Granular reduced graphene oxide/Fe3O4 hydrogel for efficient adsorption and catalytic oxidation of p-perfluorous nonenoxybenzene sulfonate

Efficient photodegradation of perfluoroalkyl substances under visible light by hexagonal ZnIn2S4 nanosheets

Perfluoroalkyl substances (PFASs) are typical persistent organic pollutants, and their removal is urgently required but challenging. Photocatalysis has shown potential in PFASs degradation due to the redox capabilities of photoinduced charge carriers in photocatalysts. Herein, hexagonal ZnIn2S4 (ZIS) nanosheets were synthesized by a one-pot oil bath method and were well characterized by a series of techniques. In the degradation of sodium p-perfluorous nonenoxybenzenesulfonate (OBS), one kind of representative PFASs, the as-synthesized ZIS showed activity superior to P25 TiO2 under both simulated sunlight and visible-light irradiation. The good photocatalytic performance was attributed to the enhanced light absorption and facilitated charge separation. The pH conditions were found crucial in the photocatalytic process by influencing the OBS adsorption on the ZIS surface. Photogenerated e- and h+ were the main active species involved in OBS degradation in the ZIS system. This work confirmed the feasibility and could provide mechanistic insights into the degradation and defluorination of PFASs by visible-light photocatalysis.

Peroxymonosulfate-assisted photocatalysis system enhanced magnetic Fe3O4@P-C3N4 treatment of tetracycline wastewater: Multi-pathways mediated electrons migration to generate reactive species

Photocatalytic wastewater purification is essential for environmental remediation, but rapid carrier recombination and limited oxidative capacity hinder progress. This study proposes an innovative strategy by integrating homogeneous and heterogeneous electron acceptors into a g-C3N4-based photocatalytic system, significantly enhancing the multipath utilization of photogenerated electrons. A novel Fe3O4@P-C3N4 was developed to activate an advanced peroxymonosulfate-assisted photocatalysis (PAP) system, achieving complete degradation and significant mineralization of tetracycline (TC) in real water environments, outperforming others reported in the last five years. Phytic acid, as a key precursor, modifies the hollow tubular morphology and introduces phosphorus (P) heteroatoms as electronic trapping centers, enhancing the visible light response and carrier separation, thereby promoting the Fe2+/Fe3+ cycle and the formation of reactive species. Density functional theory (DFT) calculations pinpointed TC's vulnerable sites and synergically identified reactive species, revealing almost non-toxic degradation processes. Moreover, the recyclable magnetic Fe3O4@P-C3N4/PAP system demonstrates practical application potential and leaching stability in cyclic and continuous testing. This study offers unique insights into the strategic design of photocatalysts and catalytic environments, potentially advancing practical wastewater remediation.

Activation of persulfate with magnetic Fe3O4-municipal solid waste incineration bottom ash-derived zeolite core-shell materials for tetracycline hydrochloride degradation

A novel and environmentally friendly magnetic iron zeolite (MIZ) core-shell were successfully fabricated using municipal solid waste incineration bottom ash-derived zeolite (MWZ) coated with Fe3O4 and innovatively investigated as a heterogeneous persulfate (PS) catalyst. The morphology and structure composition of as-prepared catalysts were characterised, and it was proved that the core-shell structure of MIZ was successfully synthesised by coating Fe3O4 uniformly on the MWZ surface. The tetracycline hydrochloride (TCH) degradation experiment indicate that the optimum equimolar amount of iron precursors was 3 mmol (MIZ-3). Compared with other systems, MIZ-3 possessed a superior catalytic performance, and the degradation efficiency of TCH (50 mg·L-1) in the MIZ-3/PS system reached 87.3%. The effects of reaction parameters on the catalytic activity of MIZ-3, including pH, initial concentration of TCH, temperature, the dosage of catalyst, and Na2S2O8, were assessed. The catalyst had high stability according to three recycling experiments and the leaching test of iron ions. Furthermore, the working mechanism of the MIZ-3/PS system to TCH was discussed. The electron spin resonance (ESR) results demonstrated that the reactive radicals generated in the MIZ-3/PS system were sulphate radical (S O 4 - ∙ ) and hydroxyl radical (•OH). This work provided a novel strategy for TCH degradation under PS with a broad perspective on the fabrication of non-toxic and low-cost catalysts in practical wastewater treatment.

