Synthesis, characterization, and kinetic study of activated carbon modified by polysulfide rubber coating for aqueous hexavalent chromium removal

A novel zwitterionic magnetic nanocomposite developed for non-invasive speciation analysis of inorganic chromium

3-(2-Aminoethylamino)propyltriethoxysilane and carboxyethylsilanetriol sodium salt were grafted on silica-coated Fe3O4 nanoparticles via sol-gel process to prepare novel amine- and carboxyl-bifunctionalized magnetic nanocomposites (SMNPs-(NH2 + COOH)). After well characterized, this doubly functionalized material was used as magnetic solid-phase extraction (MSPE) adsorbent to separate and enrich inorganic chromium species followed by inductively coupled plasma-mass spectrometry detection. The optimization of MSPE operation parameters including pH was conducted. It is reasonably elucidated that the adsorption mechanisms of zwitterionic SMNPs-(NH2 + COOH) towards chromium species are electrostatic and/or coordination interactions. Cr(VI) and Cr(III) can be adsorbed around pH 3.0 and around 10.0 respectively with strong anti-interference ability not only from other co-existing ions but also from the two labile species each other, and eluted by dilute nitric acid solution. With a 15-fold enrichment factor, the limits of detection of Cr(VI) and Cr(III) were 0.008 and 0.009 μg L-1, respectively, profiting from the maximum adsorption capacities of 7.52 and 6.11 mg g-1. The just one magnetic extraction matrix based speciation scheme possesses excellent convenience and friendliness to Cr(VI) and Cr(III) without any oxidation or reduction prior to capture of these two species. This protocol has been successfully applied to the speciation analysis of inorganic chromium in real-world environmental water samples.

Effective chromium removal of metal anchored alginate-chitosan binary bio-composites

Water is the most essential resource for the biotic and abiotic components of an ecosystem. Any change in the quality of this water may cause adverse impact on the ecosystem. Hexavalent chromium is one such important pollutant that gets exposed in the water mainly through anthropogenic processes. Adsorption is considered to be an effective, economic and easiest method for remediation of such pollutants. Amongst the innumerable adsorbents available, biopolymers fetch the interest due to its cost effectiveness, efficiency and biocompatibility. But, the mechanical strength and workability of such biopolymers makes it unfit to use as an adsorbent. To improve these drawbacks, synthesis of biopolymeric composites become the need of the hour. So, an attempt was made here to synthesize metal cross-linked binary bio-composites using Alginate and Chitosan polymer matrix. Synthesized bio-composites were characterised with the aid of FTIR, XPS, Thermal analysis, SEM with EDAX and subjected for hexavalent chromium removal from water. Analysis of variance (ANOVA) with 95 % confidence intervals was used to assess the significance of independent variables and their interactions. Adsorption studies were done using batch process and to achieve greater sorption, various influencing parameters were optimized one by one. While investigating one parameter, other parameters were kept unaltered. Optimization was done for the parameters like contact time, dosage of the adsorbent, pH of the medium and presence of co-ions. Contact time and dosage for all the composites was 30 mins and 0.1 g respectively. Amongst the composites, Zirconium loaded binary composite possess high sorption capacity of around 14.8 mg/g. While Calcium and Iron loaded composites exhibit sorption capacity of around 9.8 mg/g and 10.4 mg/g respectively. Presence of other co-ions in the medium doesn't affect the sorption process. Isothermal studies infer the adsorption follows Langmuir model and thermodynamic parameters concludes the endothermic and randomness of the adsorption. The bio-composites can be recycled and used upto three cycles. Field trial was conducted and the composites work well in such conditions.

