1
|
Javaid MA, Cheema SA, Nasir N, Ahmad S, Hussain MT, Tanveer Z, Mustafa MZU, Tahir U, Ali S. Exploring the synergistic effect of carboxymethyl cellulose and chitosan in enhancing thermal stability of polyurethanes through statistical mixture design approach. Int J Biol Macromol 2024; 267:131441. [PMID: 38583848 DOI: 10.1016/j.ijbiomac.2024.131441] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/15/2023] [Revised: 03/20/2024] [Accepted: 04/04/2024] [Indexed: 04/09/2024]
Abstract
The thermal stability of polyurethanes, known for its limitations, was addressed in this research by seeking improvement through the introduction of carbohydrate-based chain extenders. In this research paper, we systematically sought to improve the thermal resistance of polyurethanes by incorporating carboxymethyl cellulose and chitosan, representing a pioneering application of the mixture design approach in their preparation. In this synthesis, hydroxyl-terminated polybutadiene and isophorone diisocyanate (IPDI) were reacted to prepare -NCO terminated prepolymer, which was subsequently reacted with varying mole ratios of CMC and CSN to develop a series of five PU samples. The prepared PU samples were characterized using the Fourier-transformed infrared spectroscopic technique. Thermal pyrolysis of PU samples was examined using thermal gravimetric analysis (TGA). It was observed that, among all the samples, PUS-3 showed remarkable thermal stability over a wide temperature range. A comprehensive statistical analysis was conducted to substantiate the experimental findings. It was estimated that CMC and CSN significantly enhance the thermal stability of the samples when involved in an interaction fashion. The ANOVA Table for the mixture design demonstrates that over 90 % of the total variation in thermal stability is explained by the mixture model across a wide temperature range. Moreover, PSU-3 exhibited 4 % more thermal stability over a wide range of temperatures on average, as compared to contemporary samples.
Collapse
Affiliation(s)
- Muhammad Asif Javaid
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Salman Arif Cheema
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Nadeem Nasir
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Saliha Ahmad
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Muhammad Tahir Hussain
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan.
| | - Zaighum Tanveer
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Muhammad Zia Ul Mustafa
- Department of Chemical Engineering, Universiti Teknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia
| | - Usama Tahir
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| | - Shehbaz Ali
- Department of Applied Sciences, National Textile University, Faisalabad 37610, Pakistan
| |
Collapse
|
2
|
Karamikamkar S, Yalcintas EP, Haghniaz R, de Barros NR, Mecwan M, Nasiri R, Davoodi E, Nasrollahi F, Erdem A, Kang H, Lee J, Zhu Y, Ahadian S, Jucaud V, Maleki H, Dokmeci MR, Kim H, Khademhosseini A. Aerogel-Based Biomaterials for Biomedical Applications: From Fabrication Methods to Disease-Targeting Applications. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2023; 10:e2204681. [PMID: 37217831 PMCID: PMC10427407 DOI: 10.1002/advs.202204681] [Citation(s) in RCA: 6] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/03/2023] [Indexed: 05/24/2023]
Abstract
Aerogel-based biomaterials are increasingly being considered for biomedical applications due to their unique properties such as high porosity, hierarchical porous network, and large specific pore surface area. Depending on the pore size of the aerogel, biological effects such as cell adhesion, fluid absorption, oxygen permeability, and metabolite exchange can be altered. Based on the diverse potential of aerogels in biomedical applications, this paper provides a comprehensive review of fabrication processes including sol-gel, aging, drying, and self-assembly along with the materials that can be used to form aerogels. In addition to the technology utilizing aerogel itself, it also provides insight into the applicability of aerogel based on additive manufacturing technology. To this end, how microfluidic-based technologies and 3D printing can be combined with aerogel-based materials for biomedical applications is discussed. Furthermore, previously reported examples of aerogels for regenerative medicine and biomedical applications are thoroughly reviewed. A wide range of applications with aerogels including wound healing, drug delivery, tissue engineering, and diagnostics are demonstrated. Finally, the prospects for aerogel-based biomedical applications are presented. The understanding of the fabrication, modification, and applicability of aerogels through this study is expected to shed light on the biomedical utilization of aerogels.