Amino Group-Driven Adsorption of Sodium p-Perfluorous Nonenoxybenzene Sulfonate in Water by the Modified Graphene Oxide

Sodium p-perfluorous nonenoxybenzene sulfonate (OBS) is one of the key alternatives to perfluoroalkyl substances (PFASs). Its widespread tendency has increased extensive contamination in the aquatic environment. However, the present treatment technology for OBS exhibited insignificant adsorption capacity and long adsorption time. In this study, three proportions (1:5, 3:5, and 10:1) of chitosan-modified amino-driven graphene oxide (CS-GO) were innovated to strengthen the OBS adsorption capacity, compared with graphene oxide (GO) and graphene (GH). Through the characterization of SEM, BET, and FTIR, it was discovered that CS was synthetized on GO surfaces successfully with a low specific surface area. Subsequently, batch single influence factor studies on OBS removal from simulated wastewater were investigated. The optimum removal efficiency of OBS could be achieved up to 95.4% within 2 h when the adsorbent was selected as CS-GO (10:1), the dosage was 2 mg, and the pH was 3. The addition of inorganic ions could promote the adsorption efficiency of OBS. In addition, CS-GO presented the maximum adsorption energy due to additional functional groups of -NH3, and electrostatic interaction was the foremost motive for improving the adsorption efficiency of OBS. Moreover, OBS exhibited the fastest diffusion coefficient in the CS-GO-OBS solution, which is consistent with the fitting results of adsorption kinetics.

Fabrication and characterization of a novel magnetic nanostructure based on pectin-cellulose hydrogel for in vitro hyperthermia during cancer therapy

Herein, a new magnetic nanobiocomposite based on a synthesized cross-linked pectin-cellulose hydrogel (cross-linked Pec-Cel hydrogel) substrate was designed and synthesized. The formation of the cross-linked Pec-Cel hydrogel with a calcium chloride agent and its magnetization process caused a new and efficient magnetic nanobiocomposite. Several spectral and analytical techniques, including FTIR, SEM, VSM, TGA, XRD, and EDX analyses, were performed to confirm and characterize the structural features of the magnetic cross-linked pectin-cellulose hydrogel nanobiocomposite (magnetic cross-linked Pec-Cel hydrogel nanobiocomposite). Based on SEM images, prepared Fe3O4 magnetic nanoparticles (MNPs) were uniformly dispersed in the Pec-Cel hydrogel context, representing an average particle size between 50.0 and 60.0 nm. The XRD pattern also confirms the crystallinity of the magnetic nanobiocomposite. All constituent elements and their distribution have been depicted in the EDX analysis of the magnetic nanobiocomposite. VSM curves confirmed the superparamagnetic behavior of Fe3O4 MNPs and the magnetic nanobiocomposite with a saturation magnetization of 77.31 emu g-1 and 48.80 emu g-1, respectively. The thermal stability of the nanobiocomposite was authenticated to ca. 800 °C based on the TGA thermogram. Apart from analyzing the structural properties of the magnetic cross-linked Pec-Cel hydrogel nanobiocomposite, different concentrations (0.5 mg mL-1, 1.0 mg mL-1, 2.0 mg mL-1, 5.0 mg mL-1, and 10.0 mg mL-1) of this new magnetic nanostructure were exposed to an alternating magnetic field (AMF) at different frequencies (100.0 MHz, 200.0 MHz, 300.0 MHz, and 400.0 MHz) to evaluate its capacity for an in vitro hyperthermia process; in addition, the highest specific absorption rate (126.0 W g-1) was obtained by the least magnetic nanobiocomposite concentration (0.5 mg mL-1).

