Evaluation of mechanical and optical behavior of current esthetic dental restorative CAD/CAM composites

Effect of "fast"-crystallization and simultaneous glazing on physicochemical properties of lithium-disilicate CAD/CAM ceramic

OBJECTIVE

Evaluate the impact of a "fast" crystallization and simultaneous-glazing on the physicochemical properties of lithium-disilicate CAD/CAM-ceramic.

METHODS

Lithium-disilicate bars and crowns (IPS e.max CAD, Ivoclar-Vivadent) were divided into four groups (n = 30): WG/F (WG=with glaze/F=fast crystallization), NG/F (NG=no glaze), WG/C (C=conventional crystallization), and NG/C. A liquid/powder glaze system was used (IPS Ivocolor®, Ivoclar-Vivadent). Specimens were crystallized (Programat P310, Ivoclar-Vivadent) using the P161 program for C (approx. 20-25 min), and P165 for F (approx. 14-16 min). Bars (n = 30) underwent three-point bending tests (flexural strength-FS in MPa and modulus of elasticity-E in GPa) using a universal testing machine. Crowns were analyzed via scanning electron microscopy (SEM) after selective etching, and to Raman, FTIR-ATR, and X-ray diffraction (XRD) spectroscopies to assess chemical composition.

RESULTS

For FS, both factors/interaction were statistically significant. C (427.48±42.41 MPa) showed significantly higher values than F (409.82±38.82 MPa). WG (398.32±29.80 MPa) exhibited significantly lower FS than NG (438.21±41.77 MPa). For E data, both factors/interaction were significant. NG (90.28±14.71 GPa) displayed higher E than WG (83.07±5.69 GPa), while C (90.08±12.98 GPa) exhibited higher E than F (83.46±9.40 GPa). NG/C showed the best results for both variables. F groups showed (SEM) porous surfaces and crack-like marks on crystals. FTIR, Raman and XRD spectra confirmed the typical composition of a lithium-disilicate glass ceramic, and some attenuated signals and structural variations (XRD) in WG.

CONCLUSIONS

"Fast" crystallization and simultaneous-glazing produced weaker/less-rigid structures with irregular crystals and glassy phases. Simultaneous glazing may have hindered proper thermal distribution during crystallization.

SIGNIFICANCE

"Fast" crystallization and simultaneous glazing with non-recommended systems, can adversely affect the final properties of lithium disilicate restorations.

Translucency and colour masking ability of hybrid CAD/CAM materials with different thicknesses: in vitro study

OBJECTIVE

To evaluate effect of material thickness and translucency of two different hybrid CAD/CAM materials on their masking ability.

MATERIALS AND METHODS

40 rectangular-shaped specimens (12 × 14 mm) were obtained from Vita Enamic and Grandio blocks at 0.5 and 1 mm-thick (n = 10/group). Colour parameters of specimens were measured on PMMA tooth-coloured replica backgrounds (A2, C4) and black, white backings using dental spectrophotometer. Translucency parameter (TP) and masking ability (∆E00) values of tested materials with 0.5, and 1 mm thicknesses were calculated. Quantitative variables were compared between groups using student t-test.

RESULTS

TP and ∆E00 significantly decreased as thickness of tested materials increased. Grandio showed significantly higher TP values. There were significantly lower ΔE00 values for Vita Enamic compared to Grandio at 1 mm thickness and inversely insignificant at 0.5 mm. The 0.5 mm-thick ∆E00 of tested materials was above clinical acceptability threshold, whereas, 1 mm-thick did not exceed showing better masking properties.

CONCLUSIONS

Thickness is more effective for colour masking than translucency. In thin thickness, the masking ability is less effective, irrespective of tested materials. Translucency of tested materials was affected by their composition. Both hybrid CAD/CAM materials are promising alternatives for masking dark discolouration at 1 mm-thick.

In Vitro Assessment of a New Block Design for Implant Crowns with Functional Gradient Fabricated with Resin Composite and Zirconia Insert

This study aims to evaluate and compare the mechanical resistance, fatigue behavior and fracture behavior of different CAD/CAM materials for implant crowns. Eighty-eight implant crowns cemented-screwed with four sample groups: two monolithic G1 Zirconia (control) and G3 composite and two bi-layered G2 customized zirconia/composite and G4 prefabricated zirconia/composite. All static and dynamic mechanical tests were conducted at 37 °C under wet conditions. The fractographic evaluation of deformed and/or fractured samples was evaluated via electron microscopy. Statistical analysis was conducted using Wallis tests, which were performed depending on the variables, with a confidence interval of 95%, (p < 0.05). The Maximum Fracture Strength values displayed by the four groups of samples showed no statistically significant differences. The crown-abutment material combination influenced the failure mode of the restoration, transitioning from a fatigue fracture type located at the abutment-analog connection for monolithic materials (G1 and G3) to a brittle fracture located in the crown for bi-layered materials (G2 and G4). The use of layered crown materials with functional gradients appears to protect the crown/abutment connection area by partially absorbing the applied mechanical loads. This prevents catastrophic mechanical failures, avoiding long chairside time to solve these kinds of complications.

3D-printed intracoronal restorations, occlusal and laminate veneers: Clinical relevance, properties, and behavior compared to milled restorations; a systematic review and meta-analysis

OBJECTIVES

To assess the feasibility of producing 3D-printed intracoronal restorations, thin and ultrathin veneers, and to compare their mechanical behavior, accuracy, biological, and stain susceptibility to the currently applied milled restorations.

MATERIALS AND METHODS

The databases were comprehensively searched for relevant records up to January 2024 without language restrictions. All studies that assessed 3D-printed partial coverage restorations including inlays, onlays, laminate, and occlusal veneers were retrieved.

RESULTS

The web search yielded a total of 1142 records, with 8 additional records added from websites at a later stage. Only 17 records were ultimately included in the review. The included records compared 3D-printed; alumina-based- and zirconia ceramics, lithium disilicate ceramics, polymer infiltrated ceramics, polyetheretherketone (PEEK), resin composites, and acrylic resins to their CNC milled analogs. The pooled data indicated that it is possible to produce ultrathin restorations with a thickness of less than 0.2 mm. 3D-printed laminate veneers and intracoronal restorations exhibited superior trueness, as well as better marginal and internal fit compared to milled restorations (p < 0.05). However, it should be noted that the choice of materials and preparation design may influence these outcomes. In terms of cost, the initial investment and production expenses associated with 3D printing were significantly lower than those of CNC milling technology. Additionally, 3D printing was also shown to be more time-efficient.

CONCLUSIONS

Using additive manufacturing technology to produce restorations with a thickness ranging from 0.1 to 0.2 mm is indeed feasible. The high accuracy of these restorations, contributes to their ability to resist caries progression, surpassing the minimum clinical threshold load of failure by a significant margin and reliable adhesion. However, before 3D-printed resin restorations can be widely adopted for clinical applications, further improvements are needed, particularly in terms of reducing their susceptibility to stains.

CLINICAL SIGNIFICANCE

3D-printed intracoronal restorations and veneers are more time and cost-efficient, more accurate, and could provide a considerable alternative to the currently applied CNC milling. Some limitations still accompany the resin materials, but this could be overcome by further development of the materials and printing technology.

Material and abutment selection for CAD/CAM implant-supported fixed dental prostheses in partially edentulous patients - A narrative review

Restorative material selection has become increasingly challenging due to the speed of new developments in the field of dental material science. The present narrative review gives an overview of the current indications for implant abutments and restoration materials for provisional and definitive implant-supported fixed dental prostheses in partially edentulous patients. For single implant restorations, titanium base abutments for crowns are suggested as an alternative to the conventional stock- and customized abutments made out of metal or zirconia. They combine the mechanical stability of a metallic connection with the esthetic potential of ceramics. For multiple-unit restorations, conical titanium bases especially designed for bridges are recommended, to compensate for deviating implant insertion axes and angulations. Even though titanium base abutments with different geometries and heights are available, certain clinical scenarios still benefit from customized titanium abutments. Indications for the definitive material in fixed implant restorations depend on the region of tooth replacement. In the posterior (not esthetically critical) zone, ceramics such as zirconia (3-5-Ymol%) and lithium-disilicate are recommended to be used in a monolithic fashion. In the anterior sector, ceramic restorations may be buccally micro-veneered for an optimal esthetic appearance. Lithium-disilicate is only recommended for single-crowns, while zirconia (3-5-Ymol%) is also recommended for multiple-unit and cantilever restorations. Attention must be given to the specific mechanical properties of different types of zirconia, as some feature reduced mechanical strengths and are therefore not indicated for all regions and restoration span lengths. Metal-ceramics remain an option, especially for cantilever restorations.

Effect of polishing and bleaching on color, whiteness, and translucency of CAD/CAM monolithic materials

OBJECTIVE

To evaluate the effect of polishing and bleaching on the recovery of lightness, color, whiteness, and relative translucency parameter (RTP) in CAD/CAM materials and changes in these properties when another staining in coffee was conducted after the treatments.

MATERIALS AND METHODS

Disks of Lava Ultimate (LU), Vita Enamic (VE), IPS Empress CAD (EMP), IPS e.max CAD (EMAX), and Vita Suprinity (VS) were (1) not treated (control), (2) polished with Proxyt or (3) Ceramisté, (4) bleached with Opalescence PF or (5) Whiteness HP Blue, and (6) air polished with Clinpro Prophy Powder. CIE L*a*b* color coordinates were registered at baseline (R0), after staining with coffee for 30 min daily for 36.5 days and treatment (R1), and after another staining (R2). Differences (R1-R0 and R2-R0) in lightness (ΔL00), color (ΔE00), RTP (ΔRTP00), and whiteness (ΔWID) were evaluated by mixed repeated measures ANOVA and 95% confidence intervals (α = 0.05) and interpreted in function of their respective 50:50% PT and AT thresholds. Topography was evaluated by scanning electron microscopy (SEM).

