Fine-tuning mesoporous adsorbent for simultaneous ultra-trace palladium(II) detection, separation and recovery

Enhancing irrigation water quality efficiently with potassium feldspar-derived adsorbent: Heavy metal detoxification and nutrient augmentation

The pollution of Pb2+ and Cd2+ in both irrigation water and soil, coupled with the scarcity of vital mineral nutrition, poses a significant hazard to the security and quality of agricultural products. An economical potassium feldspar-derived adsorbent (PFDA) was synthesized using potassium feldspar as the main raw material through ball milling-thermal activation technology to solve this problem. The synthesis process is cost-effective and the resulting adsorbent demonstrates high efficiency in removing Pb2+ and Cd2+ from water. The removal process is endothermic, spontaneous, and stochastic, and follows the quasi-second-order kinetics, intraparticle diffusion, and Langmuir model. The adsorption and elimination of Pb2+ and Cd2+ is largely dependent on monolayer chemical sorption. The maximum removal capacity of PFDA for Pb2+ and Cd2+ at room temperature is 417 and 56.3 mg·g-1, respectively, which is superior to most mineral-based adsorbents. The desorption of Pb2+/Cd2+ on PFDA is highly challenging at pH≥3, whereas PFDA and Pb2+/Cd2+ are recyclable at pH≤0.5. When Pb2+ and Cd2+ coexisted, Pb2+ was preferentially removed by PFDA. In the case of single adsorption, Pb2+ was mainly adsorbed onto PFDA as Pb2SiO4, PbSiO3·xH2O, Pb3SiO5, PbAl2O4, PbAl2SiO6, PbAl2Si2O8, Pb2SO5, and PbSO4, whereas Cd2+ was primarily adsorbed as CdSiO3, Cd2SiO4, and Cd3Al2Si3O12. After the complex adsorption, the main products were PbSiO3·xH2O, PbAl2Si2O8, Pb2SiO4, Pb4Al2Si2O11, Pb5SiO7, PbSO4, CdSiO3, and Cd3Al2Si3O12. The forms of mineral nutrients in single and complex adsorption were different. The main mechanisms by which PFDA removed Pb2+ and Cd2+ were chemical precipitation, complexation, electrostatic attraction, and ion exchange. In irrigation water, the elimination efficiencies of Pb2+ and Cd2+ by PFDA within 10 min were 96.0 % and 70.3 %, respectively, and the concentrations of K+, Si4+, Ca2+, and Mg2+ increased by 14.0 %, 12.4 %, 55.7 %, and 878 %, respectively, within 60 min. PFDA holds great potential to replace costly methods for treating heavy metal pollution and nutrient deficiency in irrigation water, offering a sustainable, cost-effective solution and paving a new way for the comprehensive utilization of potassium feldspar.

Synthesis, antimicrobial activity, antioxidant activity and molecular docking of novel chitosan derivatives containing glycine Schiff bases as potential succinate dehydrogenase inhibitors

Succinate dehydrogenase (SDH) is an important inner mitochondrial membrane-bound enzyme involved in redox reactions during the tricarboxylic acid cycle. Therefore, a series of novel chitosan derivatives were designed and synthesized as potential microbicides targeting SDH and precisely characterized by FTIR, 1H NMR and SEM. Their antifungal and antibacterial activities were evaluated against Botrytis cinerea, Fusarium graminearum, Staphylococcus aureus and Escherichia coli. The bioassays revealed that these chitosan derivatives exerted significant antifungal effects, with four of the compounds achieving 100 % inhibition of Fusarium graminearum merely at a concentration of 0.5 mg/mL. Additionally, CSGDCH showed 79.34 % inhibition of Botrytis cinerea at a concentration of 0.1 mg/mL. In vitro antibacterial tests revealed that CSGDCH and CSGDBH have excellent Staphylococcus aureus and Escherichia coli inhibition with MICs of 0.0156 mg/mL and 0.03125 mg/mL, respectively. Molecular docking studies have been carried out to explore the binding energy and binding mode of chitosan and chitosan derivatives with SDH. The analyses indicated that chitosan derivatives targeted the active site of the SDH protein more precisely, disrupting its normal function and ultimately repressing the growth of microbial cells. Furthermore, the chitosan derivatives were also evaluated biologically for antioxidation, and all of these compounds had a greater degree of reducing power, superoxide radical, hydroxyl radical and DPPH-radical scavenging activity than chitosan. This research has the potential for the development of agricultural antimicrobial agents.