Innovation of BiOBr/BiOI@Bi5O7I Ternary Heterojunction for Catalytic Degradation of Sodium P-Perfluorous Nonenoxybenzenesulfonate

As an alternative for perfluorooctane sulfonic acid (PFOS), sodium p-perfluorononyloxybenzene sulfonate (OBS) has been widely used in petroleum, fire-fighting materials, and other industries. In order to efficiently and economically remove OBS contaminations from water bodies, in this study, a ternary heterojunction was constructed by coupling BiOBr and BiOI@Bi5O7I for improving the redox capacity and carrier separation ability of the material and investigating the effect of the doping ratios of BiOBr and BiOI@ Bi5O7I on the performance of the catalysts. Furthermore, the effects on the degradation of OBS were also explored by adjusting different catalyst doping ratios, OBS concentrations, catalyst amounts, and pH values. It was observed that when the concentration of OBS was 50 mg/L, the amount of catalyst used was 0.5 g/L, and the pH was not changed. The application of BiOBr/BiOI@ Bi5O7I consisting of 25% BiOBr and 75% BiOI@ Bi5O7I showed excellent stability and adsorption degradation performance for OBS, and almost all of the OBS in the aqueous solution could be removed. The removal rate of OBS by BiOBr/BiOI@ Bi5O7I was more than 20% higher than that of OBS by BiOI@Bi5O7I and BiOBr when the OBS concentration was 100 mg/L. In addition, the reaction rate constants of BiOBr/BiOI@ Bi5O7I were 2.4 and 10.8 times higher than those of BiOI@ Bi5O7I and BiOBr, respectively. Therefore, the BiOBr/BiOI@ Bi5O7I ternary heterojunction can be a novel type of heterojunction for the efficient degradation of OBS in water bodies.

A graphene oxide-loaded processed pyritum composite hydrogel for accelerated bone regeneration via mediation of M2 macrophage polarization

A coordinated interaction between osteogenesis and the osteoimmune microenvironment plays a vital role in regulating bone healing. However, disturbances in the pro- and anti-inflammatory balance hinder the therapeutic advantages of biomaterials. In this study, a novel composite hydrogel was successfully fabricated using graphene oxide (GO)-loaded processed pyritum (PP) in combination with poly(ethylene glycol) diacrylate (PEGDA) and carboxymethyl chitosan (CMC). Subsequently, the immunomodulatory effects and bone regenerative potential of PP/GO@PEGDA/CMC were investigated. The results demonstrated that the PP/GO@PEGDA/CMC hydrogel possessed excellent mechanical properties, swelling capacity, and stability. Moreover, PP/GO@PEGDA/CMC prominently promoted M2 polarization and increased the levels of anti-inflammatory factors (interleukin (IL)-4, IL-10, and transforming growth factor-β). These beneficial effects facilitated the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells in vitro. Additionally, the in vivo results further verified that the implantation of PP/GO@PEGDA/CMC markedly reduced local inflammation while enhancing bone regeneration at 8 weeks post-implantation. Therefore, the results of this study provide potential therapeutic strategies for bone tissue repair and regeneration by modulating the immune microenvironment.

The novel polyfluoroalkyl benzenesulfonate OBS exposure induces cell cycle arrest and senescence of rat pituitary cell GH3 via the p53/p21/RB pathway

Sodium p-perfluorous nonenoxybenzene sulfonate (OBS), an economical alternative to perfluorooctane sulfonate (PFOS) in multiple industrial fields, is widely detected in the environment. The toxicity of OBS has received increasing attention. Pituitary cells are components of the endocrine system and act as vital regulators of homeostatic endocrine balance. However, the effects of OBS on pituitary cells remain unknown. The present study explores the effects of OBS (0.5, 5, and 50μM) on GH3 rat pituitary cells after treatment for 24, 48, and 72h. We found that OBS significantly inhibited cell proliferation in GH3 cells with remarkable senescent phenotypes, including enhanced SA-β-gal activity and expression of senescence-associated secretory phenotype (SASP)-related genes, cell cycle arrest, and upregulation of the senescence-related proteins γ-H2A.X and Bcl-2. OBS caused significant cell cycle arrest of GH3 cells at the G1-phase and concomitantly downregulated the expression of some key proteins for the G1/S transition, including cyclin D1 and cyclin E1. Consistently, the phosphorylation of retinoblastoma (RB), which plays a central role in regulating the cell cycle, was prominently reduced after OBS exposure. Furthermore, OBS notably activated the p53-p21 signalling pathway in GH3 cells, as evidenced by increased p53 and p21 expressions, enhanced p53 phosphorylation, and augmented p53 nuclear import. To our knowledge, this study is the first to reveal that OBS triggers senescence in pituitary cells via the p53-p21-RB signalling pathway. Our study demonstrates a novel toxic effect of OBS in vitro, and provides new perspectives for understanding the potential toxicity of OBS.