RESULTS

In LU, Opalescence PF and Proxyt decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {\mathrm{R}}_0\right)} $$ , andΔWI D R 1 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_1\hbox{--} {R}_0\right)} $$ and showed lowerΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ , andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ . In VE, all treatments decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , andΔWI D R 1 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_1\hbox{--} {R}_0\right)} $$ , whereasΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ , andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ were lower in Opalescence PF than in the control group. In both moments, ΔE00 and ΔWID in EMP (also ΔL00) and EMAX were higher in Opalescence PF than in the control group, from which the other treatments did not differ in R1-R0. In EMP,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ in Whiteness HP Blue (alsoΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ) and Proxyt were also higher in comparison to the control group and in VS, Ceramisté decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , andΔ R T P 00 R 1 - R 0 $$ \varDelta RT{P}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , whereas Opalescence PF increasedΔRTP 00 R 1 - R 0 $$ {\Delta \mathrm{RTP}}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ .Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ of Ceramisté andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ andΔ R T P 00 R 2 - R 0 $$ \varDelta RT{P}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ of Proxyt were lower than those of the control group.

CONCLUSIONS

The most suitable treatment to recover the lightness, color, whiteness, and RTP without changing these properties after another coffee exposure is material-dependent.

CLINICAL SIGNIFICANCE

Although the effectiveness of the treatment was material-dependent, Proxyt was the only treatment that promoted clinically acceptable changes for both LU and VE, while for purely ceramic materials, this condition was observed with Ceramisté and Clinpro Prophy Powder.

Effect of coffee staining and simulated oral hygiene methods on the color and translucency of a nanoceramic resin

OBJECTIVE

Evaluate the color and translucency of a nanoceramic resin subjected to hygiene practices and immersion in coffee over time.

MATERIALS AND METHODS

Specimens (n = 80, HT and LT, 0.5-mm thick) of a nanoceramic resin were obtained and were divided in groups according to the simulated oral hygiene: no intervention (NT), brushing with an electric brush and water (BN), brushing with an electric brush and toothpaste for 10 s (BT), and immersion in mouthwash for 30 s (MW). Oral hygiene practices were repeated after staining in coffee solution for 15, 48, 336, 1440, 8640, and 35,040 min. Spectral wavelengths were recorded with a spectrophotometer at each time. ∆E00, ∆L', ∆C', ∆H', and TP00 were calculated by CIEDE2000 and were evaluated by 2-way ANOVA, repeated measures ANOVA, and Tukey's HSD test (α = 0.05).

RESULTS

ANOVA showed significance among factors for ΔE00 (p < 0.05), with higher ΔE00 for NT-HT (11.7) and NT-LT (11.2). After T6 (2-year simulation), the lowest values were found for BT-HT (5.3) and BT-LT (4.9). All groups showed a reduction in lightness and translucency and increased chroma and hue. However, the smallest variations were found in the BT groups (p < 0.05).

CONCLUSIONS

Brushing with toothpaste effectively minimized the color change of NCRs caused by coffee staining.

CLINICAL SIGNIFICANCE

Oral hygiene practices, such as brushing with toothpaste, might be important to minimize staining of nanoceramic resin restorations, especially in patients who frequently consume coffee.

Assessment of color stability and translucency of various CAD/CAM ceramics of different compositions and Thicknesses: An in vitro study

Background

Translucency and optical characteristics significantly affect the aesthetics of ceramic restorations. The introduction of new virgilite crystals to novel ceramic advanced lithium disilicate through a matrix firing process enhances the material's strength and aesthetic quality according to the manufacturer.

Materials and Methods

Four types of CAD/CAM ceramics; lithium disilicate (LD), leucite reinforced (LR), advanced lithium disilicate (ALD), and zirconia-reinforced lithium silicate (ZLS) exposed to different staining solutions (tea, cola, coffee, and distilled water). Each ceramic type had 120 specimens, divided into subgroups based on thickness (0.5 mm, 1 mm, and 1.5 mm). Color changes (ΔE00) and translucency parameters (TP00) were measured after thermocycling, and spectrophotometry was employed to evaluate ΔE00 and TP00 after 1, 7, and 30 days of exposure to the staining solutions.

Results

ZLS exhibited the lowest color stability, while lithium LD and ALD displayed the highest. Thickness significantly affected color stability, with 0.5 mm thickness showing the least change. The duration of exposure also impacted color changes, with 30 days causing the most significant shift. LD demonstrated the highest translucency. Coffee and tea induced more pronounced reductions in translucency and color stability compared to the control group.

Conclusions

Material structure, thickness, staining solution, and exposure duration significantly influenced the color stability and translucency of CAD/CAM ceramics, with LD and ALD demonstrating superior color stability and LD exhibiting the highest translucency.

Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns

OBJECTIVES

The purpose of this study is to evaluate the bond strength of different computer-aided design / computer-aided manufacturing (CAD/CAM) hybrid ceramic materials following different pretreatments.

METHODS

A total of 306 CAD/CAM hybrid material specimens were manufactured, n = 102 for each material (VarseoSmile Crownplus [VSCP] by 3D-printing; Vita Enamic [VE] and Grandio Blocs [GB] by milling). Each material was randomly divided into six groups regarding different pretreatment strategies: control, silane, sandblasting (50 μm aluminum oxide particles), sandblasting + silane, etching (9% hydrofluorics acid), etching + silane. Subsequently, surface roughness (Ra) values, surface free energy (SFE) were measured. Each specimen was bonded with a dual-cured adhesive composite. Half of the specimens were subjected to thermocycling (5000 cycles, 5-55 °C). The shear bond strength (SBS) test was performed. Data were analyzed by using a two-way analysis of variance, independent t-test, and Mann-Whitney-U-test (α = 0.05).

RESULTS

Material type (p = 0.001), pretreatment strategy (p < 0.001), and the interaction (p < 0.001) all had significant effects on Ra value. However, only etching on VSCP and VE surface increased SFE value significantly. Regarding SBS value, no significant difference was found among the three materials (p = 0.937), while the pretreatment strategy significantly influenced SBS (p < 0.05). Etching on VSCP specimens showed the lowest mean value among all groups, while sandblasting and silane result in higher SBS for all test materials.

CONCLUSIONS

The bond strength of CAD/CAM hybrid ceramic materials for milling and 3D-printing was comparable. Sandblasting and silane coupling were suitable for both millable and printable materials, while hydrofluoric etching should not be recommended for CAD/CAM hybrid ceramic materials.

CLINICAL RELEVANCE

Since comparable evidence between 3D-printable and millable CAD/CAM dental hybrid materials is scarce, the present study gives clear guidance for pretreatment planning on different materials.

Cutting Efficiency of Diamond Grinders on Composite and Zirconia

This in vitro study was carried out to compare the cutting efficiency of diamond grinders on zirconia and resin-based composite materials. Grinders were employed with a special holder for the handpiece to apply a constant load (160 g) for resin-based composite (8 cuts, 40 s each) and zirconia materials (4 cuts, 5 min each; n = 10 for each material and grinder). To assess the efficiency of the grinders, weight measurements of the material were taken before and after the grinding process. Scanning electron micrographs were captured for instrument surfaces before and after testing and for the resulting surface of the materials. In the resin-based composite group, there were significant differences in weight removal between the burs for both the baseline (first cut; p = 0.009) and removal after the eighth cut (p = 0.049). Statistically significant decreases in weight removal compared to the baseline values were noted for the third, fourth, sixth, and seventh steps (p ≤ 0.046). For the zirconia group, significant differences existed in weight removal between the burs for the baseline (first cut; p < 0.001) and removal after the fourth cut (p < 0.001). A significant positive correlation was observed between removal and the number of cuts (Pearson: 0.673; p < 0.001). A statistically significant decrease in removal compared to the respective baseline value was found for the fourth step (p = 0.006). The initial wear removal and durability significantly differed between the grinders used on resin-based composite and zirconia. Achieving comparable weight removal took five times longer when grinding zirconia compared to the resin-based composite.

Using digital photographs as a tool to assess the clinical color stability of lithium disilicate veneers: A clinical trial

STATEMENT OF PROBLEM

Clinical information regarding the color stability of lithium disilicate veneers by using different methods of evaluation is scarce.

PURPOSE

This clinical trial aimed to evaluate whether digital photographs are a reliable method of clinically assessing the color stability of lithium disilicate veneers. Standardized digital photographs (ELAB) were compared with the VITA Easyshade spectrophotometer (ES) at baseline and at a 6-month follow-up.

MATERIAL AND METHODS

A split-mouth model was used in this randomized clinical trial to assess the performance of ceramic veneers (N=162), which were produced by either the CAD (IPS e.max CAD; n=81) or PRESS technique by heat pressing (IPS e.max PRESS; n=81), including the color dimension assessment. The ELAB evaluation was performed by making digital photographs with polarized light and a white balance (WhiBal) card. These data were transferred to the Adobe Lightroom CC2015 software program in RAW extension. The Digital Color Meter App (Apple) was used to measure L∗, a∗, and b∗ coordinates in this method. The ES color evaluation was performed with a spectrophotometer (Easy Shade) (control group) in the CIELab system. Measurements were performed 1 week after cementation (baseline) and at a 6-month follow-up. Data collected by the ELAB and ES methods were analyzed by a blinded calibrated operator to calculate ΔE by using the Mann-Whitney-Wilcoxon test (α=.05).

RESULTS

For all periods, the comparison among ELAB and ES methods (P=.331), CAD×PRESS by ELAB (P=.658), and CAD×PRESS by ES (P=.833) showed no statistically significant differences.

CONCLUSIONS

Standardized digital photographs (ELAB) were shown to be a straightforward and available resource for evaluating the color stability of lithium disilicate veneers, manufactured by CAD or PRESS.

CAD-CAM resin-ceramic material wear: A systematic review

STATEMENT OF PROBLEM

The increasing use of computer-aided design and computer-aided manufacturing (CAD-CAM) systems has led to the development of resin-ceramic materials that meet the requirements of minimally invasive dentistry, including the resin nanoceramic (RNC) and polymer-infiltrated ceramic network (PICN). The wear characteristics of these materials are unclear.

PURPOSE

The purpose of this systematic review was to compare the wear resistance of resin-ceramic materials when compared with one another or with lithium disilicate glass-ceramics.

