Preparation of polyaminated Fe3O4@chitosan core-shell magnetic nanoparticles for efficient adsorption of phosphate in aqueous solutions

Polyethyleneimine-functionalized magnetic sugarcane bagasse cellulose film for the efficient adsorption of ibuprofen

Polyethyleneimine-modified magnetic sugarcane bagasse cellulose film (P-SBC/Fe3O4 film) was simply fabricated for the removal of ibuprofen (IBP), a typical emerging organic contaminant. The P-SBC/Fe3O4 film exhibited an equilibrium adsorption amount of 370.52 mg/g for IBP and a corresponding removal efficiency of 92.63 % under following adsorption conditions: 318 K, pH 4, and 0.25 mg/mL dosage. Thermodynamic studies indicated that adsorption of IBP on the P-SBC/Fe3O4 film was spontaneous (∆G < 0) and endothermic (∆H > 0). The adsorption data conformed to the Freundlich isotherm model and multilayer adsorption model (two layers), and an average of 3-4 active sites on the P-SBC/Fe3O4 film share an IBP molecule. Both the EDR-IDR and AOAS models vividly described the dynamic characteristics of adsorption process. Model fitting results, theoretical calculations, and comprehensive characterization revealed that adsorption is driven by electrostatic interactions between the primary amine of P-SBC/Fe3O4 film and the carboxyl group of IBP molecule, while other weak interactions are also non-ignorable. Furthermore, quantitative calculations based on density functional theory (DFT) underscored the importance of PEI functionalization. In conclusion, P-SBC/Fe3O4 film is an environmentally friendly and cost-effective adsorbent with significant potential for effectively removing IBP, while maintaining its efficacy over multiple cycles.

Efficient adsorption of phosphorus by macroscopic MOF/chitosan composites and preliminary investigation of subsequent phosphorus recovery through electrochemically-driven struvite precipitation

The proper management of phosphorus (P) from wastewater is crucial for sustainable development consideration. Herein, we developed a strategy which combines adsorption via tailored adsorbents and electrochemically-driven struvite precipitation (ESP) for P recovery. Novel polydopamine-modified Ce-MOF/chitosan composite beads (PDA@Ce-MOF-CS) were prepared by a facile in situ growth of Ce-MOF crystals incorporated natural polymers and PDA coating. The physicochemical properties of PDA@Ce-MOF-CS were characterized. Both batch and fixed-bed column experiments were conducted to evaluate its adsorption performances. Representatively, PDA@Ce-MOF-CS performed good selectivity for P removal and exhibited a maximum adsorption capacity of 161.13 mg P/g at pH 3 and 318 K. Meanwhile, the developed adsorbent showed great reusability after ten regeneration cycles as well as good adsorption stability. The dominant mechanism for efficient P adsorption included electrostatic attraction, surface precipitation and ligand exchange. Interestingly, PDA@Ce-MOF-CS exhibited a remarkable adsorption capacity of 92.86 mg P/g by treating real P-rich electroplating wastewater, and the desorbed P in the eluate could be effectively recovered and converted into a solid fertilizer as struvite via ESP. Overall, this work provided a new research direction for P recovery from wastewater as struvite by combined technologies with the help of macroscopic MOF architectures.

Effective retention of cesium ions from aqueous environment using morphologically modified kaolinite nanostructures: experimental and theoretical studies

Kaolinite can undergo a controlled morphological modification process into exfoliated nanosilicate sheets (EXK) and silicate nanotubes (KNTs). The modified structures were assessed as potential effective adsorbents for the retention of Cs+ ions. The impact of the modification process on the retention properties was assessed based on conventional and advanced equilibrium studies, considering the related steric and energetic functions. The synthetic KNTs exhibit a retention capacity of 249.7 mg g-1 as compared to EXK (199.8 mg g-1), which is significantly higher than raw kaolinite (73.8 mg g-1). The kinetic modeling demonstrates the high effectiveness of the pseudo-first-order kinetic model (R2 > 0.9) to illustrate the sequestration reactions of Cs+ ions by K, EXK, and KNTs. The enhancement effect of the modification processes can be illustrated based on the statistical investigations. The presence of active and vacant receptors enhanced greatly from 19.4 mg g-1 for KA to 40.8 mg g-1 for EXK and 46.9 mg g-1 for KNTs at 298 K. This validates the significant impact of the modification procedures on the specific surface area, reaction interface, and reacting chemical groups' exposure. This also appeared in the enhancement of the reactivity of their surfaces to be able to uptake 10 Cs+ ions by KNTs and 5 ions by EXK as compared to 4 ions by kaolinite. The thermodynamic and energetic parameters (Gaussian energy < 8.6 kJ mol-1; uptake energy < 40 kJ mol-1) show that the physical processes are dominant, which have spontaneous and exothermic properties. The synthetic EXK and KNT structures validate the high elimination performance of the retention of Cs+ either in the existence of additional anions or cations.

