Rapid removal of cobalt ion from aqueous solutions by almond green hull

Ultrasensitive and highly selective detection of nickel ion by two novel optical sensors

Novel optical sensors for nickel determination by incorporation of 5-(2`-bromo-phenylazo)-6-hydroxypyrimidine-2,4-dione (I), 5-(2`,4`-dimethylphenylazo)-6-hydroxypyrimidine-2,4-dione (II), dibutylphthalate (DBP) and sodium tetra-phenylborate (Na-TPB) to the plasticized polyvinyl chloride matrices were prepared. The introduction of DBP in the membrane substantially increased the ability of both ionophores I and II to function as chromo ionophores. The advantages of the reported sensors include great stability, reproducibility, and relatively long lifespan, as well as excellent selectivity for Ni2+ ion detection across a wide range of alkali, alkaline earth, transition, and heavy metal ions.Under optimized membrane compositions and experimental parameters, the response of both sensors was linear throughout a concentration range of 3.5 × 10-8 to 8.1 × 10-5 and 2.0 × 10-8 to 5.1 × 10-5 M for I and II, respectively. Sensor detection and quantification limits based on the definition that the concentration of the sample leads to a signal equal to the blank signal plus three and ten times its standard deviation were determined to be 1.15 × 10-8 and 3.45 × 10-8 M when utilizing I, whereas they were 0.61 × 10-8 and 1.95 × 10-8 M when utilizing II, respectively. The reaction time of optodes is defined as the period required achieving 95% of based sensors and found to be 8.0 and 5.0 min using I and II, respectively. Ni2+ ion concentrations in water, food, and environmental samples were effectively determined using the proposed optical sensors. Representative diagram for preparation of the sensing Ni2+ sensor.

Eco-Friendly Recycling of Lithium Batteries for Extraction of High-Purity Metals

The significant increase in lithium batteries consumption produces a significant quantity of discarded lithium-ion batteries (LIBs). On the one hand, the shortage of high-grade ores leads to the necessity of processing low-grade ores, which contain a low percentage of valuable metals in comparison to the discarded LIBs that contain a high percentage of these metals, which enhances the processing of the discarded LIBs. On the other hand, the processing of discarded LIBs reduces the negative environmental effects that result from their storage and the harmful elements contained in their composition. Hence, the current study aims at developing cost-effective and ecofriendly technology for cobalt and lithium metal ion recovery based on discarded LIBs. A novel synthesized solid-phase adsorbent (TZAB) was utilized for the selective removal of cobalt from synthetic solutions and spent LIBs. The synthesized TZAB adsorbent was characterized by using 13C-NMR, GC-MS, FT-IR, 1H-NMR, and TGA. The factors affecting the adsorption of cobalt and lithium ions from synthetic solutions and spent LIBs, including the sorbent dose, pH, contact time, temperature, and cobalt concentration were investigated. The conditions surrounding the recovery of cobalt and lithium from processing discarded LIBs, were investigated to optimize the maximum recovery. The Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to study the kinetics of the adsorption process. The obtained results showed that high-purity CoC₂O₄ and Li₃PO₄ were obtained with a purity of 95% and 98.3% and a percent recovery of 93.48% and 95.76%, respectively. The maximum recovery of Co(II) from synthetic solutions was obtained at C₀ = 500 mg·L^-1, dose of 0.08 g, pH 7.5, T = 25 °C, and reaction time = 90 min. The collected data from Langmuir's isotherm and the adsorption processes of Co agree with the data predicted by the D-R isotherm models, which shows that the adsorption of Co(II) onto the TZAB seems to be chemisorption, and the results agree with the Langmuir and D-R isotherm models.