Efficacious adsorption of divalent nickel ions over sodium alginate-g-poly(acrylamide)/hydrolyzed Luffa cylindrica-CoFe2O4 bionanocomposite hydrogel

Existing Ni2+ heavy metal ions in an aqueous medium are highly hazardous for living organisms and humans. Therefore, designing low-cost adsorbents with enhanced effectiveness is essential for removing nickel ions to safeguard public health. In this study, a novel green nanocomposite hydrogel was synthesized through the free radical solution and bulk polymerization method, and its capability to remove divalent nickel ions from aqueous media was examined. The bionanocomposite hydrogel named as SA-g-poly(AAm)/HL-CoFe2O4 was produced by grafting polyacrylamide (AAm) onto sodium alginate (SA) in the presence of a magnetic composite recognized as HL-CoFe2O4, where HL represents hydrolyzed Luffa Cylindrica. By employing FT-IR, XRD, VSM, SEM, EDX-Map, BET, DLS, HPLC, and TGA techniques, morphological evaluation and characterization of the adsorbents were carried out. The performance of the adsorption process was studied under varying operational conditions including pH, temperature, contact duration, initial concentration of pollutant ions, and adsorbent dosage. HPLC analysis proved the non-toxic structure of the bionanocomposite hydrogel. The number of unreacted acrylamide monomers within the hydrogel matrix was measured at 20.82 mg/kg. The optimum conditions was discovered to be pH = 6, room temperature, adsorbent dosage of 1 of g.L-1, initial Ni2+ concentration of 10 mg.L-1, and contact time of 100 min, and the maximum adsorption efficiency at optimal state was calculated as 70.09, 90.25, and 93.83 % for SA-g-poly (AAm), SA-g-poly(AAm)/HL, and SA-g-poly(AAm)/HL-CoFe2O4 samples, respectively. Langmuir isotherm model was in good agreement with the experimental data and the maximum adsorption capacity of SA-g-poly(AAm), SA-g-poly(AAm)/HL, and SA-g-poly(AAm)/HL-CoFe2O4 samples was calculated to be 31.37, 43.15, and 45.19 mg.g-1, respectively. The adsorption process, according to kinetic studies, follows a pseudo-second-order kinetic model. Investigations on thermodynamics also demonstrated that the process is exothermic and spontaneous. Exploring the interference effect of co-existing ions showed that the adsorption efficiency has decreased with concentration enhancement of Ca2+ and Na+ cations in aqueous medium. Furthermore, the adsorption/desorption assessments revealed that after 8 consecutive cycles, there had been no noticeable decline in the adsorption effectiveness. Finally, actual wastewater treatment outcomes demonstrated that the bionanocomposite hydrogel successfully removes heavy metal pollutants from shipbuilding industry effluent. Therefore, the findings revealed that the newly fabricated bionanocomposite hydrogel is an efficient, cost-effective, easy-separable, and green adsorbent that could be potentially utilized to remove divalent nickel ions from wastewater.

Synthesized carboxymethyl-chitosan variant composites for cyclic adsorption-desorption based removal of Fe, Pb, and Cu

The global issue of environmental contamination from industrial wastewater comprising Cu, Fe and Pb demands effective treatment strategies. In this article, a functional composite sorbent was devised to selectively remove copper, iron, and lead from a real-world mimicking wastewater system. For the purpose, high, medium, and low molecular weight chitosan with amine and hydroxyl functional groups were used as a substrate, and glutaraldehyde was used to anchor the organic compound with carboxymethyl groups. Characterization with X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, X-ray analyzer accompanied by field emission scanning electron microscope, and Brunauer-Emmett-Teller were conducted for the synthesized adsorbent. Accordingly, the properties of the adsorbent were evaluated to infer that the synthesis assured a purified and functionalized system. The surface area of the medium carboxymethyl chitosan derivative was analyzed as 31.43 m2 g-1. Various adsorption parameters were examined methodically to assess upon optimal removal requirements. The effect of adsorbent dosage, contact time and concentration on the adsorption of the studied metal ions were conducted and the optimum values were achieved at pH 3.82, 540 min contact duration and 1.2 g L-1 sorbent dose. Maximum adsorbent capacities of 344.83 mg g-1, 9.59 mg g-1, and 90.09 mg g-1 were realized for Cu, Pb, and Fe, respectively. The experimental measurements of the studied heavy metal ions inferred the best fitness of Langmuir isotherm equilibrium and pseudo second order kinetic models. Further, elution studies with easy-to-deploy low-cost acidic and basic eluents (HCl, HNO3, H2SO4, KOH, and NaOH) were conducted with cyclic adsorption-desorption strategies. These investigations confirmed the adsorbent's good reusability up to 3 cycles of adsorption and its proximity to serve as a potential material for multi-heavy metal ions elimination from complex adsorbate systems.