Fabrication of Polyamide6/Polyaniline as an Effective Nano-web Membrane for Removal of Cr (VI) from Water and a Black Box Approach in Modeling of Adsorption Process

Chromium (Cr), as a highly toxic heavy metal ion, is still a severe environmental issue, although many research efforts have been put into its removal from water. Polyaniline (PANI), as a conductive polymer, demonstrated great capability in heavy metal adsorption due to its low cost, ease of synthesis, reversible redox behavior, and chemical stability. However, using PANI powder alone in heavy metal removal causes secondary pollution and aggregation in water. The PANI coating on a substrate could tackle this problem. In this study, polyaniline-coated polyamide6 (PA6/PANI) nano-web membrane was used for the removal of Cr(VI) in both adsorption and filtration-adsorption modes. The PA6/PANI nano-web membrane was fabricated via PA6 electrospinning followed by in-situ polymerization of the aniline monomer. The electrospinning condition of PA6 was optimized by the Taguchi method. The PA6/PANI nano-web membrane was characterized by FESEM, N2-adsorption/desorption, FT-IR, contact angle measurement, and tensile test. FT-IR and FESEM results demonstrated the successful synthesis of PA6/PANI nano-web and PANI homogeneous coating on PA6 nanofibers, respectively. The N2 adsorption/desorption results indicated that the pore volume of the PA6/PANI nano-web decreased by 39% compared to PA6 nanofibers. The tensile test and water contact angle studies showed that the coating of PANI on PA6 nanofibers improves the mechanical properties and hydrophilicity of PA6 by 10% and 25%, respectively. The application of PA6/PANI nano-web in the removal of Cr(VI) in batch and filtration modes exhibits excellent removal of 98.4 and 86.7%, respectively. A pseudo first order model well described the adsorption kinetics, and the adsorption isotherm was best fitted by the Langmuir model. A black box modeling approach based on artificial neural networks (ANN) was developed to predict the removal efficiency of the membrane. The superior performance of PA6/PANI in both adsorption and filtration-adsorption systems makes it a potential candidate for the removal of heavy metals from water on an industrial scale.

Stability of mesoporous silica using ricinoleic methyl ester as a template with the addition of HCl and application of Cd2+ adsorption optimized by Box-Behnken design

Mesoporous silica is restricted to organic solvents or other acidic media. The application of mesoporous silica depends on the medium's chemical stability and mechanical properties. It is necessary to stabilize the mesoporous silica material under acidic conditions. The results of the nitrogen adsorption characterization show that MS-50 has a large surface area and porosity, resulting in good mesoporous silica. Using variance analysis (ANOVA) to compare the collected data, the best conditions were found at a pH of 6.32, a Cd²⁺ concentration of 25.30 ppm, an adsorbent dose of 0.06 g, and a time of 70.44 min. The Cd²⁺ adsorption experiment data best fit the Langmuir isotherm model with the maximum amount of Cd²⁺ that MS-50 could absorb being 103.10 mg g^-1.

Advances in Sorptive Removal of Hexavalent Chromium (Cr(VI)) in Aqueous Solutions Using Polymeric Materials

Sorptive removal of hexavalent chromium (Cr(VI)) bears the advantages of simple operation and easy construction. Customized polymeric materials are the attracting adsorbents due to their selectivity, chemical and mechanical stabilities. The mostly investigated polymeric materials for removing Cr(VI) were reviewed in this work. Assembling of robust functional groups, reduction of self-aggregation, and enhancement of stability and mechanical strength, were the general strategies to improve the performance of polymeric adsorbents. The maximum adsorption capacities of these polymers toward Cr(VI) fitted by Langmuir isotherm model ranged from 3.2 to 1185 mg/g. Mechanisms of complexation, chelation, reduction, electrostatic attraction, anion exchange, and hydrogen bonding were involved in the Cr(VI) removal. Influence factors on Cr(VI) removal were itemized. Polymeric adsorbents performed much better in the strong acidic pH range (e.g., pH 2.0) and at higher initial Cr(VI) concentrations. The adsorption of Cr(VI) was an endothermic reaction, and higher reaction temperature favored more robust adsorption. Anions inhibited the removal of Cr(VI) through competitive adsorption, while that was barely affected by cations. Factors that affected the regeneration of these adsorbents were summarized. To realize the goal of industrial application and environmental protection, removal of the Cr(VI) accompanied by its detoxication through reduction is highly encouraged. Moreover, development of adsorbents with strong regeneration ability and low cost, which are robust for removing Cr(VI) at trace levels and a wider pH range, should also be an eternally immutable subject in the future. Work done will be helpful for developing more robust polymeric adsorbents and for promoting the treatment of Cr(VI)-containing wastewater.

