Effect of method of crystallization on the IV-III and IV-II polymorphic transitions of ammonium nitrate

Cu-Containing Faujasite-Type Zeolite as an Additive in Eco-Friendly Energetic Materials

Regarding the current state of the art on the utilization of zeolites in industry, the application of zeolites as an additive to eco-friendly energetic materials indicates the innovative character of the present research. One of the most commonly used energetic materials in the mining industry (engineering works) is ANFO (ammonium nitrate fuel oil), due to its easy and cheap production procedure as well as its good energetic properties and vast possibilities for modification. In the present research, we investigated Cu-zeolite with a faujasite structure (Cu-FAU) as a modifier of ANFO-based energetic materials. Analysis of the results obtained from thermodynamic calculations of energetic performance led to the conclusion that the application of Cu-faujasite as an additive to ANFO resulted in a relevant reduction in the total emission of post-decomposition fumes, with simultaneous enhancement of the energetic properties of the energetic material, which corresponded with the changes in the status of the surface and the reduced thermal effect accompanying the ammonium nitrate's decomposition. From analysis of both the energetic performance and fumes, it may be concluded that our eco-friendly and enhanced energetic material can be used as a low-emission source of energy for the quarrying of raw materials.

Standoff Deep Ultraviolet Raman Spectrometer for Trace Detection

We developed a state-of-the-art, high-sensitivity, low-stray-light standoff deep-ultraviolet (DUV) Raman spectrometer for the trace detection of resonance Raman-enhanced chemical species. As an excitation source for Raman measurements, we utilized our recently developed, second-generation, miniaturized, diode-pumped, solid-state neodymium-doped gadolinium orthovanadate (Nd:GdVO4) laser that generates quasi-continuous wave 228 nm light. This 228 nm excitation enhances the Raman intensities of vibrations of NOx groups in explosive molecules, aromatic groups in biological molecules, and various aromatic hydrocarbons. Our DUV Raman spectrograph utilizes a custom DUV f/8 Cassegrain telescope with an ∼200 mm diameter primary mirror, high-efficiency DUV transmission gratings, custom DUV mirrors, and a custom 228 nm Rayleigh rejection filter. We utilized our new standoff DUV Raman spectrometer to measure high signal-to-noise ratio spectra of ∼50 μg/cm2 drop-cast explosives: ammonium nitrate (AN), trinitrotoluene, pentaerythritol tetranitrate as well as aromatic biological molecules: lysozyme, tryptophan, tyrosine, deoxycytidine monophosphate, deoxyadenosine monophosphate at an ∼3 m distance within 10-30 s accumulation times. We roughly estimate the average ultraviolet resonance Raman (UVRR) detection limits for the relatively homogeneous drop-cast films of explosives and biological molecules to be ∼1 μg/cm2 when utilizing a continuous raster scanning that averages Raman signal over ∼1 cm2 sample area to avoid quick analyte depletion due to ultraviolet (UV) photolysis. We determined 3 m standoff UVRR detection limits for drop-cast AN films and identified factors impacting UVRR detection limits such as analyte photochemistry and analyte morphology. We found a detection limit of ∼0.5 μg/cm2 for drop-cast AN films on glass substrates when the Raman signal is averaged over ∼0.5 cm2 of sample surface using a continuous raster scan. For a step raster scan, when the probed sample area is limited to the laser spot size, the detection limit is approximately tenfold higher (∼5 μg/cm2) due to the impact of UV photochemistry.

Variously Prepared Zeolite Y as a Modifier of ANFO

In the presented research, we investigated Ammonium Nitrate Fuel Oil (ANFO), with the addition of variously modified zeolite Y as an attractive explosive. Analysis of both blasting tests and thermodynamic models of blasting properties led to the conclusion that the addition of zeolite Y enhanced the detonation properties of such prepared ANFO via the growth of the detonation pressure, temperature, compression energy, and heat of the explosion. Generally, the modification of ANFO with variously prepared zeolite Y also reduced the volume of (CO_x + NO_x) post-blast fumes. Furthermore, it was found that the ANFO's velocity of detonation (VOD) could be controlled by the choice of the way of zeolite Y modification. Namely, for zeolite Y without Mg, as well as Mg-Y prepared via the impregnation method, the VOD rose. The opposite effect was observed when ANFO was modified with Mg-Y, obtained from the deposition of Mg over zeolite Y via the ultrasonic-assisted procedure.