Efficient adsorption and degradation of dyes from water using magnetic covalent organic frameworks with a pyridinic structure

Covalent organic frameworks (COFs) have promising applications in environmental remediation owing to their precise directional synthesis and superior adsorption ability. However, magnetic COFs with pyridinic N have not been studied as bifunctional materials for the adsorption and catalytic degradation of dyes. Therefore, in this study, a magnetic COF with a pyridinic structure (BiPy-MCOF) was successfully synthesized using a solvothermal method, which exhibited higher methyl orange (MO) removal than other common adsorbents. The best degradation efficiency via the Fenton-like reaction was obtained by pre-adsorbing MO for 3 h at pH 3.1. Both adsorption and catalytic degradation resulted in better removal of MO under acidic conditions. The introduction of pyridinic N improved MO adsorption and degradation on BiPy-MCOF. The electrostatic potential (ESP) showed that pyridinic N had a strong affinity for MO adsorption. Density functional theory calculations confirmed the potential sites on MO molecules that may be attacked by free radicals. Possible degradation pathways were proposed based on the experimental results. Moreover, BiPy-MCOF could effectively degrade MO at least four times, and a high degradation efficiency was obtained in other dyes applications. The coupling of adsorption and degradation demonstrated that the as-prepared BiPy-MCOF was an effective material for organic dyes removal from water.

FeCl3-activated biochar catalyst for heterogeneous Fenton oxidation of antibiotic sulfamethoxazole in water

One-step FeCl₃-mediated pyrolysis/activation was developed for preparation of bermudagrass (BG)-derived FeCl₃-activated biochars (FA-BCs) from bermudagrass (BG) as a heterogenous Fenton catalyst for heterogeneous Fenton oxidation of sulfamethoxazole (SMX) in water. The FA-BC prepared at the FeCl₃ to BG mass ratio of 2 (FA-BC) exhibited higher adsorption and Fenton oxidation of SMX than other mass ratios of the FeCl₃ to BG. FA-BC presented the great surface area (835 m²/g) and high SMX adsorption capacity (195 mg SMX/g BC), which was higher than various BCs in the previous studies. Additionally, the surface of FA-BC was attached with Fe₂O₃, Fe⁰, and Fe₃O₄ after the FeCl₃ activation. Under the optimal conditions for Fenton reaction (SMX concentration, 100 mg/L; loading of FA-BC, 0.1 g/L; dose of H₂O₂, 200 mg/L; temperature, 20 °C; pH 3; reaction time, 12 h), SMX and COD removal efficiencies reached 99.94% and 65.19%, respectively. Increasing reaction temperature from 20 to 50 °C significantly improved the SMX oxidation rate from 0.46 to 1.04 h^-1. The HO· radicals were proved to play a major role during the Fenton oxidation of SMX. In addition, the SMX solution treated by Fenton oxidation showed much less toxicity than the initial SMX solution. Additionally, the reusability tests of FA-BC indicated that 89.58% removal efficiency for SMX was still achieved after 3 cycles of Fenton oxidation under the optimal conditions. Furthermore, FA-BC can also efficiently remove SMX from the dairy wastewater. Therefore, FA-BC showed a high potential to eliminate aqueous SMX through adsorption and heterogeneous Fenton oxidation.

