Persistent organic pollutants: The trade-off between potential risks and sustainable remediation methods

Current advances of chlorinated organics degradation by bioelectrochemical systems: a review

Chlorinated organic compounds (COCs) are typical refractory organic compounds, having high biological toxicity. These compounds are a type of pervasive pollutants that can be present in polluted soil, air, and various types of waterways, such as groundwater, rivers, and lakes, posing a significant threat to the ecological environment and human health. Bioelectrochemical systems (BESs) are an effective strategy for the degradation of bio-refractory compounds. BESs improve the waste treatment efficiency through the application of weak electrical stimulation. This review discusses the processes of BESs configurations and degradation performances in different environmental media including wastewater, soil, waste gas and groundwater. In addition, the degradation mechanisms and performance-enhancing additives are summarized. The future challenges and perspectives on the development of BES for COCs removal are briefly discussed.

Innovative remediation strategies for persistent organic pollutants in soil and water: A comprehensive review

Persistent organic pollutants (POPs) provide a serious threat to human health and the environment in soil and water ecosystems. This thorough analysis explores creative remediation techniques meant to address POP pollution. Persistent organic pollutants are harmful substances that may withstand natural degradation processes and remain in the environment for long periods of time. Examples of these pollutants include dioxins, insecticides, and polychlorinated biphenyls (PCBs). Because of their extensive existence, cutting-edge and environmentally friendly eradication strategies must be investigated. The most recent advancements in POP clean-up technology for soil and water are evaluated critically in this article. It encompasses a wide range of techniques, such as nanotechnology, phytoremediation, enhanced oxidation processes, and bioremediation. The effectiveness, cost-effectiveness, and environmental sustainability of each method are assessed. Case studies from different parts of the world show the difficulties and effective uses of these novel techniques. The study also addresses new developments in POP regulation and monitoring, highlighting the need of all-encompassing approaches that include risk assessment and management. In order to combat POP pollution, the integration of diverse remediation strategies, hybrid approaches, and the function of natural attenuation are also examined. Researchers, legislators, and environmental professionals tackling the urgent problem of persistent organic pollutants (POPs) in soil and water should benefit greatly from this study, which offers a complete overview of the many approaches available for remediating POPs in soil and water.

Understanding and exploring the diversity of soil microorganisms in tea (Camellia sinensis) gardens: toward sustainable tea production

Leaves of Camellia sinensis plants are used to produce tea, one of the most consumed beverages worldwide, containing a wide variety of bioactive compounds that help to promote human health. Tea cultivation is economically important, and its sustainable production can have significant consequences in providing agricultural opportunities and lowering extreme poverty. Soil parameters are well known to affect the quality of the resultant leaves and consequently, the understanding of the diversity and functions of soil microorganisms in tea gardens will provide insight to harnessing soil microbial communities to improve tea yield and quality. Current analyses indicate that tea garden soils possess a rich composition of diverse microorganisms (bacteria and fungi) of which the bacterial Proteobacteria, Actinobacteria, Acidobacteria, Firmicutes and Chloroflexi and fungal Ascomycota, Basidiomycota, Glomeromycota are the prominent groups. When optimized, these microbes' function in keeping garden soil ecosystems balanced by acting on nutrient cycling processes, biofertilizers, biocontrol of pests and pathogens, and bioremediation of persistent organic chemicals. Here, we summarize research on the activities of (tea garden) soil microorganisms as biofertilizers, biological control agents and as bioremediators to improve soil health and consequently, tea yield and quality, focusing mainly on bacterial and fungal members. Recent advances in molecular techniques that characterize the diverse microorganisms in tea gardens are examined. In terms of viruses there is a paucity of information regarding any beneficial functions of soil viruses in tea gardens, although in some instances insect pathogenic viruses have been used to control tea pests. The potential of soil microorganisms is reported here, as well as recent techniques used to study microbial diversity and their genetic manipulation, aimed at improving the yield and quality of tea plants for sustainable production.

