Selective adsorption and ultrafast fluorescent detection of Cr(VI) in wastewater using neodymium doped polyaniline supported layered double hydroxide nanocomposite

Efficient selective adsorption of Cr(VI) by S-doped porous carbon prepared from industrial lignin: Waste increment and wastewater treatment

Industrial lignin is a waste product of the paper industry, which contains a large amount of oxygen group structure, and can be used to treat industrial wastewater containing Cr(VI). However, lignin has very low reactivity, so how to enhance its adsorption performance is a major challenge at present. In this study, a two-stage hydrothermal and activation strategy was used to activate the lignin activity and doping S element to prepare high-performance S-doped lignin-based polyporous carbon (S-LPC). The results show that the surface of S-LPC is rich in S and O groups and has a well-developed pore structure, which is very beneficial to Cr(VI) uptake -reduction and mass transfer on the material. In the wastewater, the utmost adsorption potential of Cr(VI) by S-LPC achieved 882.83 mg/g. After 7 cycles of regeneration, the adsorption of S-LPC decreased by only approximately 18 %. Ion competition experiments showed that S-LPC has excellent specificity for Cr(VI) adsorption. In factory wastewater, the adsorption performance of S-LPC for Cr(VI) remained above 95 %, which shows the excellent performance of S-LPC in practical applications. The results are of great significance for green chemical utilization of waste lignin, treatment of industrial wastewater and sustainable development.

Simple fluorochromic detection of chromium with ascorbic acid functionalized luminescent Bio-MOF-1

The bioaccumulation of various heavy metals in the environment and agriculture is posing serious hazards to human health. Hexavalent chromium is one of the most encountered heavy metal pollutants. The routine monitoring of Cr(VI) via simple methods assumes great analytical significance in sectors like environmental safety, food quality, etc. This study reports a novel biocompatible and luminescent metal-organic framework (ascorbic acid functionalized Bio-MOF-1) based "Turn-on" nanoprobe for rapid and sensitive optical detection of Cr(VI). Bio-MOF-1 has been synthesized, functionalized with ascorbic acid (AA), and then comprehensively characterized for its key material properties. The presence of Cr(VI) results in the photoluminescence recovery of Bio-MOF-1/AA. Using the above approach, Cr(VI) is detected over a wide concentration range of 0.02 to 20 ng mL-1, with the limit of detection being 0.01 ng mL-1. The nanoprobe is capable of detecting Cr(VI) in real water as well as in some spiked food samples. Hence, the ascorbic acid functionalized Bio-MOF-1 nanoprobe is established as a potential on-field detection tool for Cr(VI).

Insight into the interaction of 5,6 epoxy-cholesterols with human serum albumin

5,6-Epoxy-cholesterols has been recently revealed to control metabolic pathway in breast cancer, which makes investigating their binding interaction with human serum albumin (HSA) an attractive field of research. The main aim of this article is to examine the binding interaction of 5,6 α-epoxy-cholesterol (5,6 α EC) and 5,6 β-epoxy-cholesterol (5,6 β- EC) with HSA using different spectroscopic methods and molecular modeling. These compounds interact with HSA via hydrophobic interactions and hydrogen bonds with binding constants 6.3 × 105 M-1 for 5,6 α-epoxy-cholesterol and 6.9 × 105 M-1 for 5,6 β-epoxy-cholesterol besides, the mechanism of the interaction can be attributed to static quenching. Circular dichroism data indicated that the α-helical content of HSA increased from 50.5 to 59.8 and 61.1 % after the addition of 5,6 α-ECs and 5,6 β-EC, respectively, with a ratio of 1:2. Thermodynamic analysis revealed that binding between 5,6-epoxy-cholesterols and HSA is spontaneous and entropy-driven. The molecular docking and esterase-like activity experiments were performed to envision a link between the experimental and theoretical results. The optimal binding site of 5,6-epoxy-cholesterols with HSA was located in subdomain IIA. Moreover, theoretical calculations were performed using the B3LYP function with the 6-311++G (d,p) basis set, indicating the HOMO-LUMO energy gap of 7.874 eV for 5,6 α-epoxy-cholesterol and 7.873 eV for 5,6 β-epoxy-cholesterol. The obtained findings are assumed to provide basic data for understanding the binding interactions of HSA with oxysterol compounds, which could help explore the pharmacokinetics and pharmacodynamics of oxysterol compounds.

