blocks in all the storage media and was comparable to ceramic block. The hardness reduction percentage of the CAD/CAM composite blocks was influenced by the filler loading and resin-matrix composition.Minimal or no monomer elution from CAD/CAM blocks was detected.

Characterisation of the Filler Fraction in CAD/CAM Resin-Based Composites

The performance of dental resin-based composites (RBCs) heavily depends on the characteristic properties of the individual filler fraction. As specific information regarding the properties of the filler fraction is often missing, the current study aims to characterize the filler fractions of several contemporary computer-aided design/computer-aided manufacturing (CAD/CAM) RBCs from a material science point of view. The filler fractions of seven commercially available CAD/CAM RBCs featuring different translucency variants were analysed using Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), Micro-X-ray Computed Tomography (µXCT), Thermogravimetric Analysis (TG) and X-ray Diffractometry (XRD). All CAD/CAM RBCs investigated included midifill hybrid type filler fractions, and the size of the individual particles was clearly larger than the individual specifications of the manufacturer. The fillers in Shofu Block HC featured a sphericity of ≈0.8, while it was <0.7 in all other RBCs. All RBCs featured only X-ray amorphous phases. However, in Lava Ultimate, zircon crystals with low crystallinity were detected. In some CAD/CAM RBCs, inhomogeneities (X-ray opaque fillers or pores) with a size <80 µm were identified, but the effects were minor in relation to the total volume (<0.01 vol.%). The characteristic parameters of the filler fraction in RBCs are essential for the interpretation of the individual material's mechanical and optical properties.

Frequency-related viscoelastic properties in high translucent CAD-CAM resin-based composites

OBJECTIVE

The study aims to quantify the viscoelastic properties of representative dental CAD/CAM resin-based composites (RBC) and to determine the effects of loading frequencies on the viscoelastic material response in comparison to clinically established CAD/CAM glass ceramics.

METHODS

Eight RBCs, one leucite-reinforced, and one lithium disilicate glass-ceramics were selected. The quasi-static (indentation hardness H_IT, indentation modulus, E_IT) and viscoelastic (storage modulus E', loss modulus E″, loss factor tan δ) material behavior was monitored by a depth-sensing indentation test equipped with a DMA module. A low-magnitude oscillating force was therefore superimposed onto a quasi-static force (F_max = 1000 mN) at 20 different frequencies in the range 1-50 Hz. One and multiple-way analysis of variance (ANOVA), the Tukey honestly significant difference (HSD) post-hoc tests (α = 0.05), and a Pearson correlation analysis were used for data analysis.

RESULTS

The quasi-static parameters increased with the crystalline phase in glass ceramics and with the amount of inorganic filler in RBCs. The tan δ, which is related to the damping capacity of a material, increased with the increasing amount of glass phase in glass ceramics or with the amount of organic phase in RBCs. A pronounced influence of the frequency on the measured parameters and their patterns of variation was observed. H_IT was up to ten time higher in glass ceramics compared to RBCs and highest at the lowest frequency (1 Hz). Parameters E_IT and E' differ less and were lowest at the lowest frequency. E″ distinguished three different patterns of variation with frequency. The tan δ decreased rapidly with frequency in glass ceramics, while the decrease in RBCs was gradually. Frequency influenced stronger tan δ (p < 0.001, η_P² = 0.85), followed by E' (p < 0.001, η_P² = 0.773), E_IT (p < 0.001, η_P² = 0.772), and E″ (p < 0.001, η_P² = 0.714), and less H_IT (p < 0.001, η_P² = 0.384).

CONCLUSIONS

All materials sowed viscoelastic behavior related to their microstructure and the internal friction created by grain or interphase boundary relaxation. RBCs have better damping capabilities over a wider frequency range. The deviations from the ideal elasticity were significantly lower in the glass ceramics than in the RBCs.

New method to differentiate surface damping behavior and stress absorption capacities of common CAD/CAM restorative materials

OBJECTIVES

To assess energy dissipation capacities and surface damping abilities of different CAD/CAM restorative materials (CRMs) to characterize stress resistance during load peaks.

METHODS

Using instrumented indentation testing (IIT), Martens hardness (HM) together with its elastic (η_IT) and plastic index (η_ITdis) and Leeb hardness (HLD) together with its deduced energy dissipation (HLD_dis) were determined for eight ceramic, eight composite, and four polymer-based materials as well as three metals. The results were compared to those of bovine enamel. Ten indentations per material were performed at room temperature (23 ± 1 °C) on two separate specimens (12.0 × 12.0 × 3.5 mm³) after water storage (24 h; 37.0 ± 1.0 °C). Hardness parameters were recorded, and data were analyzed with one-way MANOVA (Games-Howell post hoc tests, α = 0.05). Correlations between different parameters were tested (Pearson, α = 0.05).

