Nickel oxide/carbon nanotube nanocomposites prepared by atomic layer deposition for electrochemical sensing of hydroquinone and catechol

Electrochemical sensing platform using reduced graphene oxide and Sn MOF-derived hollow cubic composites for sensitive detection of catechol in environmental water samples

Catechol, a polyphenolic molecule and significant organic chemical intermediate, is a highly dangerous environmental contaminant due to its unpredictable nature and potential harm to both humans and the environment. This study presents the development of Sn MOF@rGO-650, identified as a hollow cube by SEM and TEM, created by carbonizing rGO on the surface of Sn MOF after in situ encapsulation. The Sn MOF@rGO-650 modified glassy carbon electrode was successfully constructed for the electrochemical detection of catechol. Under optimal conditions, the sensor exhibited a detection limit of 33 nM, a linear range of 0.20 μM-28 μM, and good long-term stability and reproducibility. This work proves for the first time that Sn MOF@rGO-650 composites can effectively detect catechol in real environmental water samples, achieving recoveries between 95.7 % and 104.8 %, and is validated in UV spectroscopy, which highlights its potential for practical applications.

Triangle-Shaped Cerium Tungstate Nanoparticles Used to Modify Carbon Paste Electrode for Sensitive Hydroquinone Detection in Water Samples

In this study, we propose an eco-friendly method for synthesizing cerium tungstate nanoparticles using hydrothermal techniques. We used scanning, transmission electron microscopy, and X-ray diffraction to analyze the morphology of the synthesized nanoparticles. The results showed that the synthesized nanoparticles were uniform and highly crystalline, with a particle size of about 50 nm. The electrocatalytic properties of the nanoparticles were then investigated using cyclic voltammetry and electrochemical impedance spectroscopy. We further used the synthesized nanoparticles to develop an electrochemical sensor based on a carbon paste electrode that can detect hydroquinone. By optimizing the differential pulse voltammetric method, a wide linearity range of 0.4 to 45 µM and a low detection limit of 0.06 µM were obtained. The developed sensor also expressed excellent repeatability (RSD up to 3.8%) and reproducibility (RSD below 5%). Interferences had an insignificant impact on the determination of analytes, making it possible to use this method for monitoring hydroquinone concentrations in tap water. This study introduces a new approach to the chemistry of materials and the environment and demonstrates that a careful selection of components can lead to new horizons in analytical chemistry.

One-Step Synthesis of Hollow CoS2 Spheres Derived from Polyoxometalate-Based Metal-Organic Frameworks with Peroxidase-like Activity

In this work, hollow CoS2 particles were prepared by a one-step sulfurization strategy using polyoxometalate-based metal-organic frameworks as the precursor. The morphology and structure of CoS2 have been monitored by scanning electron microscopy, X-ray photoelectron spectroscopy, and X-ray powder diffraction. The mechanism for the formation of CoS2 is discussed. The reaction time and sulfur content are found to be important factors that affect the morphology and pure phase formation of CoS2, and a hollow semioctahedral morphology of CoS2 with open voids was obtained when the sulfur source was twice as large as the precursor and the reaction time was 24 h. The CoS2 (24 h) particles show an excellent peroxidase-like activity for the oxidation of colorless 3,3',5,5'-tetramethylbenzidine (TMB) to blue oxidized (oxTMB) by hydrogen peroxide. The polyoxometalate used as a precursor helps to stabilize oxTMB during catalytic oxidation, forming a stable curve platform for at least 8 min. Additionally, the colorimetric detection of hydroquinone is developed with a low detection limit of 0.42 μM. This research provides a new strategy to design hollow materials with high peroxidase-mimicking activity.