A Multimode Optical Sensor for Selective and Sensitive Detection of Harmful Heavy Metal Cr(VI) in Fresh Water and Sea Water

Water pollution originating from heavy metals has shown great impacts on the ecological environment and human health due to their extremely low biodegradability. Hexavalent chromium Cr(VI), as one harmful heavy metal with strong oxidation, high biological permeability, and high carcinogenicity, is becoming an increasingly serious threat to human health. Therefore, conveniently but accurately, monitoring the Cr(VI) level in water to maintain its normal level and ensuring the stability of the ecosystem and human health become very valuable. However, most of these heavy metal sensors reported are turn-off type single-emission sensors. In this work, a ratiometric fluorescence/colorimetry/smartphone triple-mode turn-on optical sensor for Cr(VI) was developed based on a multifunctional metal-organic framework platform. The detection limits for these three mutual verification modes were only 1.28, 4.89, and 68.4 nM, respectively. Additionally, the color changes of the detection system under sunlight can also be observed directly by the naked eye. The accuracy and practicability of this multimode sensor were further proved by the detection of Cr(VI) in actual water and seawater samples, and the recovery rate ranged from 97.308 to 104.041%.

Rapid and facile preparation of NiFe-layered double hydroxide nanosheets as self-supported electrode for glucose detection in drink sample

Layered double hydroxides have been widely used for electrochemical glucose detection due to their layered structure with more active sites, but they suffer from lower electrical conductivity and long-time hydrothermal preparation. In this paper, NiFe-layered double hydroxide nanosheets supported on nickel foam (NiFe-LDH NSs/NF) was prepared using an ultrafast and facile method via in-situ corroding foam nickel in FeCl3 solution under room temperature, and the whole synthetic process can be accomplished within several minutes. The as-fabricated NiFe-LDH NSs/NF shows significant catalytic activity in the glucose oxidation, showing its great promise in glucose detection. As a self-supported electrode, NiFe-LDH NSs/NF is favorable for glucose detection, with a sensitivity of 9.79 and 3.29 mA mM-1 cm-2 within the linear range of 0.001 to 1.16 mM and 1.16 to 4.67 mM, respectively. Moreover, NiFe-LDH NSs/NF is also selective and reliable towards glucose detection in drink sample.

Unveiling the contemporary progress of graphene-based nanomaterials with a particular focus on the removal of contaminants from water: a comprehensive review

Water scarcity and pollution pose significant challenges to global environmental sustainability and public health. As these concerns intensify, the quest for innovative and efficient water treatment technologies becomes paramount. In recent years, graphene-based nanomaterials have emerged as frontrunners in this pursuit, showcasing exceptional properties that hold immense promise for addressing water contamination issues. Graphene, a single layer of carbon atoms arranged in a hexagonal lattice, exhibits extraordinary mechanical, electrical, and chemical properties. These inherent characteristics have led to a surge of interest in leveraging graphene derivatives, such as graphene oxide (GO), reduced graphene oxide and functionalized graphene, for water treatment applications. The ability of graphene-based nanomaterials to adsorb, catalyze, and photocatalyze contaminants makes them highly versatile in addressing diverse pollutants present in water sources. This review will delve into the synthesis methods employed for graphene-based nanomaterials and explore the structural modifications and functionalization strategies implemented to increase their pollutant removal performance in water treatment. By offering a critical analysis of existing literature and highlighting recent innovations, it will guide future research toward the rational design and optimization of graphene-based nanomaterials for water decontamination. The exploration of interdisciplinary approaches and cutting-edge technologies underscores the evolving landscape of graphene-based water treatment, fostering a path toward sustainable and scalable solutions. Overall, the authors believe that this review will serve as a valuable resource for researchers, engineers, and policymakers working toward sustainable and effective solutions for water purification.