Autoclave and pulsed ultrasound cavitation based thermal activation of persulfate for regeneration of hydrogen titanate nanotubes as recyclable dye adsorbent

In the dye removal application, regeneration of hydrogen titanate nanotubes (HTN, H₂Ti₃O₇) has been achieved via thermal activation of persulfate anion (PS, S₂O₈^2-) by using the conventional hot plate technique which has limitations from the commercial perspective since it does not provide any precise control over the thermal generation process typically during the scale-up operation. To overcome this drawback, HTN have been synthesized via hydrothermal process which exhibit the methylene blue (MB) adsorption of 93% at the initial dye concentration and solution pH of 90 µM and 10 respectively. HTN have been regenerated via the thermal activation of PS by varying its initial concentration and regeneration temperature, within the range of 0.27-1 wt% and 40-80 °C, under the thermal conditions set by the autoclave and pulsed ultrasound (US) cavitation process. The results of recycling experiments suggest that the optimum values of initial PS concentration and temperature, for the regeneration of HTN under the autoclave conditions, are 1 wt% and 70 °C with the maximum MB adsorption of 92%, while, the corresponding values for the pulsed US cavitation process are 1 wt%, 80 °C, and 91% respectively. Thus, the regeneration and recycling of HTN have been successfully demonstrated by using the autoclave and pulsed US cavitation process. Under the optimum conditions, MB degradation involves the generation and attack of SO₄^•- for both the thermal generation techniques. The regeneration techniques developed here may be utilized in future during the scale-up operation and also for the regeneration of adsorbents besides HTN.

Nanocellulose fine-tuned poly(acrylic acid) hydrogel for enhanced diclofenac removal

Hydrogel was recognized as one of the most promising materials for adsorption of pharmaceuticals and personal care products (PPCPs). The highly efficient bio-based nanocelluloses fine-tuned poly(acrylic acid) hydrogel (PAA/NC) adsorbent was constructed by adjusting aspect ratio, surface charge and crystallinity of NC. The cross-linked networks were fabricated through a single-step free-radical polymerization via steric effect and hydrogen bonds. The uniform three-dimensional structures with abundant macropores and mesopores were in-situ visualized by the cryogenic-scanning electron microscopy (Cryo-SEM). The diclofenac adsorption capacity of TEMPO oxidized cellulose nanofibers (TCNF) incorporated PAA hydrogel (PAA/TCNF, 559.8 mg·g^-1) was circa 2.1 times higher than pristine PAA (293.5 mg·g^-1) due to the elevated specific surface area, favorable spatial structure with unimpeded channels and abundant surface-charged carboxylic groups. Moreover, PAA/NC hydrogel exhibited a wide-pH applicability and high salinity tolerance. The adsorption was predominantly determined by hydrogen bonds, validated by XPS and FT-IR analysis. It was demonstrated developed PAA/NC hydrogel with unique porous structure significantly enhanced adsorption capacity for potential application in the purification of refractory organic pollutants-containing wastewater.

Tissue distribution of sodium p-perfluorous nonenoxybenzene sulfonate (OBS) in mice via oral exposure

Environmental risks caused by emerging per- and polyfluoroalkyl substances (PFASs) have attracted increasing attention. As an important substitute for perfluorooctane sulfonate (PFOS), sodium p-perfluorous nonenoxybenzene sulfonate (OBS) is widely used as a firefighting foam additive and oil recovery agent in China. This study reported the tissue distribution of OBS in KM mice that were administered a dose of OBS at 10 µg/day via daily oral gavage for 7, 14, or 28 days. During exposure, gender-based differences were observed in body weight changes and tissue distribution of OBS. Liver exhibited the highest concentrations (males: 12.57 ± 1.80 µg/g; females: 11.80 ± 5.32 µg/g) and tissue/blood ratios and contributed more than 50% to the whole-body burden of OBS in both male and female mice, showing its ability to enrich PFASs. Furthermore, there were certain differences in the distribution characteristics of the three OBS isomers. Based on its bioaccumulation potential and widespread use, further studies are required on the human exposure risks of OBS.

Degradation of OBS (Sodium p-Perfluorous Nonenoxybenzenesulfonate) as a Novel Per- and Polyfluoroalkyl Substance by UV/Persulfate and UV/Sulfite: Fluorinated Intermediates and Treatability in Fluoroprotein Foam

