Insight into the H2S selective catalytic oxidation performance on well-mixed Ce-containing rare earth catalysts derived from MgAlCe layered double hydroxides

Development of microwave-assisted nitrogen-modified activated carbon for efficient biogas desulfurization: a practical approach

Removal of H₂S (hydrogen sulfide) from biogas is anticipated for higher energy conversion of methane (CH₄), while reducing the detrimental impacts of corroding the metal parts in the plant and its hazardous effect on humans and the environment. The introduction of microwave (MW) heating and nitrogen-modification could generate superior adsorbent features, contributing to high H₂S removal. Up to date, there is no work reported on the influence of physicochemical characteristics of nitrogen-modified carbon synthesized via MW and conventional heating (TH) methods and their performance in H₂S removal. Palm shell activated carbon (PSAC) was functionalized with nitrogen groups via urea impregnation, followed by the synthesis of MW and TH at 950 °C, 500 ml/min of N₂ flow rate and 30 min of heating time. MW and TH heating effects on the modified PSAC adsorbent were analysed and compared towards hydrogen sulfide (H₂S) removal. PSAC with nitrogen functionalization produced using MW heating (PSAC-MW) demonstrates superior performance, with an adsorption capacity of 356.94 mg/g. The adsorbent sample generated using MW heating exhibited notable properties, including a large surface area and a sponge-like structure, with new pores developed within the current pores. Instead of that, there was an observation of 'hot spot' appearance during the MW heating process, which is believed to be responsible for the development of physical and chemical characteristics of the adsorbent. Thus, it is believed that MW heating was assisted in the development of the adsorbent's properties and at the same time contributed to the high removal of H₂S at low adsorption temperature. The utilization of biomass-based adsorbent (PSAC) for H₂S removal can address the lignocellulosic waste disposal problem, while mitigating the H₂S release from the biogas production plants thus has several environmental merits. This indirectly contributed to zero-waste generation, while overcoming the adverse effects of H₂S.

Ternary metal oxide nanocomposite for room temperature H2S and SO2 gas removal in wet conditions

A ternary Mn–Zn–Fe oxide nanocomposite was fabricated by a one-step coprecipitation method for the remotion of H₂S and SO₂ gases at room temperature. The nanocomposite has ZnO, MnO₂, and ferrites with a surface area of 21.03 m² g⁻¹. The adsorbent was effective in mineralizing acidic sulfurous gases better in wet conditions. The material exhibited a maximum H₂S and SO₂ removal capacity of 1.31 and 0.49 mmol g⁻¹, respectively, in the optimized experimental conditions. The spectroscopic analyses confirmed the formation of sulfide, sulfur, and sulfite as the mineralized products of H₂S. Additionally, the nanocomposite could convert SO₂ to sulfate as the sole oxidation by-product. The oxidation of these toxic gases was driven by the dissolution and dissociation of gas molecules in surface adsorbed water, followed by the redox behaviour of transition metal ions in the presence of molecular oxygen and water. Thus, the study presented a potential nanocomposite adsorbent for deep desulfurization applications.

Efficient degradation of organic pollutants by activated peroxymonosulfate over TiO2@C decorated Mg-Fe layered double oxides: Degradation pathways and mechanism

