Fluoride ion accelerating degradation of organic pollutants by Cu(II)-catalyzed Fenton-like reaction at wide pH range

Fluoride ions enhanced cobalt ferrite for peroxymonosulfate activation with efficient performance and active oxygen yield regulation

The activation of peroxymonosulfate (PMS) by cobalt-based catalysts for the degradation of organic pollutants has been widely studied, while the role of coexisting anions has received little attention. In this study, the performance of atrazine (ATZ) degradation by the addition of fluoride ions (F-) in the activation of PMS by cobalt ferrite (CoFe2O4) was investigated. The addition of F- to the CoFe2O4/PMS system increased ATZ degradation effect from 82 % to 98 % within 10 min, and the rate increased from 0.172 min-1 to 0.431 min-1. At the same time, F- could also enhance the degradation of organic substances such as sulfamethoxazole (SMX), ibuprofen, and iohexol. Based on generating SO4•-, HO• and Co(IV)=O in the CoFe2O4/PMS system, F- enhanced the generation of SO4•-. When coexisting with common substances in water (i.e., inorganic anions, humic acid, hemoglobin and dextran), F- can still increase the reaction rate and reduce their negative impacts. Ion dissolution and control tests verified Co as a valid active site. A potential reaction mechanism was proposed for the complex Co(II)F formation with Co by F-, which enhanced the activation of the PMS by CoFe2O4 and regulated the active species. Finally, it was verified that the low concentration of F- could enhance ATZ degradation within two hours and the remaining F- could be effectively removed by flocculation and precipitation. This research takes utilization of F- in wastewater to promote advanced oxidation processes based on PMS, which provides a new direction for the treatment of actual water pollution.

Smart Enzyme-Like Polyphenol-Copper Spray for Enhanced Bacteria-Infected Diabetic Wound Healing

Developing functional medical materials is urgent to treat diabetic wounds with a high risk of bacterial infections, high glucose levels and oxidative stress. Here, a smart copper-based nanocomposite acidic spray has been specifically designed to address this challenge. This copper-based nanocomposite is pH-responsive and has multienzyme-like properties. It enables the spray to effectively eliminate bacteria and alleviate tissue oxidative pressure, thereby accelerating the healing of infected diabetic wounds. The spray works by generating hydroxyl radicals through catalysing H2O2, which has a high sterilization efficiency of 97.1%. As alkaline micro-vessel leakage neutralizes the acidic spray, this copper-based nanocomposite modifies its enzyme-like activity to eliminate radicals. This reduces the level of reactive oxygen species in diabetic wounds by 45.3%, leading to a similar wound-healing effect between M1 diabetic mice and non-diabetic ones by day 8. This smart nanocomposite spray provides a responsive and regulated microenvironment for treating infected diabetic wounds. It also offers a convenient and novel approach to address the challenges associated with diabetic wound healing.

Copper-cysteamine nanoparticle-mediated microwave dynamic therapy improves cancer treatment with induction of ferroptosis

Photodynamic Therapy (PDT) holds a great promise for cancer patients, however, due to the hypoxic characteristics of most solid tumors and the limited penetration depth of light in tissues, the extensive clinical application of PDT is limited. Herein, we report microwave induced copper-cysteamine (Cu-Cy) nanoparticles-based PDT as a promising cancer treatment to overcome cancer resistance in combination with ferroptosis. The treatment efficiency of Cu-Cy-mediated microwave dynamic therapy (MWDT) tested on HCT15 colorectal cancer (CRC) cells via cell titer-blue cell viability assay and live/dead assay reveal that Cu-Cy upon MW irradiation can effectively destroy HCT15 CRC cells with average IC-50 values of 20 μg/mL. The cytotoxicity of Cu-Cy to tumor cells after MW stimulation can be alleviated by ferroptosis inhibitor. Furthermore, Cu-Cy mediated MWDT could deplete glutathione peroxide 4 (GPX4) and enhance lipid peroxides (LPO) and malondialdehyde (MDA). Our findings demonstrate that MW-activated Cu-Cy killed CRC cells by inducing ferroptosis. The superior in vivo antitumor efficacy of the Cu-Cy was corroborated by a HCT15 tumor-bearing mice model. Immunohistochemical experiments showed that the GPX4 expression level in Cu-Cy + MW group was significantly lower than that in other groups. Overall, these findings demonstrate that Cu-Cy nanoparticles have a safe and promising clinical application prospect in MWDT for deep-seated tumors and effectively inhibit tumor cell proliferation by inducing ferroptosis, which provides a potential solution for cancer resistance.