Enhancing the metal ion binding characteristics and reversal of selectivity of crosslinked chitosan sorbents through functionalisation for targeted applications

In this study, we report optimised synthesis of N-carboxymethylated chitosan (CM-Cts) and its crosslinking to obtain, for the first time, glutaraldehyde crosslinked N-carboxymethylated chitosan (CM-Cts-Glu) as a metal ion sorbent. CM-Cts and CM-Cts-Glu were characterised using FTIR and solid state 13C NMR techniques. As compared to epichlorohydrin, glutaraldehyde was found to be better suited for efficient synthesis of the crosslinked functionalised sorbent. CM-Cts-Glu showed better metal ion uptake properties compared to the crosslinked chitosan (Cts-Glu). Metal ion removal by CM-Cts-Glu was studied in detail under different conditions such as different initial solution concentrations, pH, presence of complexants and competing ions. Further, sorption-desorption kinetics was studied and it was shown that complete desorption and multiple cycles of reuse without any loss in capacity was feasible. The maximum Co(II) uptake obtained for CM-Cts-Glu was found to be 265 μmol/g, while for Cts-Glu it was 10 μmol/g. Metal ion sorption by CM-Cts-Glu was found to be through chelation by the carboxylic acid functional groups present over the chitosan backbone. Utility of the CM-Cts-Glu under complexing decontamination formulations used in nuclear industry was ascertained. While Cts-Glu generally preferred iron over cobalt under complexing conditions, it was shown that the selectivity was reversed in favour of Co(II) in the functionalised sorbent, CM-Cts-Glu. N-carboxylation followed by crosslinking with glutaraldehyde was found to be a feasible approach for the generation of superior chitosan-based sorbents.

Combinational exposure to hydroxyatrazine increases neurotoxicity of polystyrene nanoparticles on Caenorhabditis elegans

Using Caenorhabditis elegans as an animal model, we investigated combinational effect between 2-hydroxyatrazine (HA) and polystyrene nanoparticle (PS-NP) on function and development of D-type motor neurons. Exposure to HA (10 and 100 μg/L) alone caused decreases in body bend, head thrash, and forward turn and increase in backward turn. Exposure to 100 μg/L HA also caused neurodegeneration of D-type motor neurons. Moreover, combinational exposure to HA (0.1 and 1 μg/L) induced enhancement in PS-NP (10 μg/L) toxicity in inhibiting body bend, head thrash, and forward turn, and in increasing backward turn. In addition, combinational exposure to HA (1 μg/L) could result in neurodegeneration of D-type motor neurons in PS-NP (10 μg/L) exposed nematodes. Combinational exposure to HA (1 μg/L) and PS-NP (10 μg/L) increased expressions of crt-1, itr-1, mec-4, asp-3, and asp-4, which govern the induction of neurodegeneration. Moreover, combinational exposure to HA (0.1 and 1 μg/L) strengthened PS-NP (10 μg/L)-induced decreases in glb-10, mpk-1, jnk-1, and daf-7 expressions, which encode neuronal signals regulating response to PS-NP. Therefore, our results demonstrated the effect of combinational exposure to HA and nanoplastics at environmentally relevant concentrations in causing toxic effect on nervous system in organisms.

Assessing groundwater recharge rates, water quality changes, and agricultural impacts of large-scale water recycling

