Cr(III)-imprinted polymeric beads: Sorption and preconcentration studies

A novel zwitterionic magnetic nanocomposite developed for non-invasive speciation analysis of inorganic chromium

3-(2-Aminoethylamino)propyltriethoxysilane and carboxyethylsilanetriol sodium salt were grafted on silica-coated Fe3O4 nanoparticles via sol-gel process to prepare novel amine- and carboxyl-bifunctionalized magnetic nanocomposites (SMNPs-(NH2 + COOH)). After well characterized, this doubly functionalized material was used as magnetic solid-phase extraction (MSPE) adsorbent to separate and enrich inorganic chromium species followed by inductively coupled plasma-mass spectrometry detection. The optimization of MSPE operation parameters including pH was conducted. It is reasonably elucidated that the adsorption mechanisms of zwitterionic SMNPs-(NH2 + COOH) towards chromium species are electrostatic and/or coordination interactions. Cr(VI) and Cr(III) can be adsorbed around pH 3.0 and around 10.0 respectively with strong anti-interference ability not only from other co-existing ions but also from the two labile species each other, and eluted by dilute nitric acid solution. With a 15-fold enrichment factor, the limits of detection of Cr(VI) and Cr(III) were 0.008 and 0.009 μg L-1, respectively, profiting from the maximum adsorption capacities of 7.52 and 6.11 mg g-1. The just one magnetic extraction matrix based speciation scheme possesses excellent convenience and friendliness to Cr(VI) and Cr(III) without any oxidation or reduction prior to capture of these two species. This protocol has been successfully applied to the speciation analysis of inorganic chromium in real-world environmental water samples.

Ion imprinted differential modulation system based on enhanced optic-fiber evanescent wave for sensitive and label-free detection of trace nickel ions

An optical system with low cost monitoring, high sensitivity, strong selectivity and much lower nickel ion (Ni2+) content in tap water than the World Health Organization (WHO) standard (1.19 μM) has been prepared by a simple strategy. This proposed ion-imprinted differential modulation system is based on the Bragg grating (FBG) and microfiber interferometer structure, and the interferometer sensing surface is coated with a polydopamine (PDA)/graphene oxide (GO) film to enhance its sensitivity. Combined with the ion imprinting technique, the microfiber interferometer sensor sensitivity can reach 0.32 nm/nM with the detection limit of 0.66 nM in the low concentration range (Ni2+ concentration range is 0 nM-100 nM). The experiment not only studies the principle of microfiber interferometer and FBG and their refractive index and temperature performance, but also shows that the FBG power change has a good fitting relationship with wavelength change. In addition, this system performance by the amount of power difference rather than the amount of wavelength shift, which significantly saves on the high cost weight, and size associated with the use of spectral analyzers in traditional inspection systems. This study provides a novel and easy method to develop new sensors with higher comprehensive performance.

Green synthesis of a mesoporous hyper-cross-linked polyamide/polyamine 3D network through Michael addition for the treatment of heavy metals and organic dyes contaminated wastewater

Environmental pollution is the greatest challenge of the modern age due to unprecedented industrialization and urbanization that has led to the contamination of water resources with a wide range of pollutants. The release of untreated industrial and municipal wastewater to water bodies further intensifies the problem. The presence of heavy metals and organic contaminants in water poses significant threats to humans, aquatic life, and the environment. Adsorption is one of the famous water treatment technologies due to its simplicity, low cost, efficiency, and minimal secondary pollution. The selection or synthesis of an effective adsorbent is key to the success of the adsorptive removal of pollutants. In this work, we synthesized an adsorbent consisting of a mesoporous hyper-cross-linked polyamide/polyamine 3D network through a single-step Michael addition reaction. The adsorbent was characterized by FTIR, PXRD, TGA, SEM, and TEM to investigate its functional moieties, material nature, thermal, morphological, and internal structural features, respectively. Due to its mesoporous structure, presence of functional groups, and 3D hyper-cross-linked network, it efficiently removed heavy metals (Cd, Cr, and Pb) from aqueous media. The effect of various parameters such as sample pH, adsorbent dosage, contact time, and adsorbate concentrations was thoroughly investigated. The experimental data were analyzed by a variety of isotherm models wherein Langmuir was found to be the best fit for explaining the adsorption of all the metals. The adsorption kinetics was best explained by the pseudo-second-order model. The maximum adsorption capacities for Cd, Cr, and Pb were 60.98 mg g-1, 119 mg g-1, and 9.302 mg g-1, respectively. The synthesized adsorbent was also tested for removal of organic dyes, and it showed selective and fast removal of Eriochrome Black T. Polymeric resins can be promising materials for adsorptive remediation of pollutants in aqueous media.

