Modelling of shear rate distribution in two planetary mixtures for studying development of cake batter structure

Interplay between bulk aggregates, surface properties and foam stability of nonionic surfactants

In our previous study (Mustan et al. 2021) we showed that foams formed from two oil-soluble nonionic surfactants (Span 60 and Brij 72) can remain stable for more than 10 days at room temperature at high sugar concentration. The major aim of the current study is to reveal the interrelation between the surfactant structure and foam stability by investigating 6 polyoxyethelene alkyl ethers and 12 fatty acid esters with a wide variety of hydrophobic chain lengths (C12; C16; C18 and C18:1) and hydrophilic head-groups (sorbitol, glycerol, sucrose). Foams stable for more than 100 days at room temperature are obtained when sucrose palmitate or stearate (P1670 or S1670) are used as surfactants. This exceptional foam stability is related to the gelation of the aqueous phase and to the formation of solid adsorption layer with zero surface tension upon compression, thus preventing water drainage and decelerating the bubble Ostwald ripening. The foam stability decreases with (i) increasing the number of EO groups in polyoxyethylene alkyl ethers and in fatty acid sorbitan esters; (ii) decreasing the number of C-atoms in the surfactant tail for all studied surfactants; (iii) addition of double bond in the surfactant tail. The lower foam stability in all three cases is related to the worse packing of the surfactant molecules within the adsorption layer, leading to faster Ostwald ripening and subsequent bubble coalescence. The diesters present as admixture in the fatty acid esters play an important role in the foam stabilization by further compacting the adsorption layers and lowering the rate of Ostwald ripening. These conclusions can be used as a predictive tool for surfactant selection in the development of food or pharmaceutical foam concentrates that can be diluted before final use.

96-well microtiter plates for biofouling simulation in biomedical settings

Microtiter plates with 96 wells are routinely used in biofilm research mainly because they enable high-throughput assays. These platforms are used in a variety of conditions ranging from static to dynamic operation using different shaking frequencies and orbital diameters. The main goals of this work were to assess the influence of nutrient concentration and flow conditions on biofilm formation by Escherichia coli in microtiter plates and to define the operational conditions to be used in order to simulate relevant biomedical scenarios. Assays were performed in static mode and in incubators with distinct orbital diameters using different concentrations of glucose, peptone and yeast extract. Computational fluid dynamics (CFD) was used to simulate the flow inside the wells for shaking frequencies ranging from 50 to 200 rpm and orbital diameters from 25 to 100 mm. Higher glucose concentrations enhanced adhesion of E. coli in the first 24 h, but variation in peptone and yeast extract concentration had no significant impact on biofilm formation. Numerical simulations indicate that 96-well microtiter plates can be used to simulate a variety of biomedical scenarios if the operating conditions are carefully set.

Efficient control of the rheological and surface properties of surfactant solutions containing C8-C18 fatty acids as cosurfactants

Systematic experimental study is performed about the effects of chain length (varied between C8 and C18) and concentration of fatty acids (FAc), used as cosurfactants to the mixture of the anionic surfactant SLES and the zwitterionic surfactant CAPB. The following properties are studied: bulk viscosity of the concentrated solutions (10 wt % surfactants), dynamic and equilibrium surface tensions, surface modulus, and foam rheological properties for the diluted foaming solutions (0.5 wt % surfactants). The obtained results show that C8-C10 FAc induce formation of wormlike micelles in the concentrated surfactant solutions, which leads to transformation of these solutions into viscoelastic fluids with very high apparent viscosity. The same FAc shorten the characteristic adsorption time of the diluted solutions by more than 10 times. In contrast, C14-C18 FAc have small effect on the viscosity of the concentrated solutions but increase the surface modulus above 350 mN/m, which leads to higher friction inside sheared foams and to much smaller bubbles in the formed foams. The intermediate chain C12 FAc combines some of the properties seen with C10 FAc and other properties seen with C14 FAc. These results clearly demonstrate how appropriate cosurfactants can be used for efficient control of the rheological properties of concentrated surfactant solutions and of some important foam attributes, such as bubble size and foam rheology.