Electrochemical detection and quantification of catechol based on a simple and sensitive poly(riboflavin) modified carbon nanotube paste electrode

In the present research work, selective and sensitive catechol (CT) detection and quantification were shown in the presence of resorcinol (RS) in 0.2 M phosphate buffer (PB) solution by preparing a low-cost, simple, and green carbon nanotube paste electrode (CNTPE) surface activated with electropolymerized riboflavin (PRF). The morphological, conductivity, and electrochemical features of the modified electrode (PRFMCNTPE) and bare carbon nanotube paste electrode (BCNTPE) materials were analyzed using electrochemical impedance spectroscopy (EIS), field emission scanning electron microscopy (FE-SEM), cyclic voltammetry (CV), and differential pulse voltammetry (DPV). The PRF-activated electrode displays outstanding sensitivity, stability, selectivity, reproducibility, and repeatability for the redox feature of CT with improved electrochemical current and declined electrochemical potential compared to BCNTPE. The peak currents of CT are correlated to the different CT concentrations (CV method: 6.0-60.0 μM & DPV method: 0.5-7.0 μM), and the obtained detection limit (DL) and quantification limit (QL) are found to be 0.025 μM and 0.085 μM (CV method) and 0.0039 μM and 0.0132 μM (DPV method), respectively. The prepared PRFMCNTPE material was advantageous for the examination of CT in environmentally important tap water sample as a real-time application.

Engineering MOFs derived metal oxide nanohybrids: Towards electrochemical sensing of catechol in tea samples

In this work, we have successfully developed Cu-MOF/CuO/NiO nanocomposites (NCs) and employed as a novel electrochemical sensing platform in catechol (CC) detection. The Scanning electron microscopy (SEM) along Energy dispersive X-ray Analysis (EDX), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) are carried out to characterize the as-fabricated Cu-MOF/CuO/NiO NCs. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques have used to obtain oxidation peak currents of CC. Glassy carbon electrode (GCE) modified with Cu-MOF/CuO/NiO has exposed the superb EC properties representing low limit of detection (LOD) of 0.0078 µM (S/N = 3). To assess the practicability of Cu-MOF/CuO/NiO based sensing medium, it has been used to detect CC from two varieties of tea, namely black and green. Thus, we anticipate that this structural integration strategy possesses encouraging application potential in sensing podium and material synthesis.

Influence of NiO ALD Coatings on the Field Emission Characteristic of CNT Arrays

The paper presents a study of a large-area field emitter based on a composite of vertically aligned carbon nanotubes covered with a continuous and conformal layer of nickel oxide by the atomic layer deposition method. The arrays of carbon nanotubes were grown by direct current plasma-enhanced chemical vapor deposition on a pure Si substrate using a nickel oxide catalyst which was also deposited by atomic layer deposition. The emission characteristics of an array of pure vertically oriented carbon nanotubes with a structure identical in morphology, covered with a layer of thin nickel oxide, are compared using the data from a unique computerized field emission projector. The deposition of an oxide coating favorably affected the emission current fluctuations, reducing them from 40% to 15% for a pristine carbon nanotube and carbon nanotube/nickel oxide, respectively. However, the 7.5 nm nickel oxide layer coating leads to an increase in the turn-on field from 6.2 to 9.7 V/µm.

Catechol sensor based on pristine and transition metal embedded holey graphyne: a first-principles density functional theory study

To develop a highly sensitive and selective biosensor for detecting noxious biomolecules from the environment, we examined catechol (Cc) adsorption in pristine and transition metal (TM = Sc, Cu, and Pd) embedded 2D holey graphyne (hGY) monolayers using the first-principles density functional theory method. The interaction between Cc and the pristine hGY is purely weak, and hence the response of the sensing device will be difficult to detect. Therefore, the TM doping strategy is adopted to improve the sensitivity. According to our findings, Sc binds strongly to the hGY monolayer, with a binding energy of -4.09 eV and a charge transfer of 1.89e from the valence orbitals of Sc to the C 2p orbitals. Later on, the Cc adsorption on the TM-embedded hGY was investigated. The interaction of Cc with the transition metal involves charge transfer from Cc to the metal d orbital. A large binding energy of -3.22 eV and a significant charge transfer of about 0.9e from the O 2p orbitals of Cc to the valence orbital of Sc suggest that the Sc embedded hGY monolayer is a good choice for the efficient sensing of Cc molecules. Furthermore, ab initio MD simulations confirmed the structural stability of the Sc + hGY system at room temperature. We strongly believe that this theoretical work will aid the experimentalists in designing and developing 2D semiconducting nanolayer-based biosensors for commercial purposes.

