P-doped biochar regulates nZVI nanocracks formation for superefficient persulfate activation

Optimized combination of zero-valent iron and oxygen-releasing biochar as cathodes of microbial fuel cells to enhance copper migration in sediment

Membrane-less single-medium sediment microbial fuel cells (single-SMFC) can remove Cu2+ from sediment through electromigration. However, the high mass transfer resistance of the sediment and amount of oxygen at the cathode of the SMFC limit its Cu2+ removal ability. Therefore, this study used an oxygen-releasing bead (ORB) for slow oxygen release to increase oxygen at the SMFC cathode and improve the mass transfer property of the sediment. Resultantly, the copper removal efficiency of SMFC increased significantly. Response surface methodology was used to optimize the nano zero-valent iron (nZVI)-modified biochar as the catalyst to enhance the ability of the modified ORB (ORBm) to remove Cu2+ and slow release of O2. The maximum Cu2+ removal (95 %) and the slowest O2 release rate (0.41 mg O2/d·g ORBm) were obtained when the CaO2 content and ratio of nZVI-modified biochar to unmodified biochar were 0.99 g and 4.95, respectively. When the optimized ORBm was placed at the single-SMFC cathode, the voltage output and copper removal increased by 4.6 and 2.1 times, respectively, compared with the system without ORBm. This shows that the ORBm can improve the migration of Cu2+ in the sediment, providing a promising remediation method for Cu-contaminated sediments.

Persulfate activation with biochar supported nanoscale zero- valent iron: Engineering application for effective degradation of NCB in soil

Nitrochlorobenzene (NCB) is very common in pesticide and chemical industries, which has become a major problem in soil environment. However, the remediation of NCB contaminated soil is received finite concern. Using biochar as a substrate for nanoscale-zero valent iron (nZVI/p-BC) to activate peroxodisulfate (PDS), a novel heterogeneous oxidative system had been applied in the current study to remediate NCB contaminants in soil. The degradation efficiencies and kinetics of m-NCB, p-NCB, and o-NCB by various systems were contrasted in soil slurry. Key factors including the dosage of nZVI/p-BC, the molar ratio of nZVI/PDS, initial pH and temperature on degradation of NCB were further examined. The results confirmed that the nZVI/p-BC/PDS displayed the remarkable performance for removing NCB compared with other systems. Higher temperature with nZVI/PDS molar ratio of 2:1 under the acidic condition favored the reduction of NCB. The treatment for NCB with optimal conditions were evaluated for the engineering application. The mechanism of nZVI/p-BC/PDS indicated that electron transfer between p-BC and nZVI was responsible for activation of PDS, generating active species (SO4•-, •OH and 1O2) via both the free and non-free radical pathways. Experimental results revealed prominent availability of nZVI/p-BC/PDS system in remediation of actual contaminated field by NCB.

Facilely tuning the coating layers of Fe nanoparticles from iron carbide to iron nitride for different performance in Fenton-like reactions

In this study, a series of Fe-based materials are facilely synthesized using MIL-88A and melamine as precursors. Changing the mass ratio of melamine and MIL-88A could tune the coating layers of generated zero-valent iron (Fe0) particles from Fe3C to Fe3N facilely. Compared to Fe/Fe3N@NC sample, Fe/Fe3C@NC exhibits better catalytic activity and stability to degrade carbamazepine (CBZ) with peroxymonosulfate (PMS) as oxidant. Free radical quenching tests, open-circuit potential (OCP) test and electron paramagnetic resonance spectra (EPR) prove that hydroxyl radicals (OH) and superoxide radical (O2-) are dominant reactive oxygen species (ROSs) with Fe/Fe3C@NC sample. For Fe/Fe3N@NC sample, the main ROSs are changed into sulfate radicals (SO4-) and high valent iron-oxo (Fe (IV)=O) species. In addition, the better conductivity of Fe3C is beneficial for the electron transfer from Fe0 to the Fe3C, thus could keep the activity of the surface sites and obtain better stability. DFT calculation reveals the better adsorption and activation ability of Fe3C than Fe3N. Moreover, PMS can also be adsorbed on the Fe sites of Fe3N with shorter FeO bonds and longer SO bonds than on Fe3C, the Fe (IV)=O is thus present in the Fe/Fe3N@NC/PMS system. This study provides a novel strategy for the development of highly active Fe-based materials for Fenton-like reactions and thus could promote their real application.