A review on chitosan/metal oxide nanocomposites for applications in environmental remediation

A cleaner and safer environment is one of the most important requirements in the future. It has become increasingly urgent and important to fabricate novel environmentally-friendly materials to remove various hazardous pollutants. Compared with traditional materials, chitosan is a more environmentally friendly material due to its abundance, biocompatibility, biodegradability, film-forming ability and hydrophilicity. As an abundant of -NH2 and -OH groups on chitosan molecular chain could chelate with all kinds of metal ions efficiently, chitosan-based materials hold great potential as a versatile supporting matrix for metal oxide nanomaterials (MONMs) (TiO2, ZnO, SnO2, Fe3O4, etc.). Recently, many chitosan/metal oxide nanomaterials (CS/MONMs) have been reported as adsorbents, photocatalysts, heterogeneous Fenton-like agents, and sensors for potential and practical applications in environmental remediation and monitoring. This review analyzed and summarized the recent advances in CS/MONMs composites, which will provide plentiful and meaningful information on the preparation and application of CS/MONMs composites for wastewater treatment and help researchers to better understand the potential of CS/MONMs composites for environmental remediation and monitoring. In addition, the challenges of CS/MONM have been proposed.

Recent advances in removal of inorganic anions from water by chitosan-based composites: A comprehensive review

Chitosan is a modified natural carbohydrate polymer that has been found in the exoskeletons of crustaceans (e.g., lobsters, shrimps, krill, barnacles, crayfish, etc.), mollusks (octopus, oysters, squids, snails), algae (diatoms, brown algae, green algae), insects (silkworms, beetles, scorpions), and the cell walls of fungi (such as Ascomycetes, Basidiomycetes, and Phycomycetes; for example, Aspergillus niger and Penicillium notatum). However, it is mostly acquired from marine crustaceans such as shrimp shells. Chitosan-based composites often present superior chemical, physical, and mechanical properties compared to single chitosan by incorporating the benefits of both counterparts in the nanocomposites. The tunable surface chemistry, abundant surface-active sites, facilitation synthesize and functionalization, good recyclability, and economic viability make the chitosan-based materials potential adsorbents for effective and fast removal of a broad range of inorganic anions. This article reviews the different types of inorganic anions and their effects on the environment and human health. The development of the chitosan-based composites synthesis, the various parameters like initial concentration, pH, adsorbent dosage, temperature, the mechanism of adsorption, and regeneration of adsorbents are discussed in detail. Finally, the prospects and technical challenges are emphasized to improve the performance of chitosan-based composites in actual applications on a pilot or industrial scale.

Magnetic chitosan oligomer-sulfonate-stearic acid triple combination as cisplatin carrier for site-specific targeted on MCF-7 cancer cells: Preparation, characterization and in vitro experiments

In this study, a new amphiphilic target-specific adsorbent, chitosan oligomer-sulfonate-stearic acid triple combination (S-Cho-SA), and magnetic chitosan oligomer-sulfonate-stearic acid triple combination (M-S-Cho-SA) by oleic acid (OA)-modified Fe3 O4 via hydrophobic interaction are fabricated. By modifying the nanoparticle surfaces and having the ability to magnetically allow the target region, these particles attract attention as important particles used in targeting mechanisms in cancer therapy. With magnetic nanoparticles and an external magnetic field, it is possible to transport therapeutic agents to the target site and keep them in the desired effect zone for a longer period of time. These new adsorbents are characterized by scanning electron microscopy (SEM), attenuated total reflection Fourier transform infrared (ATR FT-IR) spectroscopy, nuclear magnetic resonance (NMR), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and thermogravimetric analysis (TG/DTA). After chemical characterization, it is complexed with cisplatin (CDDP). The magnetic adsorbents were loaded with high efficiency (>50%), and the release experiments exhibited that cisplatin is released more at pH 4.5 compared with pH 7.4 at 37°C. It showed better drug release results under a magnetic field for magnetic adsorbents (36% for pH 4.5 and 3.6% for pH 7.4). The biocompatibility of the prepared adsorbents was demonstrated via the XTT assay in MCF-7 cell lines. The results also exhibited that S-Cho-SA and M-S-Cho-SA were biocompatible, and free cisplatin and cisplatin-complexed adsorbents showed an antiproliferative effect. The results showed that these new cisplatin-loaded (M-S-Cho-SA) nanoparticles are good candidates for thermotherapy in cancer treatment in the future, as they can provide selectivity by site-specific targeting and hold onto an alternative magnetic field due to the magnetic nature of the nanoparticles.