Smart fluorescent polysaccharides: Recent developments and applications

Polysaccharides are ubiquitous, generally benign in nature, and compatible with many tissues in biomedical situations, making them appealing candidates for new materials such as therapeutic agents and sensors. Fluorescent labeling can create the ability to sensitively monitor distribution and transport of polysaccharide-based materials, which can for example further illuminate drug-delivery mechanisms and therefore improve design of delivery systems. Herein, we review fluorophore selection and ways of appending polysaccharides, utility of the product fluorescent polysaccharides as new smart materials, and their stimulus-responsive nature, with focus on their biomedical applications as environment-sensitive biosensors, imaging, and as molecular rulers. Further, we discuss the advantages and disadvantages of these methods, and future prospects for creation and use of these self-reporting materials.

Microwave-assisted synthesis of amphoteric fluorescence carbon quantum dots and their chromium adsorption from aqueous solution

The chromium adsorption behavior from aqueous solution by the amphoteric Janus nitrogen-doped carbon quantum dots (AJ-N-CQDs) was investigated. The pseudo-first-order and the second-order adsorption kinetics models were employed to analyze the experimental data; the second-order adsorption kinetics model presented a better correlation to the experimental data, suggesting a chemisorptions process. The values obtained in the pseudo-first-order are still suitable for describing the Kinetics of Cr(VI) sorption. These values elucidate the surface processes involving chemisorption and physisorption in the adsorption of Cr(VI) by AJ-N-CQDs. The R² of the Boyd model gave a better fit to the adsorption data of AJ-N-CQDs (i.e., external diffusion), which means the surface processes involving external Cr(VI) adsorption by AJ-N-CQDs. The higher value of α may be due to the greater surface area of the AJ-N-CQDs for the immediate adsorption of Cr(VI) from the aqueous solution. AJ-N-CQDs have fluorescence spectra before and after Cr(VI) adsorption, indicating they are promising for chemical sensor applications.

Preparation of water-dispersed monolayer LDH nanosheets by SMA intercalation to hinder the restacking upon redispersion in water

We present a novel method for preparing water-dispersed monolayer layered double hydroxide (LDH) nanosheets (m-LDH). By intercalating styrene-maleic anhydride copolymer (SMA) into LDH, we obtained m-LDH through a simple aging step that produced stable, translucent colloidal solutions. After drying, the resulting powder can be redispersed in water to recover the m-LDH monolayer structure. To our knowledge, this is the first report of immediate recovery of the m-LDH monolayer structure from dried powder after redispersion in water. Our method may have significant implications for preparing and utilizing m-LDH nanosheets in various applications.

Highly efficient iodine capture and ultrafast fluorescent detection of heavy metals using PANI/LDH@CNT nanocomposite

Here, the hybrid material of polyaniline/layered double hydroxide@carbonnanotubes (PANI/LDH@CNT) is considered a multifunctional material. Instrumental methods, including FTIR, XRD, TEM, SEM, and TGA/DTA were utilized to characterize PANI/LDH@CNT. The polymerization method created PANI/LDH@CNT as an adsorbent to remove toxic iodine in hexane solution with a capture capacity of 303.20 mg g^-1 during 9 h. It is 900 mg g^-1 in the vapor phase within 24 h. After three cycles, the PANI/LDH@CNT could be regenerated while maintaining 91.90 % iodine adsorption efficiency. Due to the presence of free amine (-N) groups, OH^-, CO₂H, and π-π conjugated structures in the PANI/LDH@CNT, it is also explored for efficient iodine uptake. It was demonstrated that the pseudo-first-order (PFO) and Langmuir model had the optimum correlation with the kinetic and isotherm data, respectively. Moreover, the use of PANI/LDH@CNT is not only limited to iodine capture; it can also be utilized as a sensitive sensor that displays a fluorescence "turn-off" response for Mn⁷⁺ and Cr⁶⁺ ions and a fluorescence "turn-on" response in the case of Al³⁺ ions. The fluorescence intensity of the PANI/LDH@CNT was turned off in the presence of Mn⁷⁺ and Cr⁶⁺ because of the fluorescence inner filter effect (IFE) mechanism. In contrast, the fluorescence intensity was turned on in the case of Al³⁺, relying on the chelation-enhanced fluorescence (CHEF) effect mechanism. Under optimal conditions, the limit of detection (LOD) of 51, 59, and 81 nM for Mn⁷⁺, Cr^6+, and Al³⁺, respectively. According to the literature, this is probably the first example based on PANI/LDH@CNT as a multifunctional hybrid material employed as an adsorbent for capturing radioactive iodine and as a chemosensor for detecting heavy metal ions in aqueous solutions.