Collapse
Affiliation(s)
| | | | - Reihaneh Haghniaz
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | | | - Marvin Mecwan
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | - Rohollah Nasiri
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | - Elham Davoodi
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
- Department of Mechanical and Mechatronics EngineeringUniversity of WaterlooWaterlooONN2L 3G1Canada
| | - Fatemeh Nasrollahi
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
- Department of BioengineeringUniversity of California‐Los Angeles (UCLA)Los AngelesCA90095USA
| | - Ahmet Erdem
- Department of Biomedical EngineeringKocaeli UniversityUmuttepe CampusKocaeli41001Turkey
| | - Heemin Kang
- Department of Materials Science and EngineeringKorea UniversitySeoul02841Republic of Korea
| | - Junmin Lee
- Department of Materials Science and EngineeringPohang University of Science and Technology (POSTECH)Pohang37673Republic of Korea
| | - Yangzhi Zhu
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | - Samad Ahadian
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | - Vadim Jucaud
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| | - Hajar Maleki
- Institute of Inorganic ChemistryDepartment of ChemistryUniversity of CologneGreinstraße 650939CologneGermany
- Center for Molecular Medicine CologneCMMC Research CenterRobert‐Koch‐Str. 2150931CologneGermany
| | | | - Han‐Jun Kim
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
- College of PharmacyKorea UniversitySejong30019Republic of Korea
| | - Ali Khademhosseini
- Terasaki Institute for Biomedical Innovation (TIBI)Los AngelesCA90024USA
| |
Collapse
|
3
|
Chen XY, Nagamine S, Ohshima M, Rodrigue D. High‐performance thermal insulator based on polymer foam and silica xerogel. POLYM ENG SCI 2022. [DOI: 10.1002/pen.25871] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/07/2022]
Affiliation(s)
- Xiao Yuan Chen
- Department of Chemical Engineering Kyoto University Kyoto Japan
- Department of Chemical Engineering Université Laval Quebec City Quebec Canada
| | | | | | - Denis Rodrigue
- Department of Chemical Engineering Université Laval Quebec City Quebec Canada
| |
Collapse
|
4
|
Xu J, Zhang B, Lu Y, Wang L, Tao W, Teng X, Ning W, Zhang Z. Adsorption desulfurization performance of PdO/SiO 2@graphene oxide hybrid aerogel: Influence of graphene oxide. JOURNAL OF HAZARDOUS MATERIALS 2022; 421:126680. [PMID: 34332481 DOI: 10.1016/j.jhazmat.2021.126680] [Citation(s) in RCA: 5] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/25/2021] [Revised: 06/30/2021] [Accepted: 07/16/2021] [Indexed: 05/26/2023]
Abstract
Preparation of PdO/SiO2@graphene oxide (GO) hybrid aerogels were carried out sol-gel method combined with atmospheric drying technology to study their adsorption performance for thiophenics and compared with PdO/SiO2. Scanning electron microscope (SEM), N2 adsorption-desorption isotherms, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and fourier transformation infrared spectroscopy (FT-IR) for samples were performed. The adsorption performance of PdO/SiO2@GO for thiophene were better than that of PdO/SiO2, attributed to that incorporation of GO increased the specific surface area and the Pd incorporation rate, where Pd2+ ions acted as the π-complexation and sulfur-metal (SM) bond adsorption active centers, as well as GO adsorbed thiophene by the π-π stacking effect. The adsorption capacities of PdO/SiO2@GO-1.0 for thiophene (TH), benzothiophene (BT) and dibenzothiophene (DBT) were 8.89, 9.3 and 12.6 mg-S/gads, respectively. The addition of GO in aerogels could improve the inhibition effect of toluene, cyclohexene and pyridine while decreased the inhibition effect of MTBE and H2O for the adsorption of thiophene, due to the π-π stacking effect and the hydrophobicity of GO, respectively. The adsorption process was spontaneous and exothermic, be well fitted by the apparent second-order kinetic model and dominated by chemical interaction. Pd/SiO2@GO-1.0 had a good solvent elution regeneration performance.
Collapse
Affiliation(s)
- Jiacheng Xu
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Bo Zhang
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China.
| | - Yongkang Lu
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Leigang Wang
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Wanyi Tao
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Xiao Teng
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Wensheng Ning
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| | - Zekai Zhang
- Laboratory of Industrial Catalysis, College of Chemical Engineering, Zhejiang University of Technology, 18 Chaowang Road, Hangzhou 310014, China
| |
Collapse
|
5
|
Zhang Y, Wu L, Deng X, Deng Y, Wu X, Shi L, Li M, Liu Q, Cheng X, Li Z. Improving the flame retardance of hydrophobic silica aerogels through a facile post-doping of magnesium hydroxide. ADV POWDER TECHNOL 2021. [DOI: 10.1016/j.apt.2021.03.041] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/28/2022]
|
6
|
Guzel Kaya G, Deveci H. Synergistic effects of silica aerogels/xerogels on properties of polymer composites: A review. J IND ENG CHEM 2020. [DOI: 10.1016/j.jiec.2020.05.019] [Citation(s) in RCA: 26] [Impact Index Per Article: 6.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/31/2022]
|
7
|
Ardekani R, Borhani S, Rezaei B. Selective molecularly imprinted polymer nanofiber sorbent for the extraction of bisphenol A in a water sample. POLYM INT 2020. [DOI: 10.1002/pi.6013] [Citation(s) in RCA: 10] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/18/2022]
