Ultra-trace determination of (90)Sr, (137)Cs, (238)Pu, (239)Pu, and (240)Pu by triple quadruple collision/reaction cell-ICP-MS/MS: Establishing a baseline for global fallout in Qatar soil and sediments

Gas-Phase Reactivity of Actinides Monocations with NH3: ICP-MS Experiments Combined with a DFT Study

The reactivity of actinide monocations (Th+, U+, Np+, Pu+, Am+, and Cm+) with NH3 gas was studied in the reaction cell of an inductively coupled plasma-mass spectrometer (ICP-MS). Only Th+, U+, Np+, and Cm+ react completely with NH3 to form AnNH+, contrary to Pu+ and Am+. Differences in reactivity are found between U+/Pu+, Pu+/Cm+, and Am+/Cm+, which could resolve isobaric interferences in ICP-MS. DFT calculations were performed across the first half of the actinide series. The calculated reaction energy between An+ and NH3 reproduces the experimental trends in reactivity with Th+ > Pa+ > U+ > Np+ > Ac+ > Cm+ > Pu+ > Am+. The reaction path involves the initial formation of an AnNH3+ adduct followed by N-H bond insertion with the formation of HAnNH2+ and H2AnNH+ intermediate species and subsequent H2 loss. The trend in reactivity across the actinides is largely due to the first energy barrier and formation of the HAnNH2+ intermediate species. This limiting step is energetically unfavorable for the Pu+ and Am+ cations. For these cations, the excitation energy required to achieve a reactive configuration with two non-f electrons available for bonding is too high.

Rapid and Simultaneous Determination of 238Pu, 239Pu, 240Pu, and 241Pu in Samples with High-Level Uranium Using ICP-MS/MS and Extraction Chromatography

As the most important plutonium isotopes, 238Pu, 239Pu, 240Pu, and 241Pu are normally measured by two to three techniques, which are tedious, time-consuming, and not suitable for rapid analysis in emergency situations. Recently, ICP-MS has become a competitive technique for the rapid measurement of 239Pu, 240Pu, and 241Pu. However, ICP-MS is difficult to measure 238Pu due to the serious isobaric interference of 238U. This work reports a rapid analytical method to solve this problem for the simultaneous determination of 238Pu, 239Pu, 240Pu, and 241Pu using triple-quadrupole inductively coupled plasma mass spectrometry (ICP-MS/MS) combined with chemical separation. Chemical separation achieved a high decontamination factor of 2.12 × 109 for the most critical interfering element, uranium, by using two sequential TK200 columns. The interferences of 238U1H+ and 238U+ were effectively eliminated by using 12 mL/min He-6 mL/min NH3 as the reaction gases in the octupole collision/reaction cell in ICP-MS/MS. Combined with chemical separation, the overall elimination efficiency of 238U1H+ reached 3.6 × 1017, which is 105 times better than the reported method. With the high 238U+ elimination efficiency of 1.12 × 104 in the ICP-MS/MS measurement, the overall removal efficiency of 238U+ reached 1013, guaranteeing accurate determination of femtogram-level 238Pu as well as 239Pu, 240Pu, and 241Pu in the samples containing milligram-level 238U. The detection time is reduced to minutes, well fulfilling the requirement of rapid analysis. This method is validated by analyzing the standard reference material and the spiked samples.

Innovative ICP-MS/MS Method To Determine the 135Cs/137Cs Ratio in Low Activity Environmental Samples