Recovery of Phosphate(V) Ions from Water and Wastewater Using Chitosan-Based Sorbents Modified-A Literature Review

Over the past two decades, there has been increasing interest in the use of low-cost and effective sorbents in water treatment. Hybrid chitosan sorbents are potential materials for the adsorptive removal of phosphorus, which occurs in natural waters mainly in the form of orthophosphate(V). Even though there are numerous publications on this topic, the use of such sorbents in industrial water treatment and purification is limited and controversial. However, due to the explosive human population growth, the ever-increasing global demand for food has contributed to the consumption of phosphorus compounds and other biogenic elements (such as nitrogen, potassium, or sodium) in plant cultivation and animal husbandry. Therefore, the recovery and reuse of phosphorus compounds is an important issue to investigate for the development and maintenance of a circular economy. This paper characterizes the problem of the presence of excess phosphorus in water reservoirs and presents methods for the adsorptive removal of phosphate(V) from water matrices using chitosan composites. Additionally, we compare the impact of modifications, structure, and form of chitosan composites on the efficiency of phosphate ion removal and adsorption capacity. The state of knowledge regarding the mechanism of adsorption is detailed, and the results of research on the desorption of phosphates are described.

Magnesium-enriched poultry manure enhances phosphorus bioavailability in biochars

Pyrolysis of calcium-rich feedstock (e.g., poultry manure) generates semi-crystalline and crystalline phosphorus (P) species, compromising its short-term availability to plants. However, enriching poultry manure with magnesium (Mg) before pyrolysis may improve the ability of biochar to supply P. This study investigated how increasing the Mg/Ca ratio and pyrolysis temperature of poultry manure affected its P availability and speciation. Mg enrichment by ∼2.1% increased P availability (extracted using 2% citric and formic acid) by 20% in Mg-biochar at pyrolysis temperatures up to 600 °C. Linear combination fitting of P K-edge XANES of biochar, and Mg/Ca stoichiometry, indicate that P species, mainly Ca-P and Mg-P, are altered after pyrolysis. At 300 °C, adding Mg as magnesium hydroxide [Mg(OH)₂] created MgNH₄PO₄ (18%) and Mg₃(PO₄)₂.8H₂O (23%) in the biochar, while without addition of Mg Ca₃(PO₄)₂ (11%) predominated, both differing only for pyrophosphate, 33 and 16%, respectively. Similarly, the P L_2,3 edge XANES data of biochar made with Mg were indicative of either MgHPO₄.3H₂O or Mg₃(PO₄)₂.8H₂O, in comparison to CaHPO₄.2H₂O or Ca₃(PO₄)₂ without Mg. More importantly, hydroxyapatite [Ca₅(PO₄)₃(OH)] was not identified with Mg additions, while it was abundant in biochars produced without Mg both at 600 (12%) and 700 °C (32%). The presence of Mg formed Mg-P minerals that could enhance P mobility in soil more than Ca-P, and may have resulted in greater P availability in Mg-enriched biochars. Thus, a relatively low Mg enrichment can be an approach for designing and optimize biochar as a P fertilizer from P-rich excreta, with the potential to improve P availability and contribute to the sustainable use of organic residues.