To activate peroxymonosulfate (PMS) is an efficient way for decomposition of non-biodegradable organic pollutants. Herein, Mg-Fe layered double oxides decorated with Ti₃C₂ MXene-derived TiO₂@C (T/LDOs) were fabricated to efficiently activate PMS for the degradation of Rhodamine B (RhB), acid red 1 (AR1), methylene blue (MB), and tetracycline hydrochloride (TC). The T/LDOs catalyst could decompose 95.8% of RhB, 94.8% of AR1, 84.9% of MB within 10 min, and 82.4% of TC within 60 min. The degradation rate constant of RhB in the optimal T/LDOs/PMS system was approximately 2.5 and 15.7 times higher than that in the Mg-Fe LDOs/PMS system and Mg-Fe LDH/PMS system, respectively. Importantly, the T/LDOs exhibited a wide working pH range (3.1-11.0) and high stability with low metal ions leaching, indicating its potential practical applications. Quenching experiments and electronic spin resonance results confirmed that both ^•O₂^- and ¹O₂ were the dominant active species in the T/LDOs/PMS system. In addition, the possible degradation pathway of RhB in the 5%-T/LDOs/PMS system was proposed. Finally, the catalytic mechanism study revealed that the T/LDOs with abundant surface hydroxyl groups and a certain amount of TiO₂@C facilitated the electron transfer between ≡Fe^(Ⅲ)‒OH complex and HSO₅^-, boosting the generation of ^•O₂^- and ¹O₂. This study provides an insight into exploiting highly efficient catalysts for PMS activation towards the degradation of organic pollutants.

Efficiently Integrated Desulfurization from Natural Gas over Zn-ZIF-Derived Hierarchical Lamellar Carbon Frameworks

Selective removal of carbonyl sulfide (COS) and hydrogen sulfide (H₂S) is the key step for natural gas desulfurization due to the highly toxic and corrosive features of these gaseous sulfides, and efficient and stable desulfurizers are urgently needed in the industry. Herein, we report a class of nitrogen-functionalized, hierarchically lamellar carbon frameworks (N-HLCF-xs), which are obtained from the structural transformation of Zn zeolitic imidazolate frameworks via controllable carbonization. The N-HLCF-xs possess the desirable characteristics of large Brunauer-Emmett-Teller surface areas (645-923 m²/g), combined primary three-dimensional microporosity and secondary two-dimensional lamellar microstructure, and high density of nitrogen base sites with enhanced pyridine ratio (17.52 wt %, 59.91%). The anchored nitrogen base sites in N-HLCF-xs show improved accessibility, which boosts their interaction with acidic COS and H₂S. As expected, N-HLCF-xs can be employed as multifunctional and efficient desulfurizers for selective removal of COS and H₂S from natural gas. COS was first transformed into H₂S via catalytic hydrolysis, and the produced H₂S was then captured and separated and catalyzed oxidation into elemental sulfur. The above continuous processes can be achieved with solo N-HLCF-xs, giving extremely high efficiencies and reusability. Their integrated desulfurization performance was better than many desulfurizers used in the area, such as activated carbon, β zeolite, MIL-101(Fe), K₂CO₃/γ-Al₂O₃, and FeO_x/TiO₂.

Layered Double Hydroxides Containing Rare Earth Cations: Synthesis and Applications

In this mini-review, we describe the currently available literature concerning synthesis and applications of layered double hydroxides (LDHs) containing rare earth cations (RE-LDHs), focusing on the catalytic activity of those compounds. The lack of studies of some rare earth elements (REE) and the insufficient knowledge of their catalytic activity in the structure of LDHs indicate the need for further research.

One-Step MOF-Templated Strategy to Fabrication of Ce-Doped ZnIn2 S4 Tetrakaidecahedron Hollow Nanocages as an Efficient Photocatalyst for Hydrogen Evolution

Achieving structure optimizing and component regulation simultaneously in the ZnIn2 S4 -based photocatalytic system is an enormous challenge in improving its hydrogen evolution performance. 3D hollow-structured photocatalysts have been intensively studied due to their obvious advantages in solar energy conversion reactions. The synthesis of 3D hollow-structured ZnIn2 S4 , however, is limited by the lack of suitable template or synthesis methods, thereby restricting the wide application of ZnIn2 S4 in the field of photocatalysis. Herein, Ce-doped ZnIn2 S4 photocatalysts with hollow nanocages are obtained via one-step hydrothermal method with an ordered large-pore tetrakaidecahedron cerium-based metal-organic frameworks (Ce-MOFs) as template and Ce ion source. The doping of Ce and the formation of ZnIn2 S4 tetrakaidecahedron hollow nanocages with ultrathin nanosheet subunits are simultaneously induced by the Ce-MOFs, making this groundbreaking work. The Ce-doped ZnIn2 S4 with a nonspherical 3D hollow nanostructure inherit the tetrakaidecahedron shape of the Ce-MOF templates, and the shell is composed of ultrathin nanosheet subunits. Both theoretical and experimental results indicate that the doping of Ce and the formation of hollow nanocages increase light capture and the separation of photogenerated charge carriers.