Perspectives in the stability of emulsion explosive

This review explores the stability of emulsion explosive, through summarizing its instability reason, stability mechanism, affecting factors, improvement ways and evaluation methods. The emulsion explosive can be recognized as highly concentrated emulsion due to the volume fraction of dispersed phase exceed 74%. The polydispersity, deformation of compassed droplets and the high content of AN in dispersed phase should be considered for the stability of emulsion explosive. The coalescence is one of the important factor for the instability of emulsion explosive as the droplets bound to each other tightly, together with that, the crystallization of AN in dispersed droplets will occur. This process will further decrease the stability of emulsion explosive. Interfacial tension, the strength of interfacial film and electrical properties of droplets are the important mechanism for preparation and stability of emulsion explosive, among the three, the effect of the strength of interfacial film is most important, and the greater the strength of the interfacial film, the more stable the emulsion explosive. The stability of emulsion explosive will be affected by the emulsifier's structure, the viscosity and polarity of oil, the crystallization point of AN and the nature of matrix, in which, it is important to pay attention to the influence of emulsifier structure because adjusting emulsifier structure is a key channel to improve the stability of emulsion explosive. Besides that, the targeted methods to improve the stability of different emulsion explosive, such as bulk emulsion explosive, packaged emulsion explosive and powdery emulsion explosive, were concluded and established. Finally, we proposed some effective methods for evaluating and predicting stability of emulsion explosive. These results will facilitate the further development of the researches in the mechanism and improvement approach of stability, as well as it will also provide effective technical support for exploring the stability of other similar highly concentrated emulsions.

Application of Silicon Dioxide as the Inert Component or Oxide Component Enhancer in ANFO

Non-ideal explosives with differing contents of silicon dioxide (silica or dioxosilane) added in the form of powder and gel were tested. Measurements of structure, crystallinity and morphology were performed by means of infrared spectroscopy (IR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). IR and XRD analysis revealed a lack of SiO2 influence on the non-ideal explosive structure. SEM analysis indicated that all the surface deformations of ammonium nitrate(V) prill were filled by a thin fuel film layer on which SiO2 was present. The additional calculations of selected theoretical properties of non-ideal compositions were made using ZMWCyw software. Based on this, it was established that the optimum semimetal content was 1.0 wt.%. Blasting tests confirmed that the addition of 1.0 wt.% SiO2 to the Ammonium Nitrate Fuel Oil (ANFO) resulted in the lowest volume of post-blast fumes. Moreover, it was established that finer SiO2 powder cannot be used as the oxide component enhancer due to the inhibition of detonation reaction. SiO2 should be used only as an inert component.

On the Influence of the Ammonium Nitrate(V) Provenance on Its Usefulness for the Manufacture of ANFO Type Explosives

Ammonium nitrate fuel oil (ANFO) samples based on fertilizer (AN-F) and ammonium nitrate porous prill (AN-PP) were studied. Tests were carried out using both a thermogravimetric analyzer and differential scanning calorimetry (TGA/DSC). Furthermore, the scanning electron microscopy analysis (SEM) of ammonium nitrate(V) (AN) concerning either their surface or cross-section was performed. Based on the SEM results, it was shown that the surface of AN-F grains was flat and slightly deformed, while the AN-PP surface was wrinkled and deformed. Furthermore, the various steps of thermogravimetric process exhibited continuous AN phase transition according to precise temperatures. From TGA analysis, a significant mass loss was found as a result of ANFO decomposition. Direct comparison of SEM and TGA/DCS data led to the conclusion that ANFO based on AN-F was characterized by lower absorption of FO in contrast to AN-PP.