A magnetically recyclable lignin-based bio-adsorbent for efficient removal of Congo red from aqueous solution

It has been always attractive to design a sustainable bio-derived adsorbent based on industrial waste lignin for removing organic dyes from water. However, existing adsorbent strategies often lead to the difficulties in adsorbent separation and recycling. Herein, we report a novel magnetically recyclable bio-adsorbent of Mg(OH)₂/Fe₃O₄/PEI functionalized enzymatic lignin (EL) composite (EL-PEI@Fe₃O₄-Mg) for removing Congo red (CR) by Mannish reaction and hydrolysis-precipitation. The Mg(OH)₂ and PEI functionalized EL on the surface act as active sites for the removal of CR, while the Fe₃O₄ allows for the easy separation under the help of a magnet. As-obtained EL-PEI@Fe₃O₄-Mg forms flower-like spheres and has a relatively lager surface area of 24.8 m² g^-1 which is 6 times that of EL. The EL-PEI@Fe₃O₄-Mg exhibits a relatively high CR adsorption capacity of 74.7 mg g^-1 which is 15 times that of EL when initial concentration is around 100 mg L^-1. And it can be easily separated from water by applying an external magnetic field. Moreover, EL-PEI@Fe₃O₄-Mg shows an excellent anti-interference capability according to the results of pH values and salt ions influences. Importantly, EL-PEI@Fe₃O₄-Mg possesses a good reusability and a removal efficiency of 92 % for CR remains after five consecutive cycles. It is illustrated that electrostatic attraction, π-π interaction and hydrogen binding are primary mechanisms for the removal of CR onto EL-PEI@Fe₃O₄-Mg. This work provides a novel sustainable strategy for the development of highly efficient, easy separable, recyclability bio-derived adsorbents for removing organic dyes, boosting the efficient utilization of industrial waste lignin.

Chitosan Nanoparticles as Potential Nano-Sorbent for Removal of Toxic Environmental Pollutants

Adsorption is the most widely used technique for advanced wastewater treatment. The preparation and application of natural renewable and environmentally friendly materials makes this process easier and more profitable. Chitosan is often used as an effective biomaterial in the adsorption world because of its numerous functional applications. Chitosan is one of the most suitable and functionally flexible adsorbents because it contains hydroxyl (-OH) and amine (-NH₂) groups. The adsorption capacity and selectivity of chitosan can be further improved by introducing additional functions into its basic structure. Owing to its unique surface properties and adsorption ability of chitosan, the development and application of chitosan nanomaterials has gained significant attention. Here, recent research on chitosan nanoparticles is critically reviewed by comparing various methods for their synthesis with particular emphasis on the role of experimental conditions, limitations, and applications in water and wastewater treatment. The recovery of pollutants using magnetic nanoparticles is an important treatment process that has contributed to additional development and sustainable growth. The application of such nanoparticles in the recovery metals, which demonstrates a "close loop technology" in the current scenarios, is also presented in this review.

Fabrication of a magnetic Mn(ii) cross-linked chitosan-amine/glutaraldehyde nanocomposite for the rapid degradation of dyes and aerobic selective oxidation of ethylbenzene†

Owing to the great demand for using sustainable, renewable, and widely available materials in catalytic systems for the conversion of waste/toxic material to high value-added and harmless products, biopolymers derived from natural sources have demonstrated great promise as an alternative to state-of-the-art materials that suffer from high costs and limitations. These have encouraged us to design and fabricate a new super magnetization of Mn–Fe₃O₄–SiO₂/amine-glutaraldehyde/chitosan bio-composite (MIOSC-N-et-NH₂@CS-Mn) for advanced/aerobic oxidation process. The morphological and chemical characterization of the as-prepared magnetic bio-composite was assessed using ICP-OES, DR UV-vis, BET, FT-IR, XRD, FE-SEM, HR-TEM, EDS, and XPS techniques. The PMS + MIOSC-N-et-NH₂@CS-Mn system was capable of degrading methylene orange (98.9% of removal efficiency) and selectively oxidizing ethylbenzene to acetophenone (conversion 93.70%, selectivity 95.10% and TOF 214.1 (10³ h⁻¹) within 8.0 min and 5.0 h, respectively. Moreover, MO was efficiently mineralized (TOC removal of ∼56.61) by MIOSC-N-et-NH₂@CS-Mn with 60.4%, 5.20, 0.03 and 86.02% of the synergistic index, reaction stoichiometric efficiency, specific oxidant efficiency, and oxidant utilization ratio in wide pH ranges, respectively. An understanding of its vital parameters and relationship of catalytic activity with structural, environmental factors, leaching/heterogenicity test, long-term stability, inhibitory effect of anions in water matrix, economic study and response surface method (RSM) were evaluated in detail. Overall, the prepared catalyst could be employed as an environmentally friendly and low-cost candidate for the enhanced activation of PMS/O₂ as an oxidant. Additionally, MIOSC-N-et-NH₂@CS-Mn exhibited great stability, high recovery efficiency, and low metal leaching, which eliminated the harsh condition reaction and supplied practical application performance for water purification and selective aerobic oxidation of organic compounds.