The ¹³⁵Cs/¹³⁷Cs isotopic ratio is a powerful tool for tracing the origin of radioactive contamination. Since the Fukushima accident, this ratio has been measured by mass spectrometry in several highly contaminated environmental matrices mainly collected near nuclear accident exclusion zones and former nuclear test areas. However, few data were reported at ¹³⁷Cs environmental levels (<1 kBq kg^-1). This is explained by the occurrence of analytical challenges related to the very low radiocesium content at the environmental level with the large presence of mass interferences, making ¹³⁵Cs and ¹³⁷Cs measurements difficult. To overcome these difficulties, a highly selective procedure for Cs extraction/separation combined with an efficient mass spectrometry measurement must be applied on a quantity of ca. 100 g of soil. In the current research, an innovative inductively coupled plasma-tandem mass spectrometry (ICP-MS/MS) method has been developed for the ¹³⁵Cs/¹³⁷Cs ratio measurement in low activity environmental samples. The use of ICP-MS/MS led to a powerful suppression of ¹³⁵Cs and ¹³⁷Cs interferences by introducing N₂O, He, and, for the first time, NH₃, into the collision-reaction cell. By adjusting the flow rates of these gases, the best compromise between a maximum signal in Cs and an effective interference elimination was achieved allowing a high Cs sensitivity of more than 1.10⁵ cps/(ng g^-1) and low background levels at m/z 135 and 137 lower than 0.6 cps. The accuracy of the developed method was successfully verified by analyzing two certified reference materials (IAEA-330 and IAEA-375) commonly used in the literature as validation samples and three sediment samples collected in the Niida River catchment (Japan) impacted by the Fukushima fallout.

Recent Development on Determination of Low-Level 90Sr in Environmental and Biological Samples: A Review

In the context of the rapid development of the world's nuclear power industry, it is vital to establish reliable and efficient radioanalytical methods to support sound environment and food radioactivity monitoring programs and a cost-effective waste management strategy. As one of the most import fission products generated during human nuclear activities, ⁹⁰Sr has been widely determined based on different analytical techniques for routine radioactivity monitoring, emergency preparedness and radioactive waste management. Herein, we summarize and critically review analytical methods developed over the last few decades for the determination of ⁹⁰Sr in environmental and biological samples. Approaches applied in different steps of the analysis including sample preparation, chemical separation and detection are systematically discussed. The recent development of modern materials for ⁹⁰Sr concentration and advanced instruments for rapid ⁹⁰Sr measurement are also addressed.

Determination, Separation and Application of 137Cs: A Review

In the context of the rapid development of the world's nuclear power industry, it is necessary to establish background data on radionuclides of different samples from different regions, and the premise of obtaining such basic data is to have a series of good sample processing and detection methods. The radiochemical analysis methods of low-level radionuclides ¹³⁷Cs (Cesium) in environmental and biological samples are introduced and reviewed in detail. The latest research progress is reviewed from the five aspects of sample pretreatment, determination, separation, calculation, application of radioactive cesium and the future is proposed.

Simultaneous determination of actinides and 90Sr in large-size soil and sediment samples

A simultaneous analytical method for sequential separation and determination of actinides and ⁹⁰Sr in large-size environmental samples has been developed. In this method, successive co-precipitation steps were firstly conducted to remove matrix elements, then sequential column separation method was applied for simultaneous separation and purification of actinides and ⁹⁰Sr/⁹⁰Y. By using vacuum box technology, the total analytical time was minimized and batch processing allowed analyzing 12 samples in four days. The activity of ⁹⁰Sr was obtained immediately by measuring its daughter radionuclide (⁹⁰Y) with triple-to-double coincidence ratio (TDCR) Cherenkov counting, while the concentrations of Pu isotopes and ²⁴¹Am could be measured by alpha spectrometry and mass spectrometric techniques. The overall recoveries of Pu, Am, Sr and Y were higher than 70% for the entire procedure, while the recovery ratios of Sr/Y were between 0.95 and 1.04 before chromatographic separation. The developed method was verified using 20 g and 50 g of environmental soil samples spiked with certified reference materials IAEA-384 or IAEA-385 and standard solution of ⁹⁰Sr/⁹⁰Y, and good agreement between the expected values and measured results has been achieved.

Estimation of radionuclides global fallout levels in the soils of CIS and eastern Europe territory