Molecularly imprinted polymers for per- and polyfluoroalkyl substances enrichment and detection

Per- and polyfluoroalkyl substances (PFAS) are highly toxic pollutants of significant concern as they are being detected in water, air, fish and soil. They are extremely persistent and accumulate in plant and animal tissues. Traditional methods of detection and removal of these substances use specialised instrumentation and require a trained technical resource for operation. Molecularly imprinted polymers (MIPs), polymeric materials with predetermined selectivity for a target molecule, have recently begun to be exploited in technologies for the selective removal and monitoring of PFAS in environmental waters. This review offers a comprehensive overview of recent developments in MIPs, both as adsorbents for PFAS removal and sensors that selectively detect PFAS at environmentally-relevant concentrations. PFAS-MIP adsorbents are classified according to their method of preparation (e.g., bulk or precipitation polymerization, surface imprinting), while PFAS-MIP sensing materials are described and discussed according to the transduction methods used (e.g., electrochemical, optical). This review aims to comprehensively discuss the PFAS-MIP research field. The efficacy and challenges facing the different applications of these materials in environmental water applications are discussed, as well as a perspective on challenges for this field that need to be overcome before exploitation of the technology can be fully realised.

Construction of efficient Ni-FeLDH@MWCNT@Cellulose acetate floatable microbeads for Cr(VI) removal: Performance and mechanism

Water pollution is an aggravating dilemma that is extending around the world, threatening human survival. Strikingly, the notorious heavy metals like hexavalent chromium ions (Cr⁶⁺) cause environmental problems raising awareness of the essentials for finding feasible solutions. For this purpose, the self-floating Ni-FeLDH@MWCNT@CA microbeads were prepared for removing Cr⁶⁺. The morphological, thermal, and composition characteristics of Ni-FeLDH@MWCNT@CA microbeads were analyzed using XRD, FTIR, TGA, SEM, XPS, and zeta potential. Notably, the adsorption aptitude of Cr⁶⁺ was enhanced by raising the MWCNTs proportion to 5 wt% in microbeads. The Cr⁶⁺ adsorption onto Ni-FeLDH@MWCNT@CA fitted Langmuir and Freundlich isotherm models with q_m of 384.62 mg/g at pH 3 and 298 K. The adsorption process was described kinetically by the pseudo-2nd order model. More importantly, the adsorption of Cr⁶⁺ onto Ni-FeLDH@MWCNT@CA occurred via electrostatic interactions, inner/outer sphere complexations, ion exchange, and reduction mechanisms. Besides, the cycling test showed the remarkable reusability of Ni-FeLDH@MWCNT@CA floatable microbeads for five subsequent cycles. The self-floating Ni-FeLDH@MWCNT@CA microbeads in this work provide essential support for the potential applications for the remediation of heavy metals-containing wastewater.

Advances in Sorptive Removal of Hexavalent Chromium (Cr(VI)) in Aqueous Solutions Using Polymeric Materials

Sorptive removal of hexavalent chromium (Cr(VI)) bears the advantages of simple operation and easy construction. Customized polymeric materials are the attracting adsorbents due to their selectivity, chemical and mechanical stabilities. The mostly investigated polymeric materials for removing Cr(VI) were reviewed in this work. Assembling of robust functional groups, reduction of self-aggregation, and enhancement of stability and mechanical strength, were the general strategies to improve the performance of polymeric adsorbents. The maximum adsorption capacities of these polymers toward Cr(VI) fitted by Langmuir isotherm model ranged from 3.2 to 1185 mg/g. Mechanisms of complexation, chelation, reduction, electrostatic attraction, anion exchange, and hydrogen bonding were involved in the Cr(VI) removal. Influence factors on Cr(VI) removal were itemized. Polymeric adsorbents performed much better in the strong acidic pH range (e.g., pH 2.0) and at higher initial Cr(VI) concentrations. The adsorption of Cr(VI) was an endothermic reaction, and higher reaction temperature favored more robust adsorption. Anions inhibited the removal of Cr(VI) through competitive adsorption, while that was barely affected by cations. Factors that affected the regeneration of these adsorbents were summarized. To realize the goal of industrial application and environmental protection, removal of the Cr(VI) accompanied by its detoxication through reduction is highly encouraged. Moreover, development of adsorbents with strong regeneration ability and low cost, which are robust for removing Cr(VI) at trace levels and a wider pH range, should also be an eternally immutable subject in the future. Work done will be helpful for developing more robust polymeric adsorbents and for promoting the treatment of Cr(VI)-containing wastewater.