Optimization of the catalytic degradation of dyes and aerobic oxidation of ethylbenzene by Mn@Cross-linked Magnetic Chitosan-Amin-Glutaraldehyde.

Rapid and Efficient Removal of Anionic Dye in Water Using a Chitosan-Coated Iron Oxide-Immobilized Polyvinylidene Fluoride Membrane

Anionic dyes are one of the most serious contaminants in water as these molecules are known to be toxic to many living organisms. Herein, we report the development of functionalized polyvinylidene fluoride membranes modified with chitosan-coated iron oxide nanomaterials (Fe-PVDF) for the efficient treatment of anionic dye-contaminated water. Aqueous solutions of anionic dyes could be captured rapidly by passing through the functionalized membrane under reduced pressure. Under neutral conditions, Fe-PVDF showed a maximum removal capacity of 74.6 mg/g for Evans blue (EB) through the adsorption process. In addition, the adsorption capacity was significantly enhanced up to 434.78 mg/g under acidic conditions. The adsorption process for EB matched well with the Langmuir model, indicating monolayer adsorption of the dye to the membrane surface. Moreover, Fe-PVDF can be reusable by a simple washing step in an alkaline solution, and thus, the composite membrane was applied several times without a significant decrease in its adsorption performance. The same composite membrane was further applied to the removal of five other different anionic dyes with high efficiencies. The adsorption mechanism can be explained by the electrostatic interaction between the positively charged chitosan and the negatively charged dye as well as the affinity of the sulfate groups in dye molecules for the surface of the iron oxide nanoparticles. The easy preparation and rapid decolorization procedures make this composite membrane suitable for efficient water treatment.

Recent developments in alginate-based adsorbents for removing phosphate ions from wastewater: a review

The huge development of the industrial sector has resulted in the release of large quantities of phosphate anions which adversely affect the environment, human health, and aquatic ecosystems. Naturally occurring biopolymers have attracted considerable attention as efficient adsorbents for phosphate anions due to their biocompatibility, biodegradability, environmentally-friendly nature, low-cost production, availability in nature, and ease of modification. Amongst them, alginate-based adsorbents are considered one of the most effective adsorbents for removing various types of pollutants from industrial wastewater. The presence of active COOH and OH^- groups along the alginate backbone facilitate its physical and chemical modifications and participate in various possible adsorption mechanisms of phosphate anions. Herein, we focus our attention on presenting a comprehensive overview of recent advances in phosphate removal by alginate-based adsorbents. Modification of alginate by various materials, including clays, magnetic materials, layered double hydroxides, carbon materials, and multivalent metals, is addressed. The adsorption potentials of these modified forms for removing phosphate anions, in addition to their adsorption mechanisms are clearly discussed. It is concluded that ion exchange, complexation, precipitation, Lewis acid-base interaction and electrostatic interaction are the most common adsorption mechanisms of phosphate removal by alginate-based adsorbents. Pseudo-2^nd order and Freundlich isotherms were figured out to be the major kinetic and isotherm models for the removal process of phosphate. The research findings revealed that some issues, including the high cost of production, leaching, and low efficiency of recyclability of alginate-based adsorbents still need to be resolved. Future trends that could inspire further studies to find the best solutions for removing phosphate anions from aquatic systems are also elaborated, such as the synthesis of magnetic-based alginate and various-shaped alginate nanocomposites that are capable of preventing the leaching of the active materials.