Cobalt Oxide Nanorod-Modified GCE as Sensitive Electrodes for Simultaneous Detection of Hydroquinone and Catechol

An electrochemical sensor based on a cobalt oxide nanorod (Co3O4NR) modified glassy carbon electrode (GCE) (Co3O4NR-GCE) was prepared for simultaneous and selective determination of hydroquinone (HQ) and catechol (CT). Surface morphology and crystallinity of Co3O4NR were investigated employing field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis. The structure (16 nm) of the Co3O4 nanorod was observed in the FESEM image. A sharp peak pattern in the XRD survey revealed the following crystal planes in Co3O4NR material: (111), (220), (311), (222), (400), (422), (511), and (440). Electrochemical characterization of modified Co3O4NR-GCE was carried out performing cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Selective and simultaneous detection of HQ and CT was carried out by performing CV and differential pulse voltammetry (DPV) analysis. In both studies, modified Co3O4NR-GCE showed well defined oxidation and reduction peaks for HQ and CT with enhanced peak current, and the oxidation peaks for HQ and CT were observed at 0.152 V and 0.254 V, respectively, in the CV analysis. Scan rate and pH variation analysis were performed to evaluate different kinetic parameters, including charge transfer coefficient (α = 0.56 for HQ and 0.66 for CT), heterogeneous charge transfer rate constant (ks = 56 for HQ and 72 for CT), and the number of electrons involved in HQ and CT oxidation. Quantitative analysis of HQ and CT was studied by observing the current response of DPV analysis with respect to concentration variation. Here, the detection limit was calculated as 0.2 µM for HQ with a linear concentration range of 5–200 µM, and 0.4 µM for CT with a linear concentration range of 5–150 µM. The practical applicability of the proposed sensor was investigated using sample solutions prepared in tap water. The reported sensor showed impressive selectivity towards HQ and CT in the presence of common interferents.

An experimental and theoretical approach to electrochemical sensing of environmentally hazardous dihydroxy benzene isomers at polysorbate modified carbon paste electrode

It is well known that, surfactants provide a neutral, positive and/or negative charge on the electrode surface by forming a monolayer, which in turn affects the charge transfer and redox potential during the electroanalysis process. However, the molecular level understanding of these surfactant-modified electrodes is worth investigating because the interaction of the analyte with the electrode surface is still unclear. In this report, we used quantum chemical models based on computational density functional theory (DFT) to investigate the polysorbate 80 structure as well as the locations of energy levels and electron transfer sites. Later, the bare carbon paste electrode (bare/CPE) was modified with polysorbate 80 and used to resolve the overlapped oxidation signals of dihydroxy benzene isomers. The m/n values obtained at polysorbate/CPE was approximately equal to 1, signifying the transfer of same number of protons and electrons. Moreover, the analytical applicability of the modified electrode for the determination of catechol (CC) and hydroquinone (HQ) in tap water samples gave an acceptable recovery result. Overall, the application of DFT to understand the molecular level interaction of modifiers for sensing applications laid a new foundation for fabricating electrochemical sensors.

