Ultrahigh-sensitive mixed-potential ammonia sensor using dual-functional NiWO4 electrocatalyst for exhaust environment monitoring

Synergistic Enhancement on the Sensing Performance of Mixed Potential NH3 Sensors by Fe and Mo Codoping into BiVO4

Mixed potential ammonia (NH3) sensors with the Fe- and Mo-codoped BiVO4 sensing electrode and Ag reference electrode based on the yttria-stabilized zirconia solid electrolyte were developed. Fe- and Mo-doped BiVO4 sensing materials were prepared using solution combustion synthesis and then characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). It was observed that Fe doping could greatly improve the response rate, while Mo doping could enhance the response signal (ΔU) and sensitivity. Based on the optimal doping ratio of Fe and Mo each, the synergistic enhancement of the performance by Fe and Mo codoping was investigated. The sensor coated by BiV0.75Fe0.2Mo0.05Oδ materials exhibited a prominent sensing performance to a low concentration of 10-50 ppm of NH3 at 525 °C with the outstanding sensitivity of -148.988 mV/decade. Fe and Mo doping also improved the selectivity of the sensor to NH3, with the relative deviations less than ±8% of other typical gases' interference including NO, NO2, CO, CO2, and CH4. Besides, the sensor showed good resistance to fluctuations in the oxygen concentration and favorable stability against changes in the water vapor concentration. In addition, the sensor also exhibited good long-term stability. The mixed potential response mechanism was further discussed and analyzed through polarization curves as well as through gas chromatography and infrared absorption spectroscopy.

Control interfacial charge transfer behavior by creating surface defects on structure unit of heterojunction to drive carrier separation for enhancing photocatalytic CO2 reduction

Controlling interfacial charge transfer behavior of heterojunction is an arduous issue to efficiently drive separation of photogenerated carriers for improving the photocatalytic activity. Herein, the interface charge transfer behavior is effectively controlled by fabricating an unparalleled VO-NiWO4/PCN heterojunction that is prepared by encapsulating NiWO4 nanoparticles rich in surface oxygen vacancies (VO-NiWO4) in the mesoporous polymeric carbon nitride (PCN) nanosheets. Experimental and theoretical investigations show that, differing with the traditional p-n junction, the direction of built-in electric field between p-type NiWO4 and n-type PCN is reversed interestingly. The strongly codirectional built-in electric field is also produced between the surface defect region and inside of VO-NiWO4 besides in the space charge region, the dual drive effect of which forcefully propels interface charge transfer through triggering Z-Scheme mechanism, thus significantly improving the separation efficiency of photogenerated carriers. Moreover, the unique mesoporous encapsulation structure of VO-NiWO4/PCN heterostructure can not only afford the confinement effect to improve the reaction kinetics and specificity in the CO2 reduction to CO, but also significantly reduce mass transfer resistance of molecular diffusion towards the reaction sites. Therefore, the VO-NiWO4/PCN heterostructure demonstrates the preeminent activity, stability and reusability for photocatalytic CO2 reduction to CO reaction. The average evolution rate of CO over the optimal 10 %-VO-NiWO4/PCN composite reaches around 2.5 and 1.8 times higher than that of individual PCN and VO-NiWO4, respectively. This work contributes a fresh design approach of interface structure in the heterojunction to control charge transfer behaviors and thus improve the photocatalytic performance.

Mixed-Potential Ammonia Sensor Based on a Dense Yttria-Stabilized Zirconia Film Manufactured at Room Temperature by Powder Aerosol Deposition

Powder aerosol deposition (often abbreviated as PAD, PADM, or ADM) is a coating method used to obtain dense ceramic films at room temperature. The suitability of this method to obtain ammonia mixed-potential sensors based on an yttria-stabilized zirconia (YSZ) electrolyte that is manufactured using PAD and a V2O5-WO3-TiO2 (VWT)-covered electrode is investigated in this study. The sensor characteristics are compared with data from sensors with screen-printed YSZ solid electrolytes. The PAD sensors outperform those in terms of sensitivity with 117 mV/decade NH3 compared to 88 mV/decade. A variation in the sensor temperature shows that the NH3 sensitivity strongly depends on the sensor temperature and decreases with higher sensor temperature. Above 560 °C, the characteristic curve shifts from exponential to linear dependency. Variations in the water and the oxygen content in the base gas (usually 10% oxygen, 2% water vapor in nitrogen) reveal a strong dependence of the characteristic curve on the oxygen content. Water vapor concentration variations barely affect the sensor signal.

