Spinning disc photoreactor based visible-light-driven Ag/Ag2O/TiO2 heterojunction photocatalyst film toward the degradation of amoxicillin

The spinning disc reactor for photocatalytic degradation: A systematic review

In recent years, the use of a horizontal spinning disc reactor (SDR) as a photocatalytic reactor for the degradation of various pollutants in aqueous solutions has increased. This study was searched based on the PRISMA method. Two autonomous researchers carried out for the relevant studies using Scopus, Web of Science (WOS), and Science Direct databases. The search terms expanded focusing on the performance of horizontal spinning disc photocatalytic reactor (SDPR). In this review article, the main objective of the effect of operational factors on the efficiency of the degradation of pollutants with changes in the type of light source (range of visible light and UV radiation), disc rotational speed, flow rate, initial concentration of pollutants, pH, type of disc structure and flow regime are considered. Current challenges in SDPR include issues such as limited mass transfer, uneven light distribution, and difficulties in scaling up. To overcome these challenges, improvements can be made by optimizing reactor design for better mass transfer, enhancing light distribution through advanced light sources or reactor configurations, and developing scalable models that maintain efficiency at larger scales. Additionally, the use of innovative materials and coatings could improve the overall performance of SDPR.

Recent progresses in synthesis and modification of g-C3N4 for improving visible-light-driven photocatalytic degradation of antibiotics

Graphitic carbon nitride (g-C3N4) is a widely studied visible-light-active photocatalyst for low cost, non-toxicity, and facile synthesis. Nonetheless, its photocatalytic efficiency is below par, due to fast recombination of charge carriers, low surface area, and insufficient visible light absorption. Thus, the research on the modification of g-C3N4 targeting at enhanced photocatalytic performance has attracted extensive interest. A considerable amount of review articles have been published on the modification of g-C3N4 for applications. However, limited effort has been specially contributed to providing an overview and comparison on available modification strategies for improved photocatalytic activity of g-C3N4-based catalysts in antibiotics removal. There has been no attempt on the comparison of photocatalytic performances in antibiotics removal between modified g-C3N4 and other known catalysts. To address these, our study reviewed strategies that have been reported to modify g-C3N4, including metal/non-metal doping, defect tuning, structural engineering, heterostructure formation, etc. as well as compared their performances for antibiotics removal. The heterostructure formation was the most widely studied and promising route to modify g-C3N4 with superior activity. As compared to other known photocatalysts, the heterojunction g-C3N4 showed competitive performances in degradation of selected antibiotics. Related mechanisms were discussed, and finally, we revealed current challenges in practical application.

Novel nanostructure approach for antibiotic decomposition in a spinning disc photocatalytic reactor

Conventional wastewater treatment processes are often unable to remove antibiotics with resistant compounds and low biological degradation. The need for advanced and sustainable technologies to remove antibiotics from water sources seems essential. In this regard, the effectiveness of a spinning disc photocatalytic reactor (SDPR) equipped with a visible light-activated Fe3O4@SiO2-NH2@CuO/ZnO core-shell (FSNCZ CS) thin film photocatalyst was investigated for the decomposition of amoxicillin (AMX), a representative antibiotic. Various characterization techniques, such as TEM, FESEM, EDX, AFM, XRD, and UV-Vis-DRS, were employed to study the surface morphology, optoelectronic properties, and nanostructure of the FSNCZ CS. Key operating parameters such as irradiation time, pH, initial AMX concentration, rotational speed, and solution flow rate were fine-tuned for optimization. The results indicated that the highest AMX decomposition (98.7%) was attained under optimal conditions of 60 min of irradiation time, a rotational speed of 350 rpm, a solution flow rate of 0.9 L/min, pH of 5, and an initial AMX concentration of 20 mg/L. Moreover, during the 60 min irradiation time, more than 69.95% of chemical oxygen demand and 61.2% of total organic carbon were removed. After the photocatalytic decomposition of AMX, there is a substantial increase in the average oxidation state and carbon oxidation state in SDPR from 1.33 to 1.94 and 3.2, respectively. Active species tests confirmed that ·OH and ·O2- played a dominant role in AMX decomposition. The developed SDPR, which incorporates a reusable and robust FSNCZ CS photocatalyst, demonstrates promising potential for the decomposition of organic compounds.