RESULTS

Independently determined HLD_dis, and η_ITdis values substantiated different energy dissipation characteristics of CRM, whereby a strong correlation was observed for the two datasets (r = 0.956, p = 0.011). Ceramics had the significantly lowest values (p < 0.001) while both parameters revealed the highest surface damping effects for metals (p < 0.001), followed in both cases by bovine enamel. Energy dissipation of polymer and composite CRM was in between ceramics and bovine enamel (p < 0.001), whereas only for HLD_dis did both show no significant difference (p > 0.05).

SIGNIFICANCE

Promising new HLD_dis and η_ITdis data allow a reliable differentiation of energy dissipation and surface damping capacities of CRMs. Previously published rankings of edge chipping and loss tangent results were perfectly reproduced, especially by HLD_dis.

Aging behavior of high-translucent CAD/CAM resin-based composite blocks

OBJECTIVE

The aim of this study was to investigate the influence of artificial aging on the mechanical properties and fracture patterns of novel CAD/CAM resin-based composite blocks (RCB).

METHODS

Flexural strength and modulus of RCBs from seven manufacturers (Voco, Grandio Blocs, GB; Ivoclar Vivadent, Tetric®CAD, TC; DMG, Luxacam Composite, LC; Shofu Block HC, SF; 3M, Lava™ Ultimate, LU; GC, Cerasmart®, CS; Coltene, BRILLIANT Crios, CB) were assessed in a three-point-bending test after an aging process consisting of three sequential steps (14 days storage in artificial saliva, 10,000 thermo-cycles in distilled water between 5/55 °C, 48 h storage in ethanol 75%). Fracture origins were determined in a fractographic examination using reflected light stereomicroscopy combined with transillumination and scanning electron microscopy. Effects of aging were statistically analysed using one-way ANOVA with Tukey's HSD post hoc test (α = 0.05) and Weibull statistics. Correlations regarding filler amount were analysed using linear regression analysis.

RESULTS

The strongest influence on the flexural modulus and strength was exerted based on the parameter material (p < 0.001, ɳ_P² = 0.957; ɳ_P² = 0.770), but the influence of in vitro aging was also significant (p < 0.001, ɳ_P² = 0.623; ɳ_P² = 0.407). Storage in artificial saliva decreased the flexural modulus and flexural strength of all materials, apart from CS, significantly (p < 0.05). The Weibull moduli varied from 5.8 to 22.4. Filler amount correlated significantly with flexural modulus (p < 0.001; R² = 0.739). Fractography revealed four different fracture patterns with fracture origins from the corner, edge or sub-surface and a smooth fracture surface with non-identifiable fracture origin. Specimens with smooth fracture surface showed the significantly lowest flexural strength (p < 0.001). Pores, agglomerates and inclusions were identified as fracture origins.

CONCLUSIONS

Storage in artificial saliva mainly reduced the mechanical properties significantly while additional thermal aging mostly maintained the results. Aging in ethanol mostly maintained the results for flexural modulus but led to an increase in flexural strength values to the level of the unaged specimens. Fractographic analysis revealed a significant accumulation of sub-surface fracture origins after storage in ethanol arising from inherent flaws.

Spatial Distribution of the Micro-Mechanical Properties in High-Translucent CAD/CAM Resin-Composite Blocks

Industrially cured, high-translucent computer-aided design/computer-aided manufacturing (CAD/CAM) resin-based composites (RBC) are the most recently launched dental restoratives. Clinical treatments and laboratory tests are based on a homogeneous distribution of properties within CAD/CAM blocks to obtain constant and reproducible results. The study therefore aims to determine the spatial distribution of various micro-mechanical parameters (Vickers hardness, Martens hardness, indentation modulus, creep, elastic and total indentation work) in five representative CAD/CAM RBCs. The properties of the tooth structure were evaluated under similar conditions. Filler size and shape were analyzed by scanning electron microscopy. A multivariate analysis (general linear model) identified a very strong influence of the material on all measured properties (p < 0.001; partial eta squared η_P² > 0.943), whereby the most sensitive parameters when identifying differences within regions were the indentation modulus and the elastic indentation work. CAD/CAM RBC blocks show gradually varying properties that can increase or decrease from central to peripheral areas regardless of the chemical composition of the materials or the inorganic filler fraction. The degree of variation in the measured properties is material-specific and less than 8.7%. Clinical applications and in vitro study designs should consider slight inhomogeneity in CAD/CAM RBC blocks, while the location of the regions with best mechanical performance depends on the material.

A Comparative Study of Light Transmission by Various Dental Restorative Materials and the Tooth Structure

CLINICAL RELEVANCE

Light transmission through dental materials and tooth structure has direct clinical implication on such factors as selecting an appropriate curing technique during a restorative process.

SUMMARY