Applications of metal-phenolic networks in nanomedicine: a review

The exploration of nanomaterials is beneficial for the development of nanomedicine and human medical treatment. Metal-phenolic networks (MPNs) have been introduced as a nanoplatform for versatile functional hybrid nanomaterials and have attracted extensive attention due to their simple preparation, excellent properties and promising medical application prospects. This review presents an overview of recent synthesis methods for MPNs, their unique biomedical properties and the research progress in their application in disease detection and treatment. First, the synthesis methods of MPNs are summarised, and then the advantages and applicability of each assembly method are emphasised. The various functions exhibited by MPNs in biomedical applications are then introduced. Finally, the latest research progress in MPN-based nanoplatforms in the biomedical field is discussed, and their future research and application are investigated.

Photocatalytic concrete for degrading organic dyes in water

Since the advent of photocatalytic degradation technology, it has brought new vitality to the environmental governance and the response to the energy crisis. Photocatalysts harvest optical energy to drive chemical reactions, which means people can use solar energy to complete some resource-consuming activities by photocatalysts, such as environmental governance. In recent years, researchers have tried to combine photocatalyst TiO₂ with building materials to purify urban air and obtained good results. One of the important functions of photocatalysts is to degrade organic pollutants in water through light energy, but this technology has not been reported in the practical application areas. To extend this technology to practical application areas, photocatalytic concrete for degrading pollutants in waters was proposed and demonstrated for the first time in this paper. The photocatalytic concrete proposed based on the K-g-C₃N₄ shows a strong ability to degrade the organic dyes. According to the experiment results, the angle of light source plays an important role in the process of photocatalytic degradation, while waters with pH value of 6.5-8.5 hardly influenced the degradation of organic dyes. When the angle of light source is advantageous for photocatalytic concrete to absorb more visible light, more organic dyes will be degraded by photocatalytic concrete. The degradation rate of methylene blue could reach about 80% in ½ hour under desirable conditions and is satisfied compared with that of reported works. This study implicates that photocatalytic concrete can effectively degrade organic dyes in water. The influences of changes in the water environment hardly affect the degradation of organic pollutants, which means photocatalytic concrete can be widely used in green infrastructures to achieve urban sewage treatment.

Highly Efficient Oxygen-Activated Self-Cleaning Membranes Prepared by Grafting a Metal-Organic Framework-Derived Catalyst

In this study, an efficient oxygen-activated self-cleaning membrane was successfully prepared by grafting a metal-organic framework-devised catalyst (CuNi-C) onto a membrane surface, resulting in enhanced filtration performance and self-cleaning capability based on oxygen activation under mild conditions. The pore features, surface roughness, and surface hydrophilicity of the prepared membrane were analyzed and used to determine the causes of the enhanced filtration performance; the results showed that an increase in the porosity and surface roughness enhanced the permeate flux, and enhanced adsorption capacity and surface hydrophobicity improved the membrane removal efficiency. The self-cleaning mechanism was elucidated by identifying the reactive oxygen species (ROS) and detecting catalytic element valences. The results revealed that zero-valent Cu embedded into the membrane surface effectively activated natural dissolved oxygen (DO) to generate ROS that degraded organic pollutants. In this study, catalytic oxidation with DO as the oxidant was successively integrated with membrane separation to prevent membrane fouling, providing a novel direction for the development of multifunctional membranes.