Insights into the mechanism of low-temperature H2S oxidation over Zn-Cu/Al2O3 catalyst

Odor pollution caused by toxic chemicals with low human olfactory thresholds, such as hydrogen sulfide (H₂S), has become a major cause of environmental grievance world-wide. Although the low-temperature (<180 °C) catalytic oxidation of H₂S using metal oxides has received widespread attention, desulfurization performance is not ideal. Herein, a series of Zn-Cu/Al₂O₃ catalysts were developed using an impregnation method based on the Al₂O₃ hydrophilicity and the effects of zinc loading on the catalyst physicochemical properties and performance were systematically studied. The catalysts were characterized using inductively coupled plasma-optical emission spectrometry (ICP-OES), N₂ adsorption-desorption isotherms, scanning electron microscopy with energy dispersive spectrometry (SEM-EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR) and electron paramagnetic resonance (EPR). It was found that optimization of zinc doping could improve the hydrophilicity of the catalyst, and hence its activity. Catalytic activity was also dependent on operational parameters such as temperature, humidity and space velocity. The Zn₃Cu₃ catalyst exhibited the highest breakthrough capacity of 353.91 mg/g at 50 °C and at a relative humidity of 50%. The excellent desulfurization performance was attributed to oxygen vacancies contributed by CuO, Cu₂O and ZnO, which facilitated the conversion of H₂O into hydroxyl radicals. Consequently, a hydroxyl radical-induced desulfurization mechanism over Zn-Cu/Al₂O₃ is proposed. This work provides a potential green and efficient catalyst for the selective oxidation of H₂S.

Oxygen Vacancy-Mediated Selective H2S Oxidation over Co-Doped LaFexCo1−xO3 Perovskite

Compared to the Claus process, selective H2S catalytic oxidation to sulfur is a promising reaction, as it is not subject to thermodynamic limitations and could theoretically achieve ~100% H2S conversion to sulfur. In this study, we investigated the effects of Co and Fe co-doping in ABO3 perovskite on H2S selective catalytic oxidation. A series of LaFexCo1−xO3 (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) perovskites were synthesized by the sol-gel method. Compared to LaFeO3 and LaCoO3, co-doped LaFexCo1−xO3 significantly improved the H2S conversion and sulfur selectivity at a lower reaction temperature. Nearly 100% sulfur yield was achieved on LaFe0.4Co0.6O3 under 220 °C with exceptional catalyst stability (above 95% sulfur yield after 77 h). The catalysts were characterized by XRD, BET, FTIR, XPS, and H2-TPR. The characterization results showed that the structure of LaFexCo1−xO3 changed from the rhombic phase of LaCoO3 to the cubic phase of LaFeO3 with Fe substitution. Doping with appropriate iron (x = 0.4) facilitates the reduction of Co ions in the catalyst, thereby promoting the H2S selective oxidation. This study demonstrates a promising approach for low-temperature H2S combustion with ~100% sulfur yield.

