Voltammetric determination of paracetamol, tramadol and caffeine using poly(Nile blue) modified glassy carbon electrode

Fe-Doped Red Fluorescent Carbon Dots for Caffeine Analysis in Energy Drinks Using a Paper-Based Sensor

This study introduces a highly sensitive and selective method for detecting caffeine in energy drinks by using red florescence iron and nitrogen co doped carbon dots (Fe-NCDs) as a florescent prob. The Fe-NCDs were synthesized by using an eco-friendly hydrothermal. Providing uniform, quasi-spherical nanoparticles. The photoluminescence properties of the Fe-NCDs exhibit strong red emission making them suitable for fluorescence-based sensing. A microfluidic paper analytical device (µPAD) was developed and coupled with a smartphone-based detection system to facilitate portable, low-cost caffeine quantification. The Fe-NCDs were embedded in the µPADs, enabling fluorescence enhancement upon interaction with caffeine. This enhancement was quantitatively analyzed using the smartphone camera and ImageJ software, revealing a strong linear correlation in the range of 1 to 40 µg/mL when both Gray Value (G.V) and Red-Green-Blue (RGB) of reaction analyzed by the software. The limit of detection (LOD) was of 0.024 µg/mL and 0.032 µg/mL respectively for both applied principles. The methods indicate remarkable selectivity for caffeine, and was validated through accurate recovery studies in commercial samples. This innovative method provides a powerful, cost-effective, and environmentally sustainable solution for on-site caffeine detection in energy drinks, offering significant potential for application in food safety and quality control.

A systematic review on electrochemical sensors for the detection of acetaminophen

Considerable progress has been made in the electrochemical determination of acetaminophen (AP) over the past few decades. Nanomaterials or enzymes as electrode modifiers greatly improve the performance of AP electrochemical sensors. This review focuses on the development potential, detection principles and techniques for the electrochemical analysis of AP. In particular, the design and construction of AP electrochemical sensors are discussed from the perspective of non-enzyme materials (such as nanomaterials, including precious metals, transition metals and non-metals) and enzyme substances (such as aryl acylamidase, polyphenol oxidase and horseradish peroxidase). Moreover, the influencing factors for AP electrochemical sensors and the simultaneous detection of AP and other targets are summarized, and the future prospective of AP electrochemical sensors is outlined. This review provides a reference and guidance for the development and application of electrochemical sensors for AP detection.

A disposable voltammetric sensor for the determination of diphenylamine using modified pencil graphite electrode

This study reports the electrochemical monitoring and sensing of diphenylamine (DPA), an anti-scald agent on a modified pencil graphite electrode (PGE). DPA is also a potentially toxic environmental pollutant. A polymer of tyrosine synthesized by electrochemical process was utilized for the determination of DPA in real samples. The electrodes were characterized using IR, SEM, EDAX, AFM and EIS analyses. As far as we know, this is first time reporting the utilization of modified PGE via green approach for the monitoring of DPA. A dynamic linear range of 1.00-117.11 µM with a lower detection limit (LOD) of 0.7050 µM was showed by this sensor for the electrochemical quantification of DPA. The electrochemical oxidation of DPA on the modified sensor followed a mixed adsorption -diffusion controlled kinetics. The sensor also showed good anti-interference property for the determination of DPA in real samples. Furthermore, the developed sensor was applied for the selective sensing of DPA from real apple extracts with good recovery. The real sample analysis was validated with standard spectrophotometric method.