Design and synthesis of three new copper coordination polymers: efficient degradation of an organic dye at alkaline pH

Three new coordination polymers (CPs) based on Cu(II), namely {[Cu₆(H₂L)₄(4,4'-bpy)₆(H₂O)₂]·16H₂O}_n(1), {[Cu(H₃L)(1,4-bib)]·3H₂O}_n(2), and {[Cu₂(H₂L)₂(1,4-bib)₂][Cu(1,4-bib)(H₂O)₂]}_n·4nH₂O(3) (H₅L = 6-(3',4'-dicarboxyphenoxy)-2,3,5-benzene tricarboxylic acid, 4,4'-bpy = 4,4'-bipyridine and 1,4-bib = 1,4-bis(1H-imidazol-1-yl)benzene) were synthesized under hydrothermal conditions and characterized. 1 adopts a three-dimensional structure and can be described with the point symbol {4·5²}₂{4²·5⁴·6⁴·8³·9²}{5·10⁴·12} whereas 2 shows a layered structure. 3 can be perceived as a complex salt of two coordination polymers: the cationic component [Cu(1,4-bib)(H₂O)₂]_n²⁺ (3a) represents a chain polymer and the second anionic moiety [Cu₂(H₂L)₂(1,4-bib)₂]_n^2- (3b) corresponds to a 2D sub-structure. In the presence of H₂O₂, all complexes 1-3 act as efficient photocatalysts for the degradation of the dye methylene blue (MB). The effects of properties such as initial MB concentration, catalyst dosage, pH value, and H₂O₂ concentration on MB degradation were also investigated and analyzed in detail. Compounds 1-3 exhibit excellent structural stability during the catalytic process and can be reused at least three times. The hydroxyl radical (OH˙) and holes (h⁺) were confirmed as the main active species in the degradation process.

Degradation of sulfamerazine by a novel CuxO@C composite derived from Cu-MOFs under air aeration

Most metal-organic frameworks (MOFs) are synthesized from carboxylate and metal precursors by hydrothermal process, which will consume a large amount of solvent and carboxylate. To address this issue, a new strategy for Cu-based MOFs was developed, in which the Cu-based MOFs was obtained by using abundant natural polymer (tannic acid) as one of the precursors and using high-energy ball milling to achieve a self-assembly of tannic acid and copper sulfate. Based on this strategy, a novel Cu-based MOFs derivative (Cu_xO@C composite) was synthesized by high-temperature sintering of Cu-based MOFs and used for sulfamerazine (SMR) removal via O₂ activation. The BET specific surface area and average pore size of Cu_xO@C composite were 110.34 m² g^-1 and 21.06 nm, respectively, which made Cu_xO@C composite had the maximum adsorption capacity (Q_max) for SMR of 104.65 mg g^-1 and favored the subsequent degradation of SMR. The results from XRD and XPS indicated that Cu_xO@C composite contained a lot of Cu⁰ and Cu₂O with the sizes of 76.6 nm and 9.8 nm, respectively, which led to its high performance of O₂ activation. The removal efficiency of SMR and 90.2% TOC achieved 100% and 90.2%, respectively in the Cu_xO@C/air system at initial pH of 4.0, air flow rate of 100 mL min^-1, Cu_xO@C dosage of 1 g L^-1 and reaction time of 30 min. Reactive species, including H₂O₂, OH and O₂^- radicals were detected in the Cu_xO@C/air system, and OH and O₂^- were mainly responsible for the degradation of SMR.