Selective Removal of Hexavalent Chromium by Novel Nitrogen and Sulfur Containing Cellulose Composite: Role of Counter Anions

Exploiting an adsorbent with superb selectivity is of utmost importance for the remediation of Cr (VI)-laden wastewater. In this work, a novel nitrogen and sulfur functionalized 3D macroporous cellulose material (MPS) was prepared by homogeneous cross-link cellulose and polyvinylimidazole, followed by ion exchange with MoS₄^2-. MPS exhibited high removal efficiency at a broad pH range (1.0-8.0) and large adsorption capacity (379.78 mg/g) toward Cr (VI). Particularly, outstanding selectivity with an enormous partition coefficient (1.01 × 10⁷ mL/g) was achieved on MPS. Replacing MoS₄^2- with Cl^- and MoO₄^2- led to a sharp decline in adsorption selectivity, demonstrating that MoS₄^2- contributed substantially to the selectivity. Results of FTIR, XPS, and apparent kinetic analysis revealed that Cr (VI) was first pre-enriched on the MPS surface via electrostatic and dispersion forces, and then reacted with MoS₄^2- to generate Cr (III), which deposited on MPS by forming Cr(OH)₃ and chromium(III) sulfide. This study provides a new idea for designing adsorbents with a superior selectivity for removing Cr (VI) from sewage.

Biochar Nanocomposite as an Inexpensive and Highly Efficient Carbonaceous Adsorbent for Hexavalent Chromium Removal

Biochar is commonly used for soil amendment, due to its excellent water-holding capacity. The Cr(VI) contamination of water is a current environmental issue in industrial regions. Here, we evaluated the effects of two-step modifications on boosting biochar's performance in terms of the removal of aqueous hexavalent chromium (Cr(VI)), along with investigating the alterations to its surface properties. The first modification step was heat treatment under air at 300 °C, producing hydrophilic biochar (HBC). The resulting HBC was then impregnated with zero-valent iron nanoparticles (nZVI), creating an HBC/nZVI composite, adding a chemical reduction capability to the physical sorption mechanism. Unmodified biochar (BC), HBC, and HBC/nZVI were characterized for their physicochemical properties, including surface morphology and elemental composition, by SEM/EDS, while functional groups were ascertained by FTIR and surface charge by zeta potential. Cr(VI) removal kinetic studies revealed the four-time greater sorption capacity of HBC than BC. Although unmodified BC showed faster initial Cr(VI) uptake, it rapidly worsened and started desorption. After nZVI impregnation, the Cr(VI) removal rate of HBC increased by a factor of 10. FTIR analysis of biochars after Cr(VI) adsorption showed the presence of Cr(III) oxide only on the used HBC/nZVI and demonstrated that the carbonyl and carboxyl groups were the main groups involved in Cr(VI) sorption. Modified biochars could be considered an economical substitute for conventional methods.

Preparation and Characterization of an Electrospun Whey Protein/Polycaprolactone Nanofiber Membrane for Chromium Removal from Water

Chromium pollution represents a worldwide concern due to its high toxicity and bioaccumulation in organisms and ecosystems. An interesting material to remove metal ions from water is a whey-protein-based material elaborated by electrospinning, which is an emerging method to produce adsorbent membranes with diverse applications. The aim of this study was to prepare an adsorbent membrane of whey protein isolate (WPI) and polycaprolactone (PCL) by electrospinning to remove chromium ions from water. The adsorbent membrane was synthesized by a central composed design denaturing WPI using 2-Mercaptoethanol and mixing it with PCL to produce electrospun nanofibers. The adsorbent membrane was characterized by denaturation, Scanning Electron Microscope, Fourier-Transform Infrared Spectroscopy, Contact Angle, Thermogravimetric Analysis, and X-ray Photoelectron Spectrometry. The adsorption properties of this membrane were assessed in the removal of chromium. The removal performance of the membrane was enhanced by an increase in temperature showing an endothermic adsorption process. The adsorption process of chromium ions onto the nanofiber membrane followed the Sips adsorption isotherm, while the adsorption kinetics followed a pseudo-second kinetics where the maximum adsorption capacity was 31.0 mg/g at 30 °C and pH 2. This work provides a novel method to fabricate a hybrid membrane with amyloid-type fibrils of WPI and PCL, which is a promising adsorbent to remove heavy metal ions from water.