Removing polyfluoroalkyl substances (PFAS) from wastewater with mixed matrix membranes

Polyfluoroalkyl and perfluoroalkyl (PFAS) chemicals are fluorinated and exhibit complicated behavior. They are determined and highly resistant to ecological modifications that render plants ecologically robust. Thermal stability and water and oil resistance are examples of material qualities. Their adverse consequences are causing increasing worry due to their bioaccumulative nature in humans and other creatures. Direct data indicates that PFAS exposure in humans causes endocrine system disruption, immune system suppression, obesity, increased cholesterol, and cancer. Several PFASs are present in drinking water at low doses and may harm people. These cancer-causing PFAS have caused concern for water bodies all around the globe. Analytical techniques are used to identify and measure PFAS in an aqueous medium (membrane). Furthermore, a deeper explanation is provided for PFAS removal methods, including mixed matrix membrane (MMM) technology. By removing over 99 % of the PFAS from wastewater, MMMs may effectively remove PFAS from sewage when the support matrix contains adsorbing components. Furthermore, we consider several factors affecting the removal of PFAS and practical sorption methods for PFAS onto various adsorbents.

A critical review of sustainable pesticide remediation in contaminated sites: Research challenges and mechanistic insights

Incidental pesticide application on farmlands can result in contamination of off-target biota, soil, groundwater, and surrounding ecosystems. To manage these pesticide contaminations sustainably, it is important to utilize advanced approaches to pesticide decontamination. This review assesses various innovative strategies applied for remediating pesticide-contaminated sites, including physical, chemical, biological, and nanoremediation. Integrated remediation approaches appear to be more effective than singular technologies. Bioremediation and chemical remediation are considered suitable and sustainable strategies for decontaminating contaminated soils. Furthermore, this study highlights key mechanisms underlying advanced pesticide remediation that have not been systematically studied. The transformation of applied pesticides into metabolites through various biotic and chemical triggering factors is well documented. Ex-situ and in-situ technologies are the two main categories employed for pesticide remediation. However, when selecting a remediation technique, it is important to consider factors such as application sites, cost-effectiveness, and specific purpose. In this review, the sustainability of existing pesticide remediation strategies is thoroughly analyzed as a pioneering effort. Additionally, the study summarizes research uncertainties and technical challenges associated with different remediation approaches. Lastly, specific recommendations and policy advocacy are suggested to enhance contemporary remediation approaches for cleaning up pesticide-contaminated sites.

A Review: Subcritical Water Extraction of Organic Pollutants from Environmental Matrices

Most organic pollutants are serious environmental concerns globally due to their resistance to biological, chemical, and photolytic degradation. The vast array of uses of organic compounds in daily life causes a massive annual release of these substances into the air, water, and soil. Typical examples of these substances include pesticides, polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). Since they are persistent and hazardous in the environment, as well as bio-accumulative, sensitive and efficient extraction and detection techniques are required to estimate the level of pollution and assess the ecological consequences. A wide variety of extraction methods, including pressurized liquid extraction, microwave-assisted extraction, supercritical fluid extraction, and subcritical water extraction, have been recently used for the extraction of organic pollutants from the environment. However, subcritical water has proven to be the most effective approach for the extraction of a wide range of organic pollutants from the environment. In this review article, we provide a brief overview of the subcritical water extraction technique and its application to the extraction of PAHs, PCBs, pesticides, pharmaceuticals, and others form environmental matrices. Furthermore, we briefly discuss the influence of key extraction parameters, such as extraction time, pressure, and temperature, on extraction efficiency and recovery.

Role of Gastrointestinal Microbiota from Crucian Carp in Microbial Transformation and Estrogenicity Modification of Novel Plastic Additives

Ingestion is a major exposure route for hydrophobic organic pollutants in fish, but the microbial transformation and estrogenic modification of the novel plastic additives by the gut microbiota of fish remain obscure. Using an in vitro approach, we provide evidence that structure-related transformation of various plastic additives by the gastric and intestinal (GI) microbiota from crucian carp, with the degradation ratio of bisphenols and triphenyl phosphate faster than those of brominated compounds. The degradation kinetics for these pollutants could be limited by oxygen and cometabolic substrates (i.e., glucose). The fish GI microbiota could utilize the vast majority of carbon sources in a Biolog EcoPlate, suggesting their high metabolic potential and ability to transform various organic compounds. Unique microorganisms associated with transformation of the plastic additives including genera of Citrobacter, Klebsiella, and some unclassified genera in Enterobacteriaceae were identified by combining high-throughput genetic analyses and metagenomic analyses. Through identification of anaerobic transformation products by high-resolution mass spectrometry, alkyl-cleavage was found the common transformation mechanism, and hydrolysis was the major pathway for ester-containing pollutants. After anaerobic incubation, the estrogenic activities of triphenyl phosphate and bisphenols A, F, and AF declined, whereas that of bisphenol AP increased.