Intensification of strontium (II) ion biosorption on Sargassum sp via response surface methodology

A batch system was employed to investigate the biosorption of strontium (II) on Sargassum sp. The biosorption of strontium on Sargassum sp was studied with response surface methodology to determine the combined effect of temperature, initial metal ion concentration, biomass treatment, biosorbent dosage and pH. Under optimal conditions, the algae's biosorption capacity for strontium (initial pH 7.2, initial strontium concentration 300 mg/l for Mg-treated biomass and biosorbent dosage 0.1 g in 100 mL metal solution) was measured at 103.95 mg/g. In our analysis, equilibrium data were fitted to Langmuir and Freundlich isotherms. Results show that the best fit is provided by the Freundlich model. Biosorption dynamics analysis of the experimental data indicated that strontium (II) was absorbed into algal biomass in accordance with the pseudo-second-order kinetics model well.

A review of the application of fungi as an effective and attractive bio-adsorbent for biosorption of heavy metals from wastewater

One of the most hazardous environmental pollutants is the pollution risen by heavy metal ions in effluents, which is increasing due to the increasing human activity and the development of urbanization. Notwithstanding the economic challenges to control the pollution of effluent treatment processes, it seems necessary to provide effective approaches. The sorption method is widely used due to low-cost, flexibility in design and operation, repeatability, and significant performance. Hence, the need for more environmentally friendly sorbents to eliminate metal ions is greater than ever. Due to the unique features such as the presence of chitin and chitosan in the cell wall, high absorption capacity, environmental friendliness, availability, and cheapness, the use of fungi as adsorbent has received much attention. Therefore, this work tries to address the use of fungi as biosorbents to remove these metals, the dangers of heavy metals, and their sources. Moreover, equilibrium, kinetic, and thermodynamic behaviors of the heavy metal ion adsorption process in the literature are briefly studied.

Polymeric Biomass Derived Adsorbents for Co(II) Remediation, Recycling and Analysis

The gradual replacement of conventional materials with materials tailored to the green development goals is one of the needs of the day. Correspondingly, this article reviews and integrates, for the first time, the gathered knowledge on the use of the adsorbents based on polymeric biomasses (biosorbents) for a cleaner separation of cobalt (Co) from synthetic and actual solutions. It is a two-part comprehensive approach that debates the Co biosorption potential of bio-based polymers from the perspective of their virtual and real applications for decontamination, recovery, and analytical purposes. First, the removal performances of these materials to batch and fixed column biosorption of Co(II) from mono-component and multi-metallic laboratory solutions are systematized and discussed. Following that, the focus of the first part is shifted to the analytical capabilities of the biosorbents proposed for Co(II) quantification from synthetic solutions. The second section considers the polymeric biomasses successfully incorporated in practical strategies for the removal and recovery of Co(II) from real solutions. The opportunities provided by the use of biosorbents for the development of accurate and greener procedures in Co(II) analysis are also highlighted. The directions in which the research on this topic should be continued and strengthened are suggested.

Heavy metal ion detection using green precursor derived carbon dots

The discovery of carbon dots (CDs) for environmental remediation has gained awareness because of the diverse economically viable and environmental friendly green precursors generated from biowastes and biomass compared to the toxic inorganic quantum dots and CDs prepared from chemical precursors. This review presents the recent progress in green CDs, including their synthesis methods and sensing applications for the detection of heavy metal ions such as Iron (III), Mercury (II), Copper (II), Chromium (VI), Lead (II), Arsenic (III), Cobalt (II), Aluminum (III), Silver (I), and Gold (III) which are prominent environmental pollutants. The comparison based on selectivity, sensitivity, quantum yield, detection limit, linear concentration range, and sensing mechanisms are also reported. This review also covers the performance of doped green CDs using heteroatoms, toward the detection of heavy metal ions. Apart from the future perspectives, this review provides a general guide to use such environmental friendly CDs to detect harmful pollutants.

A new “on–off–on” g-C3N4 nanosheets fluorescent sensor for 5-Br-PADAP and Co2+ under acidic conditions

A novel “on–off–on” g-C3N4 nanosheet fluorescent sensor based on IFE could detect 5-Br-PADAP and Co2+ under acidic conditions.