This study is devoted to the estimation of radionuclides global fallout levels in the soils of Commonwealth of Independent States (CIS) and Eastern Europe territory as a result of nuclear explosions. 58 standard soil samples were used, which were selected in different soil and climatic areas of the territory of CIS and Eastern Europe in 1978-2018. All samples were measured by gamma spectrometry. Determination of plutonium isotopes and strontium was performed according to the method of the joint determination of these radionuclides from one sample. IN the samples considered in this work, the content of ⁶⁰Co, ¹⁵⁴Eu, ¹⁵⁵Eu was below the detection limits, which were 0.4; 1.0 and 1.0, respectively. Natural radionuclides analysis results indicated that the obtained samples are typical soil samples without its abnormal contents. The content of ¹³⁷Cs, ⁹⁰Sr, ^239+240Pu in a 20 cm soil layer due to global fallout is (3.9 ± 1.7), (2.2 ± 0.8), (0.18 ± 0.08) Bq/kg respectively, which considering the distribution of these radionuclides by depth and average soil density is (1.2 ± 0.5) kBq/m² for ¹³⁷Cs, (0.42 ± 0.15) kBq/m²- ⁹⁰Sr and (55.0 ± 24.0) Bq/m²- ^239+240Pu. The isotopic ratios¹³⁷Cs/⁹⁰Sr and ¹³⁷Cs/^239+240Pu for the territory of CIS and Eastern Europe are at the level (2.0 ± 0.71) and (25 ± 15), respectively.

226Ra and 137Cs determination by inductively coupled plasma mass spectrometry: state of the art and perspectives including sample pretreatment and separation steps

Achieving precise and accurate quantification of radium (²²⁶Ra) and cesium (¹³⁷Cs) by inductively coupled plasma mass spectrometry (ICP-MS) is of particular interest in the field of radiological monitoring and more widely in environmental and biological sciences. However, the accuracy and sensitivity of the quantification depend on the analytical strategy implemented. Eliminating interferences during the sample handling step and/or during the analysis step is critical since presence of matrix elements can lead to spectral and non-spectral interferences in ICP-MS. Consequently, before the ICP-MS analysis, multiple sample preparation approaches have been applied to purify and/or pre-concentrate environmental and biological samples containing radium and cesium through years, such as (co)-precipitation, solid phase extraction (SPE) or dispersive SPE (dSPE). Separation steps using liquid chromatography and capillary electrophoresis can also be useful in complement with the abovementioned sample preparation techniques. The most attractive sample handling technique remains SPE but efficiency of the extraction procedures is currently limited by sorbent specificity. Indeed, with the recent advances in ICP-MS instrumentation, it becomes indispensable to eliminate residual interferences and improve sensitivity. It is in this direction that it will be possible to meet analytical challenges, e.g. analyzing radium and cesium at concentrations below the pg L^-1 range in complex matrices of small volumes, as they are found for instance in pore waters or in biological samples. Development of new innovative sorbents based for example on hybrid and nanostructured materials has been reported with the aim of enhancing sorbent specificity and/or capacity. In the present review, the performances of the different analytical approaches are discussed, followed by an overview of applications.

Analytical Methods for the Determination of 90Sr and 239,240Pu in Environmental Samples

Artificial long-lived radionuclides such as ⁹⁰Sr and ^239,240Pu have been long released into the environment by human nuclear activities, which have a profound impact on the ecological environment. It is of great significance to monitor the concentration of these radionuclides for environmental safety. This paper summarizes and critically discusses the separation and measurement methods for ultra-trace determination of ⁹⁰Sr, ²³⁹Pu, and ²⁴⁰Pu in the environment. After selecting the measurement method, it is necessary to consider the decontamination of the interference from matrix elements and the key elements, and this involves the choice of the separation method. Measurement methods include both radiometric methods and non-radiometric methods. Radiometric methods, including alpha spectroscopy, liquid scintillation spectrometry, etc., are commonly used methods for measuring ^239+240Pu and ⁹⁰Sr. Mass spectrometry, as the representative of non-radiometric measurement methods, has been regarded as the most promising analytical method due to its high absolute sensitivity, low detection limit, and relatively short sample-analysis time. Through the comparison of various measurement methods, the future development trend of radionuclide measurement is prospected in this review. The fully automatic and rapid analysis method is a highlight. The new mass spectrometer with ultra-high sensitivity shows strong analytical capabilities for extremely low concentrations of ⁹⁰Sr, ²³⁹Pu, and ²⁴⁰Pu, and it is expected to develop determination methods with higher sensitivity and lower detection limit.