Minute Cu2+ coupling with HCO3- for efficient degradation of acetaminophen via H2O2 activation

Homogeneous Cu²⁺-mediated activation of H₂O₂ has been widely applied for the removal of organic contaminants, but fairly high dosage of Cu²⁺ is generally required and may cause secondary pollution. In the present study, minute Cu²⁺ (2.5 μM) catalyzed H₂O₂ exhibited excellent efficiency in degradation of organic pollutants with the assistant of naturally occurring level HCO₃^- (1 mM). In a typical case, acetaminophen (ACE) was completely eliminated within 10 min which followed the pseudo-first-order kinetics. Singlet oxygen and superoxide radical rather than traditionally identified hydroxyl radical were the predominant reactive oxygen species (ROS) responsible for ACE degradation. Meanwhile, Cu³⁺ was deduced through Cu⁺ and p-hydroxybenzoic acid formation analysis. CuCO₃(aq) was the main complex with high reactivity for the activation of H₂O₂ to form ROS and Cu³⁺. The removal efficiency of ACE depended on the operating parameters, such as Cu²⁺, HCO₃^- and H₂O₂ dosage, solution initial pH. The presence of Cl^-, HPO₄^2-, humic acid were found to retard ACE removal while other anions such as SO₄^2- and NO₃^- had no obvious effect. ACE exhibited lower degradation efficiency in real water matrices than that in ultra-pure water. Nevertheless, 58-100% of ACE was removed from domestic wastewater, lake water and tap water within 60 min. Moreover, eight intermediate products were identified and the possible degradation pathways of ACE were proposed. Additionally, other typical organic pollutants including bisphenol A, norfloxacin, lomefloxacin hydrochloride and sulfadiazine, exhibited great removal efficiency in the Cu²⁺/H₂O₂/HCO₃^- system.

Synergistically homogeneous-heterogeneous Fenton catalysis of trace copper ion and g-C3N4 for degradation of organic pollutants

Using the bulk g-C₃N₄ as a precursor, four g-C₃N₄ nanosheets were further prepared by ultrasonic, thermal, acid, and alkali exfoliation. The structures of these materials were characterized by various techniques such as X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. The synergistical Fenton catalysis of these materials with Cu²⁺ was evaluated by using rhodamine B as a simulated organic pollutant. The results showed that there existed a significant synergistical Fenton catalysis between Cu²⁺ and g-C₃N₄. This synergistic effect can be observed even when the concentration of Cu²⁺ was as low as 0.064 mg L^-1. The properties of g-C₃N₄ strongly influenced the catalytic activity of the Cu²⁺/g-C₃N₄ system. The coexistent of Cu²⁺ and the alkali exfoliated g-C₃N₄ showed the best catalytic activity. Hydroxyl radicals as oxidizing species were confirmed in the Cu²⁺/g-C₃N₄ system by electron paramagnetic resonance spectra. The synergistic catalysis may be attributed to the easier reduction of Cu²⁺ adsorbed on the g-C₃N₄. This study provided an excellent Fenton catalytic system, and partly solved the rapid deactivation of heterogeneous Fenton catalysts caused by the leaching of metal ions.

Efficient degradation of ciprofloxacin by magnetic γ-Fe2O3-MnO2 with oxygen vacancy in visible-light/peroxymonosulfate system

In this work, the magnetic γ-Fe₂O₃-MnO₂ bifunctional catalyst with oxygen vacancy was synthesized for peroxymonosulfate (PMS) activation under visible light. The activity of γ-Fe₂O₃-MnO₂ was investigated by ciprofloxacin (cipro) degradation. Results showed that 98.3% of cipro (50 μM) was removed within 30 min in visible-light/PMS system mediated by γ-Fe₂O₃-MnO₂ (2:1) with fine-tuned oxygen vacancy. The cipro degradation data fitted well with pseudo-first-order kinetic model with the highest kinetic constant of 0.114 min^-1. Besides, the γ-Fe₂O₃-MnO₂ exhibited stability, recyclability and practicability. High selectivity for cipro degradation was observed with coexisting anions in visible-light/γ-Fe₂O₃-MnO₂/PMS system. Furthermore, the enhanced mechanism of PMS activation under visible light with γ-Fe₂O₃-MnO₂ was proposed. The appropriate oxygen vacancy enhanced the separation of photo-induced carriers and Z scheme heterostructure maintained the highest redox potential. Accordingly, the synergistic effect of photocatalysis and PMS activation enhanced cipro degradation. Free radical and non-radical species including , h⁺, ¹O₂, •OH and co-existed in the coupled system. Impressively, this study provides a handy approach for oxygen vacancy regulation in metallic oxides composite and an easily recycled catalyst with high-activity in coupled oxidation system towards antibiotic degradation.