Facile and High-yield Synthesis of N-doped Carbon Quantum Dots from Biomass Quinoa Saponin for the Detection of Co2

Hydrothermal synthesis of carbon quantum dots (CQDs) from natural biomass is a green and sustainable route for CQDs applications in various fields. In this work, the preparation and characterization of CQDs based on quinoa saponin were investigated. The optimum synthetic conditions determined by orthogonal experiments were as follows: 2 g quinoa saponin powder and 0.04 mol ethylenediamine reacted at 200°C for 10 h. The relative fluorescence quantum yield (QY = 22.2%) can be obtained, which is higher than some results reported in the literatures. The prepared CQDs had a small and uniform size (∼2.25 nm) and exhibited excitation wavelength-dependent blue light emission behavior. The CQDs displayed excellent sensitivity for Co²⁺ detection along with good linear correlation ranging from 20 to 150 µM and the detection limit of 0.49 µM. The CQDs prepared in this experiment were successfully implanted into soybean sprouts for fluorescence imaging. The sprouts could grow healthily even soaked in the CQDs solution for two weeks, demonstrating the low toxicity of the CQDs. The advantages of the CQDs, such as low cost, ease of manufacture, nontoxicity, and stability, have potential applications in many areas such as metal ion detection and biosensing.

A Novel Imidazole Bound Schiff Base as Highly Selective "Turn-on" Fluorescence Sensor for Zn2+ and Colorimetric Kit for Co2

An imidazole based Schiff base (2-[(1H-imidazole-2-ylmethylene)-amino]-4-methyl-phenol) (IMP), with an imine unit, has been designed and characterized by various standard methods. The evaluation of the probe as a fluorogenic sensor for Zn²⁺ and a chromogenic sensor for Co²⁺ has been rationalized in terms of the PET mechanism. In the presence of Zn²⁺, a light yellow colored solution of IMP with maximum absorption of 364 nm becomes bright yellow with maximum absorption of 410 nm and a measurable fluorescent signal at 612 nm with bathochromic enhancement. The sensitivity of the fluorescent based assay (6.78 × 10^-9 M) for Zn²⁺ is far below the limit in the World Health Organization (WHO) guidelines for drinking water (7.6 × 10^-5 M) and therefore it is capable of being a practical system for the monitoring of Zn²⁺ concentrations in aqueous samples. Moreover, IMP showed a highly selective colorimetric response to Co²⁺ by displayed an obvious pink color upon addition of metal solution immediately without any interference from other ions. These results provide a new approach for selectively recognizing the two most important trace elements in the human body simultaneously, for Zn²⁺ by emission spectra and Co²⁺ by the naked eye.

Recovery and recycle of wastewater contaminated with heavy metals using adsorbents incorporated from waste resources and nanomaterials-A review

Recovery and recycle of wastewater are essential because of the need of huge quantities of water everywhere in this world. Presence of heavy metals in wastewater such as iron (Fe), molybdenum (Mo), manganese (Mn), zinc (Zn), nickel (Ni), copper (Cu), vanadium (V), cobalt (Co), tungsten (W), chromium (Cr), arsenic (As), silver (Ag), antimony (Sb), cadmium (Cd), mercury (Hg), lead (Pd), uranium (U), etc is the serious environmental issues and risk for human and animal health. Adsorbents are simple and low-cost methods to treat the pollutants and heavy metals of wastewater. The adsorbents are capable to treat the wastewater prepared from different wastes such as domestic, agricultural, industrial, animal and marine waste etc. In recent years, novel nanomaterials are also used as adsorbents which enhance the treatment efficiency of wastewater. Adsorption is a mass transfer phenomenon revolving shift of elements from a fluid to a solid phase based on the concentration gradient. The mechanism which helps in separation of contaminants from the effluent and the factors governing the efficiency of adsorption are discussed elaborately.