Data driven toxicity assessment of organic chemicals against Gammarus species using QSAR approach

Nowadays, organic chemicals play an essential role in almost all walks of life and have become indispensable to modern society. However, the continually synthesized chemicals and the numerous potential adverse endpoints against living organisms increasingly promote the regulators regarding the computational approach as a crucial supplement and an alternative to the traditional animal tests in chemical risk assessment. In this present research, we evaluated the ecotoxicity of chemicals against four typical Gammarus species, which constituted a critical element in detritus cycle and also the recommended species for water monitoring. We first screened the molecular descriptors based on the Genetic Algorithm and then developed the Quantitative Structure-Activity Relationship models using the Multiple Linear Regression method. The statistical results from various validation metrics suggested that the obtained models were internally robust and externally predictive. The application domain analysis based on the leverage approach and standardized residual method demonstrated the broad application range of each model. The interpretation of molecular descriptors in each model suggested that the chemicals with higher polarity and hydrophilicity tend to be less toxic, whereas the lipophilic moieties would enhance the chemical toxicity. Meanwhile, the other selected descriptors, such as Chi-cluster, heterocyclic, and distance matrix descriptors, manifested that the chemical toxicity was also affected by molecular branching, connectivity, electrotopological state, and other various properties. In summary, the present work proposed well-performed QSAR models and clarified the possible toxic mechanism of chemicals against Gammarus species. The obtained models could help predict the toxicity data and conduct a preliminary risk assessment, thus guiding the subsequent animal tests and reducing the assessment cost.

Role of Microbes in the degradation of organic semivolatile compounds in polar ecosystems: A review

The Arctic and the Antarctic Continent correspond to two eco-regions with extreme climatic conditions. These regions are exposed to the presence of contaminants resulting from human activity (local and global), which, in turn, represent a challenge for life forms in these environments. Anthropogenic pollution by semi-volatile organic compounds (SVOCs) in polar ecosystems has been documented since the 1960s. Currently, various studies have shown the presence of SVOCs and their bioaccumulation and biomagnification in the polar regions with negative effects on biodiversity and the ecosystem. Although the production and use of these compounds has been regulated, their persistence continues to threaten biodiversity and the ecosystem. Here, we summarize the current literature regarding microbes and SVOCs in polar regions and pose that bioremediation by native microorganisms is a feasible strategy to mitigate the presence of SVOCs. Our systematic review revealed that microbial communities in polar environments represent a wide reservoir of biodiversity adapted to extreme conditions, found both in terrestrial and aquatic environments, freely or in association with vegetation. Microorganisms adapted to these environments have the potential for biodegradation of SVOCs through a variety of genes encoding enzymes with the capacity to metabolize SVOCs. We suggest that a comprehensive approach at the molecular and ecological level is required to mitigate SVOCs presence in these regions. This is especially patent when considering that SVOCs degrade at slow rates and possess the ability to accumulate in polar ecosystems. The implications of SVOC degradation are relevant for the preservation of polar ecosystems with consequences at a global level.

