Biodegradable kinetics and behavior of bio-based polyblends under simulated aerobic composting conditions

Landfill-mined soil-like fraction (LMSF) use in biopolymer composting: Material pre-treatment, bioaugmentation and agricultural prospects

Polylactic Acid (PLA) based compostable bioplastic films degrade under thermophilic composting conditions. The purpose of our study was to understand whether sample pre-treatment along with bioaugmentation of the degradation matrix could reduce the biodegradation time under a simulated composting environment. Sepcifically, we also explored whether the commercial composts could be replaced by landfill-mined soil-like fraction (LMSF) for the said application. The effect of pre-treatment on the material was analysed by tests like tensile strength analysis, hydrophobicity analysis, morphological analysis, thermal degradation profiling, etc. Subsequently, the degradation experiment was performed in a simulated composting environment following the ASTM D5338 standard, along with bioaugmentation in selected experimental setups. When the novel approach of material pre-treatment and bioaugmentation were applied in combination, the time necessary for 90% degradation was reduced by 27% using compost and by 23% using LMSF. Beyond the improvement in degradation rate, the water holding capacity increased significantly for the degradation matrices. With pH, C: N ratio and microbial diversity tested to be favourable through 16s metabarcoding studies, material pre-treatment and bioaugmentation allow LMSF to not only replace commercial compost in polymer degradation but also find immense application in the agricultural sector of drought-affected areas (for better water retention) after it has been used for PLA degradation.

Deterioration of bio-based polylactic acid plastic teabags under environmental conditions and their associated effects on earthworms

In response to the plastic waste crisis, teabag producers have substituted the petrochemical-plastic content of their products with bio-based, biodegradable polymers such as polylactic acid (PLA). Despite widespread use, the degradation rate of PLA/PLA-blended materials in natural soil and their effects on soil biota are poorly understood. This study examined the percentage mass deterioration of teabags with differing cellulose:PLA compositions following burial (-10 cm depth) in an arable field margin for 7-months, using a suite of analytical techniques, such as size exclusion chromatography, 1H nuclear magnetic resonance, dynamic scanning calorimetry, and scanning electron microscopy. The effect of 28-d exposure to teabag discs at environmentally relevant concentrations (0.02 %, 0.04 % and 0.07 % w/w) on the survival, growth and reproduction (OECD TG 222 protocol) of the key soil detritivore Eisenia fetida was assessed in laboratory trials. After 7-month burial, Tbag-A (2.4:1 blend) and Tbag-B (3.5:1 cellulose:PLA blend) lost 66 ± 5 % and 78 ± 4 % of their total mass, primarily attributed to degradation of cellulose as identified by FTIR spectroscopy and a reduction in the cellulose:PLA mass ratio, while Tbag-C (PLA) remained unchanged. There were clear treatment and dose-specific effects on the growth and reproductive output of E. fetida. At 0.07 % w/w of Tbag-A adult mortality marginally increased (15 %) and both the quantity of egg cocoons and the average mass of juveniles also increased, while at concentrations ≥0.04 % w/w of Tbag-C, the quantity of cocoons was suppressed. Adverse effects are comparable to those reported for non-biodegradable petrochemical-based plastic, demonstrating that bio-based PLA does not offer a more 'environmentally friendly' alternative. Our study emphasises the necessity to better understand the environmental fate and ecotoxicity of PLA/PLA-blends to ensure interventions developed through the UN Plastic Pollution Treaty to use alternatives and substitutes to conventional plastics do not result in unintended negative consequences.

