Opportunities and challenges in CO2 utilization

High CO2 permeation using a new Ce0.85Gd0.15O2-δ-LaNiO3 composite ceramic-carbonate dual-phase membrane

This work shows the synthesis, characterization and evaluation of dense-ceramic membranes made of Ce0.85Gd0.15O2-δ-LaNiO3 (CG-LN) composites, where the fluorite-perovskite ratio (CG:LN) was varied as follows: 75:25, 80:20 and 85:15 wt.%. Supports were initially characterized by XRD, SEM and electrical conductivity (using vacuum and oxygen atmospheres), to determine the composition, microstructural and ionic-electronic conductivity properties. Later, supports were infiltrated with an eutectic carbonates mixture, producing the corresponding dense dual-phase membranes, in which CO2 permeation tests were conducted. Here, CO2 permeation experiments were performed from 900 to 700°C, in the presence and absence of oxygen (flowed in the sweep membrane side). Results showed that these composites possess high CO2 permeation properties, where the O2 addition significantly improves the ionic conduction on the sweep membrane side. Specifically, the GC80-LN20 composition presented the best results due to the following physicochemical characteristics: high electronic and ionic conductivity, appropriate porosity, interconnected porous channels, as well as thermal and chemical stabilities between the composite support and carbonate phases.

Emerging trends in hydrogen and synfuel generation: a state-of-the-art review

The current work investigated emerging fields for generating and consuming hydrogen and synthetic Fischer-Tropsch (FT) fuels, especially from detrimental greenhouse gases, CO2 and CH4. Technologies for syngas generation ranging from partial oxidation, auto-thermal, dry, photothermal and wet or steam reforming of methane were adequately reviewed alongside biomass valorisation for hydrogen generation, water electrolysis and climate challenges due to methane flaring, production, storage, transportation, challenges and opportunities in CO2 and CH4 utilisation. Under the same conditions, dry reforming produces more coke than steam reforming. However, combining the two techniques produces syngas with a high H2/CO ratio, which is suitable for producing long-chain hydrocarbons. Although the steam methane reforming (SMR) process has been industrialised, it is well known to consume significant energy. However, coke production via catalytic methane decomposition, the prime hindrance to large-scale implementation of these techniques for hydrogen production, could be addressed by coupling CO with CO2 conversion to alter the H2/CO ratio of syngas, increasing the reaction temperatures in dry reforming, or increasing the steam content fed in steam reforming. Optimised hydrogen production and generation of green fuels from CO2 and CH4 can be achieved by implementing these strategies.

Regulation on C2-C8 carboxylic acid biosynthesis from anaerobic CO2 fermentation

Bioconversion of CO2 into liquid fuels or chemicals, preferred medium chain carboxylic acids (caproic and caprylic acid), is an attractive CO2 utilization technology. The present study aims to investigate the effects of different ratios of H2/CO2 on regulating the distribution of C2-C8 carboxylic acid products, while the headspace pressure of 1.5 bar was set to amplify the effect of different ratios. The H2/CO2 ratio of 4:1 was more suitable for preparing acetic acid, where the highest acetic acid yield was 17.5 g/L. And the H2/CO2 ratio of 2:1 showed excellent chain elongation ability with the highest n-caprylic yield of 2.4 g/L. Additionally, the actual H2/CO2 ratios of 4:1 reactors were higher than that in 2:1 may be course chain elongation often accompanied by H2 production. The 16S rRNA genes analysis shows that the genus Terrisporobacter and Coriobacteriales may be related to acetic acid production enriched in H2/CO2 ratio 4:1 reactors, and the genus Clostridium and Paenibacillaceae may associate with the chain elongation pathway were enriched in H2/CO2 ratio 2:1 reactors.

Advances in Defect Engineering of Metal Oxides for Photocatalytic CO2 Reduction

Photocatalytic CO2 reduction technology, capable of converting low-density solar energy into high-density chemical energy, stands as a promising approach to alleviate the energy crisis and achieve carbon neutrality. Semiconductor metal oxides, characterized by their abundant reserves, good stability, and easily tunable structures, have found extensive applications in the field of photocatalysis. However, the wide bandgap inherent in metal oxides contributes to their poor efficiency in photocatalytic CO2 reduction. Defect engineering presents an effective strategy to address these challenges. This paper reviews the research progress in defect engineering to enhance the photocatalytic CO2 reduction performance of metal oxides, summarizing defect classifications, preparation methods, and characterization techniques. The focus is on defect engineering, represented by vacancies and doping, for improving the performance of metal oxide photocatalysts. This includes advancements in expanding the photoresponse range, enhancing photogenerated charge separation, and promoting CO2 molecule activation. Finally, the paper provides a summary of the current issues and challenges faced by defect engineering, along with a prospective outlook on the future development of photocatalytic CO2 reduction technology.