The over-exploitation and insufficient replenishment of groundwater (GW) have resulted in a pressing need to conserve freshwater and reuse of treated wastewater. To address this issue, the Government of Karnataka launched a large-scale recycling (440 million liters/day) scheme to indirectly recharge GW using secondary treated municipal wastewater (STW) in drought-prone areas of Kolar district in southern India. This recycling employs soil aquifer treatment (SAT) technology, which involves filling surface run-off tanks with STW that intentionally infiltrate and recharge aquifers. This study quantifies the impact of STW recycling on GW recharge rates, levels, and quality in the crystalline aquifers of peninsular India. The study area is characterized by hard rock aquifers with fractured gneiss, granites, schists, and highly fractured weathered rocks. The agricultural impacts of the improved GW table are also quantified by comparing areas receiving STW to those not receiving it, and changes before and after STW recycling were measured. The AMBHAS_1D model was used to estimate the recharge rates and showed a tenfold increase in daily recharge rates, resulting in a significant increase in the GW levels. The results indicate that the surface water in the rejuvenated tanks meets the country's stringent water discharge standards for STW. The GW levels of the studied boreholes increased by 58-73 %, and the GW quality improved significantly, turning hard water into soft water. Land use land cover studies confirmed an increase in the number of water bodies, trees, and cultivated land. The availability of GW significantly improved agricultural productivity (11-42 %), milk productivity (33 %), and fish productivity (341 %). The study's outcomes are expected to serve as a role model for the rest of Indian metro cities and demonstrate the potential of reusing STW to achieve a circular economy and a water-resilient system.

Melamine-Ag with dual functions of electrochemiluminescence luminophore and coreactant accelerators: Construction of MIP/M-Ag@MoS2-QDs sensing platform for specific detection of thiabendazole

A novel self-enhancement molecularly imprinted electrochemiluminescence (ECL) sensor (MIP/M-Ag@MoS₂-QDs/GCE) was constructed to detect thiabendazole (TBZ) in food. Melamine was used as template to chelate Ag⁺ to prepare composite nanomaterials (M-Ag). M-Ag possesses both ECL properties and coreactant catalytic properties, which can realize the self-enhancement of ECL luminophore. MoS₂-QDs with excellent edge activity and electrochemical reaction catalytic activity were used to accelerate the reaction rate of the microsystem and further enhance the ECL intensity. The specific detection method of TBZ was established by investigating the ECL response mechanism and specific recognition mechanism of MIP/M-Ag@MoS₂-QDs/GCE. The ECL intensity was proportioned to the lg C_(TBZ) in the linear range 5 × 10^-8 mol L^-1-5 × 10^-5 mol L^-1 with a limit detection of 1.42 × 10^-8 mol L^-1. The satisfactory recovery rate (83.57%-101.03%) was obtained in sample analysis, which was in good agreement with the analysis result of HPLC.

Engineering and application of polysaccharides and proteins-based nanobiocatalysts in the recovery of toxic metals, phosphorous, and ammonia from wastewater: A review

Global waste production is anticipated reach to 2.59 billion tons in 2030, thus accentuating issues of environmental pollution and health security. 37 % of waste is landfilled, 33 % is discharged or burned in open areas, and only 13.5 % is recycled, which makes waste management poorly efficient in the context of the circular economy. There is therefore a need for methods to recycle waste into valuable materials through resource recovery process. Progress in the field of recycling is strongly dependent on the development of efficient, stable, and reusable, yet inexpensive catalysts. In this case, a growing attention has been paid to development and application of nanobiocatalysts with promising features. The main purpose of this review paper is to: (i) introduce nanobiomaterials and describe their effective role in the preparation of functional nanobiocatalysts for the recourse recovery aims; (ii) provide production methods and the efficiency improvement of nanobaiocatalysts; (iii) give comprehensive description of valued resource recovery for reducing toxic chemicals from the contaminated environment; (iv) describe various technologies for the valued resource recovery; (v) state the limitation of the valued resource recovery; (vi) and finally economic importance and current scenario of nanobiocatalysts strategies applicable for the resource recovery processes.

Effective Adsorption and Removal of Doxorubicin from Aqueous Solutions Using Mesostructured Silica Nanospheres: Box-Behnken Design Optimization and Adsorption Performance Evaluation

The aim of this study is to evaluate the efficacy of mesoporous silica nanospheres as an adsorbent to remove doxorubicin (DOX) from aqueous solution. The surface and structural properties of mesoporous silica nanospheres were investigated using BET, SEM, XRD, TEM, ζ potential, and point of zero charge analysis. To optimize DOX removal from aqueous solution, a Box-Behnken surface statistical design (BBD) with four times factors, four levels, and response surface modeling (RSM) was used. A high amount of adsorptivity from DOX (804.84 mg/g) was successfully done under the following conditions: mesoporous silica nanospheres dose = 0.02 g/25 mL; pH = 6; shaking speed = 200 rpm; and adsorption time = 100 min. The study of isotherms demonstrated how well the Langmuir equation and the experimental data matched. According to thermodynamic characteristics, the adsorption of DOX on mesoporous silica nanospheres was endothermic and spontaneous. The increase in solution temperature also aided in the removal of DOX. The kinetic study showed that the model suited the pseudo-second-order. The suggested adsorption method could recycle mesoporous silica nanospheres five times, with a modest reduction in its ability for adsorption. The most important feature of our adsorbent is that it can be recycled five times without losing its efficiency.