MATERIAL AND METHODS

The PubMed, Scopus, and DOSS search engines were used to identify articles published between 2013 and 2021. Two independent researchers conducted the systematic review by following the preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidelines and by following a combination of keywords.

RESULTS

Of a total of 310 articles, 26 were selected, including only 1 clinical study. Among these, 15 compared resin-ceramic materials with each other, while 11 compared resin-ceramic materials with lithium disilicate ceramics. Two types of wear were used to compare the materials: attrition and abrasion. The most commonly studied materials were 2 RNCs (Lava Ultimate and Cerasmart), 1 PICN (Vita Enamic), and 1 ceramic (IPS e.max CAD). Among the resin-ceramic materials, the PICN (Vita Enamic) showed less wear than the RNCs. Of the RNCs, Cerasmart had less attrition wear and less wear of the opposing teeth.

CONCLUSIONS

Lithium disilicate glass-ceramics have a higher wear resistance than resin-ceramic materials, but they cause more wear of the opposing teeth.

Effect of coffee thermocycling on the color and translucency of milled and 3D printed definitive restoration materials

STATEMENT OF PROBLEM

Research on the color and translucency properties of 3-dimensionally (3D) printed definitive resins and the effect of coffee thermocycling on these properties is lacking.

PURPOSE

The purpose of this in vitro study was to investigate the effect of coffee thermocycling on the color and translucency parameters of the milled and 3D printed materials used for definitive restorations.

MATERIAL AND METHODS

Plate-shaped specimens (12×12×1 mm) of 3 milled (IPS e.max CAD (LDS), Vita Enamic (PICN), Cerasmart (RNC)) and two 3D printed (VarseoSmile Crownplus (VSP), Permanent Crown (PC)) were fabricated (n=12). The brightness (L*), red-green (a*), and yellow-blue (b*) parameters were measured with a spectrophotometer before and after 10 000 coffee thermocycles. The relative translucency parameters (RTP00) and color change were calculated using the CIEDE2000 formula. Stainability (ΔE00) and translucency differences (ΔRTP00) were evaluated. Data were analyzed with the Kruskal-Wallis, Mann-Whitney U, and Wilcoxon tests. The Spearman correlation test was used to analyze the ΔE00 and ΔRTP00 values (α=.05).

RESULTS

The type of material and coffee thermocycling significantly affected the evaluated parameters at both measurement periods (P=.001). Coffee thermocycling decreased the L* and RTP00 values while increasing the a* and b* values (P=.001). The highest ΔE00 values were found in VSP and PC, which were statistically similar (P=.291), while the highest | ΔRTP00 | values were observed for VSP (P=.001). The lowest ΔE00 and | ΔRTP00 | values were found in LDS (P=.001). A positive relationship was found between the ΔE00 and | ΔRTP00| values (R=.590, P=.01).

CONCLUSIONS

After coffee thermocycling, all tested materials exhibited a darkened, yellowish, and opaque appearance, although the alterations in color and translucency remained within clinically acceptable thresholds (AT00=1.81) for these materials.

Effects of erosion and abrasion on resin-matrix ceramic CAD/CAM materials: An in vitro investigation

The aim of the study was to evaluate the effects of erosion and abrasion on resin-matrix ceramic CAD/CAM materials [CERASMART (GC); VITA ENAMIC (VITA Zahnfabrik); Lava Ultimate (3 M)] in comparison to feldspar ceramic (VITABLOCS Mark II, VITA Zahnfabrik) and resin composite materials (ceram.x universal, Dentsply Sirona). Daily brushing and acid exposure were simulated using a brushing apparatus and a solution of 0.5 vol% citric acid. Microhardness, surface roughness, and substance loss were measured at baseline and after simulation of 1 and 3 years of function. All materials showed a decrease in microhardness after 3 years and an increase in surface roughness (Ra) after 1 and 3 years. The Ra increase was statistically significantly lower for the resin-matrix ceramics than for feldspar ceramic and similar to composite material. After 3 years, only feldspar ceramic showed no significant substance loss. In conclusion, resin-matrix ceramics demonstrate reduced roughening compared to feldspar ceramics, potentially improving restoration longevity by preventing plaque buildup, but differences in abrasion resistance suggest the need for further material-specific research. Future research should aim to replicate clinical conditions closely and to transition to in vivo trials.

3D printing of ultra-thin veneers made of lithium disilicate using the LCM method in a digital workflow: A feasibility study

OBJECTIVE

This article highlights the feasibility of the additive fabrication of ultra-thin veneers made of lithium disilicate using the lithography-based ceramic manufacturing (LCM) method.

CLINICAL CONSIDERATIONS

An esthetical appealing restoration of anterior teeth with thin ceramic veneers is considered one of the ultimate challenges in restorative dental prosthetics. These sophisticated restorations can be fabricated in different ways. Both analog and digital subtractive manufacturing processes have been used to date. Either of the methods is highly demanding for the dental technician and dental engineering due to the required low ceramic layer thickness.

CONCLUSION

Modern additive manufacturing methods, for example LCM technology, enable the production of ultra-thin lithium disilicate veneers with layer thicknesses of down to 0.2 mm and could therefore represent a viable alternative for this indication in the future.

CLINICAL SIGNIFICANCE

Digital technologies can help streamline workflows, make the outcome more predictable and reproducible, and even further optimize therapeutic restorative options such as highly esthetic veneers for anterior teeth. The reduced material thickness allows for a true non-prep solution or minimally invasive preparation.

Biofilm Formation on Hybrid, Resin-Based CAD/CAM Materials for Indirect Restorations: A Comprehensive Review

Hybrid materials are a recent addition in the field of restorative dentistry for computer-aided design/computer-aided manufacturing (CAD/CAM) indirect restorations. The long-term clinical success of modern dental restorative materials is influenced by multiple factors. Among the characteristics affecting the longevity of a restoration, the mechanical properties and physicοchemical interactions are of utmost importance. While numerous researchers constantly evaluate mechanical properties, the biological background of resin-based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze biofilm formation on the surfaces of novel, hybrid, resin-based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence initial bacterial adhesion; however, most studies focus on in vitro protocols, and in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing an accurate understanding of the bioadhesion phenomenon in the oral cavity.

Comparison of volumetric loss and surface roughness of composite dental restorations obtained by additive and subtractive manufacturing methods

Statement of problem

Permanent crown materials produced with new generation additive manufacturing and traditional subtractive manufacturing materials have not been compared in terms of wear resistance.

Purpose

This study aims to compare the volumetric loss related to wear and resulting surface roughness after aging in a chewing simulator between resin nano ceramics produced with milling technique and permanent crown materials produced with three dimensional (3D) printing.

Materials and methods

Three different hybrid composite-ceramic (HCC) (The three materials are GC: Cerasmart, VE: Vita Enamic, and GV: Grandio Voco.) and one 3D printed definitive crown resin (FormLabs Permanent Crown Resin) were investigated before aging (n:8), the surface roughness of all samples was measured with a profilometer, and 1 randomly selected sample from each subgroup was imaged with scanning electron microscope (SEM). 3D scans of each sample were obtained with a desktop scanner. Thermomechanical aging was performed using a chewing simulator. Four hundred thousand cycles were completed under a vertical occlusal force of 49 ± 0.7 N with a thermal cycle of 1.7 Hz 5-55° and with a dwell time of 120 s, mimicking 2 years of aging. The imaging procedures were repeated, and the change in surface roughness was evaluated. 3D images were also overlapped, and the volumetric loss was calculated with the relevant inspector software. The data obtained were analyzed by two-way ANOVA (p < 0.05).

Result

The results showed significant statistical differences for both parameters (p > 0.05). The highest volumetric loss was found in the GV group while the lowest volumetric loss was in the VE group. The highest surface roughness values were observed in the GV group, while the lowest values belonged to the VE one.

Conclusion

Of the restorative materials evaluated, the VE group is suitable for long-term restorations, whereas the GV one is suitable for medium-term restorations. It is promising in terms of 3D printing technologies that the 3D material gives comparable results with the GV group.

Clinical i̇mplication

Additive manufacturing techniques are a successful method that accelerates the manufacturing process. Permanent crown resins are promising alternatives to conventional production.

In-vitro evaluation of wear characteristics, microhardness and color stability of dental restorative CAD/CAM materials

The aim of this study was to demonstrate the vertical and volumetric wear characteristics of CAD/CAM materials. The microhardness and color stability were evaluated. A polymer infiltrated ceramic network CAD/CAM block, resin nanoceramic CAD/CAM blocks, a resin composite, and enamel tissue were investigated. Samples were loaded in a chewing simulator. Other samples were aged and immersed in coffee. Color change was evaluated using the digital image analysis and a spectrophotometer. The data were analyzed using Kolmogorov-Smirnov, Kruskal Wallis, Mann Whitney U, Friedman, Spearman's rho tests (p<0.05). The lowest level of wear was obtained in enamel tissue group 0.20 (Q1:0.14; Q3:0.27μm). Resin composite group 2.48 (Q1:2.12; Q3:2.92) showed lower level of discoloration. No agreement was obtained between the digital image analysis and spectrophotometer data (Spearman's rho -0.314, p=0.014). Similar wear rate to the natural enamel tissue was obtained for Vita Enamic. Digital image analysis was considered a promising technique for monitoring the color change.

Effect of Thermo-mechanical Cycling on Fracture Resistance of Different CAD/CAM Crowns: An In Vitro Study

AIM

To evaluate the effect of thermo-mechanical cycling (TMC) on fracture resistance of different computer-aided design/computer-aided manufacture (CAD/CAM) crowns.

MATERIALS AND METHODS

A total of 42 CAD/CAM crowns were fabricated on epoxy resin maxillary first premolar teeth and divided into three groups (n = 14) according to the material used: IPS e.max CAD (Ivoclar Vivadent) lithium disilicate (LD), Vita ENAMIC (VE) (VITA Zahnfabrik), Tetric CAD (Ivoclar Vivadent). Also, each group was subdivided into two equal subgroups according to TMC (n = 7). Subgroups (O) without TMC and subgroup (W) with TMC (5-55°C, 30 second, 75,000 cycles). All samples in each group were cemented with a universal bond (Tetric N bond universal) and adhesive resin cement (Variolink Esthetic DC) (Ivoclar Vivadent). Subsequently, the samples were loaded to failure in a universal testing machine at a crosshead speed of 1 mm/min, and the fracture pattern and the fracture resistance in each group were recorded.