Cu-based catalyst designs in CO2 electroreduction: precise modulation of reaction intermediates for high-value chemical generation

The massive emission of excess greenhouse gases (mainly CO2) have an irreversible impact on the Earth's ecology. Electrocatalytic CO2 reduction (ECR), a technique that utilizes renewable energy sources to create highly reduced chemicals (e.g. C2H4, C2H5OH), has attracted significant attention in the science community. Cu-based catalysts have emerged as promising candidates for ECR, particularly in producing multi-carbon products that hold substantial value in modern industries. The formation of multi-carbon products involves a range of transient intermediates, the behaviour of which critically influences the reaction pathway and product distribution. Consequently, achieving desirable products necessitates precise regulation of these intermediates. This review explores state-of-the-art designs of Cu-based catalysts, classified into three categories based on the different prospects of the intermediates' modulation: heteroatom doping, morphological structure engineering, and local catalytic environment engineering. These catalyst designs enable efficient multi-carbon generation in ECR by effectively modulating reaction intermediates.

Dual active sites over Cu-ZnO-ZrO2 catalysts for carbon dioxide hydrogenation to methanol

CO₂ hydrogenation to methanol is a significant approach to tackle the problem of global warming and simultaneously meet the demand for the portable fuel. Cu-ZnO catalysts with various kinds of promoters have received wide attention. However, the role of promoter and the form of active sites in CO₂ hydrogenation are still in debate. Here, various molar ratios of ZrO₂ were added into the Cu-ZnO catalysts to tune the distributions of Cu⁰ and Cu⁺ species. A volcano-like trend between the ratio of Cu⁺/ (Cu⁺ + Cu⁰) and the amount of ZrO₂ is presented, among which the CuZn10Zr (the molar ratio of ZrO₂ is 10%) catalyst reaches the highest value. Correspondingly, the maximum value of space-time yield to methanol with 0.65 g_MeOH/(g_cat·hr) is obtained on CuZn10Zr at reaction conditions of 220°C and 3 MPa. Detailed characterizations demonstrate that dual active sites are proposed during CO₂ hydrogenation over CuZn10Zr catalyst. The exposed Cu⁰ takes participate in the activation of H₂, while on the Cu⁺ species, the intermediate of formate from the co-adsorption of CO₂ and H₂ prefers to be further hydrogenated to CH₃OH than decomposing into the by-product of CO, yielding a high selectivity of methanol.

Ti3 C2 -modified g-C3 N4 /MoSe2 S-Scheme Heterojunction with Full-Spectrum Response for CO2 Photoreduction to CO and CH4

Energy shortage and global warming caused by the extensive use of fossil fuels are urgent problems to be solved at present. Photoreduction of CO2 is considered to be a feasible solution. The ternary composite catalyst g-C3 N4 /Ti3 C2 /MoSe2 was synthesized by hydrothermal method, and its physical and chemical properties were studied by an array of characterization and tests. In addition, the photocatalytic performance of this series of catalysts under full spectrum irradiation was also tested. It is found that the CTM-5 sample has the best photocatalytic activity, and the yields of CO and CH4 are 29.87 and 17.94 μmol g-1  h-1 , respectively. This can be ascribed to the favorable optical absorption performance of the composite catalyst in the full spectrum and the establishment of S-scheme charge transfer channel. The formation of heterojunctions can effectively promote charge transfer. The addition of Ti3 C2 materials provides plentiful active sites for CO2 reaction, and its superior electrical conductivity is also favorable for the migration of photogenerated electrons.

CO2 Reduction by Nanosecond-Plasma Discharges: Revealing the Dissociation's Time Scale and the Importance of Pulse Sequence

Power-to-chemical technologies with CO₂ as feedstock recycle CO₂ and store energy into value-added compounds. Plasma discharges fed by renewable electricity are a promising approach to CO₂ conversion. However, controlling the mechanisms of plasma dissociation is crucial to improving the efficiency of the technology. We have investigated pulsed nanosecond discharges, showing that while most of the energy is deposited in the breakdown phase, CO₂ dissociation only occurs after an order of microsecond delay, leaving the system in a quasi-metastable condition in the intervening time. These findings indicate the presence of delayed dissociation mechanisms mediated by CO₂ excited states rather than direct electron impact. This "metastable" condition, favorable for an efficient CO₂ dissociation, can be prolonged by depositing more energy in the form of additional pulses and critically depends on a sufficiently short interpulse time.