Poly (safranine) modified carbon paste electrode as a sensor for the determination of fenitrothion pesticide

An effective electroanalytical method was developed for the quantitative evaluation of fenitrothion pesticide. The electrochemically modified carbon paste electrode CPE was constructed by applying a safranine layer on its surface. Safranine monomer is easily oxidized. So, a safranine layer was applied via electropolymerization using cyclic voltammetry in (2 × 10-5 M) safranine buffered solution with phosphate buffer BPS at pH.6, potential window (- 1.6: + 2 V), scan rate 100 mV/s. The morphology of the modified electrode was characterized using SEM images. The electropolymerization process was characterized by observing the gradual increases of the peak current with the subsequent scanning cycles. This modified CPE electrode showed an obvious sensitivity by cyclic voltammetry towards the cathodic peak of the fenitrothion nitro group at approximately - 0.73V with good sensitivity by enhancing it to be approximately 10 times more sensitive than on a bare carbon paste electrode CPE. The number of cycles was optimized for the electropolymerization process to be 12 cycles. Where, the peak current at - 0.73 V was gradually enhanced until 12 cycles when it is obviously decreased before slightly increasing again. The reproducibility of the modified electrode was ensured by repeating the sweep cycles using LSV for determining the fenitrothion at 5 µM where it was found that the peak current was unchanged for 10 sweeps before it starts to drop gradually. LSV voltammetry at previously optimized conditions of the potential window (- 0.4: - 1 V), sweep rate 100 mV/s, phosphate buffer at pH.6 was used for the quantitative studies. Where, the pHs of the determining medium were varied from pH 5.5 to pH 8 using phosphate buffer. It was observed that the most identified peak current was at pH.6 which is then decreased gradually until it completely disappeared at pH 8. The optimal accumulation time by adsorption of 140 s for the fenitrothion pesticide was confirmed in the range of (20 s-170 s). Where, the peak current was increased gradually with time up to 140 s then a plateau with a constant response was observed. The developed method showed an excellent linearity range of (1 μM:15 μM) with R2 parameter equal to 0.99906. LOD and LOQ were calculated to be 0.1 μM, and 0.34 μM respectively. Satisfactory levels have been reached for the calculated recovery, accuracy. Precision limits not exceed 1% for both repeatability and reproducibility measurements. F-value and t-value were measured for the suggested LSV method versus the standard HPLC method for the concentration of 8 μM fenitrothion and were found to be 1.482 and 0.123, respectively which didn't exceed the tabulated values. The ruggedness of the suggested method was examined toward deliberate safranine concentration variations in the concentration range of (0.01 mM-0.03 mM). Insignificant differences for the mean recovery at (98.33-98.93%) and precision at (1.39-2.6%) were observed. Hence, the reliability and validity of the developed LSV method were achieved and it was considered as rigid method.

CuONPs/MWCNTs/carbon paste modified electrode for determination of tramadol: theoretical and experimental investigation

A practical technique was applied to fabricate CuO nanostructures for use as the electrocatalyst. The green synthesis of cupric oxide nanoparticles (CuO NPs) via co-precipitation is described in this paper using an aqueous extract of Origanum majorana as both reductant and stabilizer, accompanied by characterization via XRD, SEM, and FTIR. The XRD pattern revealed no impurities, whereas SEM revealed low agglomerated spherical particles. CuO nanoparticles and multi wall carbon nanotubes (MWCNTs) have been used to create a modified carbon paste electrode. Voltammetric methods were used to analyze Tramadol using CuONPs/MWCNT as a working electrode. The produced nanocomposite showed high selectivity for Tramadol analysis with peak potentials of ~ 230 mV and ~ 700 mV and Excellent linear calibration curves for Tramadol ranging from 0.08 to 500.0 µM with a correlation coefficient of 0.9997 and detection limits of 0.025. Also, the CuO NPs/MWCNT/CPE sensor shows an an appreciable sensitivity of 0.0773 μA/μM to tramadol. For the first time the B3LYP/LanL2DZ, quantum method was used to compute DFT to determine nanocomposites' connected energy and bandgap energy. Eventually, CuO NPs/CNT was shown to be effective in detecting Tramadol in actual samples, with a recovery rate ranging from 96 to 104.3%.