Hybridized 1D-2D MnMoO4-MXene nanocomposites as high-performing electrochemical sensing platform for the sensitive detection of dihydroxybenzene isomers in wastewater samples

Hydroquinone (HQ) and catechol (CC) are the two major dihydroxybenzene isomers, are considered one of the toxic pollutants in wastewater, which often coexisted and impede each other during sample identification. For practical analysis and simultaneous detection of HQ and CC in wastewater, we fabricate a hybrid electrochemical sensor with electrospun one-dimensional (1D) MnMoO₄ nanofibers coupled with a few-layered exfoliated two-dimensional (2D) MXene. The facilitated abundant defective edges of 1D MnMoO₄ and 2D MXene nanoarchitecture accelerated the effect of synergistic signal amplification and exhibited high electrocatalytic activity towards the oxidation of hydroquinone and catechol. MnMoO₄-MXene-GCE showed oxidation potentials of 0.102 V and 0.203 V for hydroquinone and catechol, respectively. It revealed the distinguished and simultaneous detection range of 0.101 V with a strong anodic peak current. Noteworthily, the proposed 1D-2D hybridized MnMoO₄-MXene-GCE sensor exhibited a wide linear response from 5 nM to 65 nM for hydroquinone and catechol. Moreover, it showed a low detection limit of 0.26 nM and 0.30 nM for HQ and CC with high stability, respectively. The feasible 1D-2D MnMoO₄-MXene nanocomposite-based biosensor effectively detected hydroquinone and catechol in hazardous water pollutants using the differential pulse voltammetric technique with recovery values.

Picomolar level electrochemical detection of hydroquinone, catechol and resorcinol simultaneously using a MoS2 nano-flower decorated graphene

A Graphene-Molybdenum disulphide nanocomposite was developed for the simultaneous electrochemical detection of dihydroxy benzene isomers attributed to the structural aspects.

Barium titanate nanoparticle-based disposable sensor for nanomolar level detection of the haematotoxic pollutant quinol in aquatic systems

Barium titanate nanoparticles synthesized by a simple co-precipitation method and applied for the electrochemical detection of quinol.

Electrochemical sensor based on Ce-MOF/carbon nanotube composite for the simultaneous discrimination of hydroquinone and catechol

Ce-MOF/CNTs nanocomposites were prepared by a simple method and post-treated with NaOH/H₂O₂ mixed solution. The morphology and structure of the treated samples were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results show that the post treatment induces the Ce-MOF morphological changing from rod-like structure into particles, which are covered on the surface of CNTs. XPS demonstrates that there are two-valence (TV) of Ce³⁺/Ce⁴⁺ in the post-treated Ce-MOF/CNTs (TV) composite. The electrochemical behaviors of nanocomposite were also investigated on electrochemical work station. By utilization of the good electrical conductivity of CNT, the two-valence of Ce and the high surface area of MOF, the nanocomposites were used to fabricate the electrochemical sensor for the simultaneous electrochemical detection of hydroquinone (HQ) and catechol (CC). Compared to the Ce-MOF/CNTs/GCE, the post-treated Ce-MOF (TV)/CNTs/GCE exhibited two well-defined peaks for the electrochemical oxidation of HQ and CC. The linear ranges responding to HQ and CC are 10~100 μM and 5~50 μM respectively.

Coomassie brilliant blue G 250 modified carbon paste electrode sensor for the voltammetric detection of dihydroxybenzene isomers

In this present study, coomassie brilliant blue G-250 (CBBG) modified electrode was fabricated for the specific and simultaneous detection of three dihydroxybenzene isomers such as resorcinol (RS), catechol (CC) and hydroquinone (HQ). The fabrication of the modified electrode was carried out by electrochemical polymerization of CBBG on the surface of unmodified electrode. The surface structures of bare and fabricated electrode were studied by scanning electron microscope (SEM). The established electrode portrays the very fine interface with these isomers and displayed the sufficient sensitivity and selectivity. The specific parameters of pH solution, scan rate and varying the concentration of analytes were optimized at the modified electrode. The sensor process was originated to be adsorption-controlled activity and the low limit of detection (LOD) for RS and CC was attained at 0.24 and 0.21 µM respectively. In the simultaneous study, designed sensor clearly implies the three well separated anodic peaks for RS, HQ and CC nevertheless in unmodified electrode it failed. Also, the constructed electrode was applied for the real sample analysis in tap water and obtained results are agreeable and it consistent in-between 92.80–99.48%.