Carbon Nanotubes Decorated with Coordination Polymers for Fluorescence Detection of Heavy-Metal Ions and Nitroaromatic Chemicals

Herein, [Nd(NO₃)₃(H₂pzdca)] _n (MA-1) was synthesized from a reaction of 2,3-pyrazinedicarboxylic acid [H₂Pzdca] as an organic linker with salt of Nd(III) under solvothermal conditions. The detailed structural analysis for crystals was performed utilizing single-crystal X-ray diffraction (SCXRD). After that, the neodymium-based coordination polymer (MA-1) crystal was directly generated upon the surface of functionalized carbon nanotubes (F-CNTs) through bonds or affinity between F-CNTs and MA-1 via the solvothermal approach. Meanwhile, the existence of F-CNTs does not affect the production of MA-1 crystals. FT-IR, PXRD, SEM, TEM, and SCXRD studies were used to characterize the crystalline material, MA-1 and MA-1@CNT. To investigate the MA-1@CNT sensing properties, Pb(II), As(III), Cr(VI), and nitrobenzene (NB) were utilized as analytes. It is worth mentioning that MA-1@CNT developed as a susceptible sensor exhibits a fluorescence "turn-on" response for Pb(II) and As(III) ions, while a fluorescence "turn-off" response in the case of Cr(VI) and NB with significantly low limit of detection (LOD) values of 15.9 for Pb(II), 16.0 for As(III), 76.9 for Cr(VI), and 21.1 nM for NB, which are comparable with the lowest LOD available in the literature. Furthermore, MA-1@CNT could be conveniently regenerated and reused for at least three cycles by simply filtering and washing with water several times. The sensing mechanism is ascribed to the inner filter effect owing to the overlap between the emission and/or excitation bands of MA-1@CNT with the absorption bands of Cr(VI) and NB. In contrast, the fluorescence enhancement in the case of Pb(II) and As(III) could be correlated to the chelation-enhanced fluorescence phenomenon. These results indicate that MA-1@CNT is an ideal sensor for Pb(II), As(III), Cr(VI), and NB recognition.

Polymer based nanocomposites: A strategic tool for detection of toxic pollutants in environmental matrices

A large fraction of population is suffering from waterborne diseases due to the contaminated drinking water. Both anthropogenic and natural sources are responsible for water contamination. Revolution in industrial and agriculture sectors along with a huge increase in human population has brought more amount of wastes like heavy metals, pesticides and antibiotics. These toxins are very harmful for human health, therefore, it is necessary to sense their presence in environment. Conventional strategies face various problems in detection and quantification of these pollutants such as expensive equipment and requirement of high maintenance with limited portability. Recently, nanostructured devices have been developed to detect environmental pollutants. Polymeric nanocomposites have been found robust, cost effective, highly efficient and accurate for sensing various environmental pollutants and this is due to their porous framework, multi-functionalities, redox properties, great conductivity, catalytic features, facile operation at room temperature and large surface area. Synergistic effects between polymeric matrix and nanomaterials are responsible for improved sensing features and environmental adaptability. This review focuses on the recent advancement in polymeric nanocomposites for sensing heavy metals, pesticides and antibiotics. The advantages, disadvantages, operating conditions and future perspectives of polymeric nanocomposites for sensing toxic pollutants have also been discussed.