Sodium p-perfluorous nonenoxybenzenesulfonate (OBS) is a novel fluorosurfactant used as the alternative to perfluorooctanesulfonic acid (PFOS) in several applications such as fire-fighting foams and chemical enhanced oil recovery ("EOR") in China, with the annual production capacity of about 3,500 t. Here, for the first time, we investigated the degradability of OBS under the conditions of UV/persulfate (UV/PS) and UV/sulfite (UV/SF) as typical redox processes. A higher reaction rate (1.05 min^-1) and total organic carbon (TOC) reduction (46.9%) but a low defluorination rate (27.6%) along with the formation of a series of fluorinated intermediates were found in UV/PS, while a high defluorination rate (87.7%) was realized in UV/SF. In particular, a nontargeted workflow using high performance liquid chromatography-quadrupole time-of-flight mass spectrometry (HPLC/Q-TOF-MS) was established to detect fluorinated intermediates. Combined with the theoretical calculation, the distinctive degradation pathways in both oxidation and reduction processes were proposed. The degradation mechanism of OBS in UV/SF was proposed to be H/F exchange and subsequent HF elimination. Furthermore, the diluted OBS-based fluoroprotein (FP) foam was used to investigate the degradation of OBS, which confirms the treatability using the redox approach. This work provides insights into the degradability of OBS, fluorinated intermediate search, and proper treatment of related contamination.

Magnetic graphene oxide for methylene blue removal: adsorption performance and comparison of regeneration methods

A series of Fe₃O₄-graphene oxide (GO) composite materials (MGOs) with abundant surface area, rich oxygen-containing functional groups, and magnetic properties were prepared in a facile coprecipitation method and then employed for the adsorptive removal of methylene blue (MB) from water. The kinetic data were better fitted in the pseudo-second-order model than in the pseudo-first-order model, and the intraparticle diffusion model revealed the two-step diffusion process including diffusion in the boundary layer and in the porous structures. The maximum adsorption amounts of MB were calculated to be 37.5-108 mg/g at 25 °C and pH 9 using the Langmuir isotherm model. Thermodynamic study showed that the adsorption process was spontaneous, with ΔH° of 23.0-49.6 kJ/mol and ΔS° of 131-249 J∙mol^-1∙K^-1. The adsorption amount of MB increased with pH in the range of 4-10. Inorganic ions including Na⁺ and Ca²⁺ suppressed the adsorption of MB, and the more pronounced impact of Ca²⁺ was ascribed to its higher valence state. The cetyltrimethylammonium bromide (CTAB) surfactant showed a stronger inhibitory effect than Ca²⁺. The adsorption mechanism was proposed to be a combination of electrostatic interactions, hydrophobic adsorption, and electron donor-acceptor interactions. Two methods were used for the regeneration of spent MGO, and the results showed that the peroxomonosulfate (PMS) oxidation method was more favorable than the acid washing method, considering the better regeneration ability and lower amount of washing water used. Finally, the reaction mechanism of PMS oxidation was analyzed based on quenching tests and in situ open circuit potential measurements, which proved that OH and ¹O₂ played dominant roles and that the fine adsorption ability of MGO promoted the reaction between them and MB.

Carbon materials in persulfate-based advanced oxidation processes: The roles and construction of active sites

Many researchers have paid more attention to the progress of carbon materials owing to their advantages, such as high activity, low cost, large surface area, high conductivity and high stability. Carbon materials have been widely used in persulfate-based advanced oxidation processes (PS-AOPs), especially for graphene (G), carbon nanotubes (CNTs) and biochar (BC). Various strategies are applied to promote their activity, however, up to now, the relationship between the structures of carbon materials and their activities in PS-AOPs has not been specifically reviewed. The methods to switch reaction pathway (radical and nonradical pathways) in carbon-persulfate-based AOPs have not been systematically explored. Hereon, this review illustrated the active sites of G, CNTs, BC and other carbon materials, and generalized the modification methods to promote the activity of carbon materials and to switch reaction pathway in PS-AOPs. The roles of carbon materials in PS-AOPs were discussed around reactive oxygen species (ROS) and the structures. ROS are frequently complex in AOPs, but main ROS generation is related to the active sites on carbon materials. The structures of carbon materials (e.g., metal-carbon bonds, the electron-deficient C atoms, unbalanced electron distribution and graphitized structures) play a decisive role in the nonradical pathway. Finally, future breakthroughs of carbon materials were proposed for practical engineering and multi-field application.