Magnetic chitosan microspheres: An efficient and recyclable adsorbent for the removal of iodide from simulated nuclear wastewater

The efficient and recyclable magnetic chitosan microspheres (MCMs) were successfully synthesized to remove iodide from nuclear wastewater and characterized through XRD, FTIR, SEM, EDS, VSM, TGA and XPS. The characterization results indicated that the MCMs exhibited smooth spherical morphology and good magnetic properties. The removal potential of MCMs was investigated for iodide (I^-) anions at different conditions. From pH 3 to pH 9, MCMs performed the high I^- removal efficiency (>90%). The maximum I^- removal capacity of MCMs was up to 0.8087 mmol g^-1 at 298 K, well-fitting with the pseudo-second-order and Sips models. Furthermore, the I^- removal efficiency of MCMs still maintained more than 91% after five adsorption-desorption cycles, performing good regeneration and reusability. This study is expected to prompt the MCMs to become an efficient and recyclable biosorbent for iodide removal from nuclear wastewater.

Removal of Phosphates in Aqueous Solution by Adsorption on Calcium Oxide

The aim of this work is the removal of phosphates from an aqueous solution by adsorption on a new, inexpensive adsorbent, calcium oxide. We have also shown interest in the choice of removal method, which is adsorption. The kinetic study of the removal of phosphate ions by adsorption on calcium oxide allowed us to calculate the value of adsorption capacity as a function of the parameters affecting adsorption: Amount of adsorbent, initial concentration of phosphate ion solution, pH of the mixture and temperature. The study of adsorption isotherms showed that the Freundlich model is the most appropriate for the phenomenon of phosphate ion adsorption. Modeling of the kinetic data by the pseudo-first order and pseudo-second order equations shows that the adsorption process is best described by the second order equation. Thermodynamic parameters such as enthalpy ΔH°, entropy ΔS° and free enthalpy ΔG° were also evaluated to determine the nature of adsorption. The results show that the adsorption process is a spontaneous and endothermic physisorption.

Chitosan based adsorbents for the removal of phosphate and nitrate: A critical review

The tremendous development in the industrial sector leads to discharging of the several types of effluents containing detrimental contaminants into water sources. Lately, the proliferation of toxic anions particularly phosphates and nitrates onto aquatic systems certainly depreciates the ecological system and causes a deadly serious problem. Chitosan (Cs) is one of the most auspicious biopolymer adsorbents that are being daily developed for removing of various contaminants from polluted water. This is due to its unparalleled benefits involving biocompatibility, non-toxicity, facile modifications and low-cost production. Nevertheless, chitosan displays considerable drawbacks including low adsorption capacity, low surface area and lack of reusability. Therefore, few findings have been established regarding the aptitude of modified chitosan-based adsorbents towards phosphate and nitrate anions. This review elaborates an overview for the current advances of modified chitosan based-adsorbent for phosphate and nitrate removal, in specific multivalent metals-modified chitosan, clays and zeolite-modified chitosan, magnetic chitosan and carbon materials-modified chitosan. The efforts that have been executed for enriching their adsorption characteristics as well as their possible adsorption mechanisms and reusability were well addressed. Besides, the research conclusions for the optimum adsorption conditions were also discussed, along with emphasizing the foremost research gaps and future potential trends that could motivate further research and innovation to find best solutions for water treatment problems facing the world.

Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

In this study, MIL-101(Fe), MIL-101(Fe,Cu), and graphene oxide (GO)/MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOF-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including adsorption time, pH, temperature, and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis, and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g^-1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m²/g is higher than that of MIL-101(Fe,Cuand MIL-101(Fe),which are 747.75 and 510.66 m²/g, respectively. The adsorption mechanism of phosphate is electrostatic attraction, forming coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

La(OH)3 nanoparticles immobilized on Fe3O4@chitosan composites as novel magnetic nanocatalysts for sonochemical oxidation of benzyl alcohol to benzaldehyde

This work introduces an eco-friendly method for immobilization of La(OH)₃ nanoparticles on modified Fe₃O₄ nanoparticles. The structural and morphological characteristics of the nanocatalyst were determined by various analytical techniques including, FT-IR, EDS, FESEM, VSM and XRD. The catalytic efficiency of the Fe₃O₄@Cs/La(OH)₃ composite as a heterogeneous nanocatalyst was evaluated by selective oxidation of benzylic alcohols to aldehydes. The optimum reaction conditions including time, temperature, nanocatalyst dosage, and solvent were investigated for ultrasound-assisted oxidation processes. Furthermore, the magnetic nanocatalyst was recovered up to seven times without considerable activity loss. Furthermore, the proposed nanocomposite had a remarkable effect on reducing the reaction time and enhancing the yield.