RESULTS

Fracture resistance was analyzed by one-way analysis of variance (ANOVA) test, followed by Tukey's post hoc test for pairwise comparison. Fracture resistance showed a significant difference between the tested groups before and after TMC; IPS e.max CAD has the highest value (1233.35 ± 97.72, 1165.73 ± 199.54 N) followed by Tetric CAD (927.62 ± 42.5, 992.04 ± 53.46 N) and Vita ENAMIC has lowest value (506.49 ± 74.24, 354.69 ± 90.36 N).

CONCLUSION

Thermo-mechanical cycling affected the fracture resistance of both polymer-based CAD/CAM crowns.

CLINICAL SIGNIFICANCE

For dental practitioners, both IPS e.max CAD and Tetric CAD can be used clinically for posterior teeth, providing satisfactory results and resistance to fracture. How to cite this article: Elmokadem MI, Haggag KM, Mohamed HR. Effect of Thermo-mechanical Cycling on Fracture Resistance of Different CAD/CAM Crowns: An In Vitro Study. J Contemp Dent Pract 2024;25(1):29-34.

Color Appearance of Various Provisional Restorative Materials for Rehabilitation Upon Aging

OBJECTIVES

 Color stability of provisional restoration is crucial for full mouth reconstruction, which is probably influenced by aging. Therefore, this study evaluated the effect of aging on the color appearance of different provisional materials.

MATERIALS AND METHODS

 Rectangular specimens (10 × 10 × 2 mm) were fabricated from computer-aided design-computer-aided manufacturing (CAD-CAM) (Vita CAD-Temp [VC], TelioCAD [TC], artBloc [RC]), autopolymerized (ProtempIV [PA], Luxatemp [LA], UnifastTrad [UA]), and heat-polymerized polymer (Major C&B [MH]). Each was divided into aging (AG, 5,000 thermocycles of 5°/55°C) and non-aging group (n = 21/group). Color parameters were determined using a spectrophotometer through the CIELAB system. The L*, a*, and b* data were calculated for color appearance (∆E), translucency parameter (TP), contrast ratio (CR), and opalescence parameter (OP) for each.

STATISTICAL ANALYSIS

 An analysis of variance and multiple comparisons were determined for a significant difference in color appearance alteration of materials upon aging (α = 0.05).

RESULTS

 Statistically significant differences of L*, a*, b*, ∆E, TP, CR, and OP due to the effect of types of material (p < 0.05), aging effect (p < 0.05), and their interactions (p < 0.05) were indicated. Aging affects the color appearance, lightness, chromaticity, translucency, contrast, and opalescence of various types of provisional materials. Color appearance alteration of provisional materials was significantly indicated upon aging (p < 0.05) but within the perceivable limit of clinical acceptance (∆E diff < 3.0), except for PA and MH. Color stability of CAD-CAM-based poly-methyl methacrylate (PMMA) and autopolymerized PMMA upon aging were better than bis-acryl resin and heat-polymerized PMMA. The TP, CR, and OP alterations of tested materials upon aging were within the perceivable limit.

CONCLUSION

 Color appearance of provisional restorative materials was influenced by aging. The CAD-CAM-based PMMA and autopolymerized PMMA materials showed better color stability than bis-acryl provisional resin and heat-polymerized PMMA upon aging. Therefore, they were suggested as provisional materials for oral rehabilitation.

Biaxial flexural strength and Weibull characteristics of a resin ceramic material after thermal-cycling

PURPOSE

The purpose of this in vitro study was to compare the flexural strength and Weibull characteristics of 3 different resin-ceramic materials with a zirconia-reinforced lithium silicate material after thermal-cycling.

MATERIAL AND METHODS

Four different computer-aided design and computer-aided manufacturing restorative materials (Vita Enamic, Lava Ultimate, Crystal Ultra, and Vita Suprinity) were tested. A total of 40 Ø12×1.2-mm disks were prepared and divided into 4 groups (n = 10). Their flexural strength was evaluated after 5000 thermal-cycles with a 4-point biaxial flexure test using a universal testing machine. The Weibull modulus and probability of failure were also determined from the biaxial flexural strength data. Data were analyzed with one-way ANOVA and the Tukey pairwise comparison test (α = 0.05).

RESULTS

Significant differences were found among the materials in terms of biaxial flexural strength (p < 0.05). Vita Suprinity had the highest mean ±standard deviation flexural strength (289.1 ± 15.1 MPa), and Vita Enamic had the lowest (100.0 ± 3.2 MPa). The highest Weibull modulus was calculated for Crystal Ultra, followed by Vita Enamic, Lava Ultimate, and Vita Suprinity.

CONCLUSION

Vita Suprinity had the highest flexural strength when compared with the other materials tested. Crystal Ultra had the highest flexural strength among the resin-ceramic materials. The highest Weibull modulus was calculated for Crystal Ultra and the lowest for Vita Suprinity.

Translucency of Lithium-Based Silicate Glass-Ceramics Blocks for CAD/CAM Procedures: A Narrative Review

Amid chairside CAD/CAM materials, the use of lithium-based silicate glass-ceramics (LSGC) has been steadily increasing. This review aims to report on the translucency of these materials and the variables used to measure it. An electronic search was performed within the PubMed database within the period between 2 June 2011 and 11 September 2022. English-language papers investigating the translucency of IPS e.max CAD, Celtra Duo, Suprinity PC, Initial LiSi Block, Amber Mill, N!ce, and CEREC Tessera LSGC CAD/blocks were included in the search strategy. After an initial retrieval of 160 papers, the application of exclusion criteria, and the screening of abstracts and then of full texts, 33 papers were included in the study. The retrieved materials, with different degrees of translucency (LT, HT), were IPS e.max CAD (n = 33), Suprinity PC (n = 8), and Celtra Duo (n = 1). Concerning the examined colors, the most used was A2 (n = 20), followed by A1 (n = 8) and A3 (n = 2). The translucency parameter (TP) was the most used method (n = 30) with respect to the contrast ratio (CR) (n = 11) to assess translucency. Five papers measured both. Several specimens' thicknesses (0.5-4 mm) were investigated, with 1 mm (n = 23) being the most frequently analyzed. While a general tendency could be identified, conflicting results among different papers were reported.

In vitro evaluation of CAD/CAM composite materials

OBJECTIVES

The purpose of this in vitro study was to evaluate the microstructural, elemental and mechanical properties of contemporary computer-aided-design/computer-aided manufacturing (CAD/CAM) resin based composite (RBC) materials.

METHODS

Six CAD/CAM RBC materials [Brilliant CRIOS (Coltene Whaledent AG), Cerasmart (GC), Lava Ultimate (3M ESPE), Tetric CAD (Ivoclar Vivadent), Shofu Block HC (Shofu), Grandio Blocs (VOCO GmbH)] were tested. Ten rectangular blocks (14 Χ 12 Χ 18 mm) for each material, after metallographic grinding and polishing, were subjected to Instrumented Indentation Testing (ΙIT). Martens Hardness (HM), Indentation Elastic Modulus (EIT), Elastic (ηIT) and Creep indices (CIT) were determined according to formulas provided by ISO 14577. The diagonal length of each indentation was measured and HV was determined. The results of HM, EIT, ηΙΤ, HV, and CIT were statistically analyzed by one-way ANOVA and Tukey post hoc test employing the material as a discriminating variable (a = 0.05), while the possible correlations were determined by Spearman's correlation test. One specimen from each group was examined by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX).

RESULTS

Backscattered Electron images and EDX analysis demonstrated differences in size, shape and type of fillers along with elemental composition among materials tested. Statistical significant differences were identified for all mechanical properties tested. Grandio Blocs had the significantly higher HM (953±7 N/mm2), HV (136±1) and EIT (23±1 GPa) followed by Lava Ultimate (ΗM=674±25 N/mm2, HV=105±2, EIT=15±1 GPa). Elastic index ranged from 41% to 52%, with Shofu Block demonstrating the significantly highest ηIT (52 ± 1%) values. Cerasmart had significantly higher CIT value (8.4 ± 0.1%) than all other materials tested, while Grandio Blocs and Lava Ultimate had the lowest ones. Spearman's correlation revealed that all mechanical properties tested exhibited correlations with each other, apart from ηΙΤ.

CONCLUSIONS

The results showed that the CAD/CAM materials tested have differences in their microstructure, elemental composition and mechanical properties.

CLINICAL SIGNIFICANCE

The RBCs tested showed significant differences in mechanical properties and thus differences in clinical performance are anticipated. RBCs with increased filler loading had the most favorable combination of hardness, elastic modulus and creep index indicating that these materials may have better clinical performance under intraoral loading conditions.

Flexural Strength of CAD/CAM Lithium-Based Silicate Glass-Ceramics: A Narrative Review

Amongst chairside CAD/CAM materials, the use of lithium-based silicate glass-ceramics (LSGC) for indirect restorations has recently been increasing. Flexural strength is one of the most important parameters to consider in the clinical selection of materials. The aim of this paper is to review the flexural strength of LSGC and the methods used to measure it.

METHODS

The electronic search was completed within PubMed database from 2 June 2011 to 2 June 2022. English-language papers investigating the flexural strength of IPS e.max CAD, Celtra Duo, Suprinity PC, and n!ce CAD/CAM blocks were included in the search strategy.

RESULTS

From 211 potential articles, a total of 26 were identified for a comprehensive analysis. Categorization per material was carried out as follows: IPS e.max CAD (n = 27), Suprinity PC (n = 8), Celtra Duo (n = 6), and n!ce (n = 1). The three-point bending test (3-PBT) was used in 18 articles, followed by biaxial flexural test (BFT) in 10 articles, with one of these using the four-point bending test (4-PBT) as well. The most common specimen dimension was 14 × 4 × 1.2 mm (plates) for the 3-PBT and 12 × 1.2 mm (discs) for BFT. The flexural strength values for LSGC materials varied widely between the studies.