Investigations of microwave absorption performance of bi-layer absorber composed of FeWO4 & BiVO4 nanocomposite powder in 2-18 GHz

Optimization necessitates every feature to be scrutinized associated with enhancement for microwave absorption. So, interplay between simulation and experiment is a significant aspect to find optimal findings in this regard. Herein, microwave absorption characteristics of as-prepared FeWO₄ and BiVO₄ nanomaterials were investigated by preparing mono layer and bilayer samples. For the bilayer samples, simulation technique was used to regulate microwave absorption efficiency. Using simulation technique, bilayer sample has achieved a minimum reflection loss (RL_min) of -42 dB with BiVO₄ as a top layer (0.6 mm thickness) and FeWO₄ as a bottom layer (0.8 mm thickness) with effective absorption Bandwidth (EAB) of 13 GHz (15-2 GHz) at 8.2 GHz frequency. The results show that the layered architecture of the absorbent is substantially responsible for its remarkable microwave absorption efficiency. Simulated results of the bilayer sample were also verified with experimental findings. This work provides a facile synthesis route, novel insights into the design of bilayer absorbent as well as simulation and experimental support for high-performance microwave bilayer absorber.

Immunochromatographic Assay based on Sc-TCPP 3D MOF for the rapid detection of imidacloprid in food samples

In this work, a highly sensitive immunochromatographic test strip (ITS) based on Scandium-Tetrakis (4-carboxyphenyl) porphyrin (TCPP) metal-organic framework nanocubes (ScTMNs) was developed for ultrasensitive and facile visual determination of imidacloprid (IDP). TCPP as the porphyrin-based planar ligand and Sc³⁺ as the metal center were applied to form the ScTMNs via coordination chelation. Giving the credit to its excellent optical characteristics, strong affinity with monoclonal antibodies, and favorable biocompatibility, the ScTMNs was selected as a signal tag. Under optimized conditions, the ITS exhibited a great liner relationship in the range of 0.04-3 ng/mL and the detection limit was 0.04 ng/mL for the IDP detection. Additionally, IDP was successfully detected in tomatoes, millet, corn and carrot samples with satisfied recoveries. To the best of our knowledge, this is the first time that ScTMNs have been used in immunochromatography which are expected to have potential applications in detection of other substances.

Selective extraction of precious metals in the polar aprotic solvent system: Experiment and simulation

The traditional hydrometallurgical process is the mainstream technology to recover precious metals from e-waste, which usually adopts strong acid/base and strong oxide with high environmental cost and energy consumption. In the present study, the selective extraction of precious metals was simulated and experimented with DMF as the solvent and Cl^- ions provided by CaCl₂ and CuCl₂ (oxidizing agent). The leaching and precipitation rates of precious metals (Au, Ag, Pd) can reach more than 98% under optimization conditions. Kinetic data shows that the control model of the leaching process on precious metals was determined by linear fitting of the shrinkage model. The complex trace precious metals were extracted selectively using dimethylglyoxime and deionized water as precipitators by the leaching-precipitation-cycle method. Meanwhile, the waste liquid produced by this reaction process could be cyclically utilized. Furthermore, the leaching mechanism of precious metals was proposed. DMF could be complexed with the metals as well as coordination ions (Cl^-), which can reduce the redox potentials. Cu(II) could be easily reduced to Cu(I) in the DMF system due to the higher second ionization energy of copper, which is not influenced by the hydration effect, thus shifting the equilibrium to the metal leach side. Oppositely, the addition of water promoted the conversion of Cu(I) to Cu(II) since the higher hydration energy of Cu(II) compensates for the second ionization energy. This research opens up a new path of sustainable development and provides basic theory and practical experience for environmentally friendly recovery of precious metals from e-waste.