Novel thermo and ion-responsive copolymers based on metallo-base pair directed host-guest complexation for highly selective recognition of Hg2+ in aqueous solution

The development of materials with highly selective recognition towards Hg²⁺ is of great significance in environmental monitoring. Herein, a novel thermo-responsive copolymer with Hg²⁺ recognition property is prepared via thermally-initiated copolymerization of 5'-O-Acryloyl 5-methyl-uridine (APU) and N-isopropylacrylamide (NIPAM). The chemical structure and stimuli-sensitive properties of poly(N-isopropylacrylamide-co-5-methyl-uridine) (P(NIPAM-co-APU)) linear polymers and hydrogel are thoroughly investigated. At the supramolecular level, P(NIPAM-co-APU) linear polymers could respond to both temperature and Hg²⁺ stimuli with highly selective recognition towards Hg²⁺ over other 18 metal ion species (at least 5 fold difference) and common anions. Upon capturing Hg²⁺ by APU units as host metal receptors, the lower critical solution temperature (LCST) of P(NIPAM-co-APU, PNU-7 and PNU-11) linear polymers are significantly shifted more than 10 °C due to the formation of stable APU-Hg²⁺-APU directed host-guest complexes. Accordingly, at the macroscopic level, P(NIPAM-co-APU) hydrogel display selective and robust recognition of Hg²⁺ under optimum conditions, and its maximum Hg²⁺ uptake capacity was 33.1 mg g^-1. This work provides a new option for Hg²⁺ recognition with high selectivity, which could be facilely integrated with other smart systems to achieve satisfactory detection of environmental Hg²⁺.

Pterostilbene loaded poly(vinyl alcohol)-gelatin cryogels as potential bioactive wound dressing material

Cryogels are support materials which are good at mimicking extracellular matrix due to their excellent hydrophilicity, biocompatibility, and macroporous structure, thus they are useful in facilitating cell activities during healing process. In this study, polyvinyl alcohol-gelatin (PVA-Gel) based cryogel membranes loaded with pterostilbene (trans-3,5-dimethoxy-4-hydroxystilbene; PTS) (PVA-Gel/PTS) was synthesized as wound dressing materials. PVA-Gel and PVA-Gel/PTS were synthesized with the polymerization yields of 96% ± 0.23% and 98% ± 0.18%, respectively, and characterized by swelling tests, Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM) analysis. The swelling ratios were calculated as 98.6% ± 4.93% and 102% ± 5.1%, macroporosities were determined as 85% ± 2.13% and 88% ± 2.2%, for PVA-Gel and PVA-Gel/PTS, respectively. It was determined that PVA-Gel and PVA-Gel/PTS have 17 m² /g ± 0.76 m² /g and 20 m² /g ± 0.92 m² /g surface areas, respectively. SEM studies were demonstrated that they have ~100 μm pore sizes. According to 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), trypan blue exclusion and live-dead assay results, it was observed that cell proliferation, cell number and cell viability were higher in PVA-Gel/PTS cryogel at 24, 48, and 72 h compared to PVA-Gel. A strong and transparent fluorescent light intensity was observed indicating higher cell population in PVA-Gel/PTS in comparison with PVA-Gel, according to 4',6-diamidino-2-phenylindole (DAPI) staining. SEM, F-Actin, Giemsa staining and inverted-phase microscope image of fibroblasts in PVA-Gel/PTS cryogels revealed that dense fibroblast proliferation and spindle-shaped morphology of cells were preserved. Moreover, DNA agarose gel data demonstrated that PVA-Gel/PTS cryogels had no effect on DNA integrity. Consequently, produced PVA-Gel/PTS cryogel can be used as wound dressing material to promote wound therapies, inducing cell viability and proliferation.

