Integrated-electrochemical approaches powered by photovoltaic energy for detecting and treating paracetamol in water

Fabrication of Strontium Molybdate with Functionalized Carbon Nanotubes for Electrochemical Determination of Antipyretic Drug-Acetaminophen

In recent years, there has been a significant interest in the advancement of electrochemical sensing platforms to detect antipyretic drugs with high sensitivity and selectivity. The electrochemical determination of acetaminophen (PCT) was studied with strontium molybdate with a functionalized carbon nanotube (SrMoO4@f-CNF) nanocomposite. The SrMoO4@f-CNF nanocomposite was produced by a facial hydrothermal followed by sonochemical treatment, resulting in a significant enhancement in the PCT determination. The sonochemical process was applied to incorporate SrMoO4 nanoparticles over f-CNF, enabling a network-like structure. Moreover, the produced SrMoO4@f-CNF composite structural, morphological, and spectroscopic properties were confirmed with XRD, TEM, and XPS characterizations. The synergistic effect between SrMoO4 and f-CNF contributes to the lowering of the charge transfer resistance (Rct=85 Ω·cm2), a redox potential of Epc=0.15 V and Epa=0.30 V (vs. Ag/AgCl), and a significant limit of detection (1.2 nM) with a wide response range of 0.01-28.48 µM towards the PCT determination. The proposed SrMoO4@f-CNF sensor was studied with differential pulse voltammetry (DPV) and cyclic voltammetry (CV) techniques and demonstrated remarkable electrochemical properties with a good recovery range in real-sample analysis.

Photovoltaic Electrochemically Driven Degradation of Calcon Dye with Simultaneous Green Hydrogen Production

In this study, for the first time, the production of green hydrogen gas (H₂) in the cathodic compartment, in concomitance with the electrochemical oxidation (EO) of an aqueous solution containing Calcon dye at the anodic compartment, was studied in a PEM-type electrochemical cell driven by a photovoltaic (PV) energy source. EO of Calcon was carried out on a Nb/BDD anode at different current densities (7.5, 15 and 30 mA cm^-2), while a stainless steel (SS) cathode was used for green H₂ production. The results of the analysis by UV-vis spectroscopy and total organic carbon (TOC) clearly showed that the electrochemical oxidation (EO) of the Calcon dye after 180 min of electrolysis time by applying 30 mA cm^-2 reached up to 90% of degradation and 57% of TOC removal. Meanwhile, under these experimental conditions, a green H₂ production greater than 0.9 L was achieved, with a Faradaic efficiency of 98%. The hybrid electrolysis strategy is particularly attractive in the context of a circular economy, as these can be coupled with the use of more complex water matrices to transform organic depollution into an energy resource to produce H₂ as a chemical energy carrier.

Application of electro-Fenton and photoelectro-Fenton processes for the degradation of contaminants in landfill leachate

Worldwide, most solid waste ends its life in landfill sites, which have a significant environmental impact in several respects. In particular, rainfall over landfill sites results in the production of an aqueous leachate containing compounds having low biodegradability, high toxicity, and a high organic load. For this reason, this study aims to investigate the applicability of electro-Fenton (EF) and photoelectro-Fenton (PEF) processes as alternative for treating a local landfill effluent with high organic content (chemical oxygen demand (COD) = 2684.7 mg-O₂ L ^-1) in a continuous-flow reactor (using, for first time, this kind of system with higher electrodes area of 35 cm²) using boron-doped diamond anode (Nb/BDD) and a carbon felt cathode (FC) electrodes. The effects of current density j (30, 60 and 90 mA cm^-2) and UV radiation wavelength (UVA and UVC) were studied to evaluate the treatment efficiency as well as the energy consumption. Results clearly showed that, the best efficiencies removing organic matter, in terms of COD, were about 66%, 68% and 89% with an energy consumption of only 19.41, 17.61 and 17.59 kWh kg COD^-1 for EF, PEF-UVA and PEF-UVC respectively, at 90 mA cm^-2 after 4 h of operation. The treatment of this kind of effluent produced organic and inorganic by-products, the acetic and formic acids as well as NO₂^-, NO₃^-, and NH₄⁺, being assessed their concentrations.

Towards Development of Molecularly Imprinted Electrochemical Sensors for Food and Drug Safety: Progress and Trends

Due to their advantages of good flexibility, low cost, simple operations, and small equipment size, electrochemical sensors have been commonly employed in food safety. However, when they are applied to detect various food or drug samples, their stability and specificity can be greatly influenced by the complex matrix. By combining electrochemical sensors with molecular imprinting techniques (MIT), they will be endowed with new functions of specific recognition and separation, which make them powerful tools in analytical fields. MIT-based electrochemical sensors (MIECs) require preparing or modifying molecularly imprinted polymers (MIPs) on the electrode surface. In this review, we explored different MIECs regarding the design, working principle and functions. Additionally, the applications of MIECs in food and drug safety were discussed, as well as the challenges and prospects for developing new electrochemical methods. The strengths and weaknesses of MIECs including low stability and electrode fouling are discussed to indicate the research direction for future electrochemical sensors.