A UiO-66-NH2 MOF/PAMAM Dendrimer Nanocomposite for Electrochemical Detection of Tramadol in the Presence of Acetaminophen in Pharmaceutical Formulations

In this work, we prepared a novel electrochemical sensor for the detection of tramadol based on a UiO-66-NH₂ metal-organic framework (UiO-66-NH₂ MOF)/third-generation poly(amidoamine) dendrimer (G3-PAMAM dendrimer) nanocomposite drop-cast onto a glassy carbon electrode (GCE) surface. After the synthesis of the nanocomposite, the functionalization of the UiO-66-NH₂ MOF by G3-PAMAM was confirmed by various techniques including X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), field emission-scanning electron microscopy (FE-SEM), and Fourier transform infrared (FT-IR) spectroscopy. The UiO-66-NH₂ MOF/PAMAM-modified GCE exhibited commendable electrocatalytic performance toward the tramadol oxidation owing to the integration of the UiO-66-NH₂ MOF with the PAMAM dendrimer. According to differential pulse voltammetry (DPV), it was possible to detect tramadol under optimized circumstances in a broad concentration range (0.5 μM-500.0 μM) and a narrow limit of detection (0.2 μM). In addition, the stability, repeatability, and reproducibility of the presented UiO-66-NH₂ MOF/PAMAM/GCE sensor were also studied. The sensor also possessed an acceptable catalytic behavior for the tramadol determination in the co-existence of acetaminophen, with the separated oxidation potential of ΔE = 410 mV. Finally, the UiO-66-NH₂ MOF/PAMAM-modified GCE exhibited satisfactory practical ability in pharmaceutical formulations (tramadol tablets and acetaminophen tablets).

A bibliometric analysis of graphene in acetaminophen detection: Current status, development, and future directions

Acetaminophen is a widely used analgesic throughout the world. Detection of acetaminophen has particular value in pharmacy and clinics. Electrochemical sensors assembled with advanced materials are an effective method for the rapid detection of acetaminophen. Graphene-based carbon nanomaterials have been extensively investigated for potential analytical applications in the last decade. In this article, we selected papers containing both graphene and acetaminophen. Bibliometrics was used to analyze the relationships and trends among these papers. The results show that the topic has grown at a high rate since 2009. Among them, the detection of acetaminophen by an electrochemical sensor based on graphene is the most important direction. Graphene has moved from being a primary sensing material to a substrate for immobilization of other active ingredients. In addition, the degradation of acetaminophen using graphene-modified electrodes is also an important direction. We analyzed the research history and current status of this topic through bibliometrics. Authors, institutions, countries, and key literature were discussed. We also proposed perspectives for this topic.

Advances of Drugs Electroanalysis Based on Direct Electrochemical Redox on Electrodes: A Review

The strong development of mankind is inseparable from the proper use of drugs, and the electroanalytical research of drugs occupies an important position in the field of analytical chemistry. This review mainly elaborates the research progress of drugs electroanalysis based on direct electrochemical redox on various electrodes for the recent decade from 2011 to 2021. At first, we summarize some frequently used electrochemical data processing and electrochemical mechanism research derivation methods in the literature. Then, according to the drug therapeutic and application/usage purposes, the research progress of drugs electrochemical analysis is classified and discussed, where we focus on drugs electrochemical reaction mechanism. At the same time, the comparisons of electrochemical sensing performance of the drugs on various electrodes from recent studies are listed, so that readers can more intuitively compare and understand the electroanalytical sensing performance of each modified electrode for each of the drug. Finally, this review discusses the shortcomings and prospects of the drugs electroanalysis based on direct electrochemical redox research.

