Physical-chemical properties of dental composites and adhesives containing silane-modified SBA-15

L-arginine-containing mesoporous silica nanoparticles embedded in dental adhesive (Arg@MSN@DAdh) for targeting cariogenic bacteria

Dental caries is the major biofilm-mediated oral disease in the world. The main treatment to restore caries lesions consists of the use of adhesive resin composites due to their good properties. However, the progressive degradation of the adhesive in the medium term makes possible the proliferation of cariogenic bacteria allowing secondary caries to emerge. In this study, a dental adhesive incorporating a drug delivery system based on L-arginine-containing mesoporous silica nanoparticles (MSNs) was used to release this essential amino acid as a source of basicity to neutralize the harmful acidic conditions that mediate the development of dental secondary caries. The in vitro and bacterial culture experiments proved that L-arginine was released in a sustained way from MSNs and diffused out from the dental adhesive, effectively contributing to the reduction of the bacterial strains Streptococcus mutans and Lactobacillus casei. Furthermore, the mechanical and bonding properties of the dental adhesive did not change significantly after the incorporation of L-arginine-containing MSNs. These results are yielding glimmers of promise for the cost-effective prevention of secondary caries.

Determination of Water Content in Direct Resin Composites Using Coulometric Karl Fischer Titration

This study evaluated the water content and sorption of direct composites over 60 days using coulometric Karl Fischer titration (KFT). Plate-shaped specimens (10 × 10 × 1 mm³ of thickness) were built up using the composites Clearfil Majesty Posterior (CM), Grandio SO (GS), and Filtek Supreme XT (FS). Water contents were determined in non-stored specimens (control) or after storage in distilled water for up to 60 days (n = 5). The amount of water transferred from the specimens heated at 200 °C (isothermal mode) was measured in the Coulometer. The water content of non-stored specimens ranged from 0.28 to 1.69 wt% (5.6 to 31.2 μg/mm³) for GS and FS, respectively. The highest values of water sorption were observed for FS (25.3 μg/mm³ after 60 days). GS and CM showed similar water sorption after 60 days (≈9 μg/mm³), but an ultimate higher water content was observed for CM (0.9 wt%; 22.0 μg/mm³) than GS (0.7 wt%; 14.8 μg/mm³). Except for CM, no significant water sorption was observed between 21 and 60 days of storage. Since all composites presented some base water content, water sorption data alone do not account for the ultimate water content in direct resin-based composites.

Microwave-Assisted Fabrication of Mesoporous Silica-Calcium Phosphate Composites for Dental Application

Herein, the microwave-assisted wet precipitation method was used to obtain materials consisting of mesoporous silica (SBA-15) and calcium orthophosphates (CaP). Composites were prepared through immersion of mesoporous silica in different calcification coating solutions and then exposed to microwave radiation. The composites were characterized in terms of molecular structure, crystallinity, morphology, chemical composition, and mineralization potential by Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM-EDX). The application of microwave irradiation resulted in the formation of different types of calcium orthophosphates such as calcium deficient hydroxyapatite (CDHA), octacalcium phosphate (OCP), and amorphous calcium phosphate (ACP) on the SBA-15 surface, depending on the type of coating solution. The composites for which the progressive formation of hydroxyapatite during incubation in simulated body fluid was observed were further used in the production of final pharmaceutical forms: membranes, granules, and pellets. All of the obtained pharmaceutical forms preserved mineralization properties.

Bibliometric Analysis of Literature Published on Antibacterial Dental Adhesive from 1996-2020

This study aimed to investigate the current state of research on antibacterial dental adhesives. The interest in this field can be drawn from an increasing number of scholarly works in this area. However, there is still a lack of quantitative measurement of this topic. The main aim of this study was to consolidate the research published on the antibacterial adhesive from 1996 to 2020 in Web of Science indexed journals. The bibliometric method, a quantitative study of investigating publishing trends and patterns, was used for this study. The result has shown that a gradual increase in research was found, whereby a substantial increase was observed from 2013. A total of 248 documents were published in 84 journals with total citations of 5107. The highly cited articles were published mainly in Q1 category journals. Most of the published articles were from the USA, China, and other developed countries; however, some developing countries contributed as well. The authorship pattern showed an interdisciplinary and collaborative approach among researchers. The thematic evaluation of keywords along with a three-factor analysis showed that 'antibacterial adhesives' and 'quaternary ammonium' have been used commonly. This bibliometric analysis can provide direction not only to researchers but also to funding organizations and policymakers.

Mechanical behavior of restorative dental composites under various loading conditions

Mechanical engineering and its scientific principles constitute an essential core in medical science. Currently, different composite resins are widely used as restorative dental materials. However, their lack of adequate strength and toughness has led to research that is aimed at improving the mechanical properties of dental composites. In the present study, the behavior of three different dental materials is investigated under static and dynamic loading conditions. In the experimental tests, a split Hopkinson pressure bar is utilized which corresponds to the most commonly used experimental setup for examining material behavior under a high rate of loading. The examined dental composites experience impacts during their service life and also during car accidents or sport injuries. Hence, in the study, impact loading is modeled in an experiment. A series of compression tests is conducted from low to high strain rates up to 40s^-1, and the dynamic elastic moduli of three different dental composites are measured. Furthermore, studies on the compressed surface of the dental composite specimens are performed to improve the analysis with respect to the hardness of the materials. The responses of the examined composites to dynamic loadings verify the impact resistance of the materials. The results indicate the load-carrying capabilities of the dental composites. These results can be used for materials development and existing computational models.