Adsorptive removal of heavy metal anions from water by layered double hydroxide: A review

High-valence heavy metals with high ecotoxicity are generally found in water in the form of anions, and this increases heavy metal pollution intensity and treatment difficulty. Recent studies have pointed to the potential efficiency of layered double hydroxides (LDHs) to meet this challenge. In this review, we retrospectively research the development of LDHs using a Java application called CiteSpace. We describe the unique layer structure, highly adjustable chemical properties, and diverse synthesis methods of LDHs, all of which decide the effective adsorption of heavy metal anions by LDHs. Subsequently, we focus on discussing the adsorption mechanism of LDHs on heavy metal anions, as well as the current state of research and future directions for microscopic interaction mechanisms. For practical applications, it is critical to improve the adsorption selectivity and stability. We then recommend solutions to improve the adsorption selectivity and stability after identifying the influencing mechanism. Finally, we provide our perspectives on the future development of LDHs adsorption of heavy metal anions.

Insight into ANN and RSM Models’ Predictive Performance for Mechanistic Aspects of Cr(VI) Uptake by Layered Double Hydroxide Nanocomposites from Water

Mathematical predictive models are vital tools for understanding of pollutant uptake during adsorptive water and wastewater treatment processes. In this study, applications of CoAl-LDH and its bentonite-CoAl intercalated LDH (bentonite-CoAl-LDH) for uptake of Cr(VI) from water were modeled using response surface methodology (RSM) and artificial neural network (ANN), and their performance for predicting equilibrium, thermodynamics and kinetics of the Cr(VI) uptake were assessed and compared based on coefficient of determination (R2) and root mean square error (RMSE). The uptake of Cr(VI) fits well quartic RSM polynomial models and ANN models based on Levenberg–Marquardt algorithms (ANN-LMA). Both models predicted a better fit for the Langmuir model compared to the Freundlich model for the Cr(VI) uptake. The predicted non-linear Langmuir model contestant (KL) values, for both the RSM and ANN-LMA models yielded better ΔG°, ΔH and ΔS predictions which supported the actual feasible, spontaneous and greater order of reaction as well as exothermic nature of Cr(VI) uptake onto the tested adsorbents. Employing the linear Langmuir model KL values dwindles the thermodynamic parameter predictions, especially for the RSM models. The excellent kinetic parameter predictions for the ANN-LMA models further indicate a mainly pseudo-second-order process, thus confirming the predominant chemisorption mechanism as established by the Cr(VI) speciation and surface charges for the Cr(VI) uptake by both CoAl-LDH and bentonite-CoAl-LDH. The ANN-LMA models showed consistent and insignificant decline in their predictions under different mechanistic studies carried out compared to the RSM models. This study demonstrates the high potential reliability of ANN-LMA models in capturing Cr(VI) adsorption data for LDHs nanocomposite heavy metal uptake in water and wastewater treatment.

Fate of Cr(VI) during aging of ferrihydrite-humic acid co-precipitates: Comparative studies of structurally incorporated Al(III) and Mn(II)

Ferrihydrite-humic acid co-precipitates have impacts on the adsorption and reduction of Cr(VI) in the natural environment. Besides, ferrihydrite-humic acid co-precipitates usually coexist with foreign metal cations like Al(III) and Mn(II), which may change the properties of ferrihydrite and affect the fate of Cr(VI). In this work, structurally incorporated Al(III) or Mn(II) in ferrihydrite-humic acid co-precipitates with Cr(VI) (Fh-HA-Cr-Al or Fh-HA-Cr-Mn) were prepared, and the behavior and phase transformation of co-precipitates were explored via the characterization analyses of samples during aging for 10 days. This study showed that partial adsorbed Cr(VI) was reduced to Cr(III) in the presence of humic acid, thereby reducing the toxicity of Cr(VI). Interestingly, two different results occurred because of the incorporation of Al(III) and Mn(II). Al(III) hindered the transformation of ferrihydrite and changed the aging products by inhibiting the dissolution of ferrihydrite, which decreased Cr to incorporate iron minerals. By contrast, doping of Mn(II) accelerated the phase transformation of co-precipitates, and was more conducive to the encapsulation and fixation of Cr. The results of this study can facilitate the understanding of the effects of Al(III) and Mn(II) on Cr(VI) fixation during the aging of Fh-HA-Cr.