Advances in CO2 utilization employing anisotropic nanomaterials as catalysts: a review

Anisotropic nanomaterials are materials with structures and properties that vary depending on the direction in which they are measured. Unlike isotropic materials, which exhibit uniform physical properties in all directions, anisotropic materials have different mechanical, electrical, thermal, and optical properties in different directions. Examples of anisotropic nanomaterials include nanocubes, nanowires, nanorods, nanoprisms, nanostars, and so on. These materials have unique properties that make them useful in a variety of applications, such as electronics, energy storage, catalysis, and biomedical engineering. One of the key advantages of anisotropic nanomaterials is their high aspect ratio, which refers to the ratio of their length to their width, which can enhance their mechanical and electrical properties, making them suitable for use in nanocomposites and other nanoscale applications. However, the anisotropic nature of these materials also presents challenges in their synthesis and processing. For example, it can be difficult to align the nanostructures in a specific direction to impart modulation of a specific property. Despite these challenges, research into anisotropic nanomaterials continues to grow, and scientists are working to develop new synthesis methods and processing techniques to unlock their full potential. Utilization of carbon dioxide (CO₂) as a renewable and sustainable source of carbon has been a topic of increasing interest due to its impact on reducing the level of greenhouse gas emissions. Anisotropic nanomaterials have been used to improve the efficiency of CO₂ conversion into useful chemicals and fuels using a variety of processes such as photocatalysis, electrocatalysis, and thermocatalysis. More study is required to improve the usage of anisotropic nanomaterials for CO₂ consumption and to scale up these technologies for industrial use. The unique properties of anisotropic nanomaterials, such as their high surface area, tunable morphology, and high activity, make them promising catalysts for CO₂ utilization. This review article discusses briefly about various approaches towards the synthesis of anisotropic nanomaterials and their applications in CO₂ utilization. The article also highlights the challenges and opportunities in this field and the future direction of research.

High pressure CO2 adsorption onto Malaysian Mukah-Balingian coals: Adsorption isotherms, thermodynamic and kinetic investigations

CO₂ sequestration into coalbed seams is one of the practical routes for mitigating CO₂ emissions. The adsorption mechanisms of CO₂ onto Malaysian coals, however, are not yet investigated. In this research CO₂ adsorption isotherms were first performed on dry and wet Mukah-Balingian coal samples at temperatures ranging from 300 to 348 K and pressures up to 6 MPa using volumetric technique. The dry S1 coal showed the highest CO₂ adsorption capacity of 1.3 mmol g^-1, at 300 K and 6 MPa among the other coal samples. The experimental results of CO₂ adsorption were investigated using adsorption isotherms, thermodynamics, and kinetic models. Nonlinear analysis has been employed to investigate the data of CO₂ adsorption onto coal samples via three parameter isotherm equilibrium models, namely Redlich Peterson, Koble Corrigan, Toth, Sips, and Hill, and four parameter equilibrium model, namely Jensen Seaton. The results of adsorption isotherm suggested that the Jensen Seaton model described the experimental data well. Gibb's free energy change values are negative, suggesting that CO₂ adsorption onto the coal occurred randomly. Enthalpy change values in the negative range established that CO₂ adsorption onto coal is an exothermic mechanism. Webber's pore-diffusion model, in particular, demonstrated that pore-diffusion was the main controlling stage in CO₂ adsorption onto coal matrix. The activation energy of the coals was calculated to be below -13 kJ mol^-1, indicating that adsorption of CO₂ onto coals occurred through physisorption. The results demonstrate that CO₂ adsorption onto coal matrix is favorable, spontaneous, and the adsorbed CO₂ molecules accumulate more onto coal matrix. The observations of this investigation have significant implications for a more accurate measurement of CO₂ injection into Malaysian coalbed seams.