Tailoring the microstructure of BiVO4 sensing electrode by nanoparticle decoration and its effect on hazardous NH3 sensing

Real-time monitoring and quantification of exhaust pollutants is crucial but is troublesome because of extremely harsh thermochemical conditions, and in this regard mixed-potential sensing technology can be a realistic solution. In this study, BiVO₄ nanoparticles are decorated onto the preformed porous sensing electrode (SE) backbone by homogeneous infiltration process to improve the sensing performance in mixed-potential sensor. The influence of nanoparticle decoration on phase composition, microstructure and sensing performance are analyzed by physical and electrochemical techniques. Corresponding results indicate that the microstructure tailoring enhances the sensor performance, by extending the triple phase boundary (TPB) and surface area of SE itself. The sensitivity (-119.47 mV/decade) and response time (20 s) of i-BVO SE-based sensor at 600 ℃ are 20 % higher and 8 s faster than bare BiVO₄ SE-based sensor (99.24 mV/decade and 28 s). Additionally, the i-BVOǀYSZǀPt cell exhibits good selectivity and cross-sensitivity toward NH₃ without any dependency on oxygen partial pressure (pO₂). The fabricated sensor is also found stable towards cyclic and long-term operations. Electrochemical Impendence Spectroscopy (EIS) and DC polarization studies were performed to confirm the mixed-potential behavior. Conclusively, the superior sensing performance of i-BVO SE compared to various oxide based SEs highlights its suitability for mixed-potential NH₃ sensing.

Electrochemical detection of simple alkanes by utilizing a solid-state zirconia-based gas sensor

Solid-state gas sensors composed of complex oxide electrolytes offer great potential for analyzing various atmospheres at high temperatures. While relatively simple gas mixtures (H2O+N2, O2+N2) have been successfully studied by means of ZrO2-based sensors, the precise detection of more complex compounds represents a challenging task. In this work, we present our findings regarding the analysis of lower alkanes (CH4, C2H6, and C3H8) mixed with nitrogen as an inert gas, utilizing an amperometric ZrO2-based sensor. This sensor, serving as an electrochemical cell with a diffusion barrier, was tested at 500–600 °C to measure the limiting current, which depends on the gas composition and can be further used as a basis for calibration curves. In addition, the diffusion coefficients of the specified gas mixtures were successfully found and compared with references, confirming the applicability of the fabricated sensor for studying diffusion processes in wide concentration and temperature ranges.

Mixed potential type sensor based on Gd2Zr2O7 solid electrolyte and BiVO4 sensing electrode for effective detection of triethylamine

Triethylamine (TEA), as a common and widely used industrial raw material, is extremely hazardous to the environment and human health. Therefore, the development of a portable gas-sensing technology for high-efficiency detection of TEA is of great worth for human health and environmental monitoring. In this work, a mixed potential type TEA sensor was initially developed based on pyrochlore Gd₂Zr₂O₇ solid state electrolyte and BiVO₄ sensing electrode. The sensor generates high response values of - 62.2 mV and - 134.4 mV to 5 ppm and 100 ppm TEA at 500 °C, respectively. The response value of the sensor displays a logarithmic linear relationship with the concentration of TEA in the range of 1-100 ppm with the sensitivity of - 50.8 mV/decade. Besides, the sensor shows good response and recovery characteristics, and the response and recovery time to 10 ppm TEA is 10 s and 89 s, respectively. Moreover, the sensor possesses good humidity resistance, reproducibility and stability. The sensing behavior of the sensor is explained by the mixed potential sensing mechanism, which is confirmed by the measurement of the polarization curves. This work provides a good supplement for TEA gas sensor, which holds important application value for the sensitive detection of TEA in the environment.