PassStat, a simple but fast, precise and versatile open source potentiostat

This work presents 4 open source potentiostat solutions for performing accurate measurements in cyclic voltammetry and square wave voltammetry at a low price. A very simple and easy to reproduce analogic board (c.a. 10 €) was driven either by a Teensy card from the company PJRC under an Arduino/Python software solution (39 €) or by an Analog Discovery 2 device from Digilent (less than 300 €). A smartphone Bluetooth Android interface was also created to circumvent the use of a computer. We demonstrated that our scheme is suitable for measurements in classical electrochemical conditions but also to carry out experiments with ultramicroelectrodes. We could thus reach a noise resolution of less than 1 pA. Scan rates of 8000 Vs^-1 with ohmic drop compensation were also achieved. The device is suitable for teaching purposes but also for experiments in a participative science context on the ground, or countries with lower financial possibilities.

Development and Validation of an RP-HPLC-PDA Method for Determination of Paracetamol, Caffeine and Tramadol Hydrochloride in Pharmaceutical Formulations

Paracetamol (acetaminophen) (PAR), caffeine (CAF) and tramadol hydrochloride (TRA) are important drugs widely used for many clinical purposes. Determination of their contents is of the paramount interest. In this respect, a quick, simple and sensitive isocratic RP-HPLC method with photodiode array detection was developed for the determination of paracetamol, caffeine and tramadol in pharmaceutical formulations. An improved sensitive procedure was also evolved for tramadol using a fluorescence detector system. A C₁₈ column and a mobile phase constituted by methanol/phosphate were used. LODs were found to be 0.2 μg/mL, 0.1 μg/mL and 0.3 μg/mL for paracetamol, caffeine and tramadol hydrochloride, respectively, using photodiode-array detection. Alternatively, LOD for tramadol decreased to 0.1 μg/mL with the fluorescence detector. Other notable analytical figures of merit include the linear concentration ranges, 0.8–270 μg/mL, 0.4–250 μg/mL and 1.0–300 (0.2–40) μg/mL, for the same ordered analytes (including the fluorescence detector). The proposed method was successfully applied for the quantitative determination of the three drugs in tablet dosage forms.

Designed electrochemical sensor based on metallocene modified conducting polymer composite for effective determination of tramadol in real samples

A novel composite for the electrochemical sensing of tramadol (Tr) was developed by the inclusion of a metallocene mediator between two layers of conducting poly(3,4-ethylenedioxythiophene) (PEDOT) polymer, in the presence of sodium dodecyl sulfate (SDS), i.e., P/mediator/P⋯SDS. Three charge transfer mediators were evaluated: ferrocene carboxylic acid (FC1), ferrocene (FC2), and cobaltocene (CC) for Tr electrocatalytic oxidation. The FC1 charge mediator showed a relatively higher current response that was assisted by the electronic conduction of the polymer film. Moreover, SDS presented a great impact, resulting in the enhancement of the preconcentration and (or) accumulation of Tr ions at the interface, leading to faster electron transfer. In addition, the practical application of the proposed FC1 composite for the determination of Tr in real urine and serum samples was successfully achieved with adequate recovery results. Very low detection limits of 18.6 nM and 16 nM in the linear dynamic ranges of 7–300 µM and 5–280 µM, respectively, were obtained at the proposed sensor. Furthermore, the simultaneous determination of Tr with common interfering species, paracetamol (APAP), morphine (MO), dopamine (DA), ascorbic acid (AA) and uric acid (UA), proved excellent, with good resolution and large potential peaks separation. The excellent characteristics of the proposed composite such as high reproducibility, good sensitivity, selectivity, anti-interference ability, and good stability enhanced its application for determination of other narcotic drugs.