TiO2 NPs-immobilized silica granules: New insight for nano catalyst fixation for hydrogen generation and sustained wastewater treatment

In heterogeneous catalytic processes, immobilization of the functional material over a proper support is a vital solution for reusing and/or avoiding a secondary pollution problem. The study introduces a novel approach for immobilizing R25 NPs on the surface of silica granules using hydrothermal treatment followed by calcination process. Due to the privileged characteristics of the subcritical water, during the hydrothermal treatment process, the utilized R25 NPs were partially dissolved and precipitated on the surface of the silica granules. Calcination at high temperature (700°C) resulted in improving the attachment forces. The structure of the newly proposed composite was approved by 2D and 3D optical microscope images, XRD and EDX analyses. The functionalized silica granules were used in the form of a packed bed for continuous removal of methylene blue dye. The results indicated that the TiO2:sand ratio has a considerable effect on the shape of the dye removal breakthrough curve as the exhaustion point, corresponding to ~ 95% removal, was 12.3, 17.4 and 21.3 min for 1:20, 1:10 and 1:5 metal oxides ratio, respectively. Furthermore, the modified silica granules could be exploited as a photocatalyst for hydrogen generation from sewage wastewaters under direct sunlight with a good rate; 75×10-3 mmol/s. Interestingly, after the ease separation of the used granules, the performance was not affected. Based on the obtained results, the 170°C is the optimum hydrothermal treatment temperature. Overall, the study opens a new avenue for immobilization of functional semiconductors on the surface of sand granules.

One-pot synthesis of graphene hydrogel/M (M: Cu, Co, Ni) nanocomposites as cathodes for electrochemical removal of rifampicin from polluted water

Nowadays, the removal of pharmaceutical contaminants from water resources and wastewater is of great importance due to environmental and health issues. Over the decades, various methods have been reported to remove pollutants from wastewater. Among the developed methods, advanced oxidation processes (AOPs) have received significant attention from researchers. In this study, we report the one-pot synthesis of graphene hydrogel-metal (GH-M, M: Co, Ni, Cu) nanocomposites via the combination of polyol and hydrothermal methods. The structure of the resulting nanocomposites was examined by transmission electron microscopy (TEM), inductively coupled plasma-mass spectroscopy (ICP-MS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and Raman spectroscopy methods. Afterward, as-prepared GH-Cu, GH-Co, and GH-Ni nanocomposites were used to prepare cathodes for the electro-Fenton (EF) process to remove rifampicin (RIF) from polluted water. The effect of operational parameters, including current density (mA/cm²), initial pH, initial RIF concentration (mg/L), and process time (min) was investigated via response surface methodology (RSM). The optimal values for current density, pH, initial RIF concentration, and process time using GH-Ni as cathode were 30 mA/cm², 5, 30 mg/L, and 90 min, respectively. The results at optimal values showed that the maximum RIF removal efficiency for GH-Cu, GH-Co, and GH-Ni cathodes was 90.47, 92.60, and 93.69%, respectively. Brunauer Emmett Teller (BET), atomic force microscopy (AFM), energy-dispersive X-ray (EDX), and cyclic voltammetry (CV) analyses were performed to investigate the performance of the cathodes for the RIF removal. Finally, total organic carbon (TOC), gas chromatography-mass spectrometry (GC-MS), and atomic absorption spectroscopy (AAS) analyses were performed for further investigation of the RIF removal from polluted water. The results claimed that one-pot synthesized GH-M cathodes can effectively remove RIF from polluted water through EF process.

Insights into the correlation between different adsorption/oxidation/catalytic performance and physiochemical characteristics of Fe-Mn oxide-based composites

Fe-Mn oxide-based composites have been widely used in the solidification of heavy metals or the removal of organic pollutants, which can not only show excellent adsorption/oxidation performance, but also show catalytic activity for common oxidants. At present, the correlation between adsorption/oxidation/catalytic performance and physicochemical characteristics of these composites, and the underlying mechanisms are still unclear. Therefore, the main purpose of this review is to disclose the internal relationship between the physicochemical properties of Fe-Mn oxide-based composites and the pollutant removal performance. From the perspective of crystal phase, the basic units of Fe-Mn oxide composites are divided into Fe-Mn binary oxide (FMBO) and spinel MnFe₂O₄, and the two species were discussed separately in most chapters. The selected physicochemical properties mainly include the type of Fe-Mn oxide composites, surface-to-volume ratio, pore volume, pH_pzc, crystal type, surface functional groups. Because the physicochemical properties that determine how effective Fe-Mn oxide material is at removing contaminants may differ as it performs different functions, we discussed the above problems under different application scenarios (adsorption, oxidation, and advanced oxidation process). Additionally, internal factor (Fe/Mn mole ratio) and external factors (pH_ini, co-ions and ionic strength) were analyzed, and several common synthetic strategies of these composites were presented.