SIGNIFICANCE

As new LSGC materials are launched on the market, clinicians need to be aware of their flexural strength differences, which could influence the clinical performance of restorations.

Evaluation of Physical-Chemical Properties of Contemporary CAD/CAM Materials with Chromatic Transition "Multicolor"

The use of materials for computer-aided design/computer-aided manufacturing (CAD/CAM) has been rapidly increasing in daily practice. However, one of the main issues regarding modern CAD/CAM materials is their aging in the oral environment, which may lead to significant changes in their overall properties. The aim of this study was to compare the flexural strength, water sorption, cross-link density (softening ratio%), surface roughness, and SEM analysis of three modern CAD/CAM "multicolor" composites. Grandio (Grandio disc multicolor-VOCO GmbH, Cuxhaven, Germany), Shofu (Shofu Block HC-Shofu Inc., Kyoto, Japan), and Vita (Vita Enamic multiColor-Vita Zahnfabrik, Bad Sackingen, Germany) were tested in this study. They were prepared in stick-shaped specimens and submitted to different tests after several aging protocols, such as thermocycling and mechanical cycle loading challenge. Further disc-shaped specimens were also created and tested for water sorption, cross-link density, surface roughness, and SEM ultramorphology, before and after storage in an ethanol-based solution. For flexural strength and ultimate tensile strength, Grandio showed the greatest values both at baseline and after aging (p < 0.05). Grandio and Vita Enamic presented the highest modulus of elasticity and the lowest water sorption (p < 0.05). A significant reduction (p < 0.05) in microhardness after ethanol storage (softening ratio%) was observed especially in Shofu. Grandio had the lowest roughness parameters compared to the other tested CAD/CAM materials, while ethanol storage significantly increased the Ra and RSm values in Shofu (p < 0.05). Despite the comparable modulus of elasticity of Vita and Grandio, this latter showed greater flexural strength and ultimate tensile strength both at baseline and after aging. Hence, Grandio and Vita Enamic may be employed for the anterior teeth and for those restorations requiring load-bearing capacity. Conversely, aging seems to affect several properties of Shofu, so its use for permanent restorations should be well-pondered based on the clinical situation.

Effect of the type of resin cement on the fracture resistance of chairside CAD-CAM materials after aging

PURPOSE

The study objective was to evaluate the influence of the type of resin cement on the flexural strength and load to fracture of two chairside CAD-CAM materials after aging.

MATERIALS AND METHODS

A polymer-infiltrated ceramic network (PICN) and a nanoceramic resin (RNC) were used to produce the specimens. Two types of dual-cure resin cements, a self-adhesive and a universal, were investigated. Bilayer specimens were produced (n = 10) and aged for 6 months in a humid environment before the biaxial flexural strength test (σ_f). Bonded specimens were subjected to a mechanical aging protocol (50 N, 2 Hz, 37℃ water, 500,000 cycles) before the compressive load test (L_f). σ_f and L_f data were analyzed using two-way ANOVA and Tukey tests (α = .05). Chi-square test was used to analyze the relationship between failure mode and experimental group (α = .05).

RESULTS

The type of resin cement and the interaction between factors had no effect on the σ_f and L_f of the specimens, while the type of restorative material was significant. RNC had higher σ_f and L_f than PICN. There was a significant association among the type of cracks identified for specimens tested in L_f and the restorative material.

CONCLUSION

The type of resin cement had no effect on the flexural strength and load to fracture of the two investigated CAD-CAM chairside materials after aging.

The Toothbrushing Effects on Surface Properties and Color Stability of CAD/CAM and Pressable Ceramic Fixed Restorations-An In Vitro Study

Pressable ceramic restorations have been introduced and investigated, and found comparable to CAD/CAM ceramic in terms of mechanical properties; however, the effect of toothbrushing on the pressable ceramic has not been thoroughly investigated. The objective of the current study was to assess the effect of artificial toothbrushing simulation on the surface roughness, microhardness, and color stability of different ceramic materials. Three lithium disilicate-based ceramics (IPS Emax CAD [EC], IPS Emax Press [EP]; (Ivoclar Vivadent AG), and LiSi Press [LP] (GC Corp, Tokyo, Japan)) were examined. For each ceramic material, eight bar-shaped specimens were prepared and subjected to 10,000 brushing cycles. Surface roughness, microhardness, and color stability (∆E) were measured before and after brushing. Scanning electron microscopy (SEM) was used for surface profile analysis. The results were analyzed using one-way ANOVA, Tukey's post hoc test, and paired sample t-test α = 0.05. The findings revealed a non-significant decrease in the surface roughness of EC, EP, and LP groups (p > 0.05), and both LP and EP have the lowest surface roughness values (0.64 ± 0.13, 0.64 ± 0.08 µm) after brushing, respectively. Toothbrushing showed a decrease in the microhardness of the three groups: EC and LP, p < 0.001; EP, p = 0.012). EP showed the lowest hardness value after brushing (862.45 ± 273.83). No significant changes (∆E) were observed in all groups (p > 0.05); however, the EC group was found to be considerably affected by color changes, in comparison to the EC and LP groups. Toothbrushing had no effect on surface roughness and color stability of all tested materials, but it decreased the microhardness. Material type, surface treatments, and glazing of ceramic materials contributed to the surface changes in the ceramic materials, necessitating further investigations in terms of the toothbrushing effect with different glazing as variables.

Flexural Strength Properties of Five Different Monolithic Computer-Aided Design/Computer-Aided Manufacturing Ceramic Materials: An In Vitro Study

Objective

The purpose of this in vitro study is to compare the flexural strength and Weibull modulus of 5 different monolithic computer-aided design/computer-aided manufacturing (CAD/CAM) ceramics.

Methods

A total of 50 specimens were fabricated, 10 from each of the following materials: lithium disilicate-based ceramic (IPS e.max CAD), zirconia -reinforced lithium-silicate ceramic (Vita Suprinity), leucite-based glass ceramic (IPS Empress CAD), and two zirconia-based ceramics (Zenostar and CopraSmile). The specimens were 4 mm wide, 2 mm thick, and 16 mm long. Flexural strength test was executed using a universal testing machine (Model 5980, Instron Industrial Products, Norwood, MA, USA). The two-parameter Weibull distribution function was used to analyze the variability of flexural strength values. Statistical analysis was performed on SPSS Version 23 (IBM Corp., Armonk, NY, USA) using one-way analysis of variance (ANOVA) and post-hoc Tukey’s test.

Results

Suprinity had the highest Weibull modulus value, while Empress CAD displayed the lowest value. One-way ANOVA showed significant difference in the flexural strength between the different materials tested (p<0.05). Post-hoc analysis revealed significant differences among all the test groups in terms of flexural strength. Zenostar presented the highest mean flexural strength value (1033.90 MPa), while Empress CAD had the lowest value.

Conclusion

High-translucency zirconia had superior flexural properties than translucent zirconia, lithium disilicate ceramics, zirconia-reinforced lithium silicate ceramics, and leucite-based glass ceramics.

In-vitro performance of subtractively and additively manufactured resin-based molar crowns

PURPOSE

To compare the in-vitro performance and wear behavior of additively or subtractively fabricated resin-based composite molar crowns for temporary and permanent application.

MATERIALS AND METHODS

Identical molar crowns (n = 8 per group) were manufactured from materials for temporary or permanent application (3x temporary additive fabrication, 3x additive permanent fabrication, 1x temporary subtractive fabrication, 1x permanent subtractive fabrication). All crowns were adhesively bonded (Calibra Universal, Dentsply Sirona, USA) on standardized resin-based composite molars (FDI 46, P Pro temporary Crown & Bridge). Thermal cycling and mechanical loading (2 × 3000 × 5°C/55 °C, 2min, H₂0 dist., 1.2 × 10⁶ force 50N) were performed and fracture force was determined (v = 1 mm/min, Z010, Zwick, Germany). Mean wear, maximum wear, and roughness were investigated on polished (P1200) specimens (n = 8 per group, d = 8 mm) in a pin-on-block test (50N; 120000 cycles; 1.6Hz; H₂O). Statistics were performed by using one-way ANOVA, Bonferroni post-hoc-tests, and Pearson-correlation (α = 0.05).

RESULTS

All crowns survived TCML without failures. Fracture forces ranged from 1362.4 ± 182.4N to 2354.1 ± 373.3N for the additive temporary crowns, from 1680.4.4 ± 525.1N to 2601.6 ± 403.7N for the additive permanent crowns, and reached values of 2988.5 ± 604.7N for subtractive temporary crowns and 3092.0 ± 307.6 N for subtractive permanent crowns. Significant (p < 0.001) differences were identified between the various additively manufactured systems, but not for the subtractively fabricated systems (p = 0.673). Mean wear of the additive temporary crowns ranged between 114.5 ± 25.8 μm and 163.8 ± 21.4 μm without significant differences (p = 0.061). Mean wear of the additive permanent crowns ranged between 120.0 ± 27.5 μm and 171.3 ± 31.8 μm with significant differences (p = 0.004). No statistically significant differences were identified between temporary and permanent subtractively manufactured specimens, with mean wear ranging between 140.5 ± 51.1 μm and 176.6 ± 26.8 μm (p = 0.673). Maximum wear of additive temporary specimens ranged between 221.4.5 ± 53.3 μm and 322.1 ± 50.6 μm; significant differences were identified between the groups (p = 0.016). Maximum wear of additive permanent specimens ranged between 246.3 ± 47.3 μm and 337.4 ± 61.4 μm, and significant differences were identified between the groups (p = 0.006). Mean wear of the subtractive group (permanent and temporary) showed no differences in maximum wear from 277.9 ± 79.7.1 μm to 316.4 ± 58.1 μm (p = 0.288). Ra roughness ranged from 0.7 ± 0.2 μm to 3.6 ± 1.3 μm with significant differences (p < 0.001) and Rz reference between 65.9 ± 26.2 μm and 16.8 ± 6.3 μm.