Enhancing Fenton-like reaction through a multifunctional molybdenum disulfide film coating on nano zero valent iron surface (MoS2@nZVI): Collaboration of radical and non-radical pathways

In this study, we synthesized nano zero-valent iron incorporated with a multifunctional molybdenum disulfide film (MoS2@nZVI). The material exhibited a 100.00 % removal efficiency for sulfamethoxazole (SMX) and achieved a kobs of 0.4485 min-1 within 10 min. The excellent degradation performance can be attributed to the incorporation of the MoS2 film, which facilitated Fe2+ regeneration. Simultaneously, the MoS2 film assisted in proton accumulation and electron transfer, thereby amplifying the efficiency of SMX degradation across a wide pH range. Comprehensive experimental examinations and characterizations confirmed the selectivity and stability of the MoS2@nZVI catalysts, encompassing both degradation efficiency and structural stability. Interestingly, the MoS2@nZVI/PMS system for SMX degradation significantly involved a non-radical mechanism (1O2), along with radicals (SO4·-, ·OH, and O2·-). The direct oxidation of PMS by Fe2+ not only facilitated the generation of ·OH and SO4·- but also actively engaged in a reaction with O2, leading to the production of O2·-. The primary pathway for 1O2 production was established through the interplay between Mo6+ and O2·-, in conjunction with the direct electron transfer (DET) mechanism between PMS and SMX. The contributions of these active species to SMX degradation occurred in the following precedence: SO4·- > 1O2 > ·OH > O2·-. Notably, the primary pathways for radicals and non-radicals were studied during separate reaction periods. This investigation proposed a promising approach for mitigating pharmaceutical pollutants using a transition metal sulfide-modified nZVI catalyst.

The application of P-modified biochar in wastewater remediation: A state-of-the-art review

Phosphorus modified biochar (P-BC) is an effective adsorbent for wastewater remediation, which has attracted widespread attention due to its low cost, vast source, unique surface structure, and abundant functional groups. However, there is currently no comprehensive analysis and review of P-BC in wastewater remediation. In this study, a detailed introduction is given to the synthesis method of P-BC, as well as the effects of pyrolysis temperature and residence time on physical and chemical properties and adsorption performance of the material. Meanwhile, a comprehensive investigation and evaluation were conducted on the different biomass types and phosphorus sources used to synthesize P-BC. This article also systematically compared the adsorption efficiency differences between P-BC and raw biochar, and summarized the adsorption mechanism of P-BC in removing pollutants from wastewater. In addition, the effects of P-BC composite with other materials (element co-doping, polysaccharide stabilizers, microbial loading, etc.) on physical and chemical properties and pollutant adsorption capacity of the materials were investigated. Some emerging applications of P-BC were also introduced, including supercapacitors, CO2 adsorbents, carbon sequestration, soil heavy metal remediation, and soil fertility improvement. Finally, some valuable suggestions and prospects were proposed for the future research direction of P-BC to achieve the goal of multiple utilization.

Synthesis of stabilized zero-valent iron particles and role investigation of humic acid-Fex+ shell in Fenton-like reactions and surface stability control