In-silico study of reducing human health risk of POP residues' direct (from tea) or indirect exposure (from tea garden soil): Improved rhizosphere microbial degradation, toxicity control, and mechanism analysis

The accumulation of potentially harmful substances in tea garden soils and tea leaves, especially persistent organic pollutants (POPs), is a special concern for tea consumers worldwide. However, their potential health and ecological risks in tea gardens have rarely been investigated. This study proposed measures to improve the degradation ability of POPs by the tea rhizosphere and to reduce the human health risks caused by POPs after tea consumption. In this study, the binding energy values of six types of POPs and the degraded protein were used to reflect the degradation ability and calculated using molecular dynamic simulations. The main root secretions (i.e., catechin, glucose, arginine, and oxalic acid) were selected and applied with a combination of tea fertilizer and trace element combination (i.e., urea, straw, and copper element), leading to an improved degradation ability (49.59 %) of POPs. To investigate the mechanisms of the factors that affect the degradation ability, molecular docking, tensor singular value decomposition methods, multivariate correlation analysis and 2D-QSAR model were used. The results showed that the solvation energy and solvent accessible surface area are the main forces, and the molecular weight, boiling point, and topological radius of the POPs were the key molecular features affecting their degradation ability. Based on the three key characteristics, a diet avoidance scheme (i.e., avoiding lysine, maslinic acid, ethanol, perfluorocaproic acid, and cholesterol with tea), which can reduce the binding ability of POP residues to aromatic hydrocarbon receptors by 506.13 %. This work will provide theoretical strategies to improve the quality and safety of tea production and reduce the potential risks of harmful substance residues in tea garden soils and tea leaves.

The potential of algae and aquatic macrophytes in the pharmaceutical and personal care products (PPCPs) environmental removal: a review

The presence of emerging contaminants, such as pharmaceuticals and personal care products (PPCPs), in aquatic environments has received increasing attention in the last years due to the various possible impacts on the dynamics of the natural environment and human health. In global terms, around 771 active pharmaceutical substances or their transformation products have been detected at levels above their respective detection limit. Additionally, 528 different compounds have been detected in 159 countries. Seeking to overcome potential ecotoxicological problems, several studies have been conducted using different technologies for PPCPs removal. Recently, the use of macro, microalgae, and aquatic macrophytes has been highlighted due to the excellent bioremediation capacity of these organisms and easy acclimatization. Thus, the present review aims to outline a brief and well-oriented scenario concerning the knowledge about the bioremediation alternatives of PPCPs through the use of macro, microalgae, and aquatic macrophytes. The characteristics of PPCPs and the risks of these compounds to the environment and human health are also addressed. Moreover, the review indicates the opportunities and challenges for expanding the use of biotechnologies based on algae and aquatic macrophytes, such as studies dedicated to relate the operational criteria of these biotechnologies with the main PPCPs removal mechanisms. Finally, algae and macrophytes can compose green and ecological biotechnologies for wastewater treatment, having great contribution to PPCPs removal.

Removal of an Azo Dye from Wastewater through the Use of Two Technologies: Magnetic Cyclodextrin Polymers and Pulsed Light