On the Investigation of Microstructured Charcoal as an ANFO Blasting Enhancer

In this study, we examined the influence of microstructured charcoal (MC) when added to ammonium nitrate fuel oil (ANFO) samples. We performed a study that investigated ANFOs structure, crystallinity, and morphology by utilizing infrared spectroscopy (IR), X-ray diffraction (XRD), and scanning electron microscopy (SEM), respectively. MC characteristics were probed by Raman spectroscopy and SEM analysis. SEM analysis indicated how fuel oil (FO) covered ammonium nitrate prill. Moreover, the surface of the MC was covered by specific microfibers and microtubes. The disordered graphitic structure of the MC was also confirmed by Raman spectroscopy. Simulation of blasting properties revealed that the addition of MC should decrease blasting parameters like heat explosion, detonation pressure, and detonation temperature. However, the obtained differences are negligible in comparison with the regular ANFO. All analyses indicated that MC was a good candidate as an additive to ANFO.

Influence of the Ammonium Nitrate(V) Porous Prill Assortments and Absorption Index on Ammonium Nitrate Fuel Oil Blasting Properties

Ammonium nitrate fuel oil (ANFO) samples, which were obtained by blending two different types of ammonium nitrate porous prills (i.e., AN-PP7 and AN-PP8) with fuel oil (FO) were studied. Measurements of structure, crystallinity and morphology were performed using X-ray Diffraction (XRD), Infrared Spectroscopy (IR) and Scanning Electron Microscopy (SEM), respectively. From the SEM analysis, it was indicated that a “wrinkled” structure characterized the crystal surface of the samples, which were based on two types of ammonium nitrate porous prill. Thermogravimetric analysis and differential scanning calorimetry (TGA/DSC) confirmed that AN-PP7 had a higher absorption index in comparison to AN-PP8. Furthermore, it was shown that continuous AN phase transformations at precise temperatures took place. From the blasting test, it was indicated that the absorption index only had an influence on the content of toxic fumes. However, the velocity of detonation (VOD) depended solely on the ANFO density as well as the total volume of post-blast fumes.

Surface-enhanced Raman scattering detection of ammonium nitrate samples fabricated using drop-on-demand inkjet technology

The United States Army and the first responder community are increasingly focusing efforts on energetic materials detection and identification. Main hazards encountered in theater include homemade explosives and improvised explosive devices, in part fabricated from simple components like ammonium nitrate (AN). In order to accurately detect and identify these unknowns (energetic or benign), fielded detection systems must be accurately trained using well-understood universal testing substrates. These training substrates must contain target species at known concentrations and recognized polymorphic phases. Ammonium nitrate is an explosive precursor material that demonstrates several different polymorphic phases dependent upon how the material is deposited onto testing substrates. In this paper, known concentrations of AN were uniformly deposited onto commercially available surface-enhanced Raman scattering (SERS) substrates using a drop-on-demand inkjet printing system. The phase changes observed after the deposition of AN under several solvent conditions are investigated. Characteristics of the collected SERS spectra of AN are discussed, and it is demonstrated that an understanding of the exact nature of the AN samples deposited will result in an increased ability to accurately and reliably "train" hazard detection systems.

Anatase-brookite mixed phase nano TiO2 catalyzed homolytic decomposition of ammonium nitrate

Compared to the conventional ammonium perchlorate based solid rocket propellants, burning of ammonium nitrate (AN) based propellants produce environmentally innocuous combustion gases. Application of AN as propellant oxidizer is restricted due to low reactivity and low energetics besides its near room temperature polymorphic phase transition. In the present study, anatase-brookite mixed phase TiO(2) nanoparticles (~ 10 nm) are synthesized and used as catalyst to enhance the reactivity of the environmental friendly propellant oxidizer ammonium nitrate. The activation energy required for the decomposition reactions, computed by differential and non-linear integral isoconversional methods are used to establish the catalytic activity. Presumably, the removal of NH(3) and H(2)O, known inhibitors of ammonium nitrate decomposition reaction, due to the surface reactions on active surface of TiO(2) changes the decomposition pathway and thereby the reactivity.