Synergistic effects of oxidation, coagulation and adsorption in the integrated fenton-based process for wastewater treatment: A review

Fenton process is the most popular for wastewater treatment among all available advanced oxidation processes (AOPs). Numerous endeavors have been devoted to improving the oxidation efficiency of Fenton reaction in terms of promoting ·OH generation, accelerating iron redox cycle and extending applicable pH range. However, in addition to oxidation, coagulation and adsorption also simultaneously occur in the Fenton process, which play important role in the removal of pollutants. Rapid progress has revealed the synergistic effects of oxidation, coagulation and adsorption in the Fenton process, providing new ideas for the treatment of complex and refractory wastewater. Based on available studies, this review is the first to systematically summarize the research progress regarding the synergistic effects of oxidation, coagulation and adsorption in the integrated Fenton-based processes for wastewater treatment. The involved mechanism of the synergistic effects in different Fenton processes (homogeneous Fenton, heterogeneous Fenton and physical field-assistant Fenton coupling process) are critically reviewed. Furthermore, special attention has been paid to the representative applications of the synergistic effects in wastewater treatment (such as industrial organic wastewater, landfill leachate and heavy metal-organic complexes, etc.), particularly focusing on the operation parameters and removal performance. Finally, a conclusion of the review and subsequently, perspectives are given for possible research directions. We believe this review can provide useful information for researchers and end-users involved in the development and application of the Fenton process in wastewater treatment.

Efficient degradation of organic dyes using peroxymonosulfate activated by magnetic graphene oxide

Magnetic graphene oxide (MGO) was prepared and used as a catalyst to activate peroxymonosulfate (PMS) for degradation of Coomassie brilliant blue G250 (CBB). The effects of operation conditions including MGO dosage, PMS dosage and initial concentration of CBB were studied. CBB removal could reach 99.5% under optimum conditions, and high removals of 98.4–99.9% were also achieved for other organic dyes with varied structures, verifying the high efficiency and wide applicability of the MGO/PMS catalytic system. The effects of environmental factors including solution pH, inorganic ions and water matrices were also investigated. Reusability test showed that CBB removals maintained above 90% in five consecutive runs, indicating the acceptable recyclability of MGO. Based on quenching experiments, solvent exchange (H₂O to D₂O) and in situ open circuit potential (OCP) test, it was found that ˙OH, SO₄˙⁻ and high-valent iron species were responsible for the efficient degradation of CBB in the MGO/PMS system, while the contributions of O₂˙⁻, ¹O₂ and the non-radical electron-transfer pathway were limited. Furthermore, the plausible degradation pathway of CBB was proposed based on density functional theory (DFT) calculations and liquid chromatography-mass spectrometry (LC-MS) results, and toxicity variation in the degradation process was evaluated by computerized structure–activity relationships (SARs) using green algae, daphnia, and fish as indicator species.

Efficient degradation of organic dyes with PMS and magnetic graphene oxide.

Fast preparation of Fe3O4@polydopamine/Au for highly efficient degradation of tetracycline

This work reported the fast synthesis of magnetic polydopamine Au-Fenton catalyst (Fe₃O₄@PDA/Au) under UV irradiation at 365 nm. The microstructure of prepared nanocomposites was characterized by various techniques. The effects of several key factors (pH values, H₂O₂ content and TC concentration) of tetracycline (TC) degradation were evaluated. The results revealed that the TC and total organic carbon (TOC) removal rate reached up to 98.16% and 93.14% within 300 min under optimal conditions (pH 3, H₂O₂ 80 μL, TC concentration 20 mg/L). Besides, HO radicals were generated during the Fenton-like degradation process and the plausible degradation mechanism was discussed. Moreover, Fe₃O₄@PDA/Au catalyst retained excellent catalytic capacity (TC removal rate 96.94% and TOC removal rate 87.69%) and exhibited fantastic stability after six cycles. Moreover, metal ions leaching was evaluated (0.023 mg/L). Altogether, the novel Fe₃O₄@PDA/Au Fenton-like catalyst is highly promising for wastewater management.