Decarbonization of Power and Industrial Sectors: The Role of Membrane Processes

Carbon dioxide (CO₂) is the single largest contributor to climate change due to its increased emissions since global industrialization began. Carbon Capture, Storage, and Utilization (CCSU) is regarded as a promising strategy to mitigate climate change, reducing the atmospheric concentration of CO₂ from power and industrial activities. Post-combustion carbon capture (PCC) is necessary to implement CCSU into existing facilities without changing the combustion block. In this study, the recent research on various PCC technologies is discussed, along with the membrane technology for PCC, emphasizing the different types of membranes and their gas separation performances. Additionally, an overall comparison of membrane separation technology with respect to other PCC methods is implemented based on six different key parameters-CO₂ purity and recovery, technological maturity, scalability, environmental concerns, and capital and operational expenditures. In general, membrane separation is found to be the most competitive technique in conventional absorption as long as the highly-performed membrane materials and the technology itself reach the full commercialization stage. Recent updates on the main characteristics of different flue gas streams and the Technology Readiness Levels (TRL) of each PCC technology are also provided with a brief discussion of their latest progresses.

Enhanced sustainable integration of CO2 utilization and wastewater treatment using microalgae in circular economy concept

Microalgae have been shown to have a promising potential for CO₂ utilization and wastewater treatment which still faces the challenges of high resource and energy requirements. The implementation of the circular economy concept is able to address the issues that limit the application of microalgae-based technologies. In this review, a comprehensive discussion on microalgae-based CO₂ utilization and wastewater treatment was provided, and the integration of this technology with the circular economy concept, for long-term economic and environmental benefits, was described. Furthermore, technological challenges and feasible strategies towards the improvement of microalgae cultivation were discussed. Finally, necessary regulations and effective policies favoring the implementation of microalgae cultivation into the circular economy were proposed. These are discussed to support sustainable development of microalgae-based bioremediation and bioproduction. This work provides new insights into the implementation of the circular economy concept into microalgae-based CO₂ utilization and wastewater treatment to enhance sustainable production.

Net-Zero Action Recommendations for Scope 3 Emission Mitigation Using Life Cycle Assessment

Greenhouse gas emissions anywhere across the value chain cause the global temperature to rise. A responsible net-zero strategy is reducing and removing direct and indirect greenhouse gas emissions. The current net-zero actions aim to offset rather than reduce or remove life cycle greenhouse gas emissions (GHG). Unless the demands/consumptions are reduced, net-zero actions will merely be a burden-shifting practice. Scope 3 emissions are considered in the life cycle assessment (LCA) of goods and services and account for direct and indirect emissions with imported goods and services. Scope 3 emission tariff seems an effective way to shift consumption patterns to carbon-neutral options. This article explores tools and systems for ‘just transition’ using three buckets of scientific questions: (1) Technical: which GHG to remove, when, where, and by what mechanism; (2) Social-Policy: how to share GHG obligations between stakeholders to deliver the UN SDGs; (3) Data: how to create robust, trusted, and transparent data for reporting, accounting, and actions. Building on the analyses, this study recommends thirteen scientific evidence-based net-zero actions.

Insights into the Capture of CO2 by Nickel Hydride Complexes

As a desired feedstock for sustainable energy source and for chemical synthesis, the capture and utilization of CO2 have attracted chemists’ continuous efforts. The homogeneous CO2 insertion into a nickel hydride complex to generate formate provides insight into the role of hydrogen as an active hydride form in the hydrogenation of CO2, which serves as a practicable approach for CO2 utilization. To parameterize the activities and to model the structure–activity relationship in the CO2 insertion into nickel hydride, the comprehensive mechanism of CO2 insertion into a series of square planar transition metal hydride (TM–H, TM = Ni, Pd, and Co) complexes was investigated using density functional theory (DFT) computations. The stepwise pathway with the TM-(H)-formate intermediate for the CO2 insertion into all seven square planar transition metal hydride (TM–H) complexes was observed. The overall rate-determining step (RDS) was the nucleophilic attraction of the terminal O atom on the Ni center in Ni-(H)-formate to form Ni-(O)-(exo)formate. The charge of the Ni atom in the axially vacant [Ni]+ complex was demonstrated as the dominant factor in CO2 insertion, which had an excellent linear correction (R2 = 0.967) with the Gibbs barrier (ΔG‡) of the RDS. The parameterized activities and modeled structure–activity relationship provided here light the way to the design of a more efficient Ni–H complex in the capture and utilization of CO2.