Online column preconcentration for speciation and selective determination of Cr(III) in natural water samples using flow injection with chemiluminescence detection

A simple, rapid, sensitive and inexpensive approach is described in this work based on a combination of solid-phase extraction of 8-hydroxyquinoline (8HQ), for speciation and preconcentration of Cr(III) and Cr(VI) in river water, and the direct determination of these species using a flow injection system with chemiluminescence detection (FI-CL) and a 4-diethylamino phenyl hydrazine (DEAPH)-hydrogen peroxide system. At different pH, the two forms of chromium [Cr(III) and Cr(VI)] have different exchange capacities for 8HQ, therefore two columns were constructed; the pH of column 1 was adjusted to pH 3 for retaining Cr(III) and column 2 was adjusted to pH 1 for retaining of Cr(VI). The sorbed Cr(III) and Cr(VI) species were eluted from columns using 3.0 ml of 0.1 N of HCl and 3.0 ml of 0.1 N of NaOH, respectively. The flow injection-chemiluminescence (FI-CL) method is based on light emitted due to the oxidation of DEAPH by the H₂ O₂ in the presence of Cr(III), which catalyzes the reaction. The flow cell is a transparent coiled tube made from glass (2.0 × 4.0, inner and outer diameter) and located close to the photodetector. The flow parameters: flow rate, sample volume, flow cell length, and distance to the CL detector were studied and optimized. Under optimum flow conditions, the Cr(III) concentration can be determined over the range 5-350 μg L^-1 with a limit of detection of 1.2 μg L^-1 , as the Cr(III) concentration is proportional to the intensity of the CL signal. The relative standard deviations (%) for 10 and 50 μg L^-1 Cr(III) were 1.2% and 3.2%, respectively. The effects of Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Co(II), Cu(II), Ni(II), Mn(II), Ca(II), and Fe(III) were investigated. The proposed method is highly selective and sensitive, enabling a rapid determination of the Cr(III) amount in the presence of other interfering metals. Finally, the FI-CL method was examined in five river water samples with excellent recoveries.

Cr(III) Ion-Imprinted Hydrogel Membrane for Chromium Speciation Analysis in Water Samples

Novel Cr(III)-imprinted poly(vinyl alcohol)/sodium alginate/AuNPs hydrogel membranes (Cr(III)-IIMs) were obtained and characterized and further applied as a sorbent for chromium speciation in waters. Cr(III)-IIMs were prepared via solution blending method using blends of poly(vinyl alcohol) and sodium alginate as film-forming materials, poly(ethylene glycol) as a porogen agent, sodium alginate stabilized gold nanoparticles (SA-AuNPs) as a crosslinking and mechanically stabilizing component, and Cr(III) ions as a template species. The physicochemical characteristics of pre-synthesized AuNPs and obtained hydrogel membranes Cr(III)-IIM were studied by UV-vis and FTIR spectroscopy, TEM and SEM observations, N₂ adsorption-desorption measurements, and XRD analysis. The mechanism of the adsorption process toward Cr(III) was best described by pseudo-first-order kinetic and Langmuir models. Experiments performed showed that quantitative retention of Cr(III) is attained in 20 h at pH 6 and temperature 40 °C. Under the same conditions, the adsorption of Cr(VI) is below 5%. A simple and sensitive analytical procedure was developed for the speciation of Cr in an aquatic environment using dispersive solid phase extraction of Cr(III) by Cr(III)-IIM prior to selective Cr(VI) measurement by ETAAS in the supernatants. The detection limits and reproducibility achieved for the Cr speciation analysis fulfill the requirements for their monitoring in waters under the demand of the Water Framework Directive.