CONCLUSION

Temporary and permanent molar crowns provided at least acceptable in-vitro performance and fracture force for clinical mid-term application. Laboratory wear stability of the resin-based materials appeared sufficient, but should be verified under clinical conditions.

Effect of aging on color, gloss and surface roughness of CAD/CAM composite materials

OBJECTIVES

To assess the effect of aging procedures on color, gloss and surface roughness of CAD/CAM composite materials.

METHODS

6 CAD/CAM composite materials (Brilliant CRIOS, Cerasmart, Lava Ultimate, Tetric CAD, Shofu Block HC, Grandio Blocs) were tested. 10 CAD/CAM fabricated specimens of each material polished according to manufacturers' recommendations, were subjected to one of the following aging procedures; immersion in coffee (30 days, 37^οC), water thermocycling (5000 cycles, 5-55 °C) and photoaging (150,000 kJ/m²). Color, gloss and surface roughness measurements were performed before and after aging and the respective changes were calculated. Kruskal-Wallis tests, paired t-tests, one-way ANOVA and Bonferroni post-hoc tests were used for statistical analysis (a = 0.05).

RESULTS

Color changes ranged from 3.03 to 4.13 after coffee immersion, from 1.33 to 2.55 after thermocycling and from 1.02 to 2.75 after photoaging. No statistically significant differences for ΔE*_ab were found among materials after coffee immersion and thermocycling (p>0.05). Gloss changes ranged from -5.7 to -1.6 GU after coffee immersion, from -2.3 to 0.1 GU after thermocycling and from -4.4 to 0.5 GU after photoaging. No significant differences in gloss changes were found among materials after aging (p>0.05). Tetric CAD demonstrated the significantly lower gloss and the higher surface roughness after polishing. Except for gloss after thermocycling, aging procedures caused significant alteration of gloss and surface roughness parameters from baseline levels.

CONCLUSIONS

Aging procedures caused perceptible but acceptable color changes and small but visible gloss changes, while surface roughness parameters of the tested CAD/CAM composite materials were significantly affected by aging.

CLINICAL SIGNIFICANCE

Aging procedures affected CAD/CAM composite materials indicating that these materials may be prone to color and surface alterations in the oral environment that could compromise the esthetics and the performance of the restorations. Clinical studies are needed to investigate the long-term behavior of the newly introduced CAD/CAM materials.

Effect of the region of the CAD/CAM block on the flexural strength and structural reliability of restorative materials

The aim of the study was to evaluate whether the region (internal or external) of the CAD/CAM block influences the mechanical performance of restorative materials. Blocks of different CAD/CAM materials (Composites: KAV - Katana Avencia; LULT - LULT Ultimate; Ceramics: ENAM - Vita Enamic; NICE - N!CE; EMP - IPS Empress CAD; VMII - Vita Mark II; EMAX - IPS e.max CAD) were selected, and direct resin composite blocks (APX - Clearfil AP-X; FSUP - Filtek Supreme) were built using the incremental technique on a mold from one of the CAD/CAM blocks. All blocks were sectioned into bar-shaped specimens (1 × 1 × 14 mm), which were separated into two groups according to the region of the block (inside or outside). 3-point bending tests were performed following ISO 6872:2015 and flexural strength data were analyzed using one-way ANOVA and Bonferroni post-hoc tests (p < 0.05). Weibull module and characteristic strength were also calculated. In general, the mean flexural strength values were not statistically different (p > 0.05) between the inside and outside regions of each material, except for LULT (inside > outside) and EMAX (outside > inside). Comparing the materials, a similar strength (only discrete variations) was observed for inside, outside or merged (inside and outside data assembled together) regions: EMAX > KAV = LULT > NICE = APX > EMP = ENAM = VMII ≥ FSUP (merged condition). Characteristic strength at 63.2% failure probability and at 5% failure probability generally corroborates such observations. There were no statistical differences for Weibull module data (inside, outside, or merged), except for KAV and NICE (outside > inside). Thus, the region from where the restoration is milled within the CAD/CAM block generally does not influence the mechanical performance hereof (flexural strength, failure probability, risk of premature failures, and mechanical reliability) of the material, except for LULT and EMAX.

Pressable lithium disilicate ceramic versus CAD/CAM resin composite restorations in patients with moderate to severe tooth wear: Clinical observations up to 13 years

OBJECTIVE

To report the long-term clinical survival and failure rates of single-tooth restorations made of pressable lithium disilicate ceramics (LS₂ ) and CAD/CAM resin composite (RC) by two separate clinical observations.

MATERIALS AND METHODS

Twenty-one patients (12 female, nine male) were treated with 436 minimally invasive single-tooth restorations made of 274 pressed LS₂ (n = 12; posterior: monolithic IPS e.max Press; anterior: IPS e.max Ceram veneered, Ivoclar) or 162 milled from RC (n = 9; monolithic exp. CAD/CAM resin composite, Ivoclar). The mean age of patients was 44.1 ± 9.3 years and the mean observation time was 86.2 ± 13.5 months (7.7 ± 1.1 years), with 8.5 ± 2.7 years for LS2 and 6.7 ± 0.5 years for RC. All restorations were observed for technical/biological failures using the modified criteria of the United States Public Health Service (USPHS). Collected data were analyzed using Kaplan-Meier survival analysis and log-rank test (α < 0.025).

RESULTS

The 274 LS₂ restorations showed a survival of 100% and a total failure rate of 5.5%. The 162 RC restorations showed a survival of 100% and a total failure rate of 25.3%. RC restorations exhibited more material fractures (p = 0.020) and higher discoloration rates (p < 0.001).

CONCLUSIONS

Pressed LS₂ single-tooth restorations showed lower long-term failure rates than restorations made of RC.

CLINICAL SIGNIFICANCE

Despite the limitations of the clinical observations, single-tooth restorations of both materials can be recommended for permanent use in patients with severe tooth wear.

Stress analysis and risk of failure during clenching in ceramic assembly models: 3-dimensional finite element analysis

Background/purpose

Clenching is a dental parafunctional disorder that jeopardizes the life of teeth and/or dental prostheses. Computer-aided design and computer-aided manufacturing (CAD/CAM)-fabricated or 3-dimensional-printed dental prostheses are aesthetic, strong, and of good quality, but noticeable damage can still be observed after clenching. Stress analysis of synthetic ceramic assemblies with various parameters was conducted to provide data that may be used to improve the fabrication of CAD/CAM-fabricated dental prostheses.

Materials and methods

Abaqus software was used to run the simulations. A total of 96 axisymmetric finite element ceramic assembly models were simulated under 800 N vertical loading and different contact radii (0.25, 0.5, 0.75, 1.0 mm), materials (IPS e.max CAD and Vita Enamic), layer thicknesses and combinations.

Results

Four-layered ceramic assembly models produced promising results with the following parameters: contact radius of at least 0.5 mm, total thickness of at least 0.5 mm, and use of IPS e.max CAD as the first layer and Vita Enamic as the second layer without cement.

Conclusion

The ideal four-layered assembly model design uses 0.25-mm-thick IPS e.max CAD as its outer layer to simulate enamel binding and 0.25-mm-thick Vita Enamic as its inner layer to imitate the natural tooth. This design may be used as reference for prosthodontic treatment.

Effect of Successive In-office Bleaching Sessions on the Surface Properties, Substance Loss, Biaxial Flexural Strength, and Reliability of CAD-CAM Monolithic Materials

Little is known about the effects of in-office bleaching on the surface properties and on other aspects of CAD-CAM monolithic materials, especially when successive bleaching sessions are conducted. This study evaluated the effect of up to three successive in-office bleaching sessions on the microhardness, roughness, topography, substance loss, biaxial flexural strength (BFS), and reliability of CAD-CAM monolithic materials. Disks from Lava Ultimate (LU), Vita Enamic (VE), and IPS Empress CAD (EMP) were fabricated and submitted to one, two, and three bleaching sessions. In-office bleaching was performed with 40% hydrogen peroxide and each session consisted of three applications of 20 minutes each. The analyses regarding the aforementioned parameters were assessed before and after the first, second, and third bleaching sessions, except for BFS, which was evaluated at the baseline and after the third session. Weibull modulus was calculated from the BFS data. Bleaching decreased the microhardness of LU and VE from the third and second sessions, respectively, and affected neither the roughness nor the BFS of the three materials. However, in LU, it decreased the reliability and caused topographic changes, which were accentuated by the increase in the number of sessions. In general, LU and EMP showed, respectively, the highest and the lowest substance losses. Successive in-office bleaching sessions with the use of the protocol of the present study should be avoided in LU and VE.

Physical, Optical, and Mechanical Properties of Ceramic Materials after Coffee Immersion and Evaluation of Cleaning Impact with Different Oral Hygiene Tools

This study aimed to evaluate the effect of three oral hygiene tools, a regular toothbrush, an electronic toothbrush, and mouthwash, on the color stability of three different computer-aided design (CAD) and computer-aided manufactured (CAM) ceramic blocks. Feldspathic ceramic (Vita Triluxe Forte), hybrid resin ceramic (Vita Enamic), and lithium disilicate glass-ceramic (IPS e.max CAD) were used in this study. A CAD/CAM system and 81 (27 of each material) samples of ceramic blocks were used. All samples were immersed in black coffee for 15 days, and the coffee was changed twice per day. Using a spectrophotometer probe, samples on a grey background were scanned, and physical properties like surface hardness and depth were measured using interferometry and a 3D non-contact surface metrology. After 30 days of application of oral hygiene tools, instruments were used to measure various physical, mechanical, and optical properties. Vita Triluxe had the highest average color variation values (ΔE₀₀) after 15 and 30 days of immersion in coffee in both regular and electronic toothbrushes. Moreover, IPS e.max CAD had the least ΔE₀₀ values with no significant differences among the groups. The surface roughness (Ra) of the Vita Enamic ceramic increased when using a regular toothbrush, and the surface height (Rz) for the Vita Enamic ceramic increased when an electronic toothbrush was used. IPS e.max CAD had the greatest modules of elasticity forces, and Vita Triluxe Forte had the lowest when used with a regular toothbrush. The ΔE₀₀ values of the tested materials were minimally increased or decreased after 30 days of cleaning, and all were clinically acceptable. Ra and Rz were the highest for Vita Enamic in comparison to the other groups. The highest percentage in IPS e.max CAD was associated with a type 1 fracture, whereas type 3 was predominantly observed with Vita Enamic, and type 2 in the Vita Triluxe group without significant differences.