An efficient electrochemical sensing of hazardous catechol and hydroquinone at direct green 6 decorated carbon paste electrode

In this proposed work, direct green 6 (DG6) decorated carbon paste electrode (CPE) was fabricated for the efficient simultaneous and individual sensing of catechol (CA) and hydroquinone (HY). Electrochemical deeds of the CA and HY were carried out by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) at poly-DG6-modfied carbon paste electrode (Po-DG6-MCPE). Using scanning electron microscopy (SEM) studied the surface property of unmodified CPE (UCPE) and Po-DG6-MCPE. The decorated sensor displayed admirable electrocatalytic performance with fine stability, reproducibility, selectivity, low limit of detection (LLOD) for HY (0.11 μM) and CC (0.09 μM) and sensor process was originated to be adsorption-controlled phenomena. The Po-DG6-MCPE sensor exhibits well separated two peaks for HY and CA in CV and DPV analysis with potential difference of 0.098 V. Subsequently, the sensor was practically applied for the analysis in tap water and it consistent in-between for CA 93.25–100.16% and for HY 97.25–99.87% respectively.

Tuning Electrocatalytic Aptitude by Incorporating α-MnO2 Nanorods in Cu-MOF/rGO/CuO Hybrids: Electrochemical Sensing of Resorcinol for Practical Applications

In this study, Cu-MOF/rGO/CuO/α-MnO₂ nanocomposites have been fabricated by a one-step hydrothermal method and used in the voltammetric detection of resorcinol (RS). The poor conductivity of MOFs in the field of electrochemical sensing is still a major challenge. A series of Cu-MOF/rGO/CuO/α-MnO₂ nanocomposites have been synthesized with varying fractions of rGO and with a fixed amount of α-MnO₂ via a facile method. These nanocomposites are well characterized using some sophisticated characterization techniques. The as-prepared nanohybrids have strongly promoted the redox reactions at the electrode surface due to their synergistic effects of improved conductivity, high electrocatalytic activity, an enlarged specific surface area, and a plethora of nanoscale level interfacial collaborations. The electrode modified with Cu-MOF/rGO/CuO/α-MnO₂ has revealed superior electrochemical properties demonstrating linear differential pulse voltammetry (DPV) responses from a 0.2 to 22 μM RS concentration range (R² = 0.999). The overall results of this sensing podium have shown excellent stability, good recovery, and a low detection limit of 0.2 μM. With excellent sensing performance achieved, the practicability of the sensor has been evaluated to detect RS in commercial hair color samples as well as in tap water and river water samples. Therefore, we envision that our hybrid nanostructures synthesized by the structural integration strategy will open new horizons in material synthesis and biosensing platforms.

CNT/Al2O3 core-shell nanostructures for the electrochemical detection of dihydroxybenzene isomers

We report CNT/Al2O3 core-shell nanostructures for the electrochemical detection of dihydroxybenzene (DHB) isomers. Amorphous films of Al2O3 (1.2-15.4 nm in thickness) are uniformly deposited onto the inner and outer walls of CNTs by atomic layer deposition. The effect of the Al2O3 shell thickness on the electrochemical detection of dihydroxybenzene isomers was explored using cyclic and square-wave voltammetry. The best sensing properties are found at a shell thickness of approx. 2.4 nm (CNT/Al2O3(9) sensor), where the oxidation peak currents (sensor-signal) increased ca. 10 times as compared to a sensor fabricated with non-coated CNTs. All of the three DHB isomers (hydroquinone, catechol and resorcinol) are independently detected in the concentration ranges of 2-1000 μmol L-1, 0.5-700 μmol L-1 and 3.5-500 μmol L-1, respectively. The sensors show reliable repeatability, reproducibility, long-term stability, and applicability in the analysis of real samples. Based on these findings, a plausible mechanism is proposed highlighting the role of the Al2O3-shell.