Efficient adsorptive removal of Cobalt(II) ions from water by dicalcium phosphate dihydrate

Although the radionuclide ⁶⁰Co is widely used, its presence in various effluents demands its removal to preclude environmental pollution and detrimental effects on human health. This study investigated the batch adsorption performance of a potential cobalt adsorbent, dicalcium phosphate dihydrate (DCPD), in immobilizing Co²⁺ from water. The influences of solution pH, contact time, initial concentration, and competing cations were examined and discussed. Stable cobalt uptake was observed at pH 4-8. The sorption kinetics showed a multi-stage uptake profile, implying that several mechanisms are involved in the adsorption process. Microscopy and structural analysis revealed that DCPD decomposes to its anhydrous form during adsorption, which explains the multistep curve over the entire adsorption period. However, the non-apatitic transformation is not exclusive to cobalt uptake. Intraparticle diffusion also contributed to the overall removal kinetics of Co²⁺ from water. Considering the Sips isotherm model, the maximum Co²⁺ adsorption capacity of DCPD was 441 mg g^-1. Cobalt uptake selectivity dropped in the presence of Ca²⁺ ions, from 1.21 × 10⁴ to 207 mL g^-1, indicating DCPD would be more applicable in treating soft ⁶⁰Co-contaminated waters. Structural analysis, elemental mapping, and qualitative analysis of solid residues confirmed that ion exchange is involved in the removal of cobalt from aqueous solutions.

Removal of Cd(II) using dithiocarboxyl cornstalk and the waste filtrate

A novel adsorbent, called dithiocarboxyl cornstalk (DTCS), was developed, and the effects of various parameters on the adsorption performance for Cd(II) with DTCS were investigated in this work. The results suggested that DTCS presented the efficient removal capacity for Cd(II) when the pH values, adsorption temperature, and oscillation rate were 3.0 to 6.0, 313 K, and 150 rpm, respectively. The adsorption kinetic data were more agreed with pseudo-second-order kinetic model, and the isotherm data could be characterized by Freundlich model. The thermodynamic data indicated the adsorption process was endothermic and spontaneous. The FTIR and SEM confirmed the chemisorption between Cd(II) and DTCS. Furthermore, to eliminate the secondary pollution, the waste filtrate generated in the preparation of DTCS was employed to remove Cd(II) through flocculation experiments. The results showed that the waste filtrate is a potential flocculant for the treatment of wastewater containing Cd(II).

Sorption behavior and mechanism of oxytetracycline from simulated wastewater by Amberlite IR-120 resin

The adsorption of oxytetracycline from aqueous solution by the resin Amberlite IR 120 was studied. The effect of different experimental parameters such as contact time, initial concentration of OTC 40-200 mg/l, initial pH 2-12 of aqueous solution, adsorbent dose 0.5-3 g/l, and stirring speed 100-700 rpm on the adsorption of OTC were investigated. The kinetic adsorption experimental results were analyzed using pseudo-first order, pseudo-second order and Elovich kinetic models. The adsorption process was found to follow a pseudo-second order kinetic model and the corresponding rate constants were obtained. A film-pore diffusion (FPD) mass transfer model has been developed to predict the concentration distribution in the fluid phase, based on the external mass transfer coefficient and the effective diffusion coefficient. The values of the external mass transfer coefficient (β_L) and effective diffusion coefficient (D_eff) were found to decrease with increasing OTC concentration. The comparison between the experimental and the theoretical curves allowed us to note that the film-pore diffusion mass transfer model gave a good agreement with the experimental data for all the values of initial OTC concentration.

Biosorption of Co2+ Ions from Aqueous Solution by K2HPO4-Pretreated Duckweed Lemna gibba

The wastewater of the many industries that use divalent cobalt (Co2+)-containing compounds has elevated levels of this metal. Thus, novel technology is needed to efficiently remove Co2+ ions from aqueous solutions. Biosorption is a low-cost technique capable of removing heavy metals from contaminated water. This study aims to evaluate the performance of KH2PO4-pretreated Lemna gibba (PLEM) as a biosorbent of Co2+ in aqueous solutions tested under different conditions of pH, particle size, and initial Co2+ concentration. Kinetic, equilibrium, and thermodynamic studies were conducted. The capacity of biosorption increased with a greater initial Co2+ concentration and was optimal at pH 7.0 and with small-sized biosorbent particles (0.3–0.8 mm). The pseudo-second-order sorption model best describes the experimental data on Co2+ biosorption kinetics. The Sips and Redlich-Peterson isotherm models best predict the biosorption capacity at equilibrium. According to the thermodynamic study, biosorption of Co2+ was endothermic and spontaneous. The effect of pH on the biosorption/desorption of Co2+ suggests that electrostatic attraction is the main biosorption mechanism. SEM-EDX verified the presence of Co2+ on the surface of the pretreated-saturated biosorbent and the absence of the metal after desorption.