Digital Workflow for Edentulous Patients with Implant-Supported Fixed Prostheses: A Fully Digital Technique

Dentists have made prostheses using traditional methods, which are inconvenient and time-consuming. It includes functional impression taking, plaster model production, wax rim production, intermaxillary relationship and occlusal plane setting, artificial tooth arrangement, denture polymerization, polishing, etc. To make prostheses in this way, the patient has to visit the dentist several times, and it takes a long time for them to receive treatment. In addition, the potential for errors associated with the denture-manufacturing process and the use of denture materials has always existed. However, the recent use of digital technology in dentistry has made it possible to create digital prostheses. Several techniques for the immediate loading of implants with a fixed prostheses in edentulous patients have been developed. However, these techniques are partially digital techniques that include laboratory work for prosthesis fabrication. This article aimed to describe a fully digital technique for implant-supported fixed prostheses. It includes intra-oral scanning of edentulous patients, implant placement planning, and final prosthesis fabrication. This technique facilitates a simple and more efficient immediate restoration after implant placement without using stone casts.

Effect of Bonding Protocols on the Performance of Luting Agents Applied to CAD-CAM Composites

This in vitro study aimed to evaluate the effect of different bonding strategies on the micro-shear bond strength (μSBS) of luting agents to CAD−CAM composites. Surface scanning electron microscopy (SEM) and spectroscopy by energy-dispersive X-ray spectroscopy (EDS) were performed to analyze the surfaces of the composite before and after bonding treatment. Three CAD−CAM composites were evaluated: Lava Ultimate restorative (LU), Brava Blocks (BR), and Vita Enamic (VE). The LU and BR surfaces were sandblasted using aluminum oxide, while the VE surfaces were etched using a 5% hydrofluoric acid gel according to the manufacturers’ recommendations. All surfaces were subjected to the following bonding strategies (n = 15): adhesive with silane and MDP (ScotchBond Universal, 3M Oral Care, St Paul, MI, USA); adhesive with MDP (Ambar Universal, FGM, Joinville, Brazil); adhesive without silane or MDP (Prime&Bond Elect, Dentsply Sirona, Charlotte, NC, USA), pure silane without MDP (Angelus, Londrina, Brazil), and pure silane with MDP (Monobond N, Ivoclar Vivadent, Schaan, Liechtenstei). Afterwards, tygons were filled with RelyX Ultimate (3M Oral Care), AllCem (FGM), or Enforce (Dentsply Sirona), which were light-cured and subjected to the μSBS test. Data were analyzed using two-way ANOVA and Bonferroni’s post hoc test (α = 0.05). Additional blocks (n = 15) were subjected to scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) before and after the surface treatment. The μSBS values on VE surfaces were higher than those observed on LU and BR surfaces (p < 0.001). Silane without MDP (Allcem) promoted the highest μSBS values, while silane with MDP (RelyX Ultimate) provided the highest values among all bonding strategies (p < 0.001). Enforce promoted no significant difference in μSBS values. SEM and EDS analyses detected noticeable changes to the surface morphology and composition after the surface treatment. The effectiveness of the bonding strategy may vary according not only to the CAD−CAM composite but also to resin cement/bonding agent/silane used.

On the Mechanical Properties of Hybrid Dental Materials for CAD/CAM Restorations

Two hybrid dental materials available for computer-aided design and manufacturing (CAD/CAM) dental restorations have been selected to explore their potential. On the one hand, the scarcely investigated polymer-based material Vita Enamic^® (VE) and, on the other hand, the leucite-based material IPS Empress^® CAD (EC). Their micro-structure and mechanical performance were analyzed in two environments: directly as received by the manufacturer (AR), and after immersion and storage in artificial saliva (AS) for 30 days to determine the influence of the saliva effect. To avoid an inappropriate selection of materials for clinical use, a full understanding of their mechanical behavior is essential. Therefore, this investigation aims to determine the micro-structural and chemical composition by field emission scanning electron microscopy (FE-SEM) and X-ray fluorescence analysis, establishing the density, micro- and nano-hardness, the nano-elastic modulus, and the flexural strength and fracture toughness (by introducing a femto-laser notch to replicate a real crack). In addition, fracture surfaces of the broken samples were analyzed to correlate the failure micro-mechanisms with their mechanical properties. Results indicate that while the crystalline phase of the materials is very similar (composed of SiO₂ and Al₂O₃), the micro-structure and mechanical behavior is not. The material EC, with finer micro-structure, exhibits a higher mechanical performance but with greater variability of results. Furthermore, the material VE, with a 25 vol.% polymer phase, shows a mechanical performance similar to enamel and dentin and therefore more similar to human behavior.

Treatment of Tooth Wear Using Direct or Indirect Restorations: A Systematic Review of Clinical Studies

Tooth wear is considered a well-developed issue in daily clinical practice; however, there is no standard protocol for treatment. The aim of this manuscript was to systematically review the literature to evaluate the clinical outcomes of direct or indirect restorations for treating tooth wear. A literature search was conducted through the PubMed MedLine, Scopus, ISI Web of Science, Scielo, and EMBASE databases up to 29 April 2022. Clinical studies evaluating the clinical performance of direct or indirect restorations for treating tooth wear for a minimum follow-up of 6 months were included in the review. A total of 2776 records were obtained from the search databases. After full-text reading, 16 studies were included in the qualitative analysis. Considering the high heterogenicity of the studies included, a meta-analysis could not be performed. All studies included the rehabilitation of anterior and posterior teeth with extensive wear, using both indirect and direct restorations for a maximum follow-up of 10 years. Restoration materials included ceramo-metal crowns, full gold crowns, lithium disilicate ceramic, zirconia, polymer infiltrated ceramic networks, and resin composites. Most of the reports assessed the survival rate of the restorations and the clinical features using the United States Public Health Service (USPHS) Evaluation System criteria. Contradictory discoveries were perceived concerning the type of restoration with better clinical performance. Considering the current literature available, there is no evidence in the superiority of any restoration technique to ensure the highest clinical performance for treating tooth wear.

Overview of Several Typical Ceramic Materials for Restorative Dentistry

With the development of ceramic technology, prosthodontic ceramics are becoming a useful option for improving esthetic outcomes in dentistry. In this paper, various ceramic materials were reviewed and evaluated, and their advantages and disadvantages and indications in oral prosthodontics were analyzed objectively. The properties of resin-based ceramics, polycrystalline ceramics, and silicate ceramics were compared and analyzed. Resin-based ceramics may replace other ceramic materials in the CAD/CAM field.

Fractographic and Microhardness Evaluation of All-Ceramic Hot-Pressed and CAD/CAM Restorations after Hydrothermal Aging

All-ceramic dental restorations have great advantages, such as highly esthetical properties, a less complex fabrication, and a similar abrasion resistance to enamel. Despite these advantages, ceramic materials are more prone to fracture due to their brittle microstructure. The main aim of this in vitro study was to determine the difference in hot-pressed and milled glass-ceramic mechanical properties such as fracture resistance and microhardness (VHN). Four types of ceramics, two hot-pressed and two milled, feldspathic glass-ceramics and zirconia-reinforced glass-ceramics were selected in this study and tested using the static loading test and Vicker’s testing. Hydrothermal aging, consisting of different baths with temperatures between 5 degrees Celsius and 55 degrees Celsius, was chosen as the in vitro aging method. Statistical analyses are performed using SPSS Statistics software at a significance level of p < 0.05. Micro-hardness values decrease after hydrothermal aging. The static loading test reveals a significant difference between the feldspathic hot-pressed glass-ceramic, which fractures at lower forces, and milled zirconia-reinforced lithium silicate glass-ceramic, which fractures at greater forces (N). Fractographic analysis of the fractured fragments resulted in the static loading test revealing different surface features about the crack origins and propagations under a stereomicroscope.

Flexural Strength of Various Provisional Restorative Materials for Rehabilitation After Aging

PURPOSE

Durability of provisional restoration is crucial for full-mouth reconstruction, which may be influenced by aging. This study evaluated the effect of aging on the flexural strength of provisional materials for oral rehabilitation.

MATERIALS AND METHODS

Bar specimens (2×2×25 mm) were fabricated from CAD-CAM [Vita CAD-Temp^® (VC), Telio^® CAD (TC), artBloc^® (RC)], autopolymerized [Protemp™IV (PA), Luxatemp^® (LA), Unifast™Trad (UA)], and heat-polymerized polymer [Major^® C & B; (MH)]. Each was divided into aging (AG, 5000 thermocycles of 5°/55°C) and nonaging groups (NG, n = 15/group). Flexural strength (σ, MPa) was determined in a universal testing machine at 1 mm/min crosshead speed. An analysis of variance and multiple comparisons were determined for significant difference (α = 0.05).

RESULTS

TCNG indicated the highest mean of σ (133.49 ±4.32), whereas VCNG indicated the lowest mean of σ (84.62 ±3.73) for nonaging. Upon aging process, TCAG revealed the highest mean of σ (123.11 ±4.55), while VCAG possessed the lowest mean of σ (84.05 ±6.39). Significant differences among various provisional materials were indicated (p = 0.001). Aging significantly affected flexural strength (p = 0.001).

CONCLUSIONS

The CAD-CAM provisional material possessed higher flexural strength than heat-polymerized PMMA and autopolymerized PMMA, which was suggested as a provisional material for rehabilitation. Aging reduced strength for all materials tested.

Color stability of hybrid ceramics exposed to beverages in different combinations

Background

The aim of this study is to evaluate the color stability of hybrid ceramics stored in different combinations of beverages that are routinely consumed.