Water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and acceptable in industrial use. Magnetic cyclodextrin polymers offer the advantage of easy separation from the dye solution. In this work, the β-CD-EPI-magnetic (β-cyclodextrin-epichlorohydrin) polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water, and the fraction of non-adsorbed dye was degraded by an advanced oxidation process. The polymer was characterized in terms of the particle size distribution and surface morphology (FE-SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), and X-ray powder diffraction (XRD). The reported results hint that 0.5 g and pH 5.0 were the best conditions to carry out both kinetic and isotherm models. A 30 min contact time was needed to reach equilibrium with a qmax of 32.0 mg/g. The results indicated that the pseudo-second-order and intraparticle diffusion models were involved in the assembly of Direct Red 83:1 onto the magnetic adsorbent. Regarding the isotherms discussed, the Freundlich model correctly reproduced the experimental data so that adsorption was confirmed to take place onto heterogeneous surfaces. The calculation of the thermodynamic parameters further demonstrates the spontaneous character of the adsorption phenomena (ΔG° = −27,556.9 J/mol) and endothermic phenomena (ΔH° = 8757.1 J/mol) at 25 °C. Furthermore, a good reusability of the polymer was evidenced after six cycles of regeneration, with a negligible decline in the adsorption extent (10%) regarding its initial capacity. Finally, the residual dye in solution after treatment with magnetic adsorbents was degraded by using an advanced oxidation process (AOP) with pulsed light and hydrogen peroxide (343 mg/L); >90% of the dye was degraded after receiving a fluence of 118 J/cm2; the discoloration followed a pseudo first-order kinetics where the degradation rate was 0.0196 cm2/J. The newly synthesized β-CD-EPI-magnetic polymer exhibited good adsorption properties and separability from water which, when complemented with a pulsed light-AOP, may offer a good alternative to remove dyes such as Direct Red 83:1 from water. It allows for the reuse of both the polymer and the dye in the dyeing process.

Persistent organic pollutants in water resources: Fate, occurrence, characterization and risk analysis

Persistent organic pollutants (POPs) are organic chemicals that can persist in the environment for a longer period due to their non-biodegradability. The pervasive and bio-accumulative behavior of POPs makes them highly toxic to the environmental species including plants, animals, and humans. The present review specifies the POP along with their fate, persistence, occurrence, and risk analysis towards humans. The different biological POPs degradation methods, especially the microbial degradation using bacteria, fungi, algae, and actinomycetes, and their mechanisms were described. Moreover, the source, transport of POPs to the environmental sources, and the toxic nature of POPs were discussed in detail. Agricultural and industrial activities are distinguished as the primary source of these toxic compounds, which are delivered to air, soil, and water, affecting on the social and economic advancement of society at a worldwide scale. This review also demonstrated the microbial degradation of POPs and outlines the potential for an eco-accommodating and cost-effective approach for the biological remediation of POPs using microbes. The direction for future research in eliminating POPs from the environmental sources through various microbial processes was emphasized.

Sustainable Treatment Techniques for Emerging Pollutants—The Case of Personal Hygiene Products

Personal care products (PCPs) enter wastewater primarily through greywater. Treatment plants have not been able to remove this type of contaminant, although PCP abatement techniques have been developed in recent years. The objective of the current study has been to encounter the sustainable technique that keeps the optimal balance between the criteria considered in the comparison. Therefore, a bibliographic review was conducted in scientific databases of the last eight years, demonstrating that co-composting, anaerobic–aerobic sequencing bioreactors and contaminant absorption through the use of carbon nanotubes are the ones with the least environmental impact. Subsequently, the Saaty and Modified Saaty methods were applied, with a comparative criteria of construction costs, maintenance costs, efficiency and the stage of development. The results indicated that the co-composting technique is the best sustainable technique of those studied, with a score of 0.86/1, which means that the criteria analyzed maintain very close values between them. The co-composting technique yields a low environmental impact in eliminating personal care products. This research work constitutes a practical and easy-to-use tool for decision makers, since it allows finding an optimal elimination treatment for PCPs.

A comprehensive evaluation of organic micropollutants (OMPs) pollution and prioritization in equatorial lakes from mainland Tanzania, East Africa

A lack of understanding the fate of highly toxic organic micropollutants (OMPs) in the equatorial lakes of Tanzania hinders public awareness for protecting these unique aquatic ecosystems, which are precious water resources and stunning wildlife habitats. To address this knowledge gap, the occurrence of 70 anthropogenically-sourced OMPs, including phthalates (PAEs), polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs), was investigated in the water and sediment of 18 lakes in Tanzania. Similar residue concentrations were found in both compartments, showing higher pollution of PAEs ranging from 835.0 to 13,153.1 ng/L in water and 244.6-8691.8 ng/g dw in sediment, followed by PAHs, while OCPs and PCBs were comparatively lower. According to the multi-criteria scoring method for prioritization, the final OMP priority list for the lake environment in Tanzania comprised 25 chemicals, specifically 5 PAEs (DEHP, DIBP, DBP, DCHP and DMPP), 6 PCBs (PCB153, PCB105, PCB28, PCB156, PCB157 and PCB167), 6 PAHs (BaP, BaA, BbF, Pyr, DahA and InP) and 8 OCPs (cis-chlordane, trans-chlordane, p,p'-DDD, p,p'-DDE, p,p'-DDT, endrin, methoxychlor and heptachlor epoxide), suggesting the key substances for conventional monitoring and pollution control in these equatorial lakes, with an emphasis on PAEs, especially DEHP, due to the top priority and endocrine disruptor properties.