Bisphenol A degradation using waste antivirus copper film with enhanced sono-Fenton-like catalytic oxidation

This study investigated the applicability of waste antivirus copper film (CF) as a Fenton-like catalyst. The reaction activity of H₂O₂ and CF in combination was significantly enhanced by ultrasound (US) irradiation, and the synergy factor calculated from bisphenol A (BPA) degradation using CF-H₂O₂-US was 9.64 compare to that of dual factors. Photoluminescence analyses were conducted to compare the generation of hydroxyl radicals during both processes. In this sono-Fenton-like process, BPA degradation was affected by solution pH, temperature, ultrasound power, CF size, H₂O₂ dose, and initial BPA concentration. The BPA degradation curves showed an induction period (first stage) and a rapid degradation period (second stage). Process efficiency was totally and partially enhanced in the presence of chloride and carbonate ions, respectively. Chemical scavenger tests showed that both free and surface-bound hydroxyl radicals participate in BPA degradation under the sono-Fenton-like process using CF. The functional groups and copper crystals on the CF surface remained unchanged after five consecutive reuses, and the BPA degradation efficiency of CF was maintained over 80% during the reuse processes as a sono-Fenton-like catalyst.

Facile Fabrication of a Novel Copper Nanozyme for Efficient Dye Degradation

In this study, a novel copper nanozyme (CNZ) was synthesized by a mild way and characterized by scanning electron microscopy and Fourier transform infrared spectroscopy (FTIR). The as-fabricated CNZ exhibited typical peroxidase activity toward 2, 2'-azinodi-(3-ethylbenzthiazoline)-6-sulfonate. We successfully applied CNZ for the degradation of methyl orange pollutants. Under the optimum conditions (pH, 3.0; T, 60 °C; H2O2 concentration, 200 mM; dosage of CNZ, 8 mg), 93% of the degradation rate could be obtained in less than 10 min. Furthermore, the nanozyme exhibited excellent reusability and storage stability. All these experimental results suggested that CNZ is a powerful catalyst for industrial wastewater treatment.

Porous urchin-like 3D Co(ii)Co(iii) layered double hydroxides for high performance heterogeneous Fenton degradation

Heterogeneous Fenton processes can overcome the generation of iron sludge and the production of more solid wastes.

Conversion of tannery solid waste to an adsorbent for high-efficiency dye removal from tannery wastewater: A road to circular utilization

The high value-added use of tannery solid waste and elimination of tannery liquid waste in the leather-making industry have attracted widespread attention. In this study, a MgO-doped biochar (MgO/BC) adsorbent was successfully prepared by utilizing tannery solid waste (i.e., non-tanned hide wastes) as the biomass material for dye removal from tannery wastewater. Characterization results indicated that MgO was uniformly embedded into the porous BC structure. The adsorption capacity of acid orange II by MgO/BC reached up to 448.4 mg g^-1, which drastically exceeded the pure BC and other reported adsorbents. The adsorption behavior of acid orange II by MgO/BC matched nicely with Langmuir isotherm and pseudo-second-order kinetic model. This satisfactory adsorption capacity of MgO/BC for acid orange II was mainly due to the large specific surface area and the enhanced electrostatic interaction. According to the BET, zeta potential and XPS analysis, the possible mechanism towards acid orange II removal was attributed to the pore filling, surface complexation, electrostatic attraction and π-π interaction. In addition, MgO/BC showed the efficient removal towards anionic dyes from actual tannery wastewater. This work could provide guidance for the value-added utilization of tannery solid waste and a practical way to remove dyes from tannery wastewater.

