Polyaniline-based nanocomposites for direct methanol fuel cells (DMFCs) - A Recent Review

Effect of Graphene Oxide Addition on the Properties of Electrochemically Synthesized Polyaniline-Graphene Oxide Films

In this work, the electrochemical synthesis of PANI and GO-modified PANI was performed using cyclic voltammetry, varying the amount of GO, 1 mg (PG1), 5 mg (PG5), and 10 mg (PG10) to analyze the effect of the amount of GO on the composite. PANI, PG1, PG5, and PG10 materials were characterized using optical microscopy, SEM, UV-vis, FTIR, Raman, and wettability. A stability test was also carried out by putting the materials to 500 oxidation-reduction cycles using cyclic voltammetry. The synthesis method allowed GO in PANI to be added through a chemical interaction between the two compounds. It was also found that the addition of GO led to an improvement in the hydrophilic character of the composite, which would lead to an improvement in the diffusion of reagents/species when the composites are used in aqueous media processes. The results of the stability test showed that the PG10 material presented a lower % loss of specific capacitance and energy compared with the other materials, which indicates that the GO presence (in the amount specified) improves the stability of the PANI. The PG10 material showed favorable and promising conditions for its use in fuel cell and battery processes.

Promotion of hydrogen evolution from seawater via poly(aniline-co-4-nitroaniline) combined with 3D nickel nanoparticles

This work reports the synthesis of poly (aniline-co-4-nitroaniline) deposited on a three-dimensional nanostructured nickel (3D-Ni) film, where both layers were fabricated via potentiostatic electrodeposition. The obtained electrocatalyst exhibited excellent electrochemical activity for the Hydrogen Evolution Reaction (HER) with small overpotentials of - 195 and - 325 mV at - 10 and - 100 mAcm-2, respectively, and a low Tafel slope of 53.3 mV dec-1 in seawater. Additionally, the electrocatalyst exhibited good stability after 72 h operation under a constant potential of - 1.9 V vs. RHE. The efficient HER performance of the as-prepared catalyst was found to originate from the synergy between the conducting polymer and three-dimensional nickel nanoparticles with a large electrochemical active surface area. Moreover, the results obtained from electrochemical impedance spectroscopy (EIS) measurements revealed that the presence of 3D-Ni layer improved the kinetics of HER by reducing the charge transfer resistance for the electrocatalyst.

Modified Cellulose Proton-Exchange Membranes for Direct Methanol Fuel Cells

A direct methanol fuel cell (DMFC) is an excellent energy device in which direct conversion of methanol to energy occurs, resulting in a high energy conversion rate. For DMFCs, fluoropolymer copolymers are considered excellent proton-exchange membranes (PEMs). However, the high cost and high methanol permeability of commercial membranes are major obstacles to overcome in achieving higher performance in DMFCs. Novel developments have focused on various reliable materials to decrease costs and enhance DMFC performance. From this perspective, cellulose-based materials have been effectively considered as polymers and additives with multiple concepts to develop PEMs for DMFCs. In this review, we have extensively discussed the advances and utilization of cost-effective cellulose materials (microcrystalline cellulose, nanocrystalline cellulose, cellulose whiskers, cellulose nanofibers, and cellulose acetate) as PEMs for DMFCs. By adding cellulose or cellulose derivatives alone or into the PEM matrix, the performance of DMFCs is attained progressively. To understand the impact of different structures and compositions of cellulose-containing PEMs, they have been classified as functionalized cellulose, grafted cellulose, acid-doped cellulose, cellulose blended with different polymers, and composites with inorganic additives.

Reduced Graphene Oxide/Carbon Paper for the Anode Diffusion Layer of a Micro Direct Methanol Fuel Cell

The diffusion layer (DL) in the structure of the membrane electrode assembly (MEA) of a micro direct methanol fuel cell (μDMFC) plays an essential role in reactant/product mass transfer and catalyst loading. The material selection and structure design of the μDMFC affects its performance. In this work, a reduced graphene oxide/carbon paper (rGO/CP) was proposed and prepared for the anode DL of a μDMFC. It was prepared using electrophoretic sedimentation combined with an in situ reduction method. The rGO/CP reduced the cell's ohmic and charge transfer resistances. Meanwhile, it provided more significant mass transfer resistance to reduce the methanol crossover, allowing the cell to operate stably at higher concentrations for a longer duration than conventional μDMFCs. The experimental results showed that the maximum power density increased by 53% compared with the traditional anode DL of carbon paper.

High performance poly(isatin alkyl-terphenyl)s proton exchange membranes with flexible alkylsulfonated side groups

Hydrocarbon-based polymer proton exchange membranes (PEMs) free of heteroatom linkages are supposed to be an attractive alternative for the most advanced perfluorosulfonic acid PEMs, but it is challenging to synthesize them. Here we disclosed a series of aliphatic chain-containing poly(isatin diphenyl-co-terphenyl)(PIDT) copolymers, which were conveniently prepared by superacid-catalyzed Friedel-Crafts polycondensation. Subsequently, the sulfonated copolymer (SPIDT) membranes were prepared by the grafting of side-chain sulfonic acid groups. Due to the formed continuous and efficient nanoscale proton transport channel, these PEMs exhibited excellent proton conductivity showing 186 mS/cm at 80°C, higher than Nafion115 (150 mS/cm). Meanwhile, the prepared membranes exhibited good oxidative stability. The residual weight of the membranes is still greater than 98 wt % after 1 h immersion in Fenton’s reagent at 80°C. Notably, the direct borohydride-hydrogen fuel cell (DBHFC) equipped with SPIDT-50 membrane as the diaphragm showed the peak power density of 71 mW•cm−2 at 25°C, which was greater than that of Nafion115 (63 mW•cm−2). Therefore, the hydrocarbon-based PEMs prepared in this study show promise for application in fuel cells.

Autogenous Oxidation/Reduction of Polyaniline in Aqueous Sulfuric Acid

In this work, we have shown through open circuit potential experiments that in aqueous sulfuric acid solutions, a thick polyaniline film undergoes autogenous oxidation when reduced below a threshold potential and autogenous reduction when oxidized above the threshold potential. This phenomenon is associated with the high resonance stability of polarons in long polyaniline chains present in thicker films. We have determined the rates of these reactions using a linear sweep chronopotentiometry technique. We propose that the oxidation reaction of polyaniline produces polarons with a concomitant reduction of hydrogen ions to hydrogen radicals, which further combine with each other to produce the hydrogen molecule in the absence of dissolved oxygen. On the other hand, at high potentials polarons are reduced with the concomitant oxidation of water to hydroxyl radicals. Both the radicals are stabilized due to the interaction of their unpaired electrons with pi-electrons of the aromatic rings of the polymer backbone. At the equilibrium value of the open circuit potential, both the hydrogen radicals and hydroxyl radicals are generated at equal rates and react with each other to form water.