Engineering of crystal phase over porous MnO2 with 3D morphology for highly efficient elimination of H2S

In the present work, we report a facile oxalate-derived hydrothermal method to fabricate α-, β- and δ-MnO₂ catalysts with hierarchically porous structure and study the phase-dependent behavior for selective oxidation of H₂S over MnO₂ catalysts. It was disclosed that the oxygen vacancy, reducibility and acid property of MnO₂ are essentially determined by the crystalline phase. Systematic experiments demonstrate that δ-MnO₂ is superior in active oxygen species, activation energy and H₂S adsorption capacity among the prepared catalysts. As a consequence, δ-MnO₂ nanosphere with a hierarchically porous structure shows high activity and stability with almost 100% H₂S conversion and sulfur selectivity at 210 °C, better than majority of reported Mn-based materials. Meanwhile, hierarchically porous structure of δ-MnO₂ nanosphere alleviates the generation of by-product SO₂ and sulfate, promoting the adoptability of Mn-based catalysts in industrial applications.

Performance and mechanism of hydrogen sulfide removal by sludge-based activated carbons prepared by recommended modification methods

The sludge-based activated carbons (SACs) were prepared by sewage sludge and corn straw and modified by ferric nitrate. The H₂S removal performance and the desulfurization mechanism of the modified SAC were studied. Results showed that breakthrough sulfur capacity and saturation sulfur capacity of the SAC prepared by recommended modification were 27.209 mg/g and 48.098 mg/g, which were as 4.68 times and 7.02 times larger as those before modification, respectively. Additionally, results showed that the desulfurization products of unmodified SAC were mainly sulfur, while that of modified SAC were mainly sulfate. These results indicated that ferric nitrate modification changed the way of hydrogen sulfide removal by SAC: the desulfurization process of unmodified SAC can be expressed as S^2- → S⁰ → S⁴⁺ → S⁶⁺, and the oxidative active component was dominated by O*, while that of modified SAC can be expressed as S^2- → S⁰ → S⁶⁺, and the oxidative active components are both Fe³⁺ and O*.

N-doped honeycomb-like porous carbon derived from biomass as an efficient carbocatalyst for H2S selective oxidation

3D interconnected porous N-doped carbocatalyst derived from the waste air-laid paper plays as an efficient metal-free catalyst for H₂S removal in super-Claus reaction. The honeycomb-like porous nitrogen-doped carbons are fabricated through a facile impregnation of alkaline solution and NH₃ post-treatment method. The experiments prove that NH₃ post-treatment is an efficient way to improve the catalytic performance, which resulting in outstanding reactivity and stability with highest sulfur formation rate of 496.6 g_sulfurkg_cat.^-1 h^-1 and sulfur yield of 86.7 % in feed gas with high concentration (ca. 10,000 ppm) of H₂S for selective oxidation. Significantly, the optimized pyridinic-N content and defect degree endow the N-doped porous carbon (NPC700) with highest catalytic activity according to the Raman and XPS results. The high surface area and abundant porous structure also contribute to the high catalytic performance by increasing the exposure degree of active site and offering additional active surface. Based on the XPS, SEM, TEM and EDS mapping results, the N-doped porous carbon are proved to be stable catalysts since the morphology and surface chemical environment remain similar after the oxidative desulfurization process.

A solid thermal and fast synthesis of MgAl-hydrotalcite nanosheets and their applications in the catalytic elimination of carbonyl sulfide and hydrogen sulfide

MgAl hydrotalcites with high exposed OH⁻ sites were designed, and showed superior performance for the catalytic elimination of COS and H₂S.

Iron-Based Metal-Organic Frameworks as Platform for H2S Selective Conversion: Structure-Dependent Desulfurization Activity

Three classical Fe-MOFs, viz., MIL-100(Fe), MIL-101(Fe), and MIL-53(Fe), were synthesized to serve as platforms for the investigation of structure-activity relationship and catalytic mechanism in the selective conversion of H₂S to sulfur. The physicochemical properties of the Fe-MOFs were characterized by various techniques. It was disclosed that the desulfurization performances of Fe-MOFs with well-defined microstructures are obviously different. Among these, MIL-100(Fe) exhibits the highest catalytic performance (ca. 100% H₂S conversion and 100% S selectivity at 100-180 °C) that is superior to that of commercial Fe₂O₃. Furthermore, the results of systematic characterization and DFT calculation reveal that the difference in catalytic performance is mainly because of discrepancy in the amount of Lewis acid sites. A plausible catalytic mechanism has been proposed for H₂S selective conversion over Fe-MOFs. This work provides critical insights that are helpful for rational design of desulfurization catalysts.