Green synthesis of Ag2O nanoparticles using Punica granatum leaf extract for sulfamethoxazole antibiotic adsorption: characterization, experimental study, modeling, and DFT calculation

Silver oxide (Ag₂O) nanoparticles (NPs) were generated by synthesizing green leaf extract of Punica granatum, and afterwards they were used as adsorbent to remove the antibiotic additive sulfamethoxazole (SMX) from aqueous solutions. Prior of their use as adsorbent, the Ag₂O NPs were characterized by various methods such as X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), scanning electron microscopy/energy-dispersive X-ray (SEM-EDX), and transmission electron microscopy (TEM). The Ag₂O NPs were found to be spherically shaped and stabilized by the constituents of the extract. Further, at SMX antibiotic concentration of 100 mg L^-1, the Ag₂O NPs achieved almost complete removal of 98.93% within 90 min, and by using 0.8 g L^-1 of adsorbent dose at pH=4 and temperature T=308 K. In addition, the experimental data were well fitted with the theoretical Langmuir model indicating homogeneous adsorbed layer of the SMX antibiotic on the Ag₂O NPs surface. The maximum uptake capacity was 277.85 mg g^-1. A good agreement was also found between the kinetic adsorption data and the theoretical pseudo-second-order model. Regarding the thermodynamic adsorption aspects, the data revealed an endothermic nature and confirmed the feasibility and the spontaneity of the adsorption reaction. Furthermore, the regeneration study has shown that the Ag₂O NPs could be efficiently reused for up to five cycles. The geometric structures have been optimized and quantum chemical parameters were calculated for the SMX unprotonated (SMX^+/-) and protonated (SMX⁺) using density functional theory (DFT) calculation. The DFT results indicated that the unprotonated SMX^+/- reacts more favorably on the Ag₂O surface, as compared to the protonated SMX⁺. The SMX binding mechanism was predominantly controlled by the electrostatic attraction, hydrogen bond, hydrophobic, and π-π interactions. The overall data suggest that the Ag₂O NPs have promising potential for antibiotic removal from wastewater.

Bioremediation and decontamination potentials of metallic nanoparticles loaded nanohybrid matrices - A review

The current nanotechnological advancements provide an astonishing insight to fabricate nanomaterials for nano-bioremediation purposes. Exciting characteristics possessed by hybrid matrices at the nanoscale knock endless opportunities to nano-remediate environmentally-related pollunanomaterials tants of emerging concern. Nanometals are considered among the oldest generation of the world has ever noticed. These tiny nanometals and nanometal oxides showed enormous potential in almost every extent of industrial and biotechnological domains, including their potential multipurpose approach to deal with water impurities. In this manuscript, we discussed their role in the diversity of water treatment technologies used to remove bacteria, viruses, heavy metals, pesticides, and organic impurities, providing an ample perspective on their recent advances in terms of their characteristics, attachment strategies, performance, and their scale-up challenges. Finally, we tried to explore their futuristic contribution to nano-remediate environmentally-related pollutants of emerging concern aiming to collect treated yet safe water that can be reused for multipurpose.

Phosphate determination in environmental, biological and industrial samples using a smartphone as a capture device

A lab-made device was built to analyse phosphate in four different matrices using a smartphone as a capturing device.

Hollow spheres of iron oxide as an “enzyme-mimic”: preparation, characterization and application as biosensors

Nanostructured hollow spheres of iron oxide are demonstrated as “nanozymes” for the dual mode (spectrophotometric and electrochemical) detection of hydrogen peroxide & cholesterol biomarkers and a novel electrochemical sensing mechanism is proposed.

A facile chemiluminescence strategy for copper(ii) ion detection utilizing azothiacalix[4]arene-functionalized carboxymethylcellulose polymeric ligand

The design and characterization of azothiacalix[4]arene-functionalized carboxymethylcellulose, used for the detection of nanomolar levels of Cu2+via a chemiluminescence method.

Probe tethered monolithic architectures as facile solid-state chemosensors for the on-site colorimetric recognition of Co(II) in aqueous and industrial samples