Development of Solid Phase Extraction Method Based on Ion Imprinted Polymer for Determination of Cr(III) Ions by ETAAS in Waters

In this work, a new solid phase extraction method for the determination of chromium species in water samples by electrothermal atomic absorption spectrometry was developed. For selective separation of Cr(III) ions under dynamic conditions, two ion imprinted polymers containing Cr(III)-1,10-phenanthroline complex (Cr(III)-phen) were prepared with the use of one (styrene, ST) or two (styrene and 4-vinylpyridine, ST-4VP) functional monomers. The physicochemical properties of those solid sorbents towards Cr(III) ions were studied and compared. It was found that Cr(III) ions were retained on the Cr(III)-phen-ST and Cr(III)-phen-ST-4VP polymers with high efficiency and repeatability (91.6% and 92.9%, RSD < 2%) from solutions at pH 4.5. The quantitative recovery of the analyte (91.7% and 93.9%, RSD < 4%) was obtained with 0.1 mol/L EDTA solution. The introduction of 4VP, an additional functional monomer, improved selectivity of the Cr(III)-phen-ST-4VP polymer towards Cr(III) ions in the presence of Cu(II), Mn(II) and Fe(III) ions, and slightly decreased the sorption capacity and stability of that polymer. The accuracy of procedures based on both polymeric sorbents was proved by analyzing the standard reference material of surface water SRM 1643e. The method using the Cr(III)-phen-ST polymer was applied for determining of Cr(III) ions in tap water and infusion of a green tea.

Nano chromium embedded in f-CNT supported CoBi-LDH nanocomposites for selective adsorption of Pb2+and hazardous organic dyes

Transition metal-doped carbon-coated layered double hydroxides for the removal of lead (II) and hazardous organic dyes have attracted increasing attention for wastewater treatment in recent years. In this work, nanostructured CoBi-LDH/Cr@CNT composites were successfully synthesized by hydrothermal route. The CoBi-LDH/Cr@CNT was characterized by instrumental techniques such as XRD, FTIR, TEM, SEM, XPS and TGA/DTA. Adsorption of Pb²⁺ and organic dyes, i.e.,Rose Bengal (RB) and Congo red (CR) by CoBi-LDH/Cr@CNT was performed by batch experiment.The effect of several parameters including contact time, adsorbent dose, pH, temperature, and concentration was also investigated. Under optimum conditions, the adsorption capacity of CoBi-LDH/Cr@CNT for RB, CR and Pb²⁺ pollutants were (278.4 mg g^-1), (164.6 mg g^-1) and (503.2 mg g^-1) and the removal efficiency achieved is 98.2%, 95.0% and 100% respectively. The selectivity of CoBi-LDH/Cr@CNT nanocomposite towards Pb²⁺ has been studied using ICP-AES.The isothermal results were analyzed using Freundlich and Langmuir models. Adsorption isotherm for Pb²⁺(R² = 0.975), RB (R² = 0.997) and CR (R² = 0.992) agrees with the Langmuir model indicating monolayer adsorption. The sorption kinetics data well fitted pseudo-first-order model for Pb²⁺ (R² = 0.975), RB (R² = 0.996), and CR (R² = 0.995).The results demonstrated that the synthesized CoBi-LDH/Cr@CNT nanocomposite can be used as an effective sorbent for the removal of pollutants from wastewater.

Highly efficient removal of Cr(VI) from aqueous solution by pinecone biochar supported nanoscale zero-valent iron coupling with Shewanella oneidensis MR-1