A sustainable synthesis of novel Fe₃O₄@CS/La(OH)₃ as a nanocatalyst for oxidation of benzyl alcohols to benzaldehydes has been developed.

Development of polyaminated chitosan-zirconium(IV) complex bead adsorbent for highly efficient removal and recovery of phosphorus in aqueous solutions

The aim of this work is to examine the adsorption performance and mechanism of phosphorus (P) onto polyethyene polyamine (PEPA) grafted chitosan-zirconium(IV) composite beads (CS-Zr-PEPA) from aqueous solutions. The morphology, functional groups, and surface area of the CS-Zr-PEPA beads were characterized by SEM, FTIR, and BET analysis. Batch adsorption experiments were conducted via different operating parameters such as solution pH, initial phosphate concentration, co-existing anions and temperature. The adsorption kinetics, equilibrium isotherms and adsorption stability of the adsorbent were scrutinized. In comparison with other CS-based beads, the CS-Zr-PEPA had a greater affinity towards P and exhibited a maximum adsorption capacity of 103.96 mg-P/g predicted by Langmuir mode. The reusability studies of CS-Zr-PEPA beads were carried out. The CS-Zr-PEPA beads exhibit preferable sequestration of P through specific interactions, as further demonstrated by studying physicochemical characteristics of the virgin beads and P-adsorbed beads using X-ray photoelectron spectroscopy (XPS). The column performance of CS-Zr-PEPA beads was tested with P-containing wastewater. Results indicated that the developed CS-Zr-PEPA composite beads could be utilized as a promising adsorbent for effective removal and recovery of P from water and wastewater.

Synthesis of Fe3O4/Ag nanohybrid ferrofluids and their applications as antimicrobial and antifibrotic agents

To date, the search for creating stable ferrofluids with excellent properties for biomedical application is one of the challenging scientific and practical investigations. In this study, novel Fe3O4/Ag nanohybrid ferrofluids from iron sand were synthesized using a double-layer method. The Fe3O4/Ag nanocomposites exhibited stable crystallite sizes of 11.8 12.1 nm and 36.8-37.2 nm for Fe3O4 and Ag, respectively. The lattice parameters of the spinel structure Fe3O4 and face-centered cubic Ag were respectively 8.344 Å and 4.091 Å. With increasing Ag amount, the crystallite phase of Ag in the nanocomposites increased from 40.2% to 77.2%. The XPS results confirmed that Fe3O4/Ag nanocomposites were successfully prepared, where Fe3O4 mixed well with Ag via strong ionic bonding. The FTIR results confirmed the presence of Fe3O4/Ag, oleic acid, and dimethyl sulfoxide as the filler, first layer, and second layer, respectively. The as-prepared ferrofluids exhibited superparamagnetic behavior, where the saturation magnetization decreased with increasing Ag content. The Fe3O4/Ag nanohybrid ferrofluids exhibited excellent antimicrobial performance against Bacillus subtilis, Staphylococcus aureus, Escherichia coli, and Candida albicans. More importantly, the Fe3O4/Ag nanohybrid ferrofluids decreased the progression of liver fibrosis-related inflammation and fibrogenic activity on hepatic stellate cells.

Ionic Cross-Linking Fabrication of Chitosan-Based Beads Modified with FeO and TiO2 Nanoparticles: Adsorption Mechanism toward Naphthalene Removal in Seawater from Cartagena Bay Area