Promoted Carbon Monoxide Sensing Performance of a Bi2Mn4O10-Based Mixed-Potential Sensor by Regulating Oxygen Vacancies

The YSZ-based mixed-potential sensor has exhibited promising application prospects for in situ carbon monoxide (CO) monitoring owing to its excellent thermal stability. However, the way to further enhance the sensitivity and selectivity of the sensor remains challenging due to the limitation of the sensing material. In the present work, we proposed a strategy of introducing moderate oxygen vacancies in the transition metal oxide sensing material to enhance CO sensing performance. More importantly, the oxygen vacancies of the sensing electrode were regulated by adjusting the volatilization of the Bi element at different sintering temperatures. Meanwhile, the stable mullite structure and variable valency of Mn were also exploited to maintain the phase structure stability and charge balance brought by the loss of Bi. The relationship between CO sensing properties and the proportion of both Mn³⁺/Mn⁴⁺ and oxygen vacancies was elucidated from XPS and EIS measurements. By contrast, the 800 °C-sintered Bi₂Mn₄O₁₀ possesses the highest oxygen vacancy content and thus exhibits preferable sensing performance including a lower detecting limit (10 ppm), swifter response/recovery processes, and enhanced CO sensitivity (-70.47 mV/decade operated at 450 °C) with satisfactory selectivity and stability, indicating a promising prospect for CO monitoring under exhaust environments.

Amorphous nickel tungstate films prepared by SILAR method for electrocatalytic oxygen evolution reaction

Development of electrocatalyst using facile way from non-noble metal compounds with high efficiency for effective water electrolysis is highly demanding for production of hydrogen energy. Nickel based electrocatalysts were currently developed for electrochemical water oxidation in alkaline pH. Herein, amorphous nickel tungstate (NiWO₄) was synthesized using the facile successive ionic layer adsorption and reaction method. The films were characterized by X-ray diffraction, Raman spectroscopy, Fourier transfer infrared spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy techniques. The electrochemical analysis showed 315 mV of overpotential at 100 mA cm^-2 with lowest Tafel slope of 32 mV dec^-1 for oxygen evolution reaction (OER) making films of NiWO₄ compatible towards electrocatalysis of water in alkaline media. The chronopotentiometry measurements at 100 mA cm^-2 over 24 h showed 97% retention of OER activity. The electrochemical active surface area (ECSA) of NW120 film was 25.5 cm^-2.

NiWO4 Microflowers on Multi-Walled Carbon Nanotubes for High-Performance NH3 Detection

NiWO4 microflowers with a large surface area up to 79.77 m2·g-1 are synthesized in situ via a facile coprecipitation method. The NiWO4 microflowers are further decorated with multi-walled carbon nanotubes (MWCNTs) and assembled to form composites for NH3 detection. The as-fabricated composite exhibits an excellent NH3 sensing response/recovery time (53 s/177 s) at a temperature of 460 °C, which is a 10-fold enhancement compared to that of pristine NiWO4. It also demonstrates a low detection limit of 50 ppm; the improved sensing performance is attributed to the porous structure of the material, the large specific surface area, and the p-n heterojunction formed between the MWNTs and NiWO4. The gas sensitivity of the sensor based on daisy-like NiWO4/MWCNTs shows that the sensor based on 10 mol % (MWN10) has the best gas sensitivity, with a sensitivity of 13.07 to 50 ppm NH3 at room temperature and a detection lower limit of 20 ppm. NH3, CO2, NO2, SO2, CO, and CH4 are used as typical target gases to construct the NiWO4/MWCNTs gas-sensitive material and study the research method combining density functional theory calculations and experiments. By calculating the morphology and structure of the gas-sensitive material NiWO4(110), the MWCNT load samples, the vacancy defects, and the influence law and internal mechanism of gas sensitivity were described.

Heterostructural (Sr0.6Bi0.305)2Bi2O7/ZnO for novel high-performance H2S sensor operating at low temperature

Exploring novel sensing materials enabling selective discrimination of trace ambient H₂S at lower temperature is of utmost importance for diverse practical applications. Herein, heterostructural (Sr_0.6Bi_0.305)₂Bi₂O₇/ZnO (SBO/ZnO) nanomaterials were proposed. Synergetic effect of promoting analyte adsorption (via multiplying oxygen vacancy defects) and reversible sulfuration-desulfuration reaction induced unique band alignment among SBO/ZnO/ZnS, contributes to the sensitive and selective response toward H₂S molecules. Novel SBO/ZnO (10%) sensor possesses excellent sensing H₂S performances, including a high response (107.6 for 10 ppm), low limit of detection of 20 ppb, good selectivity and long-term stability. Together with the merits of low operation temperature of 75 °C and weak humidity dependence (endowed by the hydrophobic SBO), present heterostructural SBO/ZnO sensor paves the way for the practical monitoring of trace H₂S pollutants in diverse workplaces including petroleum and natural gas industries.