Sorption capacity of seaweed-like sodium titanate mats for Co2+ removal

The development of new technologies for securing and recycling water resources are in high demand. A key focus of these technologies is the development of various ion exchangers or adsorbents that are used for the purification of aqueous solutions. Layered sodium titanate is one of the cation exchangers utilised in the removal of heavy metals and radionuclides from wastewater. To enhance the removal efficiency, the precise design of the crystal morphology, structure, and chemical composition is important. Herein, we synthesised a unique seaweed-like sodium titanate mat (SST) using a template-free alkaline hydrothermal process. The Co²⁺ sorption capacity of SST was investigated by batch testing with cobalt(ii) nitrate. SST, which was synthesised from titanium sulphate in a 10 M NaOH solution at 200 °C, had a seaweed-like structure composed of randomly distributed nanofibres of layered sodium titanate that is approximately 9 nm in diameter. The crystal shape changed from roundish crystals to fibrous crystals as the hydrothermal reaction period increased. The Co²⁺ sorption isotherm of SST was fitted with the Langmuir isotherm model and the maximum sorption density was 1.85 mmol g⁻¹. The selectivity of the Co²⁺ sorption on SST was high in comparison to that of Ca²⁺ and Mg²⁺. Herein, the Co²⁺ sorption mechanisms of SST were studied in comparison with commercially available sodium titanate. Results show that controlling the crystal morphology, structure, and Na concentration of the layered titanate that can be ion-exchanged determines the cation sorption properties of sodium titanate.

The seaweed-like sodium titanate mat has a high Co²⁺ sorption capacity via the ion-exchange reaction due to its crystal structure, low crystallinity, and morphology.

Valorization of Eggshell Biowaste for Sustainable Environmental Remediation

The management of large amounts of eggshell waste annually produced in the world is problematic as generally this material is only disposed at landfills with odor production and microbial growth. On the contrary, significant environmental and economic advantages could be obtained transforming this biowaste into new value-added products. Eggshell biowaste was the starting material for the synthesis of hydroxyapatite by a simple and sustainable procedure and applied for the removal of Co²⁺ from aqueous solutions. The effects of contact time and initial metal concentration were investigated in batch experiments. Eggshell-based hydroxyapatite (ESHAP) before and after Co²⁺ removal was characterized by X-ray diffraction and scanning electron microscopy. The process was rapid and reached equilibrium within 80 min. The removal efficiency was in the range 70-80% which is generally higher than other waste-derived adsorbents. Adsorption of Co²⁺ on the surface of ESHAP particles and ion exchange with Ca²⁺ resulting in the formation of a Co-phosphate are the main mechanisms of the metal removal. The conversion of eggshell waste to a low-cost adsorbent for the treatment of metal contaminated waters could contribute to a more sustainable and effective management of this biowaste.

Immobilization of radioactive corrosion products by cold sintering of pure hydroxyapatite

An efficient method for the consolidation of cobalt (Co(II)) adsorbed calcium hydroxyapatite was investigated to develop a simplified route for decontamination of the coolant system of nuclear power plants and direct immobilization of as-spent adsorbent. Calcium hydroxyapatite nano-powder synthesized by a wet precipitation method was used as an adsorbent and 94% Co(II) surrogate removal from simulated water was measured. The as-spent adsorbent was sintered at 200 °C, a temperature significantly lower than conventional sintering temperatures (900-1300 °C) for hydroxyapatite, under a uniaxial pressure of 500 MPa for 10 min. The relative density after the cold sintering was >97% and sintered samples displayed good compressive strength (175 MPa). The normalized leaching rate of the Co(II) was measured as per ASTM-C1285 standard and found to be 2.5 × 10^-5 g/m²/day. ANSI/ANS-16.1 test procedure was used to analyze the leachability of the sintered matrices and the measured leaching index value was 6.5. Thus, the use of pure calcium hydroxyapatite nano-powder as adsorbent and its cold sintering offers a mean by which radioactive waste form can be processed in an environment friendly manner.