Methods

The specimens were prepared with resin nano-ceramic (Lava Ultimate, 3M Espe, USA) and hybrid ceramic (Vita Enamic, Vita Zahnfabrik, Germany). The specimens were aged in a thermocycler machine for 10,000 cycles. They were stored in different combinations of beverages (water, tea, coke, coffee, red wine, pomegranate juice, and turnip juice) for 12 + 12 h. Surface roughness measurements were performed using a profilometer. The specimen colors were measured using a spectrophotometer. The color values (L-a-b) of the specimens and mean surface roughness values (Ra) were recorded at the end of the 1st (D1), 7th (D7), 14th (D14) and 28th (D28) d.

Results

When the solution groups were examined, significant color changes were observed in the Lava coffee-tea, Enamic coffee-tea, Lava coffee-wine, and Enamic coffee-wine groups compared with the other groups (p < 0.01). Except for the samples in the Lava coffee-wine 28th day (D28) and Enamic coffee-wine 28th day (D28) groups, more color changes were observed in the Lava samples than in the Enamic samples across all groups and periods.

Conclusion

Greater color changes (except for the samples stored in coffee-wine) were observed in the Lava samples than in the Enamic samples across all groups and periods. It was observed that the coffee-tea and coffee-wine beverage combinations produced the greatest color change in hybrid ceramics within the limitations of this study.

Long-term effects of simulated gastric juice alternated with brushing on hardness, substance loss, flexural strength and reliability of CAD-CAM monolithic materials

OBJECTIVES

The purpose of this study is to evaluate, over a simulated 5-year period, the effect of simulated gastric juice alternated with brushing on CAD-CAM monolithic materials considering microhardness, substance loss, flexural strength, and reliability of the materials.

METHODOLOGY

Blocks from Lava Ultimate (LU), Vita Enamic (VE), IPS Empress CAD (EMP), IPS e.max CAD (EMAX), and Vita Suprinity (VS) were milled into cylinders and sliced into disks. The EMAX and VS were crystallized, and all specimens were polished with silicon carbide papers and allocated as follows: 1) artificial saliva + brushing or 2) simulated gastric juice (0.113% hydrochloric acid (HCl) solution in deionized water, pH 1.2) + brushing, simulating 1, 3, and 5 years of clinical function. Each year of clinical function was simulated by three repetitions of immersion for 3 hours in artificial saliva or simulated gastric juice followed by 1,217 brushing cycles. The microhardness and substance loss were evaluated at baseline (T0) and at each year by using a Vickers hardness tester and an analytical balance. The biaxial flexural strength (BFS) test was performed in a mechanical testing machine at the end of the 5th year. Weibull modulus was calculated from the BFS data.

RESULTS

The microhardness of the LU was not influenced by the treatment, whereas that of the other materials, in certain years, was significantly lower in the gastric juice + brushing groups in comparison with artificial saliva + brushing groups. In general, the materials did not present a significant change in microhardness over time, for either of the treatments. The LU alone showed greater substance loss in the gastric juice + brushing groups for every year. In both treatments, the LU, VE, and EMP exhibited a significant increase in the substance loss over time. The treatment did not affect the BFS of the materials. The gastric juice + brushing decreased the reliability of the VE.

CONCLUSIONS

All materials were somehow impaired by the gastric juice + brushing in at least one of the evaluated parameters, except for the BFS. However, in a deeper analysis, the LU would be the least indicated materials, followed by VE, for patients with eating disorders.

Thermoanalytical Investigations on the Influence of Storage Time in Water of Resin-Based CAD/CAM Materials

New resin-based composites and resin-infiltrated ceramics are used to fabricate computer-aided design (CAD) and computer-aided manufacturing (CAM)-based restorations, although little information is available on the long-term performance of these materials. The aim of this investigation was to determine the effects of storage time (24 h, 90 days, 180 days) on the thermophysical properties of resin-based CAD/CAM materials. Thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) were used in the study. TGA provided insight into the composition of the resin-based materials and the influence of internal plasticization and water sorption. Resin-based composites showed different decomposition, heat energy and mechanical behavior, which was influenced by storage time in water. Individual materials such as Grandio bloc showed lower influence of water storage while maintaining good mechanical properties.

Contact fracture test of monolithic hybrid ceramics on different substrates for bruxism

OBJECTIVES

To determine the minimum thickness required for a monolithic hybrid ceramic crown on different substrates (soft vs stiff) used in posterior dentition for bruxism.

METHODS

80 polymer-infiltrated ceramic networks Vita Enamic (PICN VE) disc specimens with four different occlusal thicknesses (0.8, 1.2, 1.6 and 2.0 mm), were produced using a computer-aided design/manufacturing system, and cemented on a stiff (zirconia) or soft (polyamide) substrate of 4-mm thickness. The ten specimens, in soft or stiff groups, were subjected to compressive loading by a MTS machine until fracture or maximum load (4500 N) was reached. The unbroken specimens were examined using optical coherence tomography. Eight axisymmetric finite element models and eight 3D models comprising the four different occlusal thicknesses and two substrates under different vertical loads and sliding movements were constructed. The maximum principal stress was selected to evaluate the stress distribution in this study.

RESULTS

The fracture resistance of the specimens was significantly different between the two substrates (P < 0.001). Fracture resistance was positively associated with specimen thickness (r = 0.597 and 0.896 for the soft and stiff substrate respectively). Specimens on the soft substrate had lower fracture loads, whilst cone cracks were observed in unbroken samples on different soft/stiff substrate prior to final fracture. The finite element analysis confirmed that samples on the stiff substrate had lower maximum principal stress values than those on the soft substrate. For the maximum principal stress not to exceed the flexural strength of PICN VE, a stiff substrate and minimum thickness of 2.0 mm are required for the prostheses.

SIGNIFICANCE

A minimum 2.0 mm thick, stiff substrate was needed for bruxism as shown by the effect of high/large chewing force on the posterior dentition of monolithic PICN VE crowns.

CAD/CAM Resin-Based Composites for Use in Long-Term Temporary Fixed Dental Prostheses

The aim of this in vitro study was to analyse the performance of CAD/CAM resin-based composites for the fabrication of long-term temporary fixed dental prostheses (FDP) and to compare it to other commercially available alternative materials regarding its long-term stability. Four CAD/CAM materials [Structur CAD (SC), VITA CAD-Temp (CT), Grandio disc (GD), and Lava Esthetic (LE)] and two direct RBCs [(Structur 3 (S3) and LuxaCrown (LC)] were used to fabricate three-unit FDPs. 10/20 FDPs were subjected to thermal cycling and mechanical loading by chewing simulation and 10/20 FDPs were stored in distilled water. Two FDPs of each material were forwarded to additional image diagnostics prior and after chewing simulation. Fracture loads were measured and data were statistically analysed. SC is suitable for use as a long-term temporary (two years) three-unit FDP. In comparison to CT, SC featured significantly higher breaking forces (SC > 800 N; CT < 600 N) and the surface wear of the antagonists was (significantly) lower and the abrasion of the FDP was similar. The high breaking forces (1100-1327 N) of GD and the small difference compared to LE regarding flexural strength showed that the material might be used for the fabrication of three-unit FDPs. With the exception of S3, all analysed direct or indirect materials are suitable for the fabrication of temporary FDPs.

Color Stability and Translucency of Polymer-Infiltrated Ceramic-Network Materials—A Systematic Review of the Literature

This systematic review aimed to compile information and report the color stability and translucency of polymer-infiltrated ceramic-network (PICN) materials for suitable clinical applications in dentistry. Original peer-reviewed articles in electronic databases including PubMed, MEDLINE, Scopus, and Web of Science were searched to identify relevant papers published between January 2013 and August 2020. The published papers were only in the English language and limited to in vitro studies, and experimental reports were considered. The data from nine studies were considered when reviewing the color stability and translucency of PICN in comparison to other commonly used restorative materials. Among the included studies, color stability assessment was performed in five studies, and the other four studies were involved in the combined assessment of both color stability and translucency. PICN materials are a comparatively newer class of restorative materials and are recommended to overcome the drawbacks of ceramics and resin composites. The outcomes of previous laboratory studies still do not provide convincing results regarding the optical properties of PICN materials. However, with existing sources and evidence, PICN materials exhibit less color stability than ceramics do but better color stability compared to that of resin nanoceramics (RNC) and resin composites. The translucency of PICN materials is low compared to that of ceramics, nanoceramics, and resin composites.

Stainability of different ceramic materials against mouth rinses and effect of polishing after staining

STATEMENT OF PROBLEM

Mouth rinses are known to stain tooth surfaces. However, their staining effect on different ceramics after prolonged use and the effect of polishing after staining are still unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the stainability of different ceramic materials against different mouth rinses and the effect of polishing on staining.

MATERIAL AND METHODS

Forty disk-shaped specimens were prepared from each material (total of 160 specimens): lithium disilicate (IPS e.max CAD), zirconia-reinforced lithium disilicate (VITA SUPRINITY PC), leucite-reinforced feldspar (GC Initial LRF), and resin matrix ceramic (CERASMART). Baseline color measurements (T0) were recorded with a clinical spectrophotometer (VITA Easyshade V). The specimens were immersed in chlorhexidine gluconate (CHX) 0.2% mouth rinse (Klorhex), (KLO) chlorhexidine gluconate 0.1% mouth rinse (Eludril) (ELU), a daily mouth rinse (LISTERINE Cool Mint) (LIS), artificial saliva (CON) continuously for 7 days (T1), 14 days (T2), and 28 days (T3). Discoloration values (ΔE) between the immersion time points (T0,T1,T2,T3) were calculated by using the following formula: ΔE= ([ΔL∗]² + [Δa∗]² + [Δb∗]²)^1/2. After the immersion process, specimens were polished and ΔE values remeasured. The Kruskal-Wallis and Mann-Whitney U tests were performed (α=.05) and were adjusted by postanalysis Bonferroni testing.

RESULTS

KLO caused the highest ΔE values in all groups. IPS e.max CAD had the lowest ΔE values, and CERASMART showed the highest ΔE values against all of the solutions (P<.05). However, polishing caused a decrease in the ΔE values in all groups.

CONCLUSIONS

Prolonged use of mouth rinses may cause color change in different ceramic materials. Polishing affected the color change and resulted in a decrease in ΔE values. Mouth rinses containing CHX should be recommended with caution for daily use.