Toward Selective Oxidation of Contaminants in Aqueous Systems

The presence of diverse pollutants in water has been threating human health and aquatic ecosystems on a global scale. For more than a century, chemical oxidation using strongly oxidizing species was one of the most effective technologies to destruct pollutants and to ensure a safe and clean water supply. However, the removal of increasing amount of pollutants with higher structural complexity, especially the emerging micropollutants with trace concentrations in the complicated water matrix, requires excessive dosage of oxidant and/or energy input, resulting in a low cost-effectiveness and possible secondary pollution. Consequently, it is of practical significance but scientifically challenging to achieve selective oxidation of pollutants of interest for water decontamination. Currently, there are a variety of examples concerning selective oxidation of pollutants in aqueous systems. However, a systematic understanding of the relationship between the origin of selectivity and its applicable water treatment scenarios, as well as the rational design of catalyst for selective catalytic oxidation, is still lacking. In this critical review, we summarize the state-of-the-art selective oxidation strategies in water decontamination and probe the origins of selectivity, that is, the selectivity resulting from the reactivity of either oxidants or target pollutants, the selectivity arising from the accessibility of pollutants to oxidants via adsorption and size exclusion, as well as the selectivity due to the interfacial electron transfer process and enzymatic oxidation. Finally, the challenges and perspectives are briefly outlined to stimulate future discussion and interest on selective oxidation for water decontamination, particularly toward application in real scenarios.

Activation of inorganic peroxides with magnetic graphene for the removal of antibiotics from wastewater

Magnetic graphene catalysts were prepared for the removal of antibiotics (sulfamethoxazole, norfloxacin, tetracycline and flumequine) from water. Different proportions of magnetite-graphene from 1:0 to 0:1 were considered to study the catalytic activation of inorganic peroxides, i.e. peroxymonosulfate (PMS), peroxydisulfate and hydrogen peroxide. The presence of graphene was mainly responsible for the activation, which was most effective in the presence of PMS. A ratio of 20% of magnetite in the solid was enough to achieve complete degradation of antibiotics with high recovery by application of a magnetic field. The performance of the catalyst was further evaluated in a simulated urban wastewater, studying the main parameters affecting the process and the stability in sequential reuses. The non-radical mechanism during the catalytic activation of PMS was hypothesized from kinetic scavenging probes tests. The electron transfer was suggested as the mechanism of the reaction from electron paramagnetic resonance analysis in the presence of D₂O. The prepared magnetic catalyst showed high catalytic activity and stability to remove antibiotics from water.

Self-Assembled Nano-Fe3C Embedded in Reduced Graphene Oxide Aerogel with Efficient Fenton-Like Catalysis

Aiming at the removal of refractory organic pollutants in aqueous solution, self-assembled nano-Fe3C embedded in reduced graphene oxide (nano-Fe3C@RGO) aerogel was prepared by hydrothermal synthesis and high temperature treatment, and characterized by SEM, HRTEM, pore size distribution, XRD, XPS and FTIR. The results showed that the aerogel was porous, and most of the Fe3C particles were less than 100 nm in size. They were evenly dispersed and embedded in the RGO aerogel. Furthermore, the mapping images confirmed that the elements of carbon, nitrogen and iron were homogeneously distributed. Moreover, the specific surface area of the aerogel was up to 324.770 m2/g and most of the pore sizes were between 5 and 10 nm. The formation of nano-Fe3C was identified by XRD pattern and HRTEM. Analysis of an XPS spectrum indicates that the nano-Fe3C was embedded in the graphene layer. The aerogel contained a large number of functional groups, including -NH2-NH and -C=O, etc., which greatly strengthened the adsorption of organics. Finally, the Fenton-like catalytic degradation properties of the self-assembled nano-Fe3C@RGO aerogel were investigated by testing the removal of methyl orange from the aqueous solution. The results showed that the value of Ct/C0 decreased to 0.050 after 240 min, suggesting a high degradation rate was obtained. Meanwhile, the chemical reaction was verified in accordance with the first-order kinetic model, and the higher temperature was beneficial to the catalytic degradation. At the same time, methyl orange was degraded into small molecules by the hydroxyl and superoxide radicals generated during the reactions. Therefore, the self-assembled nano-Fe3C@RGO aerogel, as a novel Fenton-like catalyst, introduces a new approach in the field of treatment of refractory organic wastewater.