Luminescence Tuning of Layered Rare-Earth Hydroxides (LRHs, R = Tb, Y) Composites with 3-Hydroxy-2-naphthoic Acid and Application to the Fluorescent Detection of Al3

Tunable luminescence (quenching or blue shift) of HNA/OS-LRH composites (HNA is 3-hydroxy-2-naphthoic acid; OS is the anionic surfactant of 1-octanesulfonic acid sodium; LRHs are layered rare-earth hydroxides, R = Tb³⁺, Y³⁺) in the solid state and delaminated state is reported, which is utilized as an effective fluorescent probe for detecting metal ions. HNA/OS species are intercalated into LRH layers to generate composites of HNA _xOS_{1- x}-LTbH ( x = 0.10, 0.15, 0.20 , 0.25) and HNA _yOS_{1- y}-LYH ( y = 0.05, 0.10, 0.15, 0.20, 0.25, 0.30). In the solid state, LYH composites exhibit green emissions (from 493 to 504 nm) with a large blue shift in comparison to the 542 nm emission of free HNA^- anions, while in the delaminated state in formamide (FM), the composites display blue emission (480 nm) relative to the green emission (512 nm) of an HNA soltuion in FM. However, LTbH composites display coquenched luminescence in both the solid state and delaminated state. Also, HNA_0.25OS_0.75-1:1-LYH, HNA_0.25OS_0.75-1:2-LYH, and HNA_0.05OS_0.95-1:1-LYH (1:1 and 1:2 are HNA:NaOH molar ratios) show significantly elongated fluorescence lifetimes of 15.35, 14.37, and 12.72 ns, respectively, in comparison with free HNA-Na (6.44 ns), and their quantum yields of 23.40%, 21.97%, and 22.31%, respectively, are much larger than that of free HNA-Na (4.86%). The LTbH composite (HNA_0.25OS_0.75-1:1-LTbH) has also a relatively higher quantum yield of 12.46%. The HNA_0.25OS_0.75-1:1-LYH colloid exhibits excellent recognition selectivity for Al³⁺ over other metal ions (Mg²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, and Hg²⁺) with distinct fluorescence sensitization. It shows an intense change in its fluorescence emission when it is bound to Al³⁺ ions, giving a lower detection limit of 6.32 × 10^-6 M. This is novel research on the fluorescence chemosensing of LRH composites.

High-sulfur capacity and regenerable Zn-based sorbents derived from layered double hydroxide for hot coal gas desulfurization

The Zn-Al mixed metal oxide (ZnAl-MMO) with a plate-like structure was derived from Zn-Al layered double hydroxide. The ZnAl-MMO with a Zn/Al molar ratio of 3:1 exhibits superior absorption ability for H₂S in a simulated coal gas at 600 ℃ due to the special structure of the ZnAl-MMO. Besides ZnS, elemental sulfur is also produced during the desulfurization process. The deactivation model could well simulate the absorption behavior of H₂S. The sulfidation reaction over the sorbent shows large initial reaction rate constants (1110-5390 m³ min^-1  kg^-1) and low activation energy (29.5 kJ mol^-1). The regeneration rate of the used sorbent can reach 99.8% under the optimum conditions. The regenerated sorbents still show high sulfur capacity (ca. 30%), implying its great application potential for industrial-scale desulfurization of the hot coal gas.

MOF-derived porous Fe2O3 with controllable shapes and improved catalytic activities in H2S selective oxidation

Porous Fe₂O₃ architectures with controllable shapes are synthesized by the MOF-template method and show excellent catalytic activity for H₂S selective oxidation.