Adsorption of arsenate on untreated dolomite powder

Mineralogical controls on arsenite adsorption onto soils: Batch experiments and model-based quantification

The accumulation of arsenic (As) in agrarian soils poses a potential long-term risk to human health, and this accumulation largely depends on the adsorption behavior of As onto soil minerals. This study considered the adsorption of As(III) onto natural soils from the Datong Basin, focusing on the quantification of the adsorption capacities of soil minerals and further the prediction of As(III) adsorption isotherms of the bulk soils. Linear programming calculations show that Fe-bearing minerals, illite, dolomite, and soil organic matter all contribute to As(III) adsorption, on average accounting for 73.9, 11.4, 8.2, and 6.5% of the overall adsorption capacity of soil to As(III), respectively. However, not all the Fe-bearing minerals in soils can adsorb As(III). Evidence from the sequential chemical extractions shows that 90.1% of the soil Fe is associated with silicates (Fe_Si), while results of the linear programming calculations suggest that Fe_Si cannot adsorb As(III). Based on the above results, a surface complexation model well predicts the experimental As(III) adsorption isotherms for aeolian and riverine soils. However, the adsorption of As(III) onto lacustrine soils is underestimated in both linear programming calculations and surface complexation modeling. This study highlights the importance of both Fe-bearing minerals and non-Fe minerals for As(III) adsorption and the difference in the adsorption capacity between various soil minerals. It further suggests that more comprehensive considerations are necessary when building a reactive transport model for As(III) in soil systems.

Solid-phase partitioning and release-retention mechanisms of copper, lead, zinc and arsenic in soils impacted by artisanal and small-scale gold mining (ASGM) activities

Artisanal and small-scale gold mining (ASGM) operations are major contributors to the Philippines' annual gold (Au) output (at least 60%). Unfortunately, these ASGM activities lacked adequate tailings management strategies, so contamination of the environment is prevalent. In this study, soil contamination with copper (Cu), lead (Pb), zinc (Zn) and arsenic (As) due to ASGM activities in Nabunturan, Davao de Oro, Philippines was investigated. The results showed that ASGM-impacted soils had Cu, Pb, Zn and As up to 3.6, 83, 73 and 68 times higher than background levels, respectively and were classified as 'extremely' polluted (CD = 30-228; PLI = 5.5-34.8). Minerals typically found in porphyry copper-gold ores like pyrite, chalcopyrite, malachite, galena, sphalerite and goethite were identified by XRD and SEM-EDS analyses. Furthermore, sequential extraction results indicate substantial Cu (up to 90%), Pb (up to 50%), Zn (up to 65%) and As (up to 48%) partitioned with strongly adsorbed, weak acid soluble, reducible and oxidisable fractions, which are considered as 'geochemically mobile' phases in the environment. Although very high Pb and Zn were found in ASGM-impacted soils, they were relatively immobile under oxidising conditions around pH 8.5 because of their retention via adsorption to hydrous ferric oxides (HFOs), montmorillonite and kaolinite. In contrast, Cu and As release from the historic ASGM site samples exceeded the environmental limits for Class A and Class C effluents, which could be attributed to the removal of calcite and dolomite by weathering. The enhanced desorption of As at around pH 8.5 also likely contributed to its release from these soils.

Performance of thermally activated dolomite for the treatment of Ni and Zn in contaminated neutral drainage

Intensive research is ongoing for developing low-cost and highly efficient materials in metal removal from contaminated effluents. The present study evaluated dolomite [CaMg(CO3)2], both raw and modified by thermal activation (charring), for Ni and Zn treatment in contaminated neutral drainage (CND). Batch adsorption testing (equilibrium and kinetics) were conducted at pH 6, to evaluate the performance of initial vs. modified dolomite, and to assess potential mechanisms of metal removal. Charring of dolomite led to a rigid and porous material, mainly consisting of CaCO3 and MgO, which showed a sorption capacity increased sevenfold for Zn and doubled for Ni, relative to the raw material. In addition, Freundlich model best described the sorption of the both metals by dolomite, whereas the Langmuir model best described their sorption on charred dolomite. Plausible mechanisms of metal removal include cation exchange, surface precipitation and sorption processes, with carbonate ions and magnesium oxides acting as active centers. Based on these results, charred dolomite seems a promising option for the efficient treatment of Ni and Zn in CND.