Green synthesis of silver nanoparticles using pollen extract: Characterization, assessment of their electrochemical and antioxidant activities

In the present study, a simple, cheaply and environmental friendly method was evaluated for the synthesis of silver nanoparticle via Cupressus sempervirens L. (CSPE) pollen extract as reducing and stabilizing agent. Various parameters such as volume of CSPE, temperature and reaction time on AgNPs formation were investigated spectrophotometrically to optimize reaction conditions. The electrochemical behavior of the biosynthesized AgNPs were investigated by cyclic voltammetry and square wave voltammetry techniques. An electrosensor based on AgNPs modified glassy carbon electrode were constructed and tested on electro reduction of hydrogen peroxide in phosphate buffer medium. The prepared electrosensor could detect the H₂O₂ in the range of 5.0 μM - 2.5 mM with a detection limit of 0.23 μM. In addition, the antioxidant activity of biosynthesized AgNPs were evaluated against DPPH free radical. Results obtained from the antioxidant study suggested that CSPE mediated AgNPs exhibit a good antioxidant effect.

Recent developments in voltammetric and amperometric sensors for cysteine detection

This review article aims to provide an overview of the recent advances in the voltammetric and amperometric sensing of cysteine (Cys). The introduction summarizes the important role of Cys as an essential amino acid, techniques for its sensing, and the utilization of electrochemical methods and chemically modified electrodes for its determination. The main section covers voltammetric and amperometric sensing of Cys based on glassy carbon electrodes, screen printed electrodes, and carbon paste electrodes, modified with various electrocatalytic materials. The conclusion section discusses the current challenges of Cys determination and the future perspectives.

Electrochemical Sensors Based on Conducting Polymers for the Aqueous Detection of Biologically Relevant Molecules

Electrochemical sensors appear as low-cost, rapid, easy to use, and in situ devices for determination of diverse analytes in a liquid solution. In that context, conducting polymers are much-explored sensor building materials because of their semiconductivity, structural versatility, multiple synthetic pathways, and stability in environmental conditions. In this state-of-the-art review, synthetic processes, morphological characterization, and nanostructure formation are analyzed for relevant literature about electrochemical sensors based on conducting polymers for the determination of molecules that (i) have a fundamental role in the human body function regulation, and (ii) are considered as water emergent pollutants. Special focus is put on the different types of micro- and nanostructures generated for the polymer itself or the combination with different materials in a composite, and how the rough morphology of the conducting polymers based electrochemical sensors affect their limit of detection. Polypyrroles, polyanilines, and polythiophenes appear as the most recurrent conducting polymers for the construction of electrochemical sensors. These conducting polymers are usually built starting from bifunctional precursor monomers resulting in linear and branched polymer structures; however, opportunities for sensitivity enhancement in electrochemical sensors have been recently reported by using conjugated microporous polymers synthesized from multifunctional monomers.

A novel nanostructured poly(thionine)-deep eutectic solvent/CuO nanoparticle film-modified disposable pencil graphite electrode for determination of acetaminophen in the presence of ascorbic acid

A new electrochemical sensor based on thionine (TH), an electroactive polymer, and CuO nanoparticle (CuONP)-modified pencil graphite electrode (PGE) has been developed. Poly(thionine) (PTH) was formed on the CuO/PGE surface by electropolymerisation in ethaline deep eutectic solvent (DES) containing acetic acid dopant to form PTH_Ethaline/CuO/PGE. Cyclic voltammetry, electrochemical impedance spectroscopy, and differential pulse voltammetry were utilized to evaluate the fabrication process, electrochemical properties, and performance parameters of the modified electrodes. The analytical performance of the PTH_Ethaline/CuO/PGE was evaluated with respect to linear range, limit of detection, repeatability, and reproducibility for the detection of acetaminophen (APAP) by electrooxidation in the presence of ascorbic acid (AA). Analytical parameters such as pH were optimized. The combined use of PTH and CuONP led to enhanced performance towards APAP due to the large electroactive surface area and synergistic catalytic effect, with a wide linear working range and low detection limit. The reliability of the proposed sensor for the detection of APAP was successfully tested in pharmaceutical samples containing APAP and AA, with very good recoveries. Graphical abstract.