Geogenic and anthropogenic sources identification and ecological risk assessment of heavy metals in the urban soil of Yazd, central Iran

Urban soil pollution with heavy metals is one of the environmental problems in recent years, especially in industrial cities. The aim of this study is to evaluate the role of geogenic and anthropogenic sources in the urban soil pollution in Yazd, Iran. For this purpose, 30 top-soil (0-10 cm) samples from Yazd within an area of 136.37 Km2 and population of nearly 656 thousand are collected, and the concentration of heavy elements is measured. To evaluate factors affecting the concentration of heavy elements in urban soils and determine their possible sources, Multivariate statistical analysis, including correlation coefficient, principal components analysis (PCA) and cluster analysis (CA) are performed. Enrichment Factor (EF), Geo-accumulation index (Igeo), and Modified potential ecological Risk Index (MRI) are used to assess the level and extension of contamination. Results of this study suggest that As, Cd, Pb and Zn are affected by anthropogenic source, while the concentrations of Fe, Mn, Ni, Cr, Co, Cu and Cs have come from mostly natural geologic sources. As, Cd and Pb are considerably enriched in the area, provided moderately enriched for the elements Mn, Zn and Cu. However, the other heavy elements show minimal enrichment. Igeo reveal that Co, Cr, Cs, Cu, Fe, Mn, Zn and Ni with negative values are unpolluted, Pb posed unpolluted to moderately polluted, and As and Cd represent high polluted. Based on the results of the ecological risk factor, the heavy metals of Mn, Ni, Cr, Zn and Cu have a low ecological risk level. More specifically, we find that Pb shows a moderated ecological risk in 39% of the urban soil in the studied area. As and Cd with respectively 100 and 72% contribution have considerable and very high ecological risk. According to the results of MRI, the area is in a very high ecological risk level, and appropriate management practice is essential to reduce the pollution of heavy elements in this area.

Pollution, human health risk assessment and spatial distribution of toxic metals in urban soil of Yazd City, Iran

Heavy metal pollution significantly reduces the quality of the environment and threatens human health, especially in industrial cities. This study investigated toxic metals concentrations, pollution levels and human health risks assessment of urban soils in Yazd City, as an industrial city in center of Iran. Soil surface samples (0-10 cm) were collected from 30 points in the area for geochemical analysis. The concentrations of heavy metals were determined using an inductively coupled plasma mass spectrometry (ICP-MS). The values of the mean concentrations of toxic metals (mg kg^-1) in the urban soils decrease in the order of Zn (83.9) > Pb (34.5) > Cr (32.6) > Cu (23.5) > Ni (23.4) > As (5.86) > Co (4.86) > Cd (0.27). The mean concentration of Zn, Pb, As and Cd elements was higher than the background and the crust values. A pollution assessment by Geo-accumulation Index (I_geo), Pollution Index (PI), Contamination Degree (C_D), the Integrated Pollution Index (IPI), the Pollution Load Index (PLI) and Integrated Nemerow Pollution Index (INPI) showed that As, Cd and Pb were moderately enriched and the study area polluted considerably by these toxic metals. Based on PI results, 88.9% of the urban soil samples highly polluted by As. Overall, the quality of the urban soil in Yazd City is clearly affected by toxic metals. Due to the prevailing wind direction, the route of the north-south highway of Iran and the population density and traffic of the northwestern and southern areas of the study area were found the highest level of pollution indicators (IPI > 1.8; LPI > 1.3; C_D > 15 and INPI > 4.3). The results of Pearson correlation analysis indicated that all pollution evaluation indicators were influenced by As and Cu, and showed high significant correlation with these two elements, while neither of them had a significant relationship with Pb and was found also a weak link statistically with Cd. Health risk assessment of toxic metals has been performed in both carcinogenic and non-carcinogenic sectors. The results indicate that oral intake is the main pathway that toxic metals can harm human health for both the child and adults. The carcinogenic risks (RI) of adults and child by toxic metals were as follows: Ni > Pb > Cr > As > Cd. Hazard quotients (HQ) and hazard index (HI) values for child also were higher than these for adults. Generally, the results demonstrated that the potential carcinogenic health risks for adults of toxic metals were in an acceptable range in study area, whereas for Cr, Ni and Pb with RI > 10^-4, the risk of cancer in child probably increases.