Achieving Electrochemical-Sustainable-Based Solutions for Monitoring and Treating Hydroxychloroquine in Real Water Matrix

Hydroxychloroquine (HCQ) has been extensively consumed due to the Coronavirus (COVID-19) pandemic. Therefore, it is increasingly found in different water matrices. For this reason, the concentration of HCQ in water should be monitored and the treatment of contaminated water matrices with HCQ is a key issue to overcome immediately. Thus, in this study, the development of technologies and smart water solutions to reach the Sustainable Development Goal 6 (SDG6) is the main objective. To do that, the integration of electrochemical technologies for their environmental application on HCQ detection, quantification and degradation was performed. Firstly, an electrochemical cork-graphite sensor was prepared to identify/quantify HCQ in river water matrices by differential pulse voltammetric (DPV) method. Subsequently, an HCQ-polluted river water sample was electrochemically treated with BDD electrode by applying 15, 30 and 45 mA cm−2. The HCQ decay and organic matter removal was monitored by DPV with composite sensor and chemical oxygen demand (COD) measurements, respectively. Results clearly confirmed that, on the one hand, the cork-graphite sensor exhibited good current response to quantify of HCQ in the river water matrix, with limit of detection and quantification of 1.46 mg L−1 (≈3.36 µM) and 4.42 mg L−1 (≈10.19 µM), respectively. On the other hand, the electrochemical oxidation (EO) efficiently removed HCQ from real river water sample using BDD electrodes. Complete HCQ removal was achieved at all applied current densities; whereas in terms of COD, significant removals (68%, 71% and 84% at 15, 30 and 45 mA cm−2, respectively) were achieved. Based on the achieved results, the offline integration of electrochemical SDG6 technologies in order to monitor and remove HCQ is an efficient and effective strategy.

Recent advances on modified reticulated vitreous carbon for water and wastewater treatment - A mini-review

Recently, modifications on reticulated vitreous carbon (RVC) have attracted attention as a promising strategy to produce low-cost, stable, and highly active electrodes leading to significant advances in the water/wastewater treatment field compared with raw RVC. Modified RVC materials have been used as cathode, anode, and membrane. Improvements on physical and electrocatalytic properties are achieved by RVC modification via diverse strategies, including the deposition of metal oxides, the introduction of surface functional groups, and the formation of composites, which were used to remove organic contaminants and pathogens from water matrices, as summarized in this mini-review. This mini-review mainly focused on papers published from 2015 to 2020 that reported modified RVC electrodes to eliminate pollutants and pathogens from water matrices by electrochemical advanced oxidation processes. Likewise, news challenges and opportunities are discussed, and perspectives for the ongoing and future studies in this research field are also given.

Green Composite Sensor for Monitoring Hydroxychloroquine in Different Water Matrix

Hydroxychloroquine (HCQ), a derivative of 4-aminoquinolone, is prescribed as an antimalarial prevention drug and to treat diseases such as rheumatoid arthritis, and systemic lupus erythematosus. Recently, Coronavirus (COVID-19) treatment was authorized by national and international medical organizations by chloroquine and hydroxychloroquine in certain hospitalized patients. However, it is considered as an unproven hypothesis for treating COVID-19 which even itself must be investigated. Consequently, the high risk of natural water contamination due to the large production and utilization of HCQ is a key issue to overcome urgently. In fact, in Brazil, the COVID-19 kit (hydroxychloroquine and/or ivermectin) has been indicated as pre-treatment, and consequently, several people have used these drugs, for longer periods, converting them in emerging water pollutants when these are excreted and released to aquatic environments. For this reason, the development of tools for monitoring HCQ concentration in water and the treatment of polluted effluents is needed to minimize its hazardous effects. Then, in this study, an electrochemical measuring device for its environmental application on HCQ control was developed. A raw cork–graphite electrochemical sensor was prepared and a simple differential pulse voltammetric (DPV) method was used for the quantitative determination of HCQ. Results indicated that the electrochemical device exhibited a clear current response, allowing one to quantify the analyte in the 5–65 µM range. The effectiveness of the electrochemical sensor was tested in different water matrices (in synthetic and real) and lower HCQ concentrations were detected. When comparing electrochemical determinations and spectrophotometric measurements, no significant differences were observed (mean accuracy 3.0%), highlighting the potential use of this sensor in different environmental applications.

Electrochemical Determination of Lead Using A Composite Sensor Obtained from Low-Cost Green Materials:Graphite/Cork

The purpose of this study was to develop an inexpensive, simple, and highly selective cork-modified carbon paste electrode for the determination of Pb(II) by differential pulse anodic stripping voltammetry (DPASV) and square-wave anodic stripping voltammetry (SWASV). Among the cork–graphite electrodes investigated, the one containing 70% w/w carbon showed the highest sensitivity for the determination of Pb(II) in aqueous solutions. Under SWASV conditions, its linear range and relative standard deviation are equal to 1–25 µM and 1.4%, respectively; the limit of detection complies with the value recommended by the World Health Organization. To optimize the operating conditions, the selectivity and accuracy of the analysis were further investigated by SWASV in acidic media. Finally, the electrode was successfully applied for the determination of Pb(II) in natural water samples, proving to be a sensitive electrochemical sensor that meets the stringent environmental control requirements.

Applicability of Cork as Novel Modifiers to Develop Electrochemical Sensor for Caffeine Determination

This study aims to investigate the applicability of a hybrid electrochemical sensor composed of cork and graphite (Gr) for detecting caffeine in aqueous solutions. Raw cork (RAC) and regranulated cork (RGC, obtained by thermal treatment of RAC with steam at 380 °C) were tested as modifiers. The results clearly showed that the cork-graphite sensors, GrRAC and GrRGC, exhibited a linear response over a wide range of caffeine concentration (5-1000 µM), with R² of 0.99 and 0.98, respectively. The limits of detection (LOD), estimated at 2.9 and 6.1 µM for GrRAC and GrRGC, suggest greater sensitivity and reproducibility than the unmodified conventional graphite sensor. The low-cost cork-graphite sensors were successfully applied in the determination of caffeine in soft drinks and pharmaceutical formulations, presenting well-defined current signals when analyzing real samples. When comparing electrochemical determinations and high performance liquid chromatography measurements, no significant differences were observed (mean accuracy 3.0%), highlighting the potential use of these sensors to determine caffeine in different samples.