Alternative end-of-life options for disposable bioplastic products: Degradation and ecotoxicity assessment in compost and soil

Four different end-of-life options for disposable bioplastic cups were investigated and compared based on their environmental implications. Two products with distinct polymeric composition were tested simulating the following scenarios at laboratory scale: i) industrial composting (180 days at 58 °C); ii) anaerobic digestion followed by industrial composting (45 days at 55 °C and 180 days at 58 °C); iii) anaerobic digestion followed by direct digestate use on soil for agricultural purposes (45 days at 55 °C and 180 days at 25 °C); iv) uncontrolled release into a soil environment (180 days at 25 °C). Ecotoxicity tests were run at the end of each experiment to investigate the effects of the materials on three main groups of terrestrial model organisms: plants, earthworms and nitrifying bacteria. Complete biodegradation of the cups was observed in 180 days in the scenarios involving composting environment. A low degree of biodegradation (22.9 ± 4.5%) of the digestates in soil was observed, warning for a potential micro-bioplastics discharge into the environment. No degradation was observed for the cups in soil during the same testing period. Ecotoxicity tests revealed a negative effect on plants biomass growth across all samples, which was 17-30% lower compared to the blank sample. The experimental campaign highlighted the need for a systematic assessment of controlled treatment of bioplastics, as well as the need for a harmonized legislative framework.

The Mechanical Properties and Degradation Behavior of 3D-Printed Cellulose Nanofiber/Polylactic Acid Composites

Polylactic acid (PLA) has been widely used in many fields because of its good biodegradability, biocompatibility, and renewability. This work studied the degradation behavior and mechanical properties of cellulose nanofiber (CNF)/PLA composites. In vitro degradation experiments of 3D-printed samples were conducted at elevated temperatures, and the degradation characteristics were evaluated by mechanical tests, gel permeation chromatography (GPC), differential scanning calorimetric (DSC), and scanning electron microscope (SEM). The results indicated that the addition of CNF (0.5 wt%) accelerated the degradation rate of PLA. The decreases in number average molecular weight (Mn) and weight average molecular weight (Mw) of composites were 7.96% and 4.91% higher than that of neat PLA, respectively. Furthermore, the tensile modulus of composites was 18.4% higher than that of neat PLA, while the strength was 7.4% lower due to poor interfacial bonding between CNF and PLA. A mapping relationship between accelerated and normal degradation showed that the degradation experienced during 60 days at 37 °C was equivalent to that undergone during 14 days at 50 °C; this was achieved by examining the alteration in Mn. Moreover, the degradation process caused a notable deformation in the samples due to residual stress generated during the 3D printing process. This study provided valuable insights for investigating the in vitro degradation behavior of 3D-printed products.

Assessing the Effect of Cellulose Nanocrystal Content on the Biodegradation Kinetics of Multiscale Polylactic Acid Composites under Controlled Thermophilic Composting Conditions

This work studied the effect of cellulose nanocrystal (NCC) content on the biodegradation kinetics of PLA-based multiscale cellulosic biocomposites (PLAMCBs). To facilitate biodegradation, the materials were subjected to thermo-oxidation before composting. Biodegradation was carried out for 180 days under controlled thermophilic composting conditions according to the ASTM D 5338 standard. A first-order model based on Monod's kinetics under limiting substrate conditions was used to study the effect of cellulose nanocrystal (NCC) content on the biodegradation kinetics of multiscale composite materials. It was found that thermo-oxidation at 70 °C for 160 h increased the biodegradability of PLA. Also, it was found that the incorporation of cellulosic fibrous reinforcements increased the biodegradability of PLA by promoting hydrolysis during the first stage of composting. Likewise, it was found that partial substitution of micro cellulose (MFC) by cellulose nanocrystals (NCCs) increased the biodegradability of the biocomposite. This increase was more evident as the NCC content increased, which was attributed to the fact that the incorporation of cellulose nanocrystals facilitated the entry of water into the material and therefore promoted the hydrolytic degradation of the most recalcitrant fraction of PLA from the bulk and not only by surface erosion.