[Magnetic ion imprinting techniques for the separation and analysis of elemental speciation]

Metal and metalloid elements have various possible isotopic compositions and oxidation states and often form coordination or covalent compounds with inorganic and organic small molecules or biological macromolecules, resulting in complex elemental speciation. Different species of the same element often have different properties, which dictate their behavior. Thus, elemental speciation analysis is vital for comprehensively and accurately assessing an element's environmental and biological effects and the corresponding risks. Because elemental speciation determines the behavior of an element in different environmental and biological processes, the analysis of elemental species has, in recent years, been important in various subjects, including analytical chemistry, environmental chemistry, geochemistry, ecology, agronomy, and biomedicine. The complexity of environmental and biological sample matrices, as well as the multiformity, low levels, and lability of chemical forms pose severe challenges in elemental speciation analysis. Therefore, the highly selective identification and efficient separation of native species is necessary for conducting the identification, quantification, ecotoxicity evaluation, and physiological function study of elemental speciation. Sample pretreatment by solid-phase extraction is an effective solution to the aforementioned problems, but the existing methods do not meet the requirements of current research. The transition of the target species from pre-processing to the detection device includes both on- and off-line arrangements. Compared with the on-line approach, the off-line approach requires more manual participation, increasing the analysis workload. However, the off-line approach can improve the analysis efficiency through high-throughput pretreatment when large batches of samples are encountered, meaning the off-line approach is still an effective model. Ion imprinting technology has been developed based on existing molecular imprinting technology, with four main steps present in the synthesis of ion imprinted polymers. First, ion imprinting technology uses metal ions as templates. Then, these templates are combined with the functional monomers through coordination, electrostatic or hydrogen bonding. The functional monomers simultaneously surround and fix the templates, after which the cross-linkers and functional monomers polymerize to prepare ion-imprinted polymers with a specific structure and composition. Finally, the imprinted holes are created in the polymers by eluting the template ions. Therefore, the template molecules, functional monomers, and cross-linkers are three precursors necessary for synthesizing ion-imprinted polymers. These polymers can specifically bind to the imprinted metal ions with accuracy, sensitivity, and reliability. In recent years, they have been widely used in separating, enriching, analyzing, and detecting elemental species. During solid-phase extraction, the non-magnetic adsorbent materials dispersed in the sample solution need to be separated by centrifugation or filtration, which is time-consuming and laborious. Because an external magnetic field can be used for rapid magnetic solid-phase extraction, it has become a potential method for separating and enriching elemental species. This review systematically summarizes the latest progress in ion-imprinting technology, including its principle and the preparation methods of ion-imprinted polymers. The challenges faced by ion imprinting technology are analyzed in the context of the development of ion-imprinting magnetic solid-phase extraction in elemental speciation analysis. Finally, the direction of future development and the strategies of ion imprinting technology in elemental speciation analysis are proposed. It is important to exploit novel organic-inorganic hybrid polymerization-based multifunctional ion-imprinted magnetic nanocomposites for the magnetic solid-phase extraction and separation of elemental species. By establishing the pretreatment protocols with high recognition selectivity, strong separation ability, large adsorption capacity, and good speciation stability, we expect to achieve the research objectives of simultaneously separating and enriching the multiple-species of typical metal/metalloid elements in environmental and biological samples.

Molecularly Imprinted Affinity Membrane: A Review

A molecularly imprinted affinity membrane (MIAM) can perform separation with high selectivity due to its unique molecular recognition introduced from the molecular-printing technique. In this way, a MIAM is able to separate a specific or targeted molecule from a mixture. In addition, it is possible to achieve high selectivity while maintaining membrane permeability. Various methods have been developed to produce a MIAM with high selectivity and productivity, with their respective advantages and disadvantages. In this paper, the MIAM is reviewed comprehensively, from the fundamentals of the affinity membrane to its applications. First, the development of a MIAM and various preparation methods are presented. Then, applications of MIAMs in sensor, metal ion separation, and organic compound separation are discussed. The last part of the review discusses the outlook of MIAMs for future development.