Herein, a novel humic acid-Fex+ complex-coated ZVI (HA-Fex+@ZVI) was synthesized and used to activate peroxydisulfate (PDS) for phenol degradation. The HA-Fex+ shell selectively reacted with PDS rather than O2, leading to the formation of modified ZVI with excellent surface stability in storage and ultraefficient PDS activation in advanced oxidation processes (AOPs). As a result, the phenol degradation and PDS activation efficiencies of HA-Fex+@ZVI/PDS were ∼14.4 and ∼1.8 times higher than those of ZVI/PDS, respectively. Mechanistic explorations revealed that the replacement of the HA-Fex+ shell relative to the original passivation layer of ZVI greatly changed the SO4•- generation pathway from a heterogeneous process to a homogeneous process, resulting from the slow exposure of Fe0 (generating dissolved Fe2+) and the depolymerized HA (enhancing the Fe3+/Fe2+ cycle). Based on experimental analysis and density functional theory (DFT) calculations, the Fe3+ in HA-Fex+ could be reduced to Fe2+ by PDS, resulting in the disintegration of the HA-Fex+ shell and exposure of Fe0 core active sites. Furthermore, compared to similar catalysts synthesized with commercial HA and traditional chemicals, HA-Fex+@ZVI synthesized with multiple waste biomasses exhibited better performance. This research provides valuable insights for designing ZVI-based catalysts with excellent storage stability and ultraefficient PDS catalytic activity for AOPs.

Research Progress on the Degradation of Organic Pollutants in Water by Activated Persulfate Using Biochar-Loaded Nano Zero-Valent Iron

Biochar (BC) is a new type of carbon material with a high specific surface area, porous structure, and good adsorption capacity, which can effectively adsorb and enrich organic pollutants. Meanwhile, nano zero-valent iron (nZVI) has excellent catalytic activity and can rapidly degrade organic pollutants through reduction and oxidation reactions. The combined utilization of BC and nZVI can not only give full play to their advantages in the adsorption and catalytic degradation of organic pollutants, but also help to reduce the agglomeration of nZVI, thus improving its efficiency in water treatment and providing strong technical support for water resources protection and environmental quality improvement. This article provides a detailed introduction to the preparation method and characterization technology, reaction mechanism, influencing factors, and specific applications of BC and nZVI, and elaborates on the research progress of BC-nZVI in activating persulfate (PS) to degrade organic pollutants in water. It has been proven experimentally that BC-nZVI can effectively remove phenols, dyes, pesticides, and other organic pollutants. Meanwhile, in response to the existing problems in current research, this article proposes future research directions and challenges, and summarizes the application prospects and development trends of BC-nZVI in water treatment. In summary, BC-nZVI-activated PS is an efficient technology for degrading organic pollutants in water, providing an effective solution for protecting water resources and improving environmental quality, and has significant application value.

Degradation of trichloroethylene by biochar supported nano zero-valent iron (BC-nZVI): The role of specific surface area and electrochemical properties

Direct electron transfer and the involvement of atomic hydrogen (H⁎) are considered the main mechanisms for reductive dechlorination promoted by nano zero-valent iron (nZVI) supported on highly conductive carbon. It is still unclear how precisely H⁎, the specific surface area, and the electrochemical characteristics contribute to biochar supported nano zero-valent iron (BC-nZVI) activity in chlorinated hydrocarbon contaminant removal. In this study, a range of BC-nZVIs were prepared by a liquid-phase reduction process, and the contributions of specific surface area and electrochemical performance to H⁎ generation and electron transfer have been assessed. The mechanism of trichloroethylene (TCE) dechlorination by BC-nZVIs has been evaluated in terms of removal efficiency and the ultimate degradation products. The results have demonstrated that BC-nZVIs exhibit a higher specific surface area and TCE degradation efficiency compared with the bare nZVI. Ethane, ethylene, and acetylene were the principal TCE degradation products. The elimination of TCE was not significantly affected by differences in BC-nZVI specific surface area, but electron transfer and sustained generation of H⁎ were dependent on the catalyst electrochemical characteristics. The electrochemical properties of biochar serve to lower the corrosion potential of nZVI, improving electronic transfer capability and reactivity and promoting direct electron transfer for the degradation of TCE. In addition, the enhanced electrochemical properties also facilitate the reaction of nZVI with water and can promote the sustained generation of H⁎. Generation of H⁎ played a key role in reductive dechlorination over BC-nZVIs, which was related to the properties of the biochar support. This study focuses on the role of H⁎ and electrochemical performance in TCE reductive dechlorination, and provides a theoretical foundation and experimental support for the practical application of BC-nZVIs.