Highly surface activated carbon to remove Cr(VI) from aqueous solution with adsorbent recycling

To enhance the inferior removal capability of aqueous Cr(VI) by commercial activated carbon under neutral conditions. The emerging ball milling technology was employed and the removal efficiency of Cr(VI) by ball-milled highly activated carbon (HAC) increased from 68.3% to 99.0% under pH 6 and from 42.7% to 77.8% under pH 7 compared to pristine activated carbon (AC), respectively. Raman spectra and Boehm's titration results signified that the enhanced Cr(VI) removal performance of HAC under neutral conditions was associated with the enriched surface acid functional groups, in which the content of COOH groups increased from 0.31 mmol/g to 0.97 mmol/g. Two Cr(VI) removal mechanisms were proposed established on the acid and alkalic solution washed chromium-loaded HAC, involving the reduction of Cr(VI) to Cr(III) subsequently accompany with the formation of chromium hydroxides on the surface and inside the pores of HAC, and the bonding of CrO₄^2- on the surface COOH groups, as confirmed by SEM-EDX element mapping and specific surface area and porosity measurements. The Pseudo-second order model and Freundlich model fitted the adsorption kinetic and isotherm of AC and HAC well severally, suggesting that the specific interaction of Cr(VI) with the HAC surface and the Cr(VI) removal was multi-layer adsorption. Thermodynamic study exhibited the spontaneity of Cr(VI) removal on ball-milled HAC was increased. Reusability and regeneration studies of HAC denoted the potential application on Cr(VI) uptake under neutral conditions.

Biotreatment for the spent lithium-ion battery in a three-module integrated microbial-fuel-cell recycling system

A bio-electrochemically (BE) recycling platform was assembled to recover Li and Co from the cathodic materials of spent LIBs in one integrated system. The BE platform consists of three microbial-fuel-cell (MFC) subsystems, including MFC-A, MFC-B, and MFC-C. Co and Li were smoothly recovered from the cathodic materials in the assembled platform. The initial pH and the loading ratios of LiCoO₂ both significantly influenced the leaching efficiencies of Li and Co in MFC-A. Approximately 45% Li and 93% Co were simultaneously released through the reduction of LiCoO₂ at the initial pH of 1 and the loading ratios of LiCoO₂ of 0.2 g/L. The (NH₄)₂C₂O₄-modified granular activated carbons (GAC) with a thickness of 1.5 cm was favorably stacked adjacent to the cathode of the MFC-B system. About 98% of removal efficiency (RE_Co1) and 96% of recovery efficiency (RE_Co2) of Co were achieved in MFC-B under optimum conditions. The dosing concentration of Li⁺ lower than 2 mg/L and the (NH₄)₂CO₃ of 0.01-0.02 M were conducive to enhancing the recovery of Li from raffinate and guaranteed the higher power output and coulombic efficiencies in MFC-C. The continuous release of CO₂ caused by exoelectrogenic microorganisms on the biofilm facilitated the precipitation of Li₂CO₃.