Wastewater treatment and emerging contaminants: Bibliometric analysis

In recent years, emerging contaminants have been found in the wastewater, surface water, and even drinking water, which should be treated to ensure the safety of our living environment. In this study, we provide a comprehensive summary of wastewater treatment and emerging contaminants research from 1998 to 2021 by using the bibliometric analysis. This study is conducted based on the Web of Science Core Collection Database. The bibliometix R-package, VOSviewer and CiteSpace software are used for bibliometric analysis and science mapping. A dataset of 10, 605 publications has been retrieved. The analysis results show that China has produced the most publications. China and the United States have the closest cooperation. Analysis of the most cited papers reveals that the purification or removal techniques such as ozonation or membrane filtration can effectively remove pharmaceutical compounds from the water environment. We also found that the efficient detection of emerging contaminants and the optimization of removal methods are current challenges. Finally, future research directions are discussed.

Fe-based nanomaterial transformation to amorphous Fe: Enhanced alfalfa rhizoremediation of PCBs-contaminated soil

Nano-enabled phytoremediation is an emerging remediation strategy for soils that are moderately contaminated with persistent organic contaminants, and there is a significant need for increased mechanistic understanding and for case studies. Herein, we evaluated the remediation of PCB28-contaminated soil using combined alfalfa and Fe-based materials, including zero-valent iron at 20 nm, 100 nm, and 5 µm, and also iron oxide nanomaterials including α-Fe₂O₃, γ-Fe₂O₃, and Fe₃O₄ around 20-30 nm. Compared with alfalfa remediation alone (63.2%), Fe-based nanomaterials increased PCB28 removal values to 72.4-93.5% in planted soil, with α-Fe₂O₃ treatment promoting the most effective pollutant removal. Mechanistically, the crystalline Fe-based nanoparticles were transformed into amorphous forms in the plant rhizosphere, resulting in greater availability and enhanced iron nutrition. This nutritional shift induced root metabolic reprogramming of amino acid and carbohydrate cycling, and related functional bacterial enrichment of Ramlibacter, Dyella, Bacillus, and Paraburkholderia in rhizosphere. A significant positive correlation between amorphous iron and root metabolites-associated microbes with PCB28 removal was evident, implying that iron supplementation selected for rhizospheric microorganisms favored PCBs degradation. Overall, this rhizoremediation promotion strategy of Fe species-metabolites-microbes highlights the potential for the hybrid application of nano-enabled phytotechnology in the remediation of soils contaminated with persistent organic xenobiotics.

Response of a Coastal Microbial Community to Olivine Addition in the Muping Marine Ranch, Yantai

Spreading olivine powder in seawater to enhance alkalinity through weathering reactions has been proposed as a potential solution to control atmospheric CO₂ concentration. Attention has usually been paid to the chemical properties of seawater after the addition of olivine within lab and modeling studies. However, both microbial acclimation and evolution in such manipulated natural environments are often overlooked, yet they are of great importance for understanding the biological consequences of whether olivine addition is a feasible approach to mitigating climate change. In this study, an olivine addition experiment was conducted to investigate variation in bacterial diversity and community composition in the surface and bottom seawater of a representative marine ranch area in the Muping, Yantai. The results show that the composition of the particle-attached microbial community was particularly affected by the application of olivine. The relative abundance of biofilm-forming microbes in particle-attached fraction increased after the addition of olivine, while no significant variation in the free-living bacterial community was observed. Our study suggests that olivine addition would reshape the bacterial community structure, especially in particle-attached microenvironments. Therefore, the risk evaluation of alkalinity enhancement should be further studied before its large-scale application as a potential ocean geoengineering plan.