Heteroatom-modulated NiCo2O4 apparent energy activation of PMS for tetracycline removal: Mechanism and toxicity analysis

Heteroatom doping to reconfigure the electronic structure of heterogeneous catalysts is expected to lead to the development of advanced oxidation water purification materials with superior performance and greater stability. Herein, a series of catalysts with different elemental doping was developed by a simple and environmentally friendly one-step self-propagating combustion method to remove Tetracycline (TC). After S-doping, the normalized kinetic constant of TC was significantly increased from 30.49 to 159.41 min-1M-1 within 30 min, which is even higher than most recent heterogeneous catalysts. The prepared S-doped NiCo2O4 (NCO-S) exhibits an extremely promising catalytic performance for oxidation (92.8 %) and mineralization (65.9 %) of TC in a wide pH range (3-11). The resistance to interference is excellent for inorganic ions and even in real water samples. Quenching experiments, electron paramagnetic resonance (EPR), and electrochemical analyses demonstrated that the non-radical oxidation pathway, including electron transfer and 1O2, dominated the degradation process after S doping. It is speculated that possible intermediates and toxicological studies are discussed, finding that the overall degradation process is moving towards low toxicity to reveal prospects for large-scale applications. This work not only provides a way to remove TC, but may also inspire the design of more efficient and stable materials for water treatment and other applications.

Multistage utilization of soybean straw-derived P-doped biochar for aquatic pollutant removal and biofuel usage

Biochar is of great importance to realizing solid biowastes reduction and environmental remediation. Modifying biochar for better performance is also of great concern to achieve property improvement. P-doped biochar from soybean straw is prepared for multistage utilization to realize water pollutant removal and biofuel usage. The results suggest that the prepared biochar is adequate for sulfadiazine adsorption and has stable performance under coexisting ions and aquatic pH. Furthermore, the higher heating value of the biochar is close to coal and thus can be an alternative to fossil fuel. The maximum sulfadiazine adsorption amount of P-doped biochar is 252.24 mg·g-1, and the P-doped biochar HHV is 24 MJ·kg-1 which can be an alternative to coal. The greenhouse gas and pollutant emission potential are also considered to explore the environmental impact of P-doped biochar production and usage. Overall, the optimal ratio of soybean straw: K3PO4 is 3:1.

Recent Advances in Nanoscale Zero-Valent Iron (nZVI)-Based Advanced Oxidation Processes (AOPs): Applications, Mechanisms, and Future Prospects

The fast rise of organic pollution has posed severe health risks to human beings and toxic issues to ecosystems. Proper disposal toward these organic contaminants is significant to maintain a green and sustainable development. Among various techniques for environmental remediation, advanced oxidation processes (AOPs) can non-selectively oxidize and mineralize organic contaminants into CO2, H2O, and inorganic salts using free radicals that are generated from the activation of oxidants, such as persulfate, H2O2, O2, peracetic acid, periodate, percarbonate, etc., while the activation of oxidants using catalysts via Fenton-type reactions is crucial for the production of reactive oxygen species (ROS), i.e., •OH, •SO4-, •O2-, •O3CCH3, •O2CCH3, •IO3, •CO3-, and 1O2. Nanoscale zero-valent iron (nZVI), with a core of Fe0 that performs a sustained activation effect in AOPs by gradually releasing ferrous ions, has been demonstrated as a cost-effective, high reactivity, easy recovery, easy recycling, and environmentally friendly heterogeneous catalyst of AOPs. The combination of nZVI and AOPs, providing an appropriate way for the complete degradation of organic pollutants via indiscriminate oxidation of ROS, is emerging as an important technique for environmental remediation and has received considerable attention in the last decade. The following review comprises a short survey of the most recent reports in the applications of nZVI participating AOPs, their mechanisms, and future prospects. It contains six sections, an introduction into the theme, applications of persulfate, hydrogen peroxide, oxygen, and other oxidants-based AOPs catalyzed with nZVI, and conclusions about the reported research with perspectives for future developments. Elucidation of the applications and mechanisms of nZVI-based AOPs with various oxidants may not only pave the way to more affordable AOP protocols, but may also promote exploration and fabrication of more effective and sustainable nZVI materials applicable in practical applications.