A Screen-Printed Electrode Modified With Graphene/Co3O4 Nanocomposite for Electrochemical Detection of Tramadol

In this paper, graphene (Gr)/Co₃O₄ nanocomposite was synthesized and utilized for the development of a novel electrochemical sensor to detect tramadol. Tramadol determination was examined by linear sweep voltammetry, differential pulse voltammetry, cyclic voltammetry, and chronoamperometry on Gr/Co₃O₄ nanocomposite-modified screen-printed electrode (Gr/Co₃O₄/SPE) in phosphate-buffered saline (PBS). Under the optimized condition, the detection limit of tramadol is 0.03 μM (S/N = 3) in the linear ranges of 0.1–500.0 μM. Furthermore, Gr/Co₃O₄/SPE was satisfactorily utilized to detect tramadol in tramadol tablet and urine specimens.

Tramadol sensing in non-invasive biological fluids using a voltammetric electronic tongue and an electrochemical sensor based on biomimetic recognition

Tramadol (TRA) is a weak opioid analgesic, prescribed to relieve mild to moderately severe pain. However, side effects of TRA overdoses, including vomiting, depression, tachycardia, convulsions, morbidity and mortality are often reported. In this study, an electrochemical sensor based on molecularly imprinted conductive polymer was firstly developed for the quantitative and non-invasive detection of TRA. Secondly, a voltammetric electronic tongue (VE-Tongue) combined with chemometric methods was used for the qualitative analysis. The MIP sensor was constructed by self-assembling a poly-aniline layer coated with silver nanoparticles (PANI-AgNPs) on a screen-printed gold electrode (Au-SPE). Then, 2-amino-thiophenol was polymerised in the presence of TRA. The electronic device exhibits, under optimal conditions, responses proportional to TRA concentrations (0.01-100 µg/mL) with detection and quantification limits of 9.42 µg/mL and 28.55 µg/mL, respectively. Moreover, its selectivity was proven by insignificant interferences of substances (paracetamol and citric acid). Spiked saliva and urine samples were used for the sensor practical application with a significant recovery above 90% and standard deviations below 4.5%. Besides, urine samples' analyses using VE-Tongue and pattern recognition methods show good discrimination, classification, and prediction results with scores above 95%. Correspondingly, both electro-analytical devices could be viable for monitoring drugs in biological matrices.

Chemically modified carbon-based electrodes for the determination of paracetamol in drugs and biological samples

Paracetamol is a non-steroidal, anti-inflammatory drug widely used in pharmaceutical applications for its sturdy, antipyretic and analgesic action. However, an overdose of paracetamol can cause fulminant hepatic necrosis and other toxic effects. Thus, the development of advantageous analytical tools to detect and determine paracetamol is required. Due to simplicity, higher sensitivity and selectivity as well as costefficiency, electrochemical sensors were fully investigated in last decades. This review describes the advancements made in the development of electrochemical sensors for the paracetamol detection and quantification in pharmaceutical and biological samples. The progress made in electrochemical sensors for the selective detection of paracetamol in the last 10 years was examined, with a special focus on highly innovative features introduced by nanotechnology. As the literature is rather extensive, we tried to simplify this work by summarizing and grouping electrochemical sensors according to the by which manner their substrates were chemically modified and the analytical performances obtained.

Facile caffeine electrochemical detection via electrodeposited Ag nanoparticles with modifier polymers on carbon paste sensor at aqueous and micellar media

The analysis and detection of caffeine (Caf) is very useful due to its widespread usage in several daily consumed beverages, food products, and pharmacological preparations with various physiological effects. The preparation of a newly electrodeposited Ag nanoparticles – cellulose acetate phthalate (CAP) – chitosan (Chit) modified carbon paste (ACCMCP) sensor for sensitive determination of Caf in 0.01 mol L−1 H3PO4 solution (pH 1.0–5.0) both in aqueous and micellar media (0.5 mmol L−1 SDS) was achieved. The interaction of Caf was monitored using electrochemical techniques such as cyclic voltammetry, differential pulse voltammetry, electrochemical impedance spectroscopy, and chronoamperometry, and surface characterization was carried out using X-ray diffraction, scanning electron microscope, and energy dispersive X-ray techniques. The linear detection range of Caf was between 4 and 500 μmol L−1 (r2 = 0.955) and the limit of detection obtained from the calibration plot was 0.252 μmol L−1. The sensor was applicable for detecting Caf in numerous real samples with recoveries from 98.03% to 101.60% without interference of any accompanying species, which ensures high method selectivity.