The development of recycling methods for bio-based materials - A challenge in the implementation of a circular economy: A review

This review focuses on the characteristics of the most widely used biopolymers that contain starch, polylactic acid, cellulose and/or polybutylene succinate. Because worldwide production of bio-based materials has grown dynamically, their waste is increasingly found in the existing waste treatment plants. The development of recycling methods for bio-based materials remains a challenge in the implementation of a circular economy. This article summarizes the recycling methods for bio-based materials, which, in the hierarchy of waste management, is much more desirable than landfilling. Several methods of recycling are available for the end-of-life management of bio-based products, which include mechanical (reuse of waste as a valuable raw material for further processing), chemical (feedstock recycling) and organic (anaerobic digestion or composting) ones. The use of chemical or mechanical recycling is less favourable, more costly and requires the improvement of systems for separation of bio-based materials from the rest of the waste stream. Organic recycling can be a sustainable alternative to those two methods. In organic recycling, bio-based materials can be biologically treated under aerobic or anaerobic conditions, depending on the characteristics of the materials. The choice of the recycling method to be implemented depends on the economic situation and on the properties of the bio-based products and their susceptibility to degradation. Thus, it is necessary to label the products to indicate which method of recycling is most appropriate.

Effects of Modified Thermoplastic Starch on Crystallization Kinetics and Barrier Properties of PLA

This study reports on using reactive extrusion (REX) modified thermoplastic starch particles as a bio-based and biodegradable nucleating agent to increase the rate of crystallization, percent crystallinity and improve oxygen barrier properties while maintaining the biodegradability of PLA. Reactive blends of maleated thermoplastic starch (MTPS) and PLA were prepared using a ZSK-30 twin-screw extruder; 80% glycerol was grafted on the starch during the preparation of MTPS as determined by soxhlet extraction with acetone. The crystallinity of PLA was found to increase from 7.7% to 28.6% with 5% MTPS. The crystallization temperature of PLA reduced from 113 °C to 103 °C. Avrami analysis of the blends showed that the crystallization rate increased 98-fold and t_1/2 was reduced drastically from 20 min to <1 min with the addition of 5% MTPS compared to neat PLA. Observation from POM confirmed that the presence of MTPS in the PLA matrix significantly increased the rate of formation and density of spherulites. Oxygen and water vapor permeabilities of the solvent-casted PLA/MTPS films were reduced by 33 and 19% respectively over neat PLA without causing any detrimental impacts on the mechanical properties (α = 0.05). The addition of MTPS to PLA did not impact the biodegradation of PLA in an aqueous environment.

Functionalized poly(lactic acid) based nano-fabric for anti-viral applications

This study endeavoured to explore and fabricate antiviral and antibacterial facemasks using zinc (oligo-lactate) (ZL), developed through a microwave synthesis technique. The prepared nano-fabric layer has excellent antiviral and antibacterial properties against Newcastle Disease Virus (NDV) and E. coli and S. aureus, respectively. Thermogravimetric analysis (TGA) of ZL shows a two-step thermal degradation, which confirms the formation of low molecular weight end group lactyl units with zinc ions. Another investigation using varying ZL concentration and silk nanocrystal (SNC) with poly(lactic acid) (PLA) and electrospinning them into nanofibres led to the fabrication of a facile and sustainable nanofabric that can be utilized as a protective layer for facemasks. Morphological analysis revealed the successful preparation of the nanofabric with proper distribution and uniformity in fibre diameter. Hydrophobicity of the prepared nanofabric confirmed excellent protection from water droplets that may transpire during coughing or sneezing by an infected individual. Breathability and reusability tests confirmed that the prepared facemask could be reused by ethanol washing without compromising its surface properties till 4 cycles. The PLA/ZL nanofabric layer demonstrated 97% antiviral efficacy against NDV in 10 minutes. In conclusion, the electrospun nanofabric layer can be used as a facemask having high hydrophobicity, good breathability, antibacterial, and antiviral properties to control the spread of contagious diseases.

The role of waste management in reducing bioplastics' leakage into the environment: A review

Bioplastics are becoming more and more widespread as substitutes for petroleum-derived plastics due to their biodegradability. Bioplastics degradation under different environments has been described and reported to depend mainly on bioplastics' compositions and the environmental conditions. Incomplete degradation during waste management processes and leakage of bioplastics into the environment are becoming major concerns that need to be further investigated. In this context, the present paper aimed to review recent literature dealing with biodegradation of bioplastics under industrial (e.g. anaerobic digestion and composting) and natural (e.g. soil and water) environments, and to link it to the potential bioplastics' leakage into the environment. Reviewed data were used to estimate the potential role of waste management processes in decreasing the potential leakage of bioplastics. Depending on bioplastics' type and processing conditions, waste management can effectively reduce bioplastics' potential leakage, decreasing the concentration of these materials that can reach the natural environments.