Multifunctional chitosan-copper-gallic acid based antibacterial nanocomposite wound dressing

Antibacterial wound dressings can effectively avoid the residual of antibacterial nanomaterials for injection in vivo, reduce their biological toxicity to normal cells and tissues, making them be widely applied in biomedical field. Herein, an approach of combining ion-crosslinking, in-situ reduction and microwave-assisted methods was employed to prepare chitosan-copper-gallic acid nanocomposites (CS-Cu-GA NCs) with dual-functional nano-enzyme characteristics (oxidase- and peroxidase-like functions). The oxidase-like activity of CS-Cu-GA NCs can facilitate the production of hydrogen peroxide (H₂O₂) when it contacted with physiologically relevant antioxidants (AH₂) in bacteria. Subsequently, H₂O₂ was catalyzed to generate hydroxyl radicals (OH) under the peroxidase-like activity of CS-Cu-GA NCs. Furthermore, CS-Cu-GA NCs integrate the inherent antibacterial properties of chitosan, Cu NPs and Cu²⁺. Animal experiments revealed that the antibacterial dressing incorporating CS-Cu-GA NCs exhibited its effective promotion of S. aureus-infected wounds healing, as well as no damage to normal tissues. Besides, the antibacterial dressing was prepared to a band aid with excellent water swelling and antibacterial properties, which was further fixed in a medical tape to construct a portable antibacterial product that can be applied to the surface of human skin and showed excellent waterproof performance, providing a new insight for the construction of clinical antibacterial wound healing products.

Efficient fenton-like degradation of ofloxacin over bimetallic Fe-Cu@Sepiolite composite

An effective method for increasing the utilization efficiency of active components in heterogeneous Fenton-like catalysts was provided. 1.5 at.% Fe-Cu bimetal on 1D sepiolite (Sep) (D-FeCu@Sep) with high dispersion and reduced chemical valence was prepared via complexation-carbonization process of glutathione. 93% of ofloxacin (OFX, a typical antibiotic of emerging concern) was degraded over D-FeCu@Sep without any extra energy input at the optimum conditions (100 mL 10 mg/L OFX, pH 5.0, 3.0 g/L catalyst and 0.03 M H₂O₂), which was enhanced by 2.3, 3.0 and 1.7 times compared with aggregated Fe-Cu on Sep (A-FeCu@Sep), monometallic Fe on Sep (D-Fe@Sep) and Fe-Cu on blocky Celite (D-FeCu@Celite), respectively. Moreover, it exhibited an excellent performance at a wide working pH range from acidic to neutral conditions (pH 3.2-7.2) with a satisfied stability. Based on the characterizations of X-ray photoelectron spectroscopy (XPS), inductively coupled plasma mass spectrometry (ICP-MS), transmission electron microscopy (TEM), hydrogen temperature-programmed reduction (H₂-TPR) and electrochemical impedance spectroscopy (EIS), the proposed complexation-carbonization process of glutathione played an important role in the good Fenton performance of D-FeCu@Sep. The complexation of Fe and Cu ion by glutathione favors the high dispersion of Fe-Cu active component, afterward the reduced chemical valence results from carbonization process of glutathione. Moreover, the 1D nanofibrous structure of D-FeCu@Sep could greatly increase the surface electron transfer efficiency compared with D-FeCu@Celite. This study provides a method alternative to the heterogeneous Fenton chemistry by increasing the utilization efficiency of active components.