Development of Solid Phase Extraction Method Based on Ion Imprinted Polymer for Determination of Cr(III) Ions by ETAAS in Waters

In this work, a new solid phase extraction method for the determination of chromium species in water samples by electrothermal atomic absorption spectrometry was developed. For selective separation of Cr(III) ions under dynamic conditions, two ion imprinted polymers containing Cr(III)-1,10-phenanthroline complex (Cr(III)-phen) were prepared with the use of one (styrene, ST) or two (styrene and 4-vinylpyridine, ST-4VP) functional monomers. The physicochemical properties of those solid sorbents towards Cr(III) ions were studied and compared. It was found that Cr(III) ions were retained on the Cr(III)-phen-ST and Cr(III)-phen-ST-4VP polymers with high efficiency and repeatability (91.6% and 92.9%, RSD < 2%) from solutions at pH 4.5. The quantitative recovery of the analyte (91.7% and 93.9%, RSD < 4%) was obtained with 0.1 mol/L EDTA solution. The introduction of 4VP, an additional functional monomer, improved selectivity of the Cr(III)-phen-ST-4VP polymer towards Cr(III) ions in the presence of Cu(II), Mn(II) and Fe(III) ions, and slightly decreased the sorption capacity and stability of that polymer. The accuracy of procedures based on both polymeric sorbents was proved by analyzing the standard reference material of surface water SRM 1643e. The method using the Cr(III)-phen-ST polymer was applied for determining of Cr(III) ions in tap water and infusion of a green tea.

Molecularly Imprinted Polymers for Removal of Metal Ions: An Alternative Treatment Method

Aquatic and terrestrial environment and human health have been seriously threatened with the release of metal-containing wastewater by the rapid growth in the industry. There are various methods which have been used for removal of ions from the environment, such as membrane filtration, ion exchange, membrane assisted liquid extraction and adsorption. As a sort of special innovation, a polymerization technique, namely molecular imprinting is carried out by specific identification for the target by mixing it with a functional monomer. After the polymerization occurred, the target ion can be removed with suitable methods. At the end of this process, specific cavities, namely binding sites, are able to recognize target ions selectively. However, the selectivity of the molecularly imprinted polymer is variable not only because of the type of ligand but also charge, size coordination number, and geometry of the target ion. In this review, metal ion-imprinted polymeric materials that can be applied for metal ion removal from different sources are discussed and exemplified briefly with different metal ions.

Synthesis and characterization of novel ion-imprinted guanyl-modified cellulose for selective extraction of copper ions from geological and municipality sample

The new ion-imprinted guanyl-modified cellulose (II.Gu-MC) was prepared for the separation and determination of Cu (II) ions in different real samples. Several techniques such as Fourier Transform Infrared (FT-IR), scanning electron microscope (SEM), thermal analysis, potentiograph and elemental analysis have been utilized for the characterization of II.Gu-MC. The adsorption behavior of the ion imprinted polymer (II.Gu-MC) was evaluated and compared to the non ion-imprinted polymer (NII.Gu-MC) at the optimum conditions. The selectivity and the adsorption capacity were greatly enhanced by using the ion-imprinted polymer, indicating its validation for the separation and determination of Cu²⁺ ions in different matrices. The adsorption capacity by chelating fibers II.Gu-MC & NII.Gu-MC agreed with the second-order model, and the sorption-isotherm experiments revealed best agreement with Langmuir model. The adsorption capacity of II.Gu-MC and NII.Gu-MC were 115 and 55 mg·g^-1, respectively. The II.Gu-MC was successfully employed for the selective separation and determination of Cu(II) ions with high accuracy.