Treatment of mining waste leachate by the adsorption process using spent coffee grounds

The removal of heavy metals from mining waste leachate by spent coffee grounds has been investigated. In synthetic solutions, metal uptake was studied in batch adsorption experiments as a function of pH, contact time, initial metal concentration, adsorbent concentration, particle size, and the effect of co-ions (Na, K, Ca, Mg, Cu, Cd, Ni, Zn). Results showed that adsorption was significantly affected by pH, showing the highest affinity within a pH range of 5-7. Sorption of heavy metals reached equilibrium in 3 h. Removal percentages of metals ions increased with increasing dosage. Particle size did not have a significant influence on metal uptake. The adsorption of heavy metals was found to fit Langmuir and Freundlich isotherms. Maximum Zn, Cd and Ni uptake values were calculated as 10.22, 5.96 and 7.51 mg/g, respectively, using unwashed coffee grounds (UCG) as the adsorbent and 5.36, 4.28 and 4.37 mg/g when employing washed coffee grounds as the adsorbent. The presence of co-ions inhibited the uptake of heavy metals, divalent ions having a more negative effect than monovalent ions. The results obtained in the experiments with mining waste leachate showed that UCG is effective in removing heavy metals.

Calcined Umbonium vestiarium snail shell as an efficient adsorbent for treatment of wastewater containing Co (II)

In the present study, the Umbonium vestiarium snail shell (UVS) was used as an abundant and low-cost resource for the removal of Co (II) from aqueous solution. The characteristics of calcined Umbonium vestiarium snail shell (CUVS) were analyzed using FTIR, SEM, MAP, EDAX, and BET analyses. The results showed that the specific surface area of the CUVS was obtained 17.02 m2/g which was an acceptable amount. The presence of Co (II) in the adsorbent structure was confirmed by EDAX, and Map analyses after Co (II) adsorption showed that the adsorbent successfully adsorbed Co (II) from aqueous solution. The effect of different parameters such as, contact time, initial concentration of cobalt ion, the adsorbent dose, and pH value was also investigated. The maximum efficiency of cobalt ion adsorption was measured 93.87% at a pH value of 6, contact time of 80 min, the adsorbent dose of 3 g/L, and initial ion concentration of 10 mg/L. Also, Langmuir, Freundlich, and D-R isotherm models were used to determine the most appropriate isotherm model for cobalt ion adsorption. The adsorption equilibrium data were better fitted with the Langmuir model with a maximum adsorption capacity of 93.46 mg/g. Additionally, the average free energy of adsorption was evaluated in the amount of 1.4085 KJ/mol, revealing a physical adsorption. Moreover, the kinetic behavior study showed that the experimental data follow the pseudo second order kinetic model to the value of correlation coefficient.

Performance of ceria/iron oxide nano-composites based on chitosan as an effective adsorbent for removal of Cr(VI) and Co(II) ions from aqueous systems

A novel chitosan/ceria/iron oxide (CS/ceria/Fe₃O₄) nano-composite adsorbent was synthesized for removal of Cr(VI) and Co(II) ions from aqueous systems in a batch system. The adsorbents were characterized by field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM), thermal gravimetric analysis (TGA), and Brunauer- Emmett-Teller (BET) analyses. The behavior of swelling kinetics was also studied. The effect of several adsorption parameters including CeO₂ and Fe₃O₄ contents, initial pH, contact time, initial Cr(VI) and Co(II) concentration, and temperature on the adsorption capacity was studied. The double exponential model revealed a better fit with the kinetic data of Cr(VI) and Co(II) ions. The Cr(VI) and Co(II) adsorption process well fitted the Langmuir model. The maximum adsorption capacities estimated from Langmuir isotherm model were 315.4 and 260.6 mg/g for Cr(VI) and Co(II) ions, respectively. Also, thermodynamic parameters were used to distinguish the nature of Cr(VI) and Co(II) adsorption. The reusability of CS/ceria/Fe₃O₄ nano-composite was evaluated with stripping agents of 0.1 M NaOH and 0.1 M HNO₃. Finally, the evaluation of Cr(VI)-Co(II) coexisting system confirmed that the presence of Co(II) ions played an inhibitor role on the Cr(VI) adsorption.