Decoration of 0D Bi3NbO7 nanoparticles onto 2D BiOIO3 nanosheets as visible-light responsive S-scheme photocatalyst for photo-oxidation of antibiotics in wastewater

In this work, a new S-type hybrid composed of 2D BiOIO3 and 0D Bi3NbO7 was proposed and hybridized by a facile self-assembly strategy. The developed nanomaterials were characterized and identified by a series of sophisticated analyses, like XRD, SEM, EIS, XPS, PL, UPS, EDS, BET, M-S, TEM, HRTEM, and DRS. The photocatalytic behavior of BiOIO3/Bi3NbO7 was examined and optimized against amoxicillin (AMX) and other types of antibiotics under a variety of environmental conditions, such as visible light (150 W LED), direct sunlight, pH (3-11), catalyst dosages (20-80 mg), humic acid (0-24 mg/L), AMX concentration (10-40 mg/L), and different inorganic ions (0.05 M). The optimized BiOIO3/Bi3NbO7 hybrid attained exceptional AMX degradation activity (96.5%) under visible light (60 min), with a reaction constant of up to 0.04559 min-1, exceeding bare BiOIO3 and Bi3NbO7 by 5.57 and 5.3 folds, respectively. The obtained BiOIO3/Bi3NbO7 hybrid unclosed expanded light utilization behavior compared with neat catalysts, which originates from the powerful incorporation between BiOIO3 and Bi3NbO7 in the S-type system. The radical investigations confirmed the superiority of BiOIO3/Bi3NbO7 in generating both •OH and •O2- during the photoreaction. The novel Bi3NbO7-based heterojunction afforded robust photostability in five treatment cycles and simple charge transfer activity in the S-type route, boosting the photo-mechanism for antibiotic degradation in an efficient manner. The building of the S-scheme heterojunction between BiOIO3 and Bi3NbO7 stimulates the utilization of holes by the recombination process and promotes the overall stability of the composite. Our study introduces a new class of semiconductor heterojunctions that may contribute to the development potential of the photocatalysis sector in wastewater treatment.

Enhanced photocatalytic degradation of amoxicillin using a spinning disc photocatalytic reactor (SDPR) with a novel Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure

Antibiotics are resistant compounds with low biological degradation that generally cannot be removed by conventional wastewater treatment processes. The use of yolk-shell nanostructures in spinning disc photocatalytic reactor (SDPR) enhances the removal efficiency due to their high surface-to-volume ratio and increased interaction between catalyst particles and reactants. The purpose of this study is to investigate the SDPR equipped to Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure (FCZ YS) in the presence of visible light illumination in the photocatalytic degradation of amoxicillin (AMX) from aqueous solutions. Stober, co-precipitation, and self-transformation methods were used for the synthesis of FCZ YS thin film nanostructure and the physical and chemical characteristics of the catalyst were analyzed by XRD, VSM,, EDX, FESEM, TEM, AFM, BET, contact angle (CA), and DRS. Then, the effect of different parameters including pH (3-11), initial concentration of AMX (10-50 mg/L), flow rate (10-25 mL/s) and rotational speed (100-400 rpm) at different times in the photocatalytic degradation of AMX were studied. The obtained results indicated that the highest degradation efficiency of 97.6% and constant reaction rate of AMX were obtained under LED visible light illumination and optimal conditions of pH = 5, initial AMX concentration of 30 mg/L, solution flow rate of 15 mL/s, rotational speed of 300 rpm and illumination time of 80 min. The durability and reusability of the nanostructure were tested, that after 5 runs had a suitable degradation rate. Considering the appropriate efficiency of amoxicillin degradation by FCZ YS nanostructure, the use of Fe3O4@void@CuO/ZnO thin film in SDPR is suggested in water and wastewater treatment processes.