Determination of ultra-trace level plutonium isotopes in soil samples by triple-quadrupole inductively coupled plasma-mass spectrometry with mass-shift mode combined with UTEVA chromatographic separation

Although triple-quadrupole inductively coupled plasma-mass spectrometry (ICP-MS/MS) has become an attractive technique for the measurement of long-lived radionuclides, the abundance sensitivity, isobaric and polyatomic ions interferences seriously restrict the application. The spectral peak tailing and uranium hydrides (UH⁺, UH₂⁺) from ²³⁸U have a serious influence on the accurate measurement of ²³⁹Pu and ²⁴⁰Pu, especially for the ultra-trace level plutonium isotopes in the higher uranium sample. A new method was developed using ICP-MS/MS measurement in mass-shift mode with collision-reaction gas combined with a chemical separation procedure. As O₂ readily converted Pu⁺ ion to PuO₂⁺, while disassociated the interfering diatomic ions of interfering elements (U, Pb, Hg, Tl, etc.), the interferences from these elements were completely eliminated if plutonium was detected as PuO₂⁺ at the m/z more than 270. By the mass filter in MS/MS mode combined with O₂ as reaction gas the lower peak tailing of ²³⁸U⁺ (<5 × 10^-12) was significantly suppressed. By this way, the ²³⁸UO₂H⁺/²³⁸UO₂⁺ atomic ratio was reduced to 4.82 × 10^-9, which is significantly lower than that of other collision-reaction gas modes. Interferences from Pb, Hg and Tl polyatomic ions were also completely eliminated. Thus, accurate measurement of ultra-trace level ²³⁹Pu in high uranium sample solutions with the ²³⁹Pu/²³⁸U concentration ratio of 10^-10 was achieved by the mass-shift mode with 0.15 mL/min O₂/He + 12.0 mL/min He as collision-reaction gas, and high elimination efficiency of uranium interferences up to 10¹⁴ can be obtained by combination with the chemical separation using a single UTEVA resin column. The developed method can be applied to accurately determine the fg level ²³⁹Pu in high uranium samples, such as large-size deep seawater, deep soil and sediment, uranium debris of nuclear fuel.

Accurate and precise determination of 90Sr at femtogram level in IAEA proficiency test using Thermal Ionization Mass Spectrometry

A novel method for the determination of ultra-trace level ⁹⁰Sr has been recently developed applying thermal ionization mass spectrometry (TIMS). The method includes the chemical separation of Zr (isobaric interference of ⁹⁰Zr) from the samples followed by determination of ⁹⁰Sr/⁸⁸Sr abundance  sensitivity (2.1 × 10⁻¹⁰). The analytical performance of this method was assessed in the IAEA-TEL 2017-3 worldwide open proficiency test. For ⁹⁰Sr determination, tap water and milk powder samples were distributed amongst the participant laboratories with reference values of 11.2 ± 0.3 Bq kg⁻¹ (2.2 ± 0.1 fg g⁻¹) and 99.9 ± 5.0 Bq kg⁻¹ (19.5 ± 1.0 fg g⁻¹), respectively. The stable Sr concentrations were 39.4 ± 0.9 ng g⁻¹ and 2.5 ± 0.1 µg g⁻¹ while the ⁹⁰Sr/⁸⁸Sr isotope ratios were 6.47 ± 0.17 × 10⁻⁸ and 9.04 ± 0.45 × 10⁻⁹ in the tap water and milk powder samples, respectively. For TIMS measurement, 50 mL water and 1 g milk powder samples were taken for analysis. This TIMS method demonstrated an impressive accuracy (relative bias of 4.2% and −2.1%, respectively) and precision (relative combined uncertainty of 4.1% and 7.6%, respectively) when compared with radiometric techniques. For the first time in the history of inorganic mass-spectrometry, ⁹⁰Sr analysis using a TIMS instrument is confirmed by an independent proficiency test.

Method for 90Sr Analysis in Environmental Samples Using Thermal Ionization Mass Spectrometry with Daly Ion-Counting System

In this work, a new ⁹⁰Sr analysis method was developed using the Isotopx Ltd., Phoenix X62 thermal ionization mass spectrometer (TIMS). Excellent ion beam sensitivity was demonstrated with the detection of 1 mBq (0.2 fg) ⁹⁰Sr on a Daly ion-counting system. The abundance sensitivity for the ⁹⁰Sr/⁸⁸Sr ratio was 2.1 × 10^-10, and this could ensure measurement of 100 Bq·kg^-1 (19 fg·g^-1) ⁹⁰Sr in an environmental sample with 100 μg·g^-1 stable strontium concentration. For analytical method validation, ⁹⁰Sr was determined in two certified reference materials, for example, wild berry (IRMM-426) and freshwater lake sediment (NIST-4354), for the first time in the history of TIMS. This mass spectrometry method is faster than conventional radiometric techniques; however, interference from ⁹⁰Zr and peak tailing on the higher mass side from ⁸⁸Sr must be considered for a reliable ⁹⁰Sr determination.