In this work, we report two novel solid-state opto-chemosensors that proffer exclusive selectivity and excellent sensitivity for the naked-eye detection of ultra-trace Co²⁺ ions. The opto-chemosensors are concocted using structurally engineered porous silica and polymer monolith templates that are uniformly arranged with a chromoionophoric probe i.e., (Z)-2-mercapto-5-(quinolin-8-yldiazenyl)pyrimidine-4,6-diol (AQTBA). The probe anchored monolithic opto-chemosensors induces sequential color transitions, from yellowish-orange to dark brown, with incremental addition of Co²⁺ ions. The optimized ground state structure of the AQTBA probe and its AQTBA-Co²⁺ complex are analyzed using a gaussian 16 program at B3LYP level, with a 6-311+ G (d, p) basis set. The structural and surface morphology of the opto-sensors are characterized using various microscopic, spectroscopic, and diffraction techniques, which discloses a uniform pattern of pore network that proffers rapid ion diffusion kinetics to the probe chelating sites. The proposed monolithic sensors exhibit a high degree of tolerance towards various foreign cations and anions, thus revealing its exclusive selectivity in targeting ultra-trace concentrations of Co²⁺. The silica and polymer monolithic sensors exhibit a broad linear response range of 0-200 ppb, with a detection limit of 0.35 and 0.07 ppb for Co²⁺ ions, respectively. The unique features of the proposed sensors are their faster response kinetics (120 s), greater reusability (nine cycles), excellent chemical and thermal durability (pH ≤ 12.0; T ≤ 200 °C), with reliable data reproducibility (recovery ≥99.3 %; RSD ≤2.3 %). The proposed solid-state opto-chemosensors paves way for maximum waste reduction strategy, along with the feasibility for real-time monitoring of environmental and industrial water samples.

Functionalized layered double hydroxides composite bio-adsorbent for efficient copper(II) ion encapsulation from wastewater

In this study, naturally abundant and inexpensive bamboo was used to make cheaper activated charcoal for efficient encapsulation of toxic copper (Cu(II)) ion from wastewater. The functionalized bamboo charcoal-Layered double hydroxides (BC-LDHs) composite bio-adsorbent was prepared using co-precipitation method. The composite bio-adsorbent was exploited to eliminate Cu(II) ion with high sensitivity and selectivity from contaminated water. The adsorption parameters including the effect of pH, contact time, adsorbent dose, and effect of initial concentration were optimized in systematic way and the adsorption kinetics and isotherms were investigated for potential use in real sample treatment. The physicochemical properties and morphological structure of the adsorbent were examined using X-ray Diffraction, Scanning Electronic Microscopy, Fourier Transform Infrared Spectroscopy and Thermogravimetric Analysis to understand the Cu(II) ion adsorption mechanism. The adsorption results revealed that the BC-LDH could remove almost 100% of Cu(II) ion from aqueous solution at pH range between 3.0 and 6.0 within 30 min. The maximum monolayer adsorption capacity was determined to be 85.47 mg/g based on the Langmuir isotherm. The adsorption equilibrium data were well-fitted by the Langmuir isotherm model (R² = 0.998) and the experimental kinetic data were supported by the pseudo-second order model (R² = 0.999). The BC-LDH could be reused without losing its adsorption performance in several cycles after successful regeneration with 0.10 M HCl. The Cu(II) ion removal mechanism was postulated with intercalated ion exchange, surface precipitation and interaction between BC-LDH and surface functionalities. Therefore, the highly functional BC-LDH composite could be a promising adsorbent for efficient Cu(II) ion removal from wastewater.

Novel micro-structured carbon-based adsorbents for notorious arsenic removal from wastewater

The contamination of groundwater by arsenic (As) in Bangladesh is the biggest impairing of a population, with a large number of peoples affected. Specifically, groundwater of Gangetic Delta is alarmingly contaminated with arsenic. Similar, perilous circumstances exist in many other countries and consequently, there is a dire need to develop cost-effective decentralized filtration unit utilizing low-cost adsorbents for eliminating arsenic from water. Morphological synthesis of carbon with unique spherical, nanorod, and massive nanostructures were achieved by solvothermal method. Owing to their intrinsic adsorption properties and different nanostructures, these nanostructures were employed as adsorption of arsenic in aqueous solution, with the purpose to better understanding the morphological effect in adsorption. It clearly demonstrated that carbon with nanorods morphology exhibited an excellent adsorption activity of arsenite (about 82%) at pH 3, remarkably superior to the two with solid sphere and massive microstructures, because of its larger specific surface area, enhanced acid strength and improved adsorption capacity. Furthermore, we discovered that iron hydroxide radicals and energy-induced contact point formation in nanorods are the responsible for the high adsorption of As in aqueous solution. Thus, our work provides insides into the microstructure-dependent capability of different carbon for As adsorption applications.