Novel Imprinted Polymer for the Preconcentration of Cadmium with Determination by Inductively Coupled Plasma Mass Spectrometry

A novel Cd(II)-imprinted polymer was prepared with chemical immobilization approach by using N-methacryloyl-L-histidine as a vinylated chelating agent for on-line solid phase extraction of Cd(II) for determination by inductively coupled plasma mass spectrometry. Cd(II)-monomer complex was synthesized and copolymerized via bulk polymerization method in the presence of ethyleneglycoldimethacrylate cross-linker. The resulting polymer was leached with 1.0 mol L^-1 HNO₃ to generate the cavities in the polymer for Cd(II) ions. The experimental conditions, including load pH, solution flow rate, and eluent concentration for effective sorption of Cd(II) were optimized using a minicolumn of the imprinted polymer. A volume of 5.0 mL sample 5 μg L^-1 Cd(II) solution at pH 6.5 was loaded onto the column at 2.0 mL min^-1 by using a sequential injection system (FIALab 3200) followed by elution with 1.0 mL of 0.75 mol L^-1 HNO₃. The relative selectivity coefficients of the imprinted polymer for Cd(II) were 38.5, 3.5, 3.0, 2.5 and 6.0 in the presence of Cu(II), Ni(II), Zn(II), Co(II) and Pb(II), respectively. Computational calculations revealed that the selectivity of the imprinted polymer was mediated by the stability of Cd(II)-N-methacryloyl-L-histidine complex which was far more stable than those of commonly used monomers, such as 4-vinyl pyridine, methacrylic acid and vinylimidazole. The detection limit (3s) and relative standard deviation (%) were found to be 0.004 μg L^-1 and 3.2%, respectively. The method was validated by analysis of seawater certified reference material (CASS-4) and successfully applied to the determination of Cd(II) in coastal seawater and estuarine water samples.

Capacitive Biosensors and Molecularly Imprinted Electrodes

Capacitive biosensors belong to the group of affinity biosensors that operate by registering direct binding between the sensor surface and the target molecule. This type of biosensors measures the changes in dielectric properties and/or thickness of the dielectric layer at the electrolyte/electrode interface. Capacitive biosensors have so far been successfully used for detection of proteins, nucleotides, heavy metals, saccharides, small organic molecules and microbial cells. In recent years, the microcontact imprinting method has been used to create very sensitive and selective biorecognition cavities on surfaces of capacitive electrodes. This chapter summarizes the principle and different applications of capacitive biosensors with an emphasis on microcontact imprinting method with its recent capacitive biosensor applications.

Preparation of an ion imprinted functionalized mesoporous silica for rapid and specific absorption Cr(iii) ions in effluents

We developed an effective and selective method to remove Cr(iii) ions in acidic effluents.

Synthesis, characterization and application of ion imprinted polymeric nanobeads for highly selective preconcentration and spectrophotometric determination of Ni²⁺ ion in water samples

Here, the researchers report on the synthesis of ion imprinted polymeric (IIP) nanoparticles using a thermal polymerization strategy, and their usage for the separation of Ni(2+) ion from water samples. The prepared Ni-IIP was characterized by colorimetry, FT-IR spectroscopy, and scanning electron microscopy. It was found that the particle size of the prepared particle to be 50-70 nm in diameter with the highly selective binding capability for Ni(2+) ion, with reasonable adsorption and desorption process. After preconcentration, bound ions can be eluted with an aqueous solution of hydrochloric acid, after their complexation with dimethylglyoxime, these ions can be quantified by UV-Vis absorption spectrophotometry. The effect of various parameters on the extraction efficiency including pH of sample solution, adsorption and leaching times, initial sample volume, concentration and volume of eluent were investigated. In selectivity study, it was found that imprinting causes increased affinity of the prepared IIP toward Ni(2+) ion over other ions such as Na(+), K(+), Ag(+), Co(2+), Cu(2+), Cd(2+), Hg(2+), Pb(2+), Zn(2+), Mn(2+), Mg(2+), Cr(3+), and Fe(3+). The prepared IIP can be used and regenerated for at least eight times without any significant decrease in binding affinities. The prepared IIP is considered to be promising and selective sorbent for solid-phase extraction and preconcentration of Ni(2+) ion from different water samples.