A state-of-the-art review of CO2 enhanced oil recovery as a promising technology to achieve carbon neutrality in China

Although there are some review papers on carbon capture, utilization and storage (CCUS), hardly any of these reviews are focused on the role of CO₂ enhanced oil recovery (EOR) in accelerating carbon neutrality in China. In this review, strategies to achieve carbon neutrality is briefly but critically discussed, followed by a review of CO₂-EOR as a promising technology. Especially, data analysis, including the number of publications on China's carbon neutrality, per capita CO₂ emissions, China's power generation, and the crude oil production of China's large oilfields, is carried out to make the discussion more comprehensive. Given the large amount of coal consumed in China, the high percent of electricity generated with coal, and the slow penetration of renewables already observed, it seems unlikely that 2060 targets will be met without CCUS. In order to achieve carbon neutrality, both reduction in carbon emissions and increase in carbon sequestration are inevitable. Furthermore, it is concluded that CO₂ storage through EOR is likely to have a bright future. However, there are some critical issues to be solved, including the technical issues, leakage and safety issues, cost issues, policy issues, etc. In order to turn CO₂-EOR into a reliable and more favorable technology, more research and efforts are needed to solve these issues, including advancing carbon capture technologies, improving storage technologies, developing effective monitoring technologies, deploying government support and incentive policies, etc.

Structures, Electronic Properties, and Gas Permeability of 3D Pillared Silicon Carbide Nanostructures

Silicon carbide (SiC) is recognized as excellent material for high power/temperature applications with a wide-band gap semiconductor. With different structures at the nanosize scale, SiC nanomaterials offer outstanding mechanical, physical, and chemical properties leading to a variety of applications. In this work, new 3D pillared SiC nanostructures have been designed and investigated based on self-consistent charge density functional tight-binding (SCC-DFTB) including Van der Waals dispersion corrections. The structural and electronic properties of 3D pillared SiC nanostructures with effects of diameters and pillar lengths have been studied and compared with 3D pillared graphene nanostructures. The permeability of small gas molecules including H₂O, CO₂, N₂, NO, O₂, and NO₂ have been demonstrated with different orientations into the 3D pillared SiC nanostructures. The promising candidate of 3D pillared SiC nanostructures for gas molecule separation application at room temperature is highlighted.

Life Cycle Based Climate Emissions of Charcoal Conditioning Routes for the Use in the Ferro-Alloy Production

Renewable reductants are intended to significantly reduce CO2 emissions from ferro-alloy production, e.g., by up to 80% in 2050 in Norway. However, charcoals provide inferior properties compared to fossil fuel-based reductants, which can hamper large replacement ratios. Therefore, conditioning routes from coal beneficiation was investigated to improve the inferior properties of charcoal, such as mechanical strength, volatile matter, CO2 reactivity and mineral matter content. To evaluate the global warming potential of renewable reductants, the CO2 emissions of upgraded charcoal were estimated by using a simplified life cycle assessment, focusing on the additional emissions by the energy demand, required chemicals and mass loss for each process stage. The combination of ash removal, briquetting and high-temperature treatment can provide a renewable coke with superior properties compared to charcoal, but concomitantly decrease the available biomass potential by up to 40%, increasing the CO2-based global warming potential of industrial produced charcoal to ≈500 kg CO2-eq. t−1 FC. Based on our assumptions, CO2 emissions from fossil fuel-based reductants can be reduced by up to 85%. A key to minimizing energy or material losses is to combine the pyrolysis and post-treatment processes of renewable reductants to upgrade industrial charcoal on-site at the metallurgical plant. Briquetting showed the largest additional global warming potential from the investigated process routes, whereas the high temperature treatment requires a renewable energy source to be sustainable.

Chemical Looping Combustion: A Brief Overview

The current development of chemical looping combustion (CLC) technology is presented in this paper. This technique of energy conversion enables burning of hydrocarbon fuels with dramatically reduced CO2 emission into the atmosphere, since the inherent separation of carbon dioxide takes place directly in a combustion unit. In the beginning, the general idea of the CLC process is described, which takes advantage of solids (so-called oxygen carriers) being able to transport oxygen between combustion air and burning fuel. The main groups of oxygen carriers (OC) are characterized and compared, which are Fe-, Mn-, Cu-, Ni-, and Co-based materials. Moreover, different constructions of reactors tailored to perform the CLC process are described, including fluidized-bed reactors, swing reactors, and rotary reactors. The whole systems are based on the chemical looping concept, such as syngas CLC (SG-CLC), in situ Gasification CLC (iG-CLC), chemical looping with oxygen uncoupling (CLOU), and chemical looping reforming (CLR), are discussed as well. Finally, a comparison with other pro-CCS (carbon capture and storage) technologies is provided.