Nanoscale zero-valent iron (nZVI) has been extensively used to remove various pollutants. However, the rapid deactivation due to aggregation and surface passivation severely limits its practical application. In this study, a novel composite with nZVI supported by pinecone biochar (nZVI-PBC) was successfully synthesized and used for the removal of high concentration Cr(VI) from aqueous solution in the presence of Shewanella oneidensis MR-1 (MR-1). The results showed that the nZVI-PBC coupling with MR-1 (nZVI-PBC/MR-1) exhibited an excellent removal performance for high concentration Cr(VI) compared to the nZVI-PBC alone. Under optimal conditions, 100 mg/L Cr(VI) could be removed completely by nZVI-PBC/MR-1 within 48 h, while only 39.50% of Cr(VI) was removed by nZVI-PBC alone. The improvement of Cr(VI) removal is due to the dissolution of the surface passivation layer of nZVI-PBC, formation of sorbed Fe(II) in the presence of MR-1, and an important role of extracellular polymeric substance (EPS) derived from MR-1. X-ray photoelectron spectroscopy (XPS) and Cr K-edge X-ray absorption near-edge structure spectra (XANES) confirmed that most Cr(VI) was reduced to insoluble Cr(III) and formed Cr₂O₃, Cr_xFe_1-x(OH)₃ and FeCr₂O₄ precipitates, and a small amount of unreduced Cr(VI) was immobilized through adsorption and complexation. The results suggest that nZVI-PBC/MR-1 can effectively overcome the limitations of nZVI and achieve highly efficient removal of high concentration Cr(VI).

Insight into the synergistic adsorption-reduction character of chromium(VI) onto poly(pyrogallol-tetraethylene pentamine) microsphere in synthetic wastewater

Facile fabrication of the ultra-high-performance adsorbent can effectively ameliorate the Cr(VI)-pollution elimination in sewage control. Herein, a simple synthesis strategy is proposed to tap a versatile chelating resin poly(pyrogallol-tetraethylene pentamine) (PPTA) with respect to Cr(VI) removal from solution. Multiple changing factors which affect the adsorption behavior of PPTA are explored sequentially, such as initial pH, adsorbate concentration, adsorbent dosage, temperature, foreign ions, etc. The microstructure and functional mechanism of synthetic adsorbent are investigated systematically by means of various characterizations including TEM, EDS, FT-IR, XPS, etc. Consequently, the as-prepared PPTA-3 microsphere by reactant ratio of 1: 1 represents a brilliant synergistic adsorption and reduction result for Cr(VI) by the drastic electrostatic interaction of -NH₃⁺ and -OH₂⁺ groups, including satisfactory removal efficiency which closes to 100 % in low concentration, favorable specificity for the influence from coexistent ions (Mo(VI), Mn(VII), Cl^-, Cr(III), etc), and passable recyclability. Following the surpassingly fitting with Langmuir isotherm model, its maximum capacity reaches 714.29 mg g^-1 at 30 °C. The removal performance is essentially in agreement with the pseudo-second-order kinetics, simultaneously, suffers the rate-limiting impact depending on intra-particle diffusion process. In brief, this newly developed chelating resin presents an effective means with regard to the Cr(VI)-wastewater treatment or other uses in the future.

Recent Advances in Layered Double Hydroxide-Based Electrochemical and Optical Sensors

Layered double hydroxides (LDHs) have attracted considerable attention as promising materials for electrochemical and optical sensors owing to their excellent catalytic properties, facile synthesis strategies, highly tunable morphology, and versatile hosting ability. LDH-based electrochemical sensors are affordable alternatives to traditional precious-metal-based sensors, as LDHs can be synthesized from abundant inorganic precursors. LDH-modified probes can directly catalyze or host catalytic compounds that facilitate analyte redox reactions, detected as changes in the probe's current, voltage, or resistance. The porous and lamellar structure of LDHs allows rapid analyte diffusion and abundant active sites for enhanced sensor sensitivity. LDHs can be composed of conductive materials such as reduced graphene oxide (rGO) or metal nanoparticles for improved catalytic activity and analyte selectivity. As optical sensors, LDHs provide a spacious, stable structure for synergistic guest-host interactions. LDHs can immobilize fluorophores, chemiluminescence reactants, and other spectroscopically active materials to reduce the aggregation and dissolution of the embedded sensor molecules, yielding enhanced optical responses and increased probe reusability. This review discusses standard LDH synthesis methods and overviews the different electrochemical and optical analysis techniques. Furthermore, the designs and modifications of exemplary LDHs and LDH composite materials are analyzed, focusing on the analytical performance of LDH-based sensors for key biomarkers and pollutants, including glucose, dopamine (DA), H2O2, metal ions, nitrogen-based toxins, and other organic compounds.