Polycyclic aromatic hydrocarbons (PAHs) are complex molecules produced by the thermal decomposition of organic matter in anthropogenic activities. Novel composites with enhanced physicochemical properties aim to overcome limitations such as adsorption capacity, affinity, and stability for PAHs adsorption. Composites based on chitosan are promising due to the good biocompatibility and adsorption properties. This study focuses on the facile preparation of chitosan beads modified with iron oxide (FeO) and titanium dioxide (TiO₂) nanoparticles via ionic cross-linking (Ch-FeO/TiO₂). FeO and TiO₂ were synthesized performing co-precipitation and green chemistry methods, respectively. The characterization evidenced the formation of Ch-FeO/TiO₂ with good crystallinity, excellent thermal stability, and superparamagnetic response, attributed to the presence of FeO and TiO₂ nanoparticles. High thermal stability up to 270 °C was related to the cross-linked chitosan network. The enhanced adsorption mechanism of Ch-FeO/TiO₂ was determined by removing naphthalene from water and seawater samples. The Ch-FeO/TiO₂ showed a higher adsorption capacity of 33.1 mg/g compared to 29.8 mg/g of the unmodified chitosan (un-Ch) beads. This is due to the higher functional surface area of 27.13 m²/g, compared to that of 0.708 m²/g for un-Ch. We found a rapid adsorption rate of 240 min and the maximum adsorption capacity of 149.3 mg/g for Ch-FeO/TiO₂. A large number of actives sites allows for increasing the naphthalene molecules interaction. Adsorption in seawater samples from Cartagena Bay (Colombia) exhibits an outstanding efficiency of up to 90%. These results suggest a promising, cheap, and environmentally friendly composite for remediation of water sources contaminated with complex compounds.

Development of Chitosan Functionalized Magnetic Nanoparticles with Bioactive Compounds

In this study, magnetic maghemite nanoparticles, which belong to the group of metal oxides, were functionalized with chitosan, a non-toxic, hydrophilic, biocompatible, biodegradable biopolymer with anti-bacterial effects. This was done using different synthesis methods, and a comparison of the properties of the synthesized chitosan functionalized maghemite nanoparticles was conducted. Characterization was performed using scanning electron microscopy (SEM) and vibrating sample magnetometry (VSM). Characterizations of size distribution were performed using dynamic light scattering (DLS) measurements and laser granulometry. A chitosan functionalization layer was confirmed using potentiometric titration on variously synthesized chitosan functionalized maghemite nanoparticles, which is important for further immobilization of bioactive compounds. Furthermore, after activation of chitosan functionalized maghemite nanoparticles with glutaraldehyde (GA) or pentaethylenehexamine (PEHA), immobilization studies of enzyme cholesterol oxidase (ChOx) and horseradish peroxidase (HRP) were conducted. Factors influencing the immobilization of enzymes, such as type and concentration of activating reagent, mass ratio between carrier and enzyme, immobilization time and enzyme concentration, were investigated. Briefly, microparticles made using the chitosan suspension cross-linking process (MC2) proved to be the most suitable for obtaining the highest activity of immobilized enzyme, and nanoparticles functionalized with chitosan using the covalent binding method (MC3) could compete with MC2 for their applications.

Non-toxic nano approach for wastewater treatment using Chlorella vulgaris exopolysaccharides immobilized in iron-magnetic nanoparticles

The current study, novel magnetic nano-composite particles (Fe₃O₄@EPS) were successfully synthesized via the co-precipitation of iron (III) chloride and iron (II) sulfate (Fe₃O₄ nanoparticles) with exopolysaccharides (EPS) derived from the microalga Chlorella vulgaris. The physico-chemical nature of the Fe₃O₄@EPS was investigated in depth. Transmission electron microscopy (TEM) results estimated the core-shell nature of Fe₃O₄@EPS aggregated inside the indistinctly layered EPS matrix to be 10-20 nm in size. Scanning electron microscopy-based energy dispersive spectral analysis indicated that elemental Fe was successfully loaded on to the EPS polymeric ion-exchanger at a rate of 63.3% by weight. FT-IR results demonstrated that Fe₃O₄ nanoparticles were successfully modified by the functional groups present in EPS. Fe₃O₄@EPS showed a highly magnetic nature at 5.0 emu/g. The XPS survey spectrum, which showed two major peaks at 724.1 and 710.2 eV revealed the elemental composition and electronic structure of Fe₃O₄ nanoparticles and Fe₃O₄@EPS. Furthermore, nutrient removal from wastewater was studied. Under optimum conditions (3.5 g/L of Fe₃O₄@EPS, pH 7.0 and 13 h of incubation) 91% of PO₄^3- and 85% of NH₄⁺were effectively eliminated. These findings demonstrate the potential of Fe₃O₄@EPS for removing PO₄^3- and NH₄⁺ in wastewater treatment plants.

Mechanism of phosphate removal from aqueous solutions by biochar supported nanoscale zero-valent iron

The purpose of this study was to investigate the removal mechanism of phosphate by rape straw biochar (RSBC) supported nanoscale zero-valent iron (nZVI).