Influence of crystallization conditions on the tensile properties of radiation crosslinked, vitamin E stabilized UHMWPE

Biaxial fatigue crack propagation behavior of ultrahigh molecular weight polyethylene reinforced by carbon nanofibers and hydroxyapatite

Ultrahigh molecular weight polyethylene (UHMWPE) artificial joint has remained the preferred polymer component in total joint replacement surgery. However, more and more concerns have been raised about the failure of UHMWPE components due to the initiation and propagation of cracks at the notches with fixed functions. For this reason, biaxial fatigue crack growth (FCG) experiments of UHMWPE reinforced by carbon nanofibers (CNF) and hydroxyapatite (HA) were carried out using elastic-plastic fracture mechanics theory. The FCG resistance of UHMWPE, UHMWPE/CNF, and UHMWPE/HA was compared, and the effects of stress ratio (R) value and phase difference on FCG rate were investigated. At the same time, the influence of loading path was considered, and the corresponding crack path was analyzed. Results suggest that UHMWPE/CNF has better FCG resistance and the FCG rate increases with the increase of R value and the existence of 180° phase difference. In addition, crack bifurcation behavior is not observed under nonproportional loading conditions. The findings in this study will provide experimental validation and data support for better clinical application of UHMWPE-modified materials.

Elastoplastic behavior of highly cross-linked and vitamin E-stabilized polyethylene - A biomechanical study

BACKGROUND

Vitamin E-stabilized cross-linked polyethylene has been touted to alleviate the negative effects of oxidation. Although it has demonstrated significant improvements in wear resistance, bio-tribology, and oxidative resistance, little is known about the effect of antioxidants and dosage of cross-linking on the mechanical strength. This study aimed to evaluate the mechanical properties of these novel materials, which are commonly used in orthopedic implants.

METHODS

Samples of different polymers were prepared with various levels of cross-linking and with or without vitamin E-stabilization and then tested according to ASTM D695 and D638. The elastoplastic characteristics under compression and tension were compared between the groups.

FINDINGS

Vitamin E-stabilized cross-linked polyethylene showed a significant increase in elastic modulus over other groups, with a maximum increase of 26% in compression and 40% in tension when compared to the highly cross-linked group without vitamin E stabilization. The elastoplastic behavior under compression differed to that in tension for all polymers, demonstrating the anisotropic characteristics of these polymers.

INTERPRETATION

The lower mechanical strength of highly cross-linked polyethylene has been a complication with the use of this polymer in orthopedic liners. This current study suggests that vitamin E-stabilized cross-linked polyethylene could be a suitable alternative material for knee implants because of its improved strength in resisting external forces.

Influence of analyzed lubricant volumes on the amount and characteristics of generated wear particles from three different types of polyethylene liner materials

The articulating components of artificial joints consist mainly of metals, ceramics, or polymers. Resulting abrasive wear particles can promote osteolysis and aseptic loosening of the endo-prosthetic implants. Ultra-high-molecular-weight-polyethylene is the material used most for bearing couples in total hip replacement. In the present study, three types of polyethylene (PE) liners varying in material composition, i.e., (1) conventional PE (C-PE), (2) sequentially cross-linked PE (SX-PE), (3) cross-linked PE blended with vitamin E (EX-PE) articulating with two types of femoral heads were used. After ultrasound treatment of each simulator lubricant, different concentrations (0.1/0.25/0.5/1.0 mL) were taken and dissolved in hydrochloric acid (37%) in a similar manner. The aim was to analyze the characteristics of wear particles generated in a hip simulator, with respect to different volumes of the lubricant. Within the scope of particle analysis, distinct alterations for particle characteristics were determined in the lubricant volumes and types of PE material used. A significant decrease in particle number for SX-PE liners, compared to the C-PE inserts and even more for EX-PE inserts, was detected at each lubricant volume. Particle morphologies varied depending on PE material. Alterations in particle size and other morphologic parameters between the four tested volumes, could be proven for each PE type. In general, particle sizes and parameters (e.g., length and width) increased with increasing serum volumes. In conclusion, the chosen volume of the simulator lubricant used for particle analysis has a crucial influence on detected particle number, size distribution, and morphologic parameters. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1299-1306, 2018.