Efficient Removal of Antimony(V) from Antimony Mine Wastewater by Micrometer Zero-Valent Iron

This paper investigates the effectiveness of two commercial micron zero-valent irons (mZVIs) in removing Sb(V) from antimony mine wastewater. The wastewater contains a range of complex components and heavy metal ions, including As(V), which can impact the removal efficiency of mZVI. The study aims to provide insights into actual working conditions and focuses on influencing factors and standard conditions. The results demonstrate that mZVI can reduce Sb(V) concentration in the mine wastewater from 3875.7 μg/L to below the drinking water standard of 5 μg/L within 2 h. Adding a small amount of mZVI every 30 min helps to maintain a high removal rate. The study confirms the existence of a reduction reaction by changing the atmospheric conditions of the reaction, and the addition of 1,10-phenanthroline highlights the important role of active Fe(II) in the adsorption and removal of Sb(V) by mZVI. Additionally, the paper presents an innovative experimental method of acid treatment followed by alkali treatment, which proves the interfacial reaction between mZVI and Sb(V). Overall, the study demonstrates that the removal of Sb(V) by mZVI entails a dual function of reduction and adsorption, highlighting the potential of mZVI in repairing Sb(V) in antimony mine wastewater.

Ferrous ion enhanced Fenton-like degradation of emerging contaminants by sulfidated nanosized zero-valent iron with pH insensitivity

In this study, the performance and mechanism of the integrated sulfidated nanosized zero-valent iron and ferrous ions (S-nZVI/Fe2+) system for oxygen activation to remove emerging contaminants (ECs) were comprehensively explored. The S-nZVI/Fe2+ system exhibited a 2.4-8.2 times of increase in the pseudo-first order kinetic rate constant for the oxidative degradation of various ECs compared to the S-nZVI system under aerobic conditions, whereas negligible removal was observed in both nZVI and nZVI/Fe2+ systems. Moreover, remarkable EC mineralization efficiency and benign detoxification capacity were also demonstrated in the S-nZVI/Fe2+ system. We revealed that dosing Fe2+ promoted the corrosion of S-nZVI by maintaining an acidic solution pH, which was conducive to O2 activation by dissolved Fe2+ and surface-absorbed Fe(II) to produce •OH. Furthermore, the generation of H* was enhanced for the further reduction of Fe(III) and H2O2 to Fe(II) and •O2-, resulting in the improvement of consecutive single-electron O2 activation for •OH production. Additionally, bisphenol A (BPA) degradation by S-nZVI/Fe2+ was positively correlated with the S-nZVI dosage, with an optimum S/Fe molar ratio of 0.15. The Fenton-like degradation process by S-nZVI/Fe2+ was pH-insensitive, indicating its robust performance over a wide pH range. This study provides valuable insights for the practical implementation of nZVI-based technology in achieving high-efficiency removal of ECs from water.

Bacteria-based biochar as a persulfate activator to degrade organic pollutants

Carbon-based catalysts for activating persulfate to drive advanced oxidation processes (AOPs) are widely used in wastewater treatment. In this study, Shewanella oneidensis MR-1, a typical ferric reducing electroactive microorganism, was utilized as the raw material of biochar (BC) to prepare a novel green catalyst (MBC). The effect of MBC on activating persulfate (PS) to degrade rhodamine B (RhB) was evaluated. Experimental results showed that MBC could effectively activate PS to degrade RhB to reach 91.70% within 270 min, which was 47.4% higher than that of pure strain MR-1. The increasing dosage of PS and MBC could improve the removal of RhB. Meanwhile, MBC/PS can well perform in a wide pH range, and MBC showed good stability, achieving 72.07% removal of RhB with MBC/PS after 5 cycles. Furthermore, the free radical quenching test and EPR experiments confirmed the presence of both free radical and non-free radical mechanisms in the MBC/PS system, with •OH, SO4•- and 1O2 contributing to the effective degradation of RhB. This study successfully provided a new application for bacteria to be used in the biochar field.