Glassy Carbon Electrode Modified with C/Au Nanostructured Materials for Simultaneous Determination of Hydroquinone and Catechol in Water Matrices

The simultaneous determination of hydroquinone and catechol was conducted in aqueous and real samples by means of differential pulse voltammetry (DPV) using a glassy carbon electrode modified with Gold Nanoparticles (AuNP) and functionalized multiwalled carbon nanotubes by drop coating. A good response was obtained in the simultaneous determination of both isomers through standard addition to samples prepared with analytical grade water and multivariate calibration by partial least squares (PLS) in winery wastewater fortified with HQ and CT from 4.0 to 150.00 µM. A sensitivity of 0.154 µA µM−1 and 0.107 µA µM−1, and detection limits of 4.3 and 3.9 µM were found for hydroquinone and catechol, respectively. We verified the reliability of the developed method by simultaneously screening analytes in spiked tap water and industrial wastewater, achieving recoveries over 80%. In addition, this paper demonstrates the applicability of chemometric tools for the simultaneous quantification of both isomers in real matrices, obtaining prediction errors of lower than 10% in fortified wastewater.

Supramolecular assemblies of carbon nanocoils and tetraphenylporphyrin derivatives for sensing of catechol and hydroquinone in aqueous solution

Non-enzymatic electrochemical detection of catechol (CC) and hydroquinone (HQ), the xenobiotic pollutants, was carried out at the surface of novel carbon nanocoils/zinc-tetraphenylporphyrin (CNCs/Zn-TPP) nanocomposite supported on glassy carbon electrode. The synergistic effect of chemoresponsive activity of Zn-TPP and a large surface area and electron transfer ability of CNCs lead to efficient detection of CC and HQ. The nanocomposite was characterized by using FT-IR, UV/vis. spectrophotometer, SEM and energy dispersive X-ray spectroscopy (EDS). Cyclic voltammetry, differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy were used for the electrochemical studies. CNCs/Zn-TPP/GCE nanosensor displayed a limit of detection (LOD), limit of quantification (LOQ) and sensitivity for catechol as 0.9 µM, 3.1 µM and 0.48 µA µM-1 cm-2, respectively in a concentration range of 25-1500 µM. Similarly, a linear trend in the concentration of hydroquinone detection was observed between 25 and 1500 µM with an LOD, LOQ and sensitivity of 1.5 µM, 5.1 µM and 0.35 µA µM-1 cm-2, respectively. DPV of binary mixture pictured well resolved peaks with anodic peak potential difference, ∆Epa(CC-HQ), of 110 mV showing efficient sensing of CC and HQ. The developed nanosensor exhibits stability for up to 30 days, better selectivity and good repeatability for eight measurements (4.5% for CC and 5.4% for HQ).

Fabrication of an Extremely Cheap Poly(3,4-ethylenedioxythiophene) Modified Pencil Lead Electrode for Effective Hydroquinone Sensing

Hydroquinone (HQ) is one of the major deleterious metabolites of benzene in the human body, which has been implicated to cause various human diseases. In order to fabricate a feasible sensor for the accurate detection of HQ, we attempted to electrochemically modify a piece of common 2B pencil lead (PL) with the conductive poly(3,4-ethylenedioxythiophene) or PEDOT film to construct a PEDOT/PL electrode. We then examined the performance of PEDOT/PL in the detection of hydroquinone with different voltammetry methods. Our results have demonstrated that PEDOT film was able to dramatically enhance the electrochemical response of pencil lead electrode to hydroquinone and exhibited a good linear correlation between anodic peak current and the concentration of hydroquinone by either cyclic voltammetry or linear sweep voltammetry. The influences of PEDOT film thickness, sample pH, voltammetry scan rate, and possible chemical interferences on the measurement of hydroquinone have been discussed. The PEDOT film was further characterized by SEM with EDS and FTIR spectrum, as well as for stability with multiple measurements. Our results have demonstrated that the PEDOT modified PL electrode could be an attractive option to easily fabricate an economical sensor and provide an accurate and stable approach to monitoring various chemicals and biomolecules.