Degradation of bioplastics in organic waste by mesophilic anaerobic digestion, composting and soil incubation

The aim of the study was to assess the effects of high concentrations (10 % w/w, data projected for 2030) of commercial bioplastics, i.e. starch based shopping bags (SBSB) and polylactic acid (PLA) tableware, in the organic fraction of municipal solid wastes (MSW) on compost quality obtained by pilot-scale dry mesophilic anaerobic digestion and subsequent composting of the digestate. After the biological processes, 48.1 % total solids (TS) of SBSB and 15 % TS of PLA degraded, resulting in a high bioplastics content (about 18 % TS) in compost. Subsequent compost incubation in soils indicated that bioplastics degraded by pseudo-zero order kinetics (0.014 and 0.010 mg C cm^-2 d^-1 for SBSB and PLA, respectively), i.e. complete degradation was expected in 1.6 years (SBSB) and 7.2 years (PLA), confirming the intrinsic biodegradability of bioplastics. Nevertheless, enhancing the rate and amount of bioplastics degradation during waste management represents a goal to decrease the amount of bioplastics reaching the environment.

Biodegradation kinetic modeling of pro-oxidant filled polypropylene composites under thermophilic composting conditions after abiotic treatment

This work aims at modeling and characterizing the kinetics of biodegradation of polypropylene loaded with cobalt stearate as pro-oxidant after abiotic treatment. Eight films of these composites were prepared using different pro-oxidant loadings. These films were treated abiotically using accelerated weathering for 40 h, and biotically using aerobic composting as per ASTM D 5338. The experimental data were analyzed using an eight-parameter Komilis model containing a flat lag phase. The model formulations involved hydrolysis of primary solid carbon and its subsequent mineralization. The first step was rate controlling and it included hydrolysis of slowly (Cs), moderately (Cm), and readily (Cr) hydrolyzable carbon fractions in parallel. The model parameters were evaluated by means of nonlinear regression technique. The surface morphology of the films before and after the biodegradability test supported the biodegradation results. The model parameters and undegraded/hydrolyzable/mineralizable carbon evolutions involved moderately and readily hydrolyzable carbons but with the absence of slowly hydrolyzable carbon. These exhibit degradability in the range of 11.20-36.42% in 45 days. Biodegradability increases with progressive increase in pro-oxidant loading. The rate of degradation reaches maximum (0.322-0.897% per day) at around the 39th-12th day. For all the films, readily hydrolyzable carbon fractions and their hydrolysis rate constants (kr) are appreciably increased with increasing pro-oxidant loading. All the films show the presence of growth phase because of their high initial readily hydrolyzable carbon fractions. The SEM images after the abiotic and subsequently biotic treatments were progressively rougher. The methods presented here can be used for the design and control of other similar systems.

Studying growth kinetics of microbial populations using information technology. Solving the Cauchy problem

The possibilities of information technologies in the study of growth dynamics and development of microbial populations have been shown. In the R programming language in the Jupyter Notebooks environment, a direct kinetic problem has been solved. Kinetic regularities of growth of microbial populations under periodic cultivation have been considered within the framework of an approximation based on numerical integration of velocity equations. The one-step Runge-Kutta method of the fourth order of accuracy has been used as a method for solving a differential equation with initial conditions (Cauchy problem). Initial conditions of the problem were: the number of time steps n=10,000; initial substrate concentration S0=1; the initial concentration of microorganisms has been considered in four variants: M0=0.01, M0=0.05, M0=0.1, M0=0.2, which correspond to 1%, 5%, 10%, 20% of the inoculum density accordingly; affinity ration of the substrate to microorganisms Ks=0.5. The use of modern information technologies in the analysis of microbial growth patterns is mainly determined by the capabilities of personal computers, software environments and shells. The potential of modern software in the implementation of applied engineering and research problems in solving ordinary differential equations describing the development and course of the microbial process over time has been presented.