A review of measurement methodologies and their applications to environmental 90Sr

The high fission yield product ⁹⁰Sr has been released into the environment in large amounts due to nuclear weapon tests, nuclear power plant accidents, and nuclear fuel reprocessing industries. It is a long half-life radionuclide (28.9 y), with serious consequences to human health; hence, it is desirable to perform routine monitoring of ⁹⁰Sr in environmental samples. Many ⁹⁰Sr radiometric methods have been developed in the past decades, which generally require complicated separation and purification steps with a relatively long analytical time. Moreover, some nominally rapid methods usually have high method detection limits, making them unsuitable for the environmental samples with ultra-low ⁹⁰Sr levels. In this review, some rapid and practical methods for ⁹⁰Sr routine monitoring are summarized. Different sample pretreatments and major purification procedures for ⁹⁰Sr developed in recent years, such as variable digestion methods and extraction chromatography using Sr resin or DGA resin, are especially described. Additionally, four conventional and widely used β spectrometric and mass spectrometric methods are demonstrated. Finally, ⁹⁰Sr evaluations focusing on contaminated soil and seawater samples collected after the Fukushima Daiichi Nuclear Power Plant accident, and ⁹⁰Sr application as tracers for environmental behavior are also reviewed.

Determination of ultra-low level plutonium isotopes (239Pu, 240Pu) in environmental samples with high uranium

In order to measure trace plutonium and its isotopes ratio (²⁴⁰Pu/²³⁹Pu) in environmental samples with a high uranium, an analytical method was developed using radiochemical separation for separation of plutonium from matrix and interfering elements including most of uranium and ICP-MS for measurement of plutonium isotopes. A novel measurement method was established for extensively removing the isobaric interference from uranium (²³⁸U¹H and ²³⁸UH₂⁺) and tailing of ²³⁸U, but significantly improving the measurement sensitivity of plutonium isotopes by employing NH₃/He as collision/reaction cell gases and MS/MS system in the triple quadrupole ICP-MS instrument. The results show that removal efficiency of uranium interference was improved by more than 15 times, and the sensitivity of plutonium isotopes was increased by a factor of more than 3 compared to the conventional ICP-MS. The mechanism on the effective suppress of ²³⁸U interference for ²³⁹Pu measurement using NH₃-He reaction gases was explored to be the formation of UNH⁺ and UNH₂⁺ in the reactions of UH⁺ and U⁺ with NH₃, while no reaction between NH₃ and Pu⁺. The detection limits of this method were estimated to be 0.55 fg mL^-1 for ²³⁹Pu, 0.09 fg mL^-1 for ²⁴⁰Pu. The analytical precision and accuracy of the method for Pu isotopes concentration and ²⁴⁰Pu/²³⁹Pu atomic ratio were evaluated by analysis of sediment reference materials (IAEA-385 and IAEA-412) with different levels of plutonium and uranium. The developed method were successfully applied to determine ²³⁹Pu and ²⁴⁰Pu concentrations and ²⁴⁰Pu/²³⁹Pu atomic ratios in soil samples collected in coastal areas of eastern China.

Development of an optimised method for analysis of 90Sr in decommissioning wastes by triple quadrupole inductively coupled plasma mass spectrometry

The ongoing development of an optimised procedure for the measurement of ⁹⁰Sr in decommissioning samples using the latest generation triple quadrupole inductively coupled plasma mass spectrometry (ICP-QQQ-MS) is presented. The procedure incorporates digestion, and separation from interferences using a combination of wet chemical and instrument-based separation using the ICP-QQQ-MS reaction cell. The key factors under study are the procedural time and limits of detection achievable compared to existing radiometric techniques.