Rosmarinic acid enhanced Fe(III)-mediated Fenton oxidation removal of organic pollutants at near neutral pH

In this study, we reported that the presence of rosemary acid (RA) could strongly enhance the Fe(III)-mediated Fenton oxidation of 2,4-DCP as the model contaminant at near neutral pH. This enhancement was verified by the strong chelating and reducing ability of RA, which could prevent ion precipitation and accelerate the Fe³⁺/Fe²⁺ cycle. Radical quenching experiments and electron paramagnetic resonance confirmed the existence and roles of hydroxyl radicals in the Fe³⁺/RA/H₂O₂ system. Lot size optimized experiments were executed to achieve efficient 2,4-DCP degradation (99.93%) under the optimum conditions of 100 μmol/L Fe³⁺, 100 μmol l/L RA and 8 mmol/L H₂O₂ within 60 min. In addition, co-existing metal ions, inorganic anions and natural organic matters were proved that they could inhibit removal efficiency and rate at varying degrees. Total organic carbon and chloride ion measurements were employed to probe the mineralization of organic matters (including RA and 2,4-DCP). This study provides a new modified Fenton system to enhance the oxidation removal of refractory organics in water and will enrich the understanding on effective H₂O₂ activation at neutral pH.

Catalytic activation of O2 by Al0-CNTs-Cu2O composite for Fenton-like degradation of sulfamerazine antibiotic at wide pH range

In this study, a novel Al°-CNTs-Cu₂O composite, capable of activating O₂ to generate H₂O₂ and further to reactive oxygen species (ROSs) at a wide pH range, was synthetized, characterized and applied for the degradation of sulfamerazine. In the activation of O₂ by Al°-CNTs-Cu₂O composite, H₂O₂ was generated from the reaction of O₂ with Al°-CNTs, which could be catalytically decomposed into O₂^- and OH by Cu₂O, the formed Cu(II) could be rapidly reduced to Cu₂O by Al°-CNTs in composite, which made Al°-CNTs-Cu₂O composite reusable and decreased the leaching of copper ions into solution. The removal efficiency of SMR and TOC was 73.91 % and 56.80 %, respectively at initial pH = 5.8, T = 20 °C, O₂ flow rate = 100 mL/min, Al°-CNTs-Cu₂O dosage = 2 g/L, SMR = 50 mg/L, and reaction time = 60 min. The removal efficiency of SMR kept almost unchanged and the concentration of copper ions in solution was below 0.5 mg/L. The Al°-CNTs-Cu₂O/O₂ process could be used as a novel catalyst for the degradation of refractory organic contaminants in water and wastewater by Fenton-like process at a wide pH range through the in situ generation of H₂O₂.

Decomposition performance of hypochlorite on bead-type NiOx(OH)y catalyst: improving applicability of catalysts

An easy-to-use, pollution-free and reusable beaded NiO_x(OH)_y catalyst for improving hypochlorite oxidation was prepared by impregnating the mixture of persulfate and alkali over alumina and then reduced it with Ni²⁺. The effects of catalyst preparation conditions and reaction parameters on NaClO conversion rate and Ni²⁺ dissolution rate were studied. Impregnating the γ-Al₂O₃ beads in PS/OH^- mixed solution with 0.59 M PS and PS/OH^- molar ratio of 1.1, and then reducing with 0.8 M Ni²⁺ solution is the best condition for preparing catalyst. The catalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The best catalytic layer is characterized by high content of chemisorbed oxygen which can be converted into atomic oxygen. The hypochlorite conversion rate increased with the catalyst dosage and reuse times, and decreased with available chlorine, while pH of hypochlorite solution had little effect on the conversion rate. After running stably for 120 h in continuous flow test, the chemisorbed oxygen content in the optimal catalytic layer decreased slightly. Atomic oxygen plays an important role in the decolorization of dye solution by NaClO/NiO_x(OH)_y system. The oxidant consumption cost of this process is much cheaper than Fenton reagent. The prepared catalyst has great potential in hypochlorite decomposition and wastewater treatment.