Affiliation(s)
- Razieh Ardekani
- Department of Textile EngineeringIsfahan University of Technology Isfahan Iran
| | - Sedigheh Borhani
- Department of Textile EngineeringIsfahan University of Technology Isfahan Iran
| | - Behzad Rezaei
- Department of ChemistryIsfahan University of Technology Isfahan Iran
| |
Collapse
|
8
|
Advances in precursor system for silica-based aerogel production toward improved mechanical properties, customized morphology, and multifunctionality: A review. Adv Colloid Interface Sci 2020; 276:102101. [PMID: 31978639 DOI: 10.1016/j.cis.2020.102101] [Citation(s) in RCA: 39] [Impact Index Per Article: 9.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/06/2019] [Revised: 12/08/2019] [Accepted: 01/06/2020] [Indexed: 11/23/2022]
Abstract
Conventional silica-based aerogels are among the most promising materials considering their special properties, such as extremely low thermal conductivity (~15 mW/mK) and low-density (∼0.003-0.5 g.cm-3) as well as high surface area (500-1200 m2. g-1). However, they have relatively low mechanical properties and entail extensive and energy-consuming processing steps. Silica-based aerogels are mostly fragile and possess minimal mechanical properties as well as a long processing procedure which hinders their application range. The key point in improving the mechanical properties of such a material is to increase the connectivity in the aerogel backbone. Several methods of mechanical improvement of silica-based aerogels have been explored by researchers such as (i) use of flexible silica precursors in silica gel backbone, (ii) surface-crosslinking of silica particles with a polymer, (iii) prolonged aging step in different solutions, (iv) distribution of flexible nanofillers into the silica solution prior to gelation, and, most recently, (v) polymerizing the silica precursor prior to gelation. The polymerized silica precursor, as in the most recent approach, can be gelled either by binodal decomposition (nucleation and growth), resulting in a particulate structure, or by spinodal decomposition, resulting in a non-particulate structure. By optimizing the material composition and processing conditions of materials, the aerogel can be tailored with different functional capabilities. This review paper presents a literature survey of precursor modification toward increased connectivity in the backbone, and the synthesis of inorganic and hybrid systems containing siloxane in the backbone of the silica-based aerogels and its composite version with carbon nanofillers. This review also explains the novel properties and applications of these material systems in a wide area. The relationship among the materials-processing-structure-properties in these kinds of aerogels is the most important factor in the development of aerogel products with given morphologies (particulate, fiber-like, or non-particulate) and their resultant properties. This approach to advancing precursor systems leads to the next-generation, multifunctional silica-based aerogel materials.
Collapse
|
9
|
Li L, Cao B, Sun Y, Yi W, Ni X, Xiao Q. Effect of Filler Treatment on the Release Properties of Coating on Urea Granules. POLYM-PLAST TECH MAT 2019. [DOI: 10.1080/03602559.2018.1466164] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/28/2022]
Affiliation(s)
- Lixia Li
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| | - Bing Cao
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| | - Yumeng Sun
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| | - Wenping Yi
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| | - Xiaohui Ni
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| | - Qiang Xiao
- Institute of Plant Nutrition and Resources, Beijing Academy of Agriculture and Forestry Sciences, Beijing, China
- Research Center of Beijing Municipal Slow and Controlled Release Fertilizers Engineering Technology, Beijing, China
| |
Collapse
|
10
|
Javaid MA, Rizwan M, Khera RA, Zia KM, Saito K, Zuber M, Iqbal J, Langer P. Thermal degradation behavior and X-ray diffraction studies of chitosan based polyurethane bio-nanocomposites using different diisocyanates. Int J Biol Macromol 2018; 117:762-772. [DOI: 10.1016/j.ijbiomac.2018.05.209] [Citation(s) in RCA: 25] [Impact Index Per Article: 4.2] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/17/2018] [Revised: 05/16/2018] [Accepted: 05/28/2018] [Indexed: 10/16/2022]
|
11
|
Sung G, Kim JW, Kim JH. Fabrication of polyurethane composite foams with magnesium hydroxide filler for improved sound absorption. J IND ENG CHEM 2016. [DOI: 10.1016/j.jiec.2016.08.014] [Citation(s) in RCA: 60] [Impact Index Per Article: 7.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/21/2022]
|
12
|
Dourbash A, Buratti C, Belloni E, Motahari S. Preparation and characterization of polyurethane/silica aerogel nanocomposite materials. J Appl Polym Sci 2016. [DOI: 10.1002/app.44521] [Citation(s) in RCA: 21] [Impact Index Per Article: 2.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
Affiliation(s)
- Alireza Dourbash
- School of Chemical Engineering, College of Engineering; University of Tehran; Tehran Iran
- Research Institute of Petroleum Industry; Tehran Iran
| | - Cinzia Buratti
- Department of Engineering; University of Perugia; Perugia Italy
| | - Elisa Belloni
- Department of Engineering; University of Perugia; Perugia Italy
| | - Siamak Motahari
- School of Chemical Engineering, College of Engineering; University of Tehran; Tehran Iran
| |
Collapse
|