Phototransformations of TiO2/Ag2O composites and their influence on photocatalytic water splitting accompanied by methanol photoreforming

This work aimed to revise the mechanism of photocatalytic activity of the TiO₂/Ag₂O system in photocatalytic water splitting accompanied by methanol photoreforming. The transformation of Ag₂O into silver nanoparticles (AgNPs) during photocatalytic water splitting/methanol photoreforming was monitored using XRD, XPS, SEM, UV-vis, and DRS techniques. The impact of AgNPs, grown on TiO₂, on its optoelectronic properties was analysed through inter alia spectroelectrochemical measurements. The photoreduced material exhibited a significantly shifted position of the TiO₂ conduction band edge. Surface photovoltage measurements revealed the lack of photoinduced exchange of electrons between TiO₂ and Ag₂O, indicating the absence of an efficient p-n junction. Furthermore, the impact of chemical and structural changes in the photocatalytic system on the production of CO and CO₂ from methanol photoreforming was analysed. It was found that fully formed AgNPs exhibit improved efficiency in the production of H₂, whereas the Ag₂O phototransformation, resulting in the growth of AgNPs, promotes simultaneously ongoing photoreforming of methanol.

A review of radical and non-radical degradation of amoxicillin by using different oxidation process systems

Pharmaceutical compounds have piqued the interest of researchers due to an increase in their demand, which increases the possibility of leakage into the environment. Amoxicillin (AMX) is a penicillin derivative used for the treatment of infections caused by gram-positive bacteria. AMX has a low metabolic rate in the human body, and around 80-90% is unmetabolized. As a result, AMX residuals should be treated immediately to avoid further accumulation in the environment. Advanced oxidation process techniques are an efficient way to degrade AMX. This review attempts to collect, organize, summarize, and analyze the most up to date research linked to the degradation of AMX by different advanced oxidation process systems including photocatalytic, ultrasonic, electro-oxidation, and advanced oxidation process-based on partials. The main topics investigated in this review are degradation mechanism, degradation efficiency, catalyst stability, the formation of AMX by-products and its toxicity, in addition, the influence of different experimental conditions was discussed such as pH, temperature, scavengers, the concentration of amoxicillin, oxidants, catalyst, and doping ratio. The degradation of AMX could be inhibited by very high values of pH, temperature, AMX concentration, oxidants concentration, catalyst concentration, and doping ratio. Several AMX by-products were discovered after oxidation treatment, and several of them had lower or same values of LC₅₀ (96 h) fathead minnow of AMX itself, such as m/z 384, 375, 349, 323, 324, 321, 318, with prediction values of 0.70, 1.10, 1.10 0.42, 0.42, 0.42, and 0.42 mg/L, respectively. We revealed that there is no silver bullet system to oxidize AMX from an aqueous medium. However, it is recommended to apply hybrid systems such as Photo-electro, Photo-Fenton, Electro-Fenton, etc. Hybrid systems are capable to cover the drawbacks of the single system. This review may provide important information, as well as future recommendations, for future researchers interested in treating AMX using various AOP systems, allowing them to improve the applicability of their systems and successfully oxidize AMX from an aqueous medium.

Preparation and modification methods of defective titanium dioxide-based nanoparticles for photocatalytic wastewater treatment-a comprehensive review

The rapid population growth and industrial expansion worldwide have created serious water contamination concerns. To curb the pollution issue, it has become imperative to use a versatile material for the treatment. Titanium dioxide (TiO₂) has been recognized as the most-studied nanoparticle in various fields of science and engineering due to its availability, low cost, efficiency, and other fascinating properties with a wide range of applications in modern technology. Recent studies revealed the photocatalytic activity of the material for the treatment of industrial effluents to promote environmental sustainability. With the wide band gap energy of 3.2 eV, TiO₂ can be activated under UV light; thus, many strategies have been proposed to extend its photoabsorption to the visible light region. In what follows, this has generated increasing attention to study its characteristics and structural modifications in different forms for photocatalytic applications. The present review provides an insight into the understanding of the synthesis methods of TiO₂, the current progress in the treatment techniques for the degradation of wide environmental pollutants employing modified TiO₂ nanoparticles, and the factors affecting its photocatalytic activities. Further, recent developments in using titania for practical applications, the approach for designing novel nanomaterials, and the prospects and opportunities in this exciting area have been discussed.