Fast one-step preparation of porous carbon with hierarchical oxygen-enriched structure from waste lignin for chloramphenicol removal

This work explored the use of porous carbon (PC) materials converted from waste lignin as raw materials for the removal of chloramphenicol (CAP) in water. The PC with controllable pores was prepared through a facile, cost-effective one-step method. The physical and chemical properties of the material were characterized by BET, SEM, FT-IR, and XRD, and the best conditions for preparation were selected based on the results of adsorption experiments. The PC, which was prepared at reaction temperature of 800 °C and the K₂CO₃/sodium lignosulfonate mass ratio of 4, namely PC-800-4, had a high specific surface area (1305.5 m² g^-1) and pore volume (0.758 cm³ g^-1). At a lower initial concentration of CAP (C₀ = 120 mg L^-1), the maximum adsorption capacity of this adsorbent was 534.0 mg g^-1 at 303 K. In addition, PC-800-4 maintained good adsorption performance in a wide pH range and strongly resisted the interference of ions and humic acid. The results showed that the adsorption removal CAP was based on physical adsorption and chemical adsorption as a process supplement. The advantages of wide sources, high efficiency and speed, wide application, and rich oxygen-containing functional groups made the adsorbent have great application potential for removal chloramphenicol from water.

A multivariate modeling and experimental realization of photocatalytic system of engineered S-C3N4/ZnO hybrid for ciprofloxacin removal: Influencing factors and degradation pathways

Ciprofloxacin, a pharmaceutically active compound, is present as a micropollutant in wastewater, which cannot be removed by conventional techniques due to its recalcitrant nature. Therefore, in the present study, the photocatalytic degradation of this bio-toxic compound was demonstrated using a three-dimensional sulfur-doped graphitic-carbon nitride/zinc oxide hybrid, with enriched oxygen vacancies. The influence of various water matrices and experimental conditions on the ciprofloxacin degradation was optimized. The hybrid material showed 98.8% and 75.8% degradation efficiency under optimum experimental conditions (i.e., catalyst dose: 1 g/L; pH: 5; initial ciprofloxacin concentration: 20 mg/L; temperature: 27 °C) under ultraviolet (UV) and visible light, respectively. A neural-network-based multivariate approach was used to predict a significant model considering the experimental conditions that showed adequate statistical significance (R²: 0.992 and F-value: 8707.1). The relative significance of the experimental conditions was assessed, suggesting that the initial ciprofloxacin concentration has a more significant effect on the degradation efficiency than the other factors. The rate kinetics and reaction mechanisms for ciprofloxacin degradation were demonstrated, and the driving radicals involved were identified. A higher rate of reaction was found under UV irradiation (0.01702 min^-1) than under visible light (0.00802 min^-1). Superoxide radicals were identified as the main driving radicals, which caused substantial photocatalytic reactions among the hybrid and ciprofloxacin molecules. Microscopic and macroscopic analyses of the used hybrid were conducted, which confirmed the presence of higher defect concentrations, crystallinity, and interlinked stacked structure in the hybrid. Hence, the 3D hybrid can be efficiently used and reused for ciprofloxacin degradation. This advanced photocatalytic system can be widely used to remediate emerging contaminants in wastewater treatment.

Assessing of cesium removal from wastewater using functionalized wood cellulosic adsorbent

Sustainable materials are urgently desired for treatment of radioactive cesium (Cs) contaminated water to safe-guard the public health. Apart from the synthetic ligand-based materials, the Mangrove charcoal modified adsorbent was fabricated for assessing of Cs removal from waste sample. The raw charcoal was oxidized using nitrification approach and diverse oxygen containing carboxyl, carbonyl and hydroxyl functional groups were introduced. After modification, the adsorbent characteristics were drastically changed as compared to the charcoal during the measurement of FTIR, N₂ adsorption-desorption isotherms and SEM micrographs. The data clarified that charcoal modified adsorbent was exhibited high Cs transport through the inner surface of the adsorbent based on bonding ability. The adsorbent was shown comparatively slow kinetics to Cs ion; however, the adsorption capacity was high as 133.54 mg/g, which was higher than the crown ether based conjugate materials. The adsorption data were followed to the Langmuir adsorption isotherms and the monolayer coverage was possible due to the data presentation. The presence of high amount of Na and K were slightly interfered to the Cs adsorption by the charcoal modified adsorbent, however; the Na and K concentration was 350-600 folds higher than the Cs concentration. Then the proposed adsorbent was selective to Cs for the potential real radioactive Cs contaminated water. The volume reduction was established rather than desorption and reuses advantages. More than 99% volume reduction was measured by burning of Cs adsorbed adsorbent at 500 °C for ensuring the safe storage and disposal of used adsorbent. Therefore, the charcoal modified adsorbent may open the new door to treat the Cs containing wastewater.