Removal of sulfadiazine from aqueous solution by in-situ activated biochar derived from cotton shell

Phosphoric acid is used to in-situ activate biochar pyrolyzed by cotton shells to enhance the adsorption ability of sulfadiazine (SDZ). To confirm the optimum condition, different impregnation ratios and impregnation times were investigated. It was found that the biochar (BC) pyrolyzed under the condition of an impregnation ratio of 2.5 and an impregnation time of 6 h showed the highest performance for the removal of SDZ. The maximum adsorption ability was 86.89 mg/g at a temperature of 298 K. The pseudo-second-order model was used to disclose the adsorption process of SDZ by BCs. The experimental data were described by the Langmuir and Temkin isotherms at different temperatures. It was found that the sorption of SDZ was an exothermic process according to the thermomechanical analysis. The activated BC could be recycled for at least five times with a high removal rate of SDZ. Thus, activated BCs are regarded as promising adsorbents for SDZ removal.

Sorption Studies of Chromate by Iron Oxide from Drinking Water

Chromium is well-thought-out heavy metal which is one of the enormously lethal due to its cancer-causing nature. In this study, iron oxide is used as adsorbent for chromate removal from aqueous solution as a function of pH, time, temperature, concentration of adsorbate and media dosage. The influence of pH on Cr (VI) sorption by iron oxide reveals that adsorption is significantly increased as pH is decreased from 8 to 2. The sorption rate is detected to be higher in the beginning and then it remains constant after 120 min of equilibrium time. The removal of Cr (VI) is found to be greater at higher temperature, which confirms the endothermic nature of Cr (VI) adsorption by iron oxide. Whereas, the kinetic investigations confirm that the chromate adsorption follows the pseudo second order with kinetic energy in the range of 8.4–83.7 kJ mol−1.

Recent advances in hexavalent chromium removal from aqueous solutions by adsorptive methods

Chromium exists mainly in two forms in environmental matrices, namely, the hexavalent (Cr(vi)) and trivalent (Cr(iii)) chromium. While Cr(iii) is a micronutrient, Cr(vi) is a known carcinogen, and that warrants removal from environmental samples. Amongst the removal techniques reported in the literature, adsorption methods are viewed as superior to other methods because they use less chemicals; consequently, they are less toxic and easy to handle. Mitigation of chromium using adsorption methods has been achieved by exploiting the physical, chemical, and biological properties of Cr(vi) due to its dissolution tendencies in aqueous solutions. Many adsorbents, including synthetic polymers, activated carbons, biomass, graphene oxide, and nanoparticles as well as bioremediation, have been successfully applied in Cr(vi) remediation. Initially, adsorbents were used singly in their natural form, but recent literature shows that more composite materials are generated and applied. This review focused on the recent advances, insights, and project future directions for these adsorbents as well as compare and contrast the performances achieved by the mentioned adsorbents and their variants.

Facile modification of activated carbon with highly dispersed nano-sized α-Fe2O3 for enhanced removal of hexavalent chromium from aqueous solutions

Activated carbon-coated α-Fe₂O₃ nanoparticles (nFe₂O₃@AC) were synthesized by a facile impregnation method to enhance hexavalent chromium (Cr(VI)) removal from water. The SEM images confirmed that α-Fe₂O₃ particles ranging from 90 to 500 nm were dispersedly loaded on the AC, which successfully amended Cr(VI) removal. The nFe₂O₃@AC was able to remove Cr(VI) with a 3 times higher efficiency of 94% in comparison with the AC. After adsorption, Cr(VI) reduction coupled with AC oxidation and low soluble (Cr_xFe_1-x)(OH)₃ precipitates were eventually formed. The Cr(VI) removal process was pH-dependent and could be well fitted to pseudo second-order kinetics. The nFe₂O₃@AC could be easily regenerated by 0.1 M HCl and showed a good stability as an 80% Cr(VI) removal efficiency was recorded after 4 desorption-adsorption cycles. In addition, this composite had a promising potential for repeated utilization because the AC of the adsorbed nFe₂O₃@AC could be refreshed and remodified with nFe₂O₃ after stripping all the nFe₂O₃ and (Cr_xFe_1-x)(OH)₃ precipitates from its surface by 1 M HCl and a Cr(VI) removal efficiency of 86% could be achieved. Our results demonstrated that the use of nFe₂O₃ is an efficient and promising method to modify AC and enhance Cr(VI) removal form aqueous solutions.