Gold nanozyme as an excellent co-catalyst for enhancing the performance of a colorimetric and photothermal bioassay

Advanced oxidation processes (AOPs) have recently proposed for advancing colorimetric sensing applications, owing to their excellent performance of sensitive color readout that generated from the oxidation of chromogenic substrates like 3,3',5,5'-tetramethylbenzidine (TMB) by reactive oxygen species (ROS) of AOPs such as ·OH and ·O₂^- radicals. However, the efficiency of ROS generation and the related H₂O₂ decomposition in most AOPs is quite low especially at neutral pH, which greatly hampered the practical sensing applications of the AOPs. We herein communicated that β-cyclodextrin (β-CD)-capped gold nanoparticles (β-CD@AuNPs) can promote catalysis at neutral pH for AOP as an excellent co-catalyst. In this strategy, inorganic pyrophosphate (PPi) ions was first used to coordinate with Cu²⁺ and form Cu²⁺-PPi complex. In the presence of hydrogen peroxide, target inorganic pyrophosphatase (PPase) can hydrolyze PPi into inorganic phosphate (Pi) and release free Cu²⁺ simultaneously, resulting in a Cu²⁺-triggered Fenton-like AOP reaction. The introduced β-CD@AuNPs acts as a co-catalyst, analogous to mediators in the most co-catalyzed system, to enhance the rate-limiting step of Cu²⁺/Cu⁺ conversion in Cu²⁺/H₂O₂ Fenton-like AOP and resulting in an efficient generation of ·OH and ·O₂^- radicals, which further producing an intense blue color by oxidizing TMB into its oxidation product (TMBox) within a short time. Finally, this reaction system was used to simply detecting target PPase with the colorimetric and photothermal readout based on the in-situ generated TMBox indicator. More significantly, we successfully demonstrated nanozyme can serve as a co-catalyst to promote the AOP catalysis at neutral pH, and inspire other strategies to overcome the pH limitation in the AOP catalysis and expand its colorimetric and photothermometric application.

Graphitic carbon nitride (g-C3N4) as an efficient metal-free Fenton-like catalyst for degrading organic pollutants: the overlooked non-photocatalytic activity

Graphitic carbon nitride (g-C₃N₄) has attracted a large amount of research, mainly being used as a photocatalyst, but its Fenton-like catalytic performance has been overlooked. In this paper, the dark Fenton-like catalytic performance of g-C₃N₄ was evaluated by degrading rhodamine B over a wide pH range. The results showed that the g-C₃N₄, which was synthesized by conventional urea pyrolysis without any modification, was an efficient metal-free heterogeneous Fenton-like catalyst. The highest activity occurred under a weakly alkaline condition of about pH 10. The experiment of catalyst recycling indicated that g-C₃N₄ had long-term stability. The reactive oxidizing species of HO·, generated by the g-C₃N₄ activating H₂O₂, was identified by EPR and further supported by a scavenging experiment of HO· using isopropanol as the scavenger. The HNO₃ oxidation of g-C₃N₄ resulted in catalytic deactivation, implying the catalytic activity originated from the surface reduced groups of g-C₃N₄. The structure of synthesized g-C₃N₄ before and after the HNO₃ oxidation was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy, and a possible catalytic mechanism was proposed.

A High-Efficiency CuO/CeO2 Catalyst for Diclofenac Degradation in Fenton-Like System

An efficient Fenton-like catalyst CuO/CeO₂ was synthesized using ultrasonic impregnation and used to remove diclofenac from water. The catalyst was characterized by N₂ adsorption-desorption, SEM-EDS, XRD, HRTEM, Raman, and XPS analyses. Results showed that CuO/CeO₂ possessed large surface area, high porosity, and fine elements dispersion. Cu was loaded in CeO₂, which increased the oxygen vacancies. The exposed crystal face of CeO₂ (200) was beneficial to the catalytic activity. The diclofenac removal experiment showed that there was a synergistic effect between CuO and CeO₂, which might be caused by more oxygen vacancies generation and electronic interactions between Cu and Ce species. The experimental conditions were optimized, including pH, catalyst and H₂O₂ dosages, and 86.62% diclofenac removal was achieved. Diclofenac oxidation by ·OH and adsorbed oxygen species was the main mechanism for its removal in this Fenton-like system.