Double-side microcantilevers as a key to understand the adsorption mechanisms and kinetics of chemical warfare agents on vertically-aligned TiO2 nanotubes

Mechanically Enhanced Detoxification of Chemical Warfare Agent Simulants by a Two-Dimensional Piezoresponsive Metal-Organic Framework

Chemical warfare agents (CWAs) refer to toxic chemical substances used in warfare. Recently, CWAs have been a critical threat for public safety due to their high toxicity. Metal-organic frameworks have exhibited great potential in protecting against CWAs due to their high crystallinity, stable structure, large specific surface area, high porosity, and adjustable structure. However, the metal clusters of most reported MOFs might be highly consumed when applied in CWA hydrolysis. Herein, we fabricated a two-dimensional piezoresponsive UiO-66-F4 and subjected it to CWA simulant dimethyl-4-nitrophenyl phosphate (DMNP) detoxification under sonic conditions. The results show that sonication can effectively enhance the removal performance under optimal conditions; the reaction rate constant k was upgraded 45% by sonication. Moreover, the first-principle calculation revealed that the band gap could be further widened with the application of mechanical stress, which was beneficial for the generation of 1O2, thus further upgrading the detoxification performance toward DMNP. This work demonstrated that mechanical vibration could be introduced to CWA protection, but promising applications are rarely reported.

Microcantilever-Based In Situ Temperature-Programmed Desorption (TPD) Technique

Temperature-programmed desorption (TPD) is an essential technique for characterizing the fundamental properties of advanced catalysts like catalytic activity and kinetics. However, the available TPD instruments are bulky and use ex situ detectors to measure the probe molecules in the elution gas flow. Herein, we demonstrate an in situ TPD technique by developing a silicon microcantilever that integrates functional elements for mass measuring and programmable sample heating. An only nanogram-level sample is required to load on the microcantilever free end, where the integrated microheater provides programmed temperatures and the desorption-induced mass change can be measured in situ. In situ TPD can continuously measure the number of desorbed molecules from the catalyst during programmed heating, without the need for ex situ detectors. With a single-time in situ TPD measurement, the desorption activation energy can be directly calculated. The proposed in situ TPD method outperforms the existing TPD techniques and is expected to enable next-generation TPD applications.

Fluorophenol-Containing Hydrogen-Bond Acidic Polysiloxane for Gas Sensing-Synthesis and Characterization

In this work, the synthesis of a new polysiloxane, poly {dimethylsiloxane-co-[4-(2,3-difluoro-4-hydroxyphenoxy) butyl] methylsiloxane} (dubbed PMFOS), is presented. This polymer exhibits high hydrogen bond acidity and was designed to be used as a sensor layer in gas sensors. The description of the synthetic route of the PMFOS has been divided into two main stages: the synthesis of the functional substituent 4-(but-3-en-1-yloxy)-2,3-difluorophenol, and the post-polymerization functionalization of the polysiloxane chain (methylhydrosiloxane-dimethylsiloxane copolymer) via hydrosilylation. The synthesized material was subjected to instrumental analysis, which confirmed its structure. The performed thermal analysis made it possible to determine some properties important for the sensor application, such as glass transition temperature and decomposition temperature. The results showed that PMFOS meets the requirements for materials intended for use in gas sensors based on acoustoelectric transducers.

Magnesium/aluminum layered double hydroxides intercalated with starch for effective adsorptive removal of anionic dyes

In this research, the adsorptive performance of a starch-magnesium/aluminum layered double hydroxide (S-Mg/Al LDH) composite was investigated for different organic dyes in single-component systems by conducting a series of batch mode experiments. S-Mg/Al LDH composite showed preferential adsorption of anionic dyes than cationic dyes. The marked impact of key process variables (e.g., contact time, adsorbent dosage, pH, and temperature) on its adsorption was investigated. Multiple isotherms, kinetics, and thermodynamic models were applied to describe adsorption behavior, diffusion, and uptake rates of the organic dyes over S-Mg/Al LDH composite. A better fitting of the non-linear Langmuir model reflects the predominance of monolayered adsorption of dye molecules on the composite surface. Partition coefficients (mg g^-1 μM^-1) for S-Mg/Al LDH were observed in the following descending order: Amaranth (665) > Tartrazine (186) > Sunset yellow (71) > Eosin yellow (65). Furthermore, comparative evaluation of the adsorption enthalpy, entropy, and Gibbs free energy values indicates that the adsorption process is spontaneous and exothermic. S-Mg/Al LDH composite maintained a stable adsorption/desorption recycling process over six consecutive cycles with the advantages of low cost, chemical/mechanical stability, and easy recovery. The results of this study are expected to expand the application of modified LDHs toward wastewater treatment.

3D Core-Shell TiO2@MnO2 Nanorod Arrays on Microcantilevers for Enhancing the Detection Sensitivity of Chemical Warfare Agents

Nanostructured microcantilevers have shown promise for sensing application of molecules in the vapor phase. Nanostructures have improved the molecule capture ability of microcantilevers by highly enhancing the surface of capture. Here, to improve the sensitivity and selectivity of a commercial microcantilever without functionalization, we developed 3D core-shell titanium dioxide@manganese dioxide (TiO₂@MnO₂) nanorod arrays on a microcantilever, which exhibited a high enhancement in the sensing performance beyond that of 1D nanostructures for the detection of dimethyl methylphosphonate, a simulant of sarin.

Quantitative Structure-Activity Relationship of Nanowire Adsorption to SO2 Revealed by In Situ TEM Technique

A quantitative structure-activity relationship (QSAR) is revealed based on the real-time sulfurization processes of ZnO nanowires observed via gas-cell in situ transmission electron microscopy (in situ TEM). According to the in situ TEM observations, the ZnO nanowires with a diameter of 100 nm (ZnO-100 nm) gradually transform into a core-shell nanostructure under SO₂ atmosphere, and the shell formation kinetics are quantitatively determined. However, only sparse nanoparticles can be observed on the surface of the ZnO-500 nm sample, which implies a weak solid-gas interaction between SO₂ and ZnO-500 nm. The QSAR model is verified with heat of adsorption (-ΔH°) and aberration-corrected TEM characterization. With the guidance of the QSAR model, the following adsorbing/sensing applications of ZnO nanomaterials are explored: (i) breakthrough experiment demonstrates the application potential of the ZnO-100 nm sample for SO₂ capture/storage; (ii) the ZnO-500 nm sample features good reversibility (RSD = 1.5%, n = 3) for SO₂ sensing, and the detection limit reaches 70 ppb.