Extraction of Heavy Metals from Aqueous Medium by Husk Biomass: Adsorption Isotherm, Kinetic and Thermodynamic study

This study describes the adsorption of Cu (II), Co (II) and Ni (II) ions from wastewater on Vigna radiata husk biomass. The ability of adsorbent to capture the metal ions has been found to be in the order of Ni (II)>Co (II) and Cu (II) depending upon the size and nature of metal ions to be adsorbed. It has been observed that percentage removal of Cu (II), Co (II) and Ni (II) ions increases with increase of adsorbent dosage, contact time and pH of the medium but up to a certain extent. Maximum adsorption capacity (qmax) for Cu (II), Co (II) and Ni (II) ions has been found to be 11.05, 15.04 and 19.88 mg/g, respectively, under optimum conditions of adsorbent dosage, contact time and pH of the medium. Langmuir model best fits the adsorption process with R2 value approaches to unity for all metal ions as compared to other models because adsorption sites are seemed to be equivalent and only monolayer adsorption may occur as a result of binding of metal ion with a functional moiety of adsorbent. Pseudo second order kinetic model best interprets the adsorption process of Cu (II), Co (II) and Ni (II) ions. Thermodynamic parameters such as negative value of Gibbs energy (∆G°) gives information about feasibility and spontaneity of the process. Adsorption process was found to be endothermic for Cu (II) ions while exothermic for Co (II) and Ni (II) ions as signified by the value of enthalpy change (∆H°). Husk biomass was recycled three times for removal of Ni (II) from aqueous medium to investigate its recoverability and reusability. Moreover V. radiata husk biomass has a potential to extract Cu (II) and Ni (II) from electroplating wastewater to overcome the industrial waste water pollution.

Adsorption, Bioaccumulation and Kinetics Parameters of the Phytoremediation of Cobalt from Wastewater Using Elodea canadensis

Present paper investigates the phytoremediation of cobalt from wastewaters using Elodea canadensis. Bioaccumulation tests were conducted at various concentrations of cobalt ranging from 1 to 15 mg/L. Final concentrations of cobalt in wastewaters, after phytoremediation, were less than 1 mg/L. E. canadensis' hyperaccumulator character with regard to cobalt is emphasised by the amount of cobalt retained: 0.39% ± 0.02% of dry mass at an initial concentration in wastewater of 15 mg/L. After 14 days of exposure to contaminant, the biomass as well as the relative growth rate has increased with the amount of cobalt in wastewaters, the plant manifesting an excellent tolerance to cobalt exposure. Adsorption of cobalt ions by E. canadensis can be well described by the Langmuir adsorption isotherm and the pseudo-second-order model equation.

Radioactive Cobalt(II) Removal from Aqueous Solutions Using a Reusable Nanocomposite: Kinetic, Isotherms, and Mechanistic Study

A lignocellulose/montmorillonite (LMT) nanocomposite was prepared as a reusable adsorbent for cobalt(II) ions, and characterized by nitrogen (N₂) adsorption/desorption isotherm, X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared Spectroscopy (FTIR). LMT exhibited efficient adsorption of cobalt ions (Co(II)), and the adsorbed Co(II) was readily desorbed by nitric acid (HNO₃). All parameters affecting the adsorption and/or desorption of Co(II), including initial Co(II) concentration, pH value, temperature, HNO₃ concentration, and time, were optimized. The kinetic data analysis showed that the adsorption followed the pseudo-second-order kinetic model and fit well into the Langmuir isotherm equation. Notably, the nanocomposite can be used four times without significantly losing adsorbent capability. The Energy-Dispersive X-ray (EDX) and FTIR spectra analysis also revealed that the adsorption mechanism may be mainly a chemical adsorption dominated process.

Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II)

Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137mgg^-1 does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample.

Adsorption of heavy metals from aqueous solutions by Mg-Al-Zn mingled oxides adsorbent

In our study, Mg-Al-Zn mingled oxides were prepared by the co-precipitation method. The structure, composition, morphology and thermal stability of the synthesized Mg-Al-Zn mingled oxides were analyzed by powder X-ray diffraction, Fourier transform infrared spectrometry, N₂ physisorption, scanning electron microscopy, differential scanning calorimetry and thermogravimetry. Batch experiments were performed to study the adsorption behavior of cobalt(II) and nickel(II) as a function of pH, contact time, initial metal ion concentration, and adsorbent dose. The maximum adsorption capacity of Mg-Al-Zn mingled oxides for cobalt and nickel metal ions was 116.7 mg g^-1, and 70.4 mg g^-1, respectively. The experimental data were analyzed using pseudo-first- and pseudo-second-order kinetic models in linear and nonlinear regression analysis. The kinetic studies showed that the adsorption process could be described by the pseudo-second-order kinetic model. Experimental equilibrium data were well represented by Langmuir and Freundlich isotherm models. Also, the maximum monolayer capacity, q_max, obtained was 113.8 mg g^-1, and 79.4 mg g^-1 for Co(II), and Ni(II), respectively. Our results showed that Mg-Al-Zn mingled oxides can be used as an efficient adsorbent material for removal of heavy metals from industrial wastewater samples.

The impact of functionalized CNT in the network of sodium alginate-based nanocomposite beads on the removal of Co(II) ions from aqueous solutions

Significant efforts have been made to develop highly efficient adsorbents to remove radioactive Co(II) ion pollutants from medical and industrial wastewaters. In this study, amide group functionalized multi-walled carbon nanotube (CNT-CONH2) imprinted in the network of sodium alginate containing hydroxyapatite, and new nanocomposite beads were synthesized. Then, they were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS). The prepared nanocomposite beads were used as an adsorbent of Co(II) ions from an aqueous solution. The presence and distribution of Co(II) ions in the surface of the nanocomposite beads was confirmed using FESEM, EDS and metal mapping analysis. The effect of various experimental conditions such as time, pH, and initial concentration of the adsorbate solution and temperature on the adsorption capacity of the nanocomposite beads were explored. The maximum Co(II) ions adsorption capacity of the prepared nanocomposite beads with the largest surface area of 163.4m(2)g(-1) was 347.8mgg(-1) in the optimized condition. The adsorption mechanism followed a pseudo-second-order kinetic model. Furthermore, the Freundlich appears to produce better fit than the Langmuir adsorption isotherm. Finally, thermodynamic studies suggest that endothermic adsorption process of Co(II) ions is spontaneous and thermodynamically favorable.

A Rapid In Situ Colorimetric Assay for Cobalt Detection by the Naked Eye

A simple, rapid, and convenient colorimetric chemosensor of a specific target toward the end user is still required for on-site detection and real-time monitoring applications. In this study, we developed a rapid in situ colorimetric assay for cobalt detection using the naked eye. Interestingly, a yellow to light orange visual color transition was observed within 3 s when a Chrysoidine G (CG) chemosensor was exposed to cobalt. Surprisingly, the CG chemosensor had great selectivity toward cobalt without any interference of other metal ions. Under optimized conditions, a lower detection limit of 0.1 ppm via a spectrophotometer and a visual detection limit of 2 ppm with a linear range from 0.4 to 1 ppm (R² = 0.97) were determined. Moreover, the CG chemosensor is reversible and maintains its functionality after treatment with chelating agents. In conclusion, we show the superior capabilities of the CG chemosensor, which has the potential to provide extremely facile handling, high sensitivity, and a fast response time for applications of on-site detection to real-time cobalt monitoring for the general public.