Fluorescence Sensing of Caffeine in Tea Beverages with 3,5-diaminobenzoic Acid

A rapid, selective and sensitive method for the detection of caffeine in tea infusion and tea beverages are proposed by using 3,5-diaminobenzoic acid as a fluorescent probe. The 3,5-diaminobenzoic acid emits strong fluorescence around 410 nm under the excitation of light at 280 nm. Both the molecular electrostatic potential analysis and fluorescent lifetime measurement proved that the existence of caffeine can quench the fluorescence of 3,5-diaminobenzoic acid. Under the optimal experimental parameters, the 3,5-diaminobenzoic acid was used as a fluorescent probe to detect the caffeine aqueous solution. There exists a good linear relationship between the fluorescence quenching of the fluorescent probe and the concentration of caffeine in the range of 0.1–100 μM, with recovery within 96.0 to 106.2%, while the limit of detection of caffeine is 0.03 μM. This method shows a high selectivity for caffeine. The caffeine content in different tea infusions and tea beverages has been determined and compared with the results from HPLC measurement.

Voltammetric Techniques for the Analysis of Drugs using Nanomaterials based Chemically Modified Electrodes

Background:

Electroanalytical techniques play a very important role in the areas of medicinal, clinical as well as pharmaceutical research. Amongst these techniques, the voltammetric methods for the determination of drugs using nanomaterials based chemically modified electrodes (CMEs) have received enormous attention in recent years. This is due to the sensitivity and selectivity they provide on qualitative as well as quantitative aspects of the electroactive analyte under study. The aim of the present review was to discuss the work on nanomaterials based CMEs for the analysis of drugs covering the period from 2000 to present employing various voltammetric techniques for different classes of the drugs.

Methods:

The present review deals with the determination of different classes of drugs including analgesics, anthelmentic, anti-TB, cardiovascular, antipsychotics and anti-allergic, antibiotic and gastrointestinal drugs. Also, a special section is devoted for enantioanalysis of certain chiral drugs using voltammetry. The detailed information of the voltammetric determination for the drugs from each class employing various techniques such as differential pulse voltammetry, cyclic voltammetry, linear sweep voltammetry, square wave voltammetry, stripping voltammetry, etc. are presented in tabular form below the description of each class in the review.

Results:

Various nanomaterials including carbon nanotubes, graphene, carbon nanofibers, quantum dots, metal/metal oxide nanoparticles, polymer based nanocomposites have been used by researchers for the development of CMEs over a period of time. The large surface area to volume ratio, high conductivity, electrocatalytic activity and biocompatibility make them ideal modifiers where they produce synergistic effect which helps in trace level determination of pharmaceutical, biomedical and medicinal compounds. In addition, macrocyclic compounds as chiral selectors have been used for the determination of enantiomeric drugs where one of the isomers captured in the cavities of chiral selector shows stronger binding interaction for one of the enantiomorphs.

Conclusion:

arious kinds of functional nanocomposites have led to the manipulation of peak potential due to drug - nanoparticles interaction at the modified electrode surface. This has facilitated the simultaneous determination of drugs with almost similar peak potentials. Also, it leads to the enhancement in voltammetric response of the analytes. It is expected that such modified electrodes can be easily miniaturized and used as portable, wearable and user friendly devices. This will pave a way for in-vivo onsite real monitoring of single as well as multi component pharmaceutical compounds.