Synthesis and application of ion-imprinted polymer for extraction and pre-concentration of iron ions in environmental water and food samples

In this work, a novel Fe(III) ion imprinted polymer as a sorbent for extraction of iron ions from different samples was synthesized. Precipitation of thermal copolymerization was used for preparation of polymeric sorbent. In this technique, methacrylic acid, ethylene glycoldimethacrylate, 2,2'-azobisisobutyronitrile and (DHBPT)2 {(DHBPT)2=3,6-bis (3,5-dimethyl-1-H-pyrzol-1-yl)-1,2-dihydro-1,2,4,5-tetrazine)} were used as monomer, cross-linker, initiator and ligand, respectively, in the presence of Fe(III) ions and ethanol as a porogenic solvent. Moreover, control polymer (NIP) particles were similarly prepared without the Fe(III) ions. XRD, FT-IR, SEM and nitrogen adsorption-desorption techniques have been used to characterization of these prepared polymeric samples. Iron ion imprinted polymer particles, abbreviated as Fe(III)-IIP, were leached with 50 mL of HCl (50% (v/v)). Absorption capacity for ion imprinted polymer was calculated about 40.41 mg·g(-1). Per-concentration of iron ion was investigated as a function of pH, weight of IIP, adsorption and desorption times, and volumes of sample. FAAS technique was used to determination of Fe(III) ion in the foods and waters samples.

Thiourea modified polyacrylnitrile fibers as efficient Pd(ii) scavengers

N-(2-Aminoethyl)thiourea functionalized polyacrylonitrile fiber was prepared and used for scavenging Pd in the synthesis of active pharmaceutical ingredients (APIs).

From imprinting to microcontact imprinting-A new tool to increase selectivity in analytical devices

Molecular imprinting technology has been successfully applied to small molecular templates but a slow progress has been made in macromolecular imprinting owing to the challenges in natural properties of macromolecules, especially proteins. In this review, the macromolecular imprinting approaches are discussed with examples from recent publications. A new molecular imprinting strategy, microcontact imprinting is highlighted with its recent applications.

Highly selective monitoring of metals by using ion-imprinted polymers

Ion imprinting technology is one of the most promising tools in separation and purification sciences because of its high selectivity, good stability, simplicity and low cost. It has been mainly used for selective removal, preconcentration, sensing and few miscellaneous fields. In this review article, recent methodologies in the synthesis of IIPs have been discussed. For several applications, different parameters of IIP including complexing and leaching agent, pH, relative selectivity coefficient, detection limit and adsorption capacity have been evaluated and an attempt has been made to generalize. Biomedical applications mostly include selective removal of toxic metals from human blood plasma and urine samples. Wastewater treatment involves selective removal of highly toxic metal ions like Hg(II), Pb(II), Cd(II), As(V), etc. Preconcentration covers recovery of economically important metal ions such as gold, silver, platinum and palladium. It also includes selective preconcentration of lanthanides and actinides. In sensing, various IIP-based sensors have been fabricated for detection of toxic metal ions. This review article includes almost all metal ions based on the ion-imprinted polymer. At the end, the future outlook section presents the discussion on the advancement, corresponding merits and the need of continued research in few specific areas. Graphical Abstract IIPs for the selective monitoring of metals.

Molecular imprinting science and technology: a survey of the literature for the years 2004-2011

Herein, we present a survey of the literature covering the development of molecular imprinting science and technology over the years 2004-2011. In total, 3779 references to the original papers, reviews, edited volumes and monographs from this period are included, along with recently identified uncited materials from prior to 2004, which were omitted in the first instalment of this series covering the years 1930-2003. In the presentation of the assembled references, a section presenting reviews and monographs covering the area is followed by sections describing fundamental aspects of molecular imprinting including the development of novel polymer formats. Thereafter, literature describing efforts to apply these polymeric materials to a range